Operations Manual
®
TABLE OF CONTENTS
Section 1: INSTALLATION PREPARATION . . . . . . . . . . . . . . . 2
Parts Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . 2
Alternative Transducers and Mounting Methods. . . . . . 4
Transducer Exchange . . . . . . . . . . . . . . . . . . . . . . . . . 5
Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 2: USING THE 105SX. . . . . . . . . . . . . . . . . . . . . . . 6
How Sonar Works . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Simulator Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 7
What You See On Screen . . . . . . . . . . . . . . . . . . . . . . 8
Control Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section 3: ADVANCED FEATURES. . . . . . . . . . . . . . . . . . . 21
Using the Diagnostic Feature. . . . . . . . . . . . . . . . . . . 21
Section 5: MAINTENANCE AND WARRANTY. . . . . . . . . . . 22
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Service Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Customer Resource Center . . . . . . . . . . . . . . . . . . . . 28
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
P/N 531082-1 R11012E
INSTALLATION PREPARATION
PARTS SUPPLIED
PARTS SUPPLIED
Before installing your 105SX, please ensure the following parts are
included in the box:
• 105SX fishfinder
• Transducer with 20' (6m) of cable and mounting hardware kit
• Mounting system and mounting hardware kit
• 6' (2m) power cable
• Publications kit
• Temperature Probe
If any of these items is missing, call our Customer Support Hotline.
ACCESSORIES
Humminbird offers a wide assortment of accessories that complement
and expand the capability of your new 105SX. These accessories are
designed with the same high standards and are backed by the same one-
year warranty. The Humminbird Accessory catalog included with your unit
contains descriptions of the many accessories available and ordering
information. All Humminbird accessories are available through your full-
service Humminbird dealer or factory direct through our number listed in
the Customer Support section.
INSTALLATION OVERVIEW
The 105SX consists of two primary components to install: the control
head and the transducer.
The control head contains the sonar transmit and receive circuitry, as well
as the user controls and display. It should be installed in a location that
provides access to the controls and visibility while in use. The control
head mounts on a quick disconnect mounting system that swivels and
tilts providing flexibility for viewing from almost anywhere on the boat.
The transducer converts electrical energy from the transmitter into
mechanical pulses or sound waves. The transducer also receives the
reflected sound waves and converts them back into electrical signals for
display on the control head. It should be installed in contact with the
2
INSTALLATION PREPARATION
INSTALLATION OVERVIEW
surface of the water in an area that has smooth water flow - usually on
the transom of the boat. There are several mounting options for the
transducer. Review the following section to determine the method that
works for you and your boat.
Determining How to Mount the Transducer
The 105SX includes a model XHS- 6-24 transducer. This transducer can be
mounted on the transom of the boat, or bonded to the inside of a
fiberglass hull boat.
The transom installation, which is the
most widely used, places the
transducer on the outside of the boat
hull. This technique produces the least
signal loss, and provides a way to
adjust the transducer after installation.
As an alternative to transom mounting,
it is possible on many fiberglass-hulled
boats to glue the transducer on the
inside of the boat hull. Since fiberglass
Transom Mounted Transducer
has similar sonar characteristics as
water, the sonar signal can pass through the boat hull with minimal loss.
The hull of the boat must be single layer construction (not double-hulled).
Also, any air trapped in the lamination of the fiberglass would prevent the
sonar signal from passing through.
Inside the hull installations require
no holes be drilled into the boat and
through experimentation, high-
speed operation comparable to
transom mounting can be achieved.
Two part, slow cure epoxy (not
included) is required to glue the
transducer in place.
Inside the Hull Mounted Transducer
3
INSTALLATION PREPARATION
ALTERNATE TRANSDUCERS AND MOUNTING METHODS
ALTERNATE TRANSDUCERS AND MOUNTING METHODS
The 105SX comes with everything necessary for installation and operation
on most boats. However, there are several situations which may require a
different type of transducer. Inboard boats, wood or metal hulls, and sail
boats create unique transducer mounting needs. Alternate transducers
and mounting methods are detailed below.
Portable Mounting
The standard transducer can be adapted for portable installations using
part number
MHX-SPT. This accessory adapts your transducer to a suction cup mount
for temporary installation on the boat hull or other surface.
Trolling Motor Mounting
The standard transducer can also be adapted
to mount on most trolling motors using part
number AD-STM. This accessory includes a
bracket and hose clamp that allows
mounting the transducer to the body of
most trolling motors.
Thru-Hull Mounting
Thru-hull transducers install through a hole
drilled in the hull of the boat. Larger boats or
boats with inboard motors create turbulence
that make transom mounting ineffective. Also,
hulls that are very thick or are double layered,
or made from materials such as wood or
metal, (which do not conduct sonar signals)
make inside the hull mounting inadvisable.
Thru-hull mounting may require the use of a
fairing block to level the transducer with the
waterline. Also, since special tools and
knowledge may be required to perform this
type of installation it is best to refer to a
qualified marine technician.
4
INSTALLATION PREPARATION
TRANSDUCER EXCHANGE
TRANSDUCER EXCHANGE
Other transducers are available as replacements for the standard
transducer. You may exchange your new and unassembled transducer for
another type by returning it to the address listed in Customer Support.
Some transducers may have additional costs. Refer to the Accessory cata-
log or call Customer Support for information.
BEGINNING INSTALLATION
Now that you have determined the transducer mounting method, you
can begin installation of the 105SX. The fold out installation guide
included provides detailed step by step instructions for installation of the
control head and transducer. For transom mount transducer installations,
you will need the mounting template in the center of this manual.
In addition to the parts included you need the following for installation
and operation:
• A powered hand drill and various drill bits
• Phillips and flat-head screw drivers
• A ruler or measuring tape
• Pen or pencil
• 12 volt power source (your boat’s battery)
• A 1-amp fuse
• A fuse holder (if you are wiring directly to the boat’s battery)
• Silicone sealant (for sealing drilled holes)
• 2-part, slow-cure epoxy (for inside the hull transducer installations)
5
USING THE 105SX
HOW SONAR WORKS
HOW SONAR WORKS
Your Humminbird unit uses sonar to
locate and define underwater
objects, define the bottom terrain, as
well as determine distance.
Sonar technology is based on sound
waves. Your Humminbird unit sends
out a sound wave signal. With this
signal it determines distance by
measuring the time between the
transmission of the sound wave and
when the sound wave is reflected off
an object. Your Humminbird uses the
reflected signal to interpret location,
size and composition of an object.
Sonar is very fast. A sound wave can travel from the surface to a depth
1
4
of 600' (185m) and back again in less than / of a second. It is unlikely
that your boat can "outrun" this sonar signal.
The 105SX is a 200kHz, single-beam fishfinder. The 200 kHz frequency
provides excellent sonar resolution (the ability to distinguish small
returns or returns which are close to the bottom), while providing depth
capabilities to 600’ (185m). The shape of the sonar beam is symmetrical
and covers an area of approximately 24 degrees side to side and front to rear.
Actual depth capability depends on factors such as bottom hardness,
water conditions, and transducer installation. Units will typically read to
deeper depths in fresh water than in salt water
6
USING THE 105SX
SIMULATOR OPERATION
SIMULATOR OPERATION
The 105SX contains a simulator that allows you to use the unit as if you
are on the water. The simulator is invaluable for learning how to operate
the 105SX.
There are two ways to start the simulator. If
the unit is powered off, press and hold the
POWER button for approximately three
seconds until you hear a continuous chirp.
The simulator can also be started by
selecting the Simulator option on the start-
up screen after you power-up the unit.
When this screen is shown, simply press the
DOWN ARROW until “Simulator” is highlighted. When the screen times
out, the unit will be in simulator mode.
When in simulator operation, the 105SX responds to control inputs as if
it is in actual operation, so feel free to experiment, or to customize the
unit for your particular operation.
To exit Simulator mode, power the unit off.
When in simulator mode, the word “simulator” will flash on and
off in the top center part of the display.
FEATURE MEMORY
If your 105SX is installed with a transducer connected, any changes you
make to the set-up while in Simulator are retained in the unit’s memory.
This allows you to use simulator to experiment with the various set-up
options, and retain your selected settings for normal operation.
7
USING THE 105SX
WHAT YOU SEE ON-SCREEN
If you are using the 105SX in Simulator when no transducer is connected,
any selected options are lost when the unit is powered off. The 105SX
will return to Factory Settings, or options selected when last used with a
transducer, if no transducer is connected.
IMPORTANT: A transducer must be connected to the 105SX in
order to retain user settings selected when in simulator mode. If
no transducer is detected, the unit defaults to pre-selected options
when powered off.
Figure A
What You See On-Screen
Your 105SX uses a 128 x 64 matrix
FSTN LCD display. This display provides
outstanding viewability in all light
conditions over a wide range of
temperatures.
At initial power-up, the 105SX uses
settings that were set at the factory.
After initial use, the 105SX will
remember the settings you enter.
There are several elements on-screen
that are common to all modes of
operation.
Speed/Temperature. The initial screen layout takes one of two basic forms
depending on presence of accessories such as Temperature or
Speed/Temperature sensors. Figure A shows the default view when the
Speed/Temp or Temperature accessory is installed. Figure B shows the default
view when no accessory is installed.
Depth. The digital depth number shows the water depth directly beneath
the transducer location.
Depth Range. The depth range is shown to the right of the screen. The
upper number is 0 indicating the surface of the water. The lower number
is one of the nine depth ranges available that best match the depth of
the water. As the depth of the water changes, the range changes as
necessary in order to retain a bottom representation on-screen.
8
USING THE 105SX
WHAT YOU SEE ON-SCREEN
Bottom Depiction
Zero Line
When in Auto mode, the horizontal
line at the top of the screen is the
“zero line,” representing the surface
of the water. Occasionally there is a
gap in this line. This gap indicates
the unit is updating the display even
if the bottom is not visible on-
screen, or if the bottom information
is not changing.
New sonar information appears on
the right side of the graphic area of
the display and moves to the left as
new information is displayed. The
105SX automatically selects the
appropriate depth range to show
the depth of water beneath the
transducer. This range is selected so
Water Depth
Depth Range
Figure B
2
3
the bottom representation is typically shown about / down the display.
Bottom. The graphic depiction of the bottom provides an effective tool for
understanding the composition of the
bottom. If the bottom is hard and
smooth, the bottom depiction is narrow
and dense. If the bottom is soft mud or
sand, the depiction will be thick and
less dense. This indicates much of the
signal is absorbed by the soft bottom. If
the bottom is rocky or rugged in
Surface Clutter
Rocky Bottom
composition, the depiction is of varying
density and textured in appearance.
Wave action also affects the bottom
depiction. The information drawn is
a distance measurement, so if the
boat is moving up and down over
flat bottom, the bottom depiction
often appears in regular variations
that match wave timing.
Soft Bottom
Hard Bottom
9
USING THE 105SX
WHAT YOU SEE ON SCREEN
Structure. Structure is defined as any object physically attached to the
bottom. The sonar configuration of the 105SX is optimized to give the
most accurate depiction of bottom structure possible. Grass, trees,
stumps, wrecks or other debris are accurately displayed, however the
depiction of these objects varies with boat speed and direction. The best
way to learn to interpret structure is to operate the 105SX over a variety
of known conditions and experiment with user functions to best
represent those conditions on-screen.
Surface Clutter. Surface clutter is the layer of water near the surface that
is rich in algae and other growth, and often is aerated by wind or wave
action. This area of water interferes with sonar transmission and often
appears on-screen as regular clusters of individual dots near the “0” line.
Thermoclines. Thermoclines are sharp differences in water temperature.
These are easily identified by the continuous nature of the return.
Second Returns. When a sonar signal is reflected off the bottom back to
the transducer, there is often
enough energy left in the signal to
Thermocline Second Return
be reflected off the surface of the
water back to the bottom a second
time. Second returns appear as a
slightly weaker bottom
representation exactly twice the
depth of the primary bottom return.
The second return is most likely to
occur in shallow water and in areas
of relatively hard bottom.
Fish ID. The 105SX uses advanced
signal processing to further evaluate
any sonar return between the
surface and the bottom. For
instance, a small school of bait fish
usually appears as a dense cluster of individual dots. If the return meets
certain additional criteria, a fish symbol is assigned. There are three
different size fish symbols used to indicate the intensity of the sonar
return. While signal intensity is a good indicator of relative fish size,
10
USING THE 105SX
CONTROL FUNCTIONS
+
ID Fish
different species of fish have different
sonar characteristics, so it is not always
possible to distinguish fish size
Depth
between varying species. The signal
intensity is “normalized” for depth so a
small fish close to the boat does not
appear as a large fish symbol.
+
ID adds an additional piece of
information to help the user locate fish.
On selected fish symbols, the digital
depth of the designated fish is drawn
to help locate the fish vertically.
CONTROL FUNCTIONS
The 105SX uses a simple five button
keypad for all user input. Press any
button and an audible “chirp” confirms
the control input. If a button has no function or is
inappropriate for the situation, an audible “error”
is heard. The unit sounds multiple chirps.
Power. The Power button powers the 105SX up
for normal operation. When the unit is on,
POWER turns the unit off. POWER can also be
used to go directly into Simulator mode. To enter
simulator, with the unit powered off, press and
hold POWER for several seconds until a
continuous chirp is heard.
Light. LIGHT controls the unit’s display backlight.
With the unit powered on, press LIGHT once to
turn the backlight on “high.” Press LIGHT a second time to turn the
backlight on “low,” and a third time turns the backlight off. The backlight
is very effective for low-light and nighttime operation. When the backlight
is on, the 105SX will consume more power than with the backlight off. This
is important when using the 105SX in a portable configuration powered by
a separate battery, or when powering the unit from a trolling motor battery.
11
USING THE 105SX
CONTROL FUNCTIONS
When powering the unit from a battery such as in portable applications,
you can prolong the battery life by using the backlight at a minimum.
The three lower buttons, MENU, UP ARROW, and DOWN ARROW work
together to control the 105SX menu-controlled user functions.
Menu. MENU displays a menu on-
screen for adjustment. In normal
operation, pressing MENU repeatedly
cycles through all available menu
headings. When a menu heading
Menu Heading
displays, the full menu appears after a short pause. A menu remains on-
screen for several seconds, and can be adjusted by using the ARROW
keys. If no adjustment is made in the allotted time, the menu disappears.
If you want the menu to remain on-screen longer press and hold
MENU—the menu will remain on-screen indefinitely. Once you release the
menu button, the screen will time out. Once a menu times out, it is still
considered the active menu. Press MENU to bring up the last menu used.
Arrow Keys. The UP ARROW and DOWN ARROW make adjustments to
menu functions. On the left side of every menu there are UP ARROW and
DOWN ARROW symbols. The symbols indicate which ARROW button has
a function in a particular situation. Either one or both ARROW buttons
can be used to adjust the menu function. A hollow ARROW symbol
means the corresponding ARROW button has no function. Pressing that
button will result in no adjustment and the “error” audible will be heard.
A solid ARROW symbol means the corresponding ARROW button can be
used to affect the menu adjustment.
The ARROW buttons often can be used when no menu is on-screen. In
these situations, pressing the ARROW button twice affects the function
of the active (last-used) menu. This is a short-cut to menu operation. The
menu appears on-screen while the adjustment is made and times out. A
frequently used menu can be adjusted very quickly using this technique.
After an adjustment is made to a menu function, the menu times out
after a few seconds and the unit returns to normal operation.
12
USING THE 105SX
CONTROL FUNCTIONS
Menu Layout. All menus use the same
basic layout. The heading at the top
describes the menu function. The UP
ARROW and DOWN ARROW symbols to
the left of the menu indicate which
buttons are available for adjustment. In
menus that have several possible settings,
a range of adjustment indicator shows the total range available and the
current setting.
Within the menu are the options available. The selected option or current
setting is highlighted in the black box. If no adjustment is made, this is
the selected setting. Press an ARROW button while the menu is displayed
to select another option.
Several of the menus are multi-step. In some situations if an adjustment is
made, additional options become available for further adjustment.
Examples of these multi-step menus are Depth Range, Depth Alarm and
Zoom. See the detailed description of each function for further
explanation.
Heading
Up Arrow Option
Arrow Symbols
Selected Setting
Down Arrow Option
Range of Adjustment Indicator
13
USING THE 105SX
MENU FUNCTIONS
Menu Functions
Sensitivity. The Sensitivity function controls
the sensitivity of the sonar receiver. The
105SX automatically adjusts the level of
receiver sensitivity based on a number of
factors including the depth of the water
and the level of noise present. Noise can be
caused by other electronic devices, engines,
trolling motors, propeller cavitation and
hydrodynamic flow among others.
The user has the option of adjusting
the Sensitivity higher or lower based
on personal preference. You can select
one of 11 sensitivity settings from -5
to +5. A setting of 0 (factory setting)
has no effect on the automatic
(+)High Sensitivity (-)Low Sensitivity
sensitivity control. Increasing the
sensitivity (+1 through +5) enables the
unit to display the information from
progressively smaller sonar returns. By
decreasing the sensitivity bias (-1
through -5), the unit effectively filters
small sonar returns.
In murky or muddy water, it is often
helpful to reduce the sensitivity. This
prevents the display from being
Sensitivity at “0”
cluttered with sonar returns from debris or suspended particles. In very
clear or very deep water, it may be helpful to increase the sensitivity since
even the smallest sonar return may be of interest to the user.
To adjust Sensitivity, press MENU repeatedly until the Sensitivity heading is
displayed. When the Sensitivity menu appears, use the UP ARROW to
increase the sensitivity, or the DOWN ARