Sony Stereo Receiver AIR A10R User Manual

4-148-281-11(1)  
Getting Started  
Messages  
Unit  
STANDBY indicator  
Tactile dot  
CANCEL : Time out without pairing.  
COMPLETE! : Pairing is completed.  
S-AIR ID A : Sets the S-AIR ID to A.”  
S-AIR ID B : Sets the S-AIR ID to “B.”  
S-AIR ID C : Sets the S-AIR ID to “C.”  
LINKED : The unit is connected to the  
S-AIR main unit.  
Remote (RM-ANU062)  
PAIRING : Pairing is in progress.  
REMOTE OFF : The unit is not  
accepting signals from the remote  
because the remote control function  
is set to “REMOTE OFF.”  
REMOTE ON : Displayed when the  
remote control disable mode is  
cleared.  
S-AIR : Displayed from the point  
power of the unit is turned on until  
connection with the S-AIR main  
unit is established.  
UNLINKED: The connection with the  
S-AIR main unit is cut off.  
/
(power)  
   
EZW-RT10A  
Wireless transceiver  
To DC IN  
6 V jack  
To a Wall socket  
Wireless Audio  
Receiver  
AC power  
adaptor  
/
(power)  
   
S-AIR indicator  
Operating Instructions  
Manual de instrucciones  
After pairing  
Hooking up the unit  
The connection is established between  
the paired main unit and sub unit.  
(reverso)  
Wireless transceiver  
Insert the supplied wireless transceiver  
(EZW-RT10A) securely into the EZW-  
RT10 slot on the rear panel of the unit.  
Check the orientation of the mark  
when inserting the supplied wireless  
transceiver (EZW-RT10A). Failure to  
do so may result in damage to the unit.  
Specifications  
Wireless transceiver  
(EZW-RT10A)  
Your system  
Neighboring  
system  
Main unit  
ID:A  
Communication System: S-AIR  
Specification version 1.0  
Frequency band: 2.4000 GHz   
2.4835 GHz  
Push to insert the wireless transceiver  
firmly until you cannot see it from the  
side.  
not connected  
Modulation method: DSSS  
Power requirements: DC 3.3 V,  
350 mA  
Remote sensor  
Dimensions (w/h/d): 50 × 13 × 60 mm  
(2 × 17 32 × 2 3/8 in)  
/
ID:A  
ID:A  
Mass: 24 g (1 oz)  
Wireless strength  
Sub unit   
Sub unit   
General  
Power requirements: 120 V AC, 60 Hz  
Dimensions (w/h/d): Approx. 166 ×  
41 × 139 mm (6 5/8 × 1 5/8 × 5 1/2 in)  
Mass: Approx. 333 g (11.7 oz) (not  
including the supplied accessories)  
AIR-A10R  
©2009 Sony Corporation Printed in China  
Pairing  
1
Place the sub unit to be paired  
near the main unit.  
Pair the main unit with the sub  
unit one at a time.  
Supplied accessories: Wireless  
transceiver (EZW-RT10A) (1)/  
Remote commander (RM-ANU062) (1)/  
R03 (size AAA) batteries (2)/  
AC power adaptor (AC-ES608K3) (1)/  
Audio cable (1)  
WARNING  
Features  
2
3
4
Check that the power of the  
main unit and the sub unit are  
turned on.  
To reduce the risk of fire  
or electric shock, do not  
expose this apparatus to  
rain or moisture.  
To reduce the risk of fire or electric  
shock, do not expose the AC power  
adaptor to dripping or splashing, and  
do not place objects filled with liquids,  
such as vases, on the apparatus.  
The AIR-A10R is an “S-AIR”  
Notes  
compatible product. It is also called the  
“S-AIR sub unit.”  
Make sure to turn off the unit when  
inserting or removing the supplied wireless  
transceiver (EZW-RT10A). Failure to do so  
may result in damage to the unit.  
Do not touch the terminals of the supplied  
wireless transceiver (EZW-RT10A).  
Do not insert any device other than the  
supplied wireless transceiver (EZW-  
RT10A) into the EZW-RT10A slot.  
Check that the S-AIR ID of the  
main unit is the same as the  
S-AIR ID of the sub unit.  
Connecting the S-AIR main unit  
(transmitter product, hereafter called  
“main unit”) with the S-AIR sub unit  
(receiver product, hereafter called “sub  
unit”) using “S-AIR” technology, you  
can use each unit in a remote location.  
For example, you can install this unit  
in the bedroom, with the music system  
connected by the audio cable, and then  
install the main unit in the living  
room. You can then listen to music  
from the main unit located in the  
living room with the music system  
connected with this unit in the  
bedroom.  
Design and specifications are subject  
to change without notice.  
Operations  
Advanced operations  
Troubleshooting  
1
Make sure the AC power  
adaptor is correctly and firmly  
connected.  
Listening to the sound of  
the connected S-AIR main  
unit  
You can use the S-AIR function to  
listen to the sound of an S-AIR main  
unit in a remote location.  
To enjoy audio of the S-AIR with this  
sub unit, connect the unit directly with  
an optional music system.  
Enjoying different sound  
source with multiple sub  
units  
Operate the S-AIR main unit to  
turn on the pairing function.  
For details on turning on the  
pairing function, refer to the  
Operating Instructions supplied  
with the S-AIR main unit.  
2
Find your problem in the  
checklist below, and take the  
indicated corrective action.  
S-AIR ID selector  
Use a main unit that can set the  
MULTI SOURCE mode.  
Set the same S-AIR ID for this unit and  
the S-AIR main unit to be connected.  
For details on setting the S-AIR ID, see  
“Establishing the connection with an  
S-AIR main unit.”  
As the main plug of AC power adaptor  
is used to disconnect the AC power  
adaptor from the mains, connect it to  
an easily accessible AC outlet. Should  
you notice an abnormality in it,  
disconnect it from the AC outlet  
immediately.  
When selecting the MULTI SOURCE  
mode, you can listen to different sound  
source with each sub unit.  
5
Press the PAIRING button on  
the rear panel of the unit using  
a pointed object.  
If the issue persists, contact your  
nearest Sony dealer.  
For setting up and details, refer to the  
Operating Instructions of the main  
unit.  
Power  
When bringing this unit in for  
repairs, be sure to bring in the entire  
system (this unit, the S-AIR main  
unit and wireless transceivers).  
This product is a system product,  
and the entire system is needed to  
determine the location requiring  
repair.  
1
Perform the procedure  
Connect the Sony AC power adaptor  
(supplied) to the DC IN 6 V jack of the  
unit firmly, and plug it into a wall  
socket.  
“PAIRING” is displayed as a  
message in the display. When  
completed, the display message  
changes to “COMPLETE!” and  
stays on for a few seconds.  
PAIRING” in the display turns on  
at the same time.  
This unit is compatible with a main  
unit with “MULTI SOURCE” mode,  
and the coupling operation. The  
coupling operation establishes a  
connection between the sub unit and  
optional S-AIR remote commander.  
described inEstablishing the  
connection with an S-AIR main  
unitand check that the S-AIR  
indicator is lit.  
The unit is not disconnected from the  
mains as long as the AC power adaptor  
is connected to the AC outlet, even if  
the unit itself has been turned off.  
To identify the unit using the  
optional S-AIR remote  
commander AIR-RM10  
(Coupling operation)  
Note on the AC power adaptor  
Use the supplied Sony AC power  
adaptor only. The polarity of the plugs  
of other manufacturers may be  
different. Failure to use the supplied  
AC power adaptor may cause the unit  
to malfunction.  
2
Check that the music system (an  
audio component, etc.) is  
securely connected to the  
AUDIO OUT L/R jacks of this  
unit.  
This unit is compatible with the  
coupling operation. The coupling  
operation establishes a connection  
between the sub unit and optional  
S-AIR remote commander. For details,  
refer to the Operating Instructions of  
the optional S-AIR remote  
Do not expose batteries or apparatus  
with battery-installed to excessive heat  
such as sunshine, fire or the like.  
To cancel pairing  
Change the S-AIR IDs of the unit and  
the S-AIR main unit to different S-AIR  
IDs.  
The remote does not function.  
Remove any obstacles between the  
remote and the remote sensor on the  
unit, and position the unit away  
from fluorescent lights.  
Point the remote at the remote  
sensor on the unit.  
Move the remote closer to the unit.  
The remote control function is off.  
Turn on the remote control function.  
The nameplate is located on the  
bottom exterior.  
To stop the pairing operation  
3
4
Turn on the music system and  
operate it to output sound.  
Owners Record  
Music system  
AIR-A10R  
commander.  
midway  
The model and serial numbers are  
located on the bottom of the unit.  
Record these numbers in the space  
provided below. Refer to them  
whenever you call upon your Sony  
dealer regarding this product.  
Press the PAIRING button again.  
When coupling is in progress,  
“COUPLINGis displayed.  
When completed, the display message  
changes to “COUPLING OK” and  
stays on for a few seconds. “CPL” in  
the display turns on at the same time.  
Press S-AIR CH +/– repeatedly  
to select the desired S-AIR  
jacks  
AUDIO OUT L/R (white/red)  
To pair the main unit with  
multiple sub units  
Precautions  
channel of the S-AIR main unit.  
Connect an optional music system,  
such as an audio component, to the  
jacks using the supplied audio cable.  
Match the color of the jacks with those  
of music system when connecting.  
Repeat steps 1 through 5.  
Depending on the connected  
S-AIR main unit, the operation  
may differ. For details, refer to the  
Operating Instructions supplied  
with the S-AIR main unit.  
Notes on use of the S-AIR  
The S-AIR indicator is turned  
Inserting the batteries in  
the supplied infrared  
remote  
Slide and remove the battery  
compartment lid, and insert the two  
supplied R03 (size AAA) batteries,   
side first, matching the polarities  
shown below.  
Model No.  
Serial No.  
product  
About the error message when setting  
the coupling operation  
off.  
As the S-AIR product transmits  
sound by radio waves, sound may  
skip when radio waves are  
Check that the AC power adaptor is  
connected securely and the unit is  
turned on.  
NOTE:  
“INVALID” is displayed if the S-AIR  
main unit is not compatible with the  
MULTI SOURCE mode or the  
coupling operation.  
“FAILED” or “ERROR” is displayed if  
an error occurs while setting the  
coupling operation.  
This equipment has been tested and  
found to comply with the limits for a  
Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are  
designed to provide reasonable  
protection against harmful interference  
in a residential installation. This  
equipment generates, uses and can  
radiate radio frequency energy and, if  
not installed and used in accordance  
with the instructions, may cause  
harmful interference to radio  
White  
To operate the S-AIR main unit  
obstructed. This is a characteristic of  
radio waves and is not a  
Check that the supplied wireless  
transceiver is inserted securely in the  
unit.  
from the unit  
malfunction.  
You can perform the following  
operations using the buttons on the  
remote or unit.  
As the S-AIR product transmits  
sound by radio waves, equipment  
that generates electromagnetic  
energy, such as a microwave oven,  
may interfere with sound  
Connecting the unit and S-AIR  
main unit is not possible. (The  
S-AIR indicator flashes.)  
Check that the supplied wireless  
transceiver is inserted securely to the  
unit.  
If you use another S-AIR main unit,  
place it more than 8 m (26 1/4 feet)  
away from the S-AIR main unit you  
are using.  
Confirm the S-AIR IDs of the unit  
and the S-AIR main unit.  
The main unit is paired with another  
S-AIR sub unit. Pair the main unit  
with the sub unit you are using.  
The main unit is paired with another  
S-AIR sub unit. Cancel pairing.  
Place so that the unit and the S-AIR  
main unit are separated from other  
wireless devices.  
Stop using any other wireless  
devices.  
The connected S-AIR main unit is  
turned off. Turn on the S-AIR main  
unit.  
To  
Press  
For details on the coupling operation,  
refer to the Operating Instructions of  
the optional S-AIR remote  
commander.  
Start playback.  
Stop playback.  
Pause playback.  
Select sound source.  
Select track.  
transmission.  
As the S-AIR product uses radio  
waves that share the same frequency  
as other wireless systems, such as  
wireless LAN or Bluetooth devices,  
interference or poor transmission  
may result. In this case, take the  
following steps:  
Red  
S-AIR CH +/–  
/  
communications. However, there is no  
guarantee that interference will not  
occur in a particular installation. If this  
equipment does cause harmful  
interference to radio or television  
reception, which can be determined by  
turning the equipment off and on, the  
user is encouraged to try to correct the  
interference by one or more of the  
following measures:  
Reorient or relocate the receiving  
antenna.  
Increase the separation between the  
equipment and receiver.  
Connect the equipment into an  
outlet on a circuit different from  
that to which the receiver is  
connected.  
Consult the dealer or an  
experienced radio/TV technician  
for help.  
Depending on the connected S-AIR  
main unit, the operation may differ.  
Refer to the Operating Instructions of  
the S-AIR main unit.  
To a music system  
(not supplied)  
Notes on using the remote  
Do not install the S-AIR product  
near other wireless systems.  
Do not use S-AIR product and  
the other wireless systems at the  
same time.  
The transmission distance differs  
depending on the usage  
environment. Find a location where  
transmission between the unit and  
the S-AIR main unit is most  
effective, and install the unit and the  
S-AIR main unit there.  
With normal use, the batteries should last  
for about six months.  
Do not mix an old battery with a new one  
or mix different types of batteries.  
If you do not use the remote for a long  
period of time, remove the batteries to  
avoid damage from battery leakage and  
corrosion.  
Establishing the  
connection with an S-AIR  
main unit  
Connect the unit and S-AIR main unit  
to listen to sound from the S-AIR main  
unit.  
You can easily establish the connection  
by setting the same S-AIR ID for this  
unit and S-AIR main unit.  
Note  
When the main unit is used in combination  
with an iPod or iPhone, S-AIR unit button  
operation of the iPod or iPhone will be as  
follows.  
Operations with S-AIR  
units  
Status of  
iPod or  
iPhone  
or   
Pause  
Playback  
Pause  
Off  
Pause  
On safety  
Playback  
Playback  
No change  
LCD on  
1
Operate the S-AIR main unit to  
turn on the S-AIR function.  
Operate the unit only on the power  
sources specified in “Specifications.  
Completely disconnect the AC  
power adaptor from the wall socket  
(mains) if it is not going to be used  
for an extended period of time.  
When unplugging the AC power  
adaptor, always grip the AC power  
adaptor. Never pull by the cord itself.  
Should any solid object or liquid get  
into the unit, unplug the unit, and  
have it checked by qualified  
The S-AIR channel fails to  
change.  
For details on turning on the S-AIR  
function, refer to the Operating  
Instructions supplied with the  
S-AIR main unit.  
Check that the unit and the S-AIR  
main unit are connected properly.  
When using the Wireless Audio  
Transmitter for PC as the S-AIR  
main unit, sub unit operations will  
not be functional if supplied PC  
application is not booted or  
Standard Mode is selected.  
Changing the display  
CAUTION  
To change the information on  
You are cautioned that any changes or  
modifications not expressly approved  
in this manual could void your  
authority to operate this equipment.  
the display while the unit is on  
2
Set the S-AIR ID of the unit to  
the same S-AIR ID as the S-AIR  
main unit to be connected.  
Press DISPLAY.  
Each time you press the button, the  
display changes as follows:  
For the wireless transceiver (EZW-RT10A)  
This device complies with Part 15 of  
the FCC Rules. Operation is subject to  
the following two conditions: (1) this  
device may not cause harmful  
interference, and (2) this device must  
accept any interference received,  
including interference that may cause  
undesired operation.  
For details on setting the S-AIR ID  
of the S-AIR main unit, refer to the  
Operating Instructions supplied  
with the S-AIR main unit.  
When the unit is connected to an S-AIR  
main unit:  
Information of connected main unit   
Model name of connected main unit  
...  
There is no sound.  
personnel before operating it again.  
If you use another S-AIR main unit,  
place it more than 8 m (26 1/4 feet)  
away from the S-AIR main unit you  
are using.  
On placement  
3
Press  to turn on the unit.  
At low temperature, characters  
change in the display more slowly,  
but it is not a malfunction.  
Once the connection is established,  
the S-AIR indicator on the unit  
lights up and “LINKED” appears in  
the display for a few seconds.  
Confirm the S-AIR IDs of the unit  
and the S-AIR main unit.  
Up to 16 characters of information can  
be displayed.  
Do not place the unit in an inclined  
position or in locations that are  
extremely hot, cold, dusty, dirty,  
humid or lacking adequate  
Check the pairing setting.  
Place so that the unit and the S-AIR  
main unit are closer.  
This equipment must not be co-located  
or operated in conjunction with any  
other antenna or transmitter.  
When the unit is not connected to an  
S-AIR main unit:  
“S-AIR” “UNLINKED” ...  
Identifying the main unit  
with a specific sub unit  
(Pairing operation)  
It is easy to set the same S-AIR ID for  
the main unit and the sub units to  
establish the connection.  
However, if a neighbor has an S-AIR  
main unit with the same S-AIR ID as  
your S-AIR main unit, the neighbor  
may be able to hear the audio  
Stop using any equipment that  
generates electromagnetic energy,  
such as a microwave oven.  
ventilation, subject to vibration,  
direct sunlight or a bright light.  
Be careful when placing the unit on  
surfaces that have been specially  
treated (for example, with wax, oil,  
polish) as staining or discoloration  
of the surface may result.  
This equipment complies with FCC  
radiation exposure limits set forth for  
uncontrolled equipment and meets the  
FCC radio frequency (RF) Exposure  
Guidelines in Supplement C to OET65.  
Turning off the supplied  
infrared remote control  
function  
In addition to the unit you already  
have, you can connect other S-AIR sub  
units to a single S-AIR main unit and  
use them together.  
Place so that the unit and the S-AIR  
main unit are separated from other  
wireless devices.  
Stop using any other wireless  
devices.  
This equipment should be installed  
and operated with at least 20cm and  
more between the radiator and person’s  
body (excluding extremities: hands,  
wrists, feet and ankles).  
On heat buildup  
Change the S-AIR ID settings of the  
unit and the S-AIR main unit.  
Turn off the unit and S-AIR main  
unit and then turn them on again.  
Check that the AC power adaptor is  
connected securely and the unit is  
turned on.  
Heat buildup in the unit during  
operation is normal and is not cause  
for alarm.  
However, when using multiple S-AIR  
sub units near each other, all the S-AIR  
sub units may receive the same signal  
from the remote and the connected  
S-AIR main unit may not function  
properly. To prevent this, you can turn  
off the remote control function of the  
S-AIR sub units.  
transmitted from your S-AIR main  
unit on the neighbors system. Also,  
you may be able to hear the audio  
transmitted from your neighbors  
S-AIR main unit on your system. To  
prevent this, you can identify the main  
unit with a specific sub unit by  
Cleaning the cabinet  
“S-AIR” and its logo are trademarks of  
Clean the cabinet with a soft dry cloth.  
Do not use any type of abrasive pad,  
scouring powder, or solvent, such as  
thinner, benzine, or alcohol.  
Sony Corporation.  
The Bluetooth word mark and logos are  
owned by the Bluetooth SIG, Inc. and any  
use of such marks by Sony Corporation is  
under license. Other trademarks and trade  
names are those of their respective owners.  
iPod is a trademark of Apple Inc.,  
Increase the volume of the  
connected music system.  
There is noise or the sound  
performing the pairing operation.  
Use buttons on the S-AIR sub unit  
whose remote control function you  
want to turn off.  
skips.  
S-AIR (Sony Audio  
Before pairing  
If you use another S-AIR main unit,  
place it more than 8 m (26 1/4 feet)  
away from the S-AIR main unit you  
are using.  
Interactive Radio frequency)  
Recent times have seen the rapid  
spread of DVD media, Digital  
Broadcasting, and other high-  
quality media.  
registered in the U.S. and other countries.  
iPhone is a trademark of Apple Inc.  
The connection is established by the  
S-AIR ID (example).  
1
2
Press  to turn off the unit.  
All other trademarks and registered  
trademarks are of their respective holders.  
In this manual, and marks are not  
Your system  
Neighboring  
system  
Press and hold S-AIR CH+, and  
then press .  
Place so that the unit and the S-AIR  
main unit are closer.  
®
specified.  
To ensure that the subtle nuances of  
these high-quality media are  
transmitted with no deterioration,  
Sony has developed a technology  
called “S-AIR” for the radio  
transmission of digital audio signals  
with no compression, and has  
incorporated this technology into  
the EZW-RT10A.  
This technology transfers digital  
audio signals with no compression  
using the 2.4 GHz band range of  
ISM band (Industrial, Scientific, and  
Medical band), such as wireless  
LANs and Bluetooth applications.  
Stop using any equipment that  
generates electromagnetic energy,  
such as a microwave oven.  
Place so that the unit and the S-AIR  
main unit are separated from other  
wireless devices.  
“REMOTE OFF” is displayed, and  
the setting is complete. Even when  
you try controlling the unit using  
the remote, “REMOTE OFF” is  
displayed and the unit will not  
accept the signal from the remote.  
Main unit  
ID:A  
Stop using any other wireless  
devices.  
Change the S-AIR ID settings of the  
unit and the S-AIR main unit.  
Do not place a mobile phone near  
the unit and the S-AIR main unit, as  
this may result in noise.  
To turn on the remote control  
function  
Perform steps 1 and 2 above and check  
that “REMOTE ON” appears in the  
display.  
ID:A  
ID:A  
Sub unit   
Sub unit   
Note  
Even when the remote control function is  
turned off,  on the remote will continue  
to function.  
 

Sharp PDAs Smartphones El 6850 User Manual
Sony Blu ray Player 4 169 142 111 User Manual
Sony Cassette Player WM FX281 User Manual
Sony Computer Drive MSH 128S2 User Manual
Sony Microcassette Recorder ICD ST20 User Manual
Sony Speaker SS K70ED User Manual
Speco Technologies Security Camera CVC 320WP User Manual
Subaru Robin Power Products Portable Generator RGD2510 User Manual
Sunbeam Bread Maker BM7850 User Manual
SVA Flat Panel Television VR2018W User Manual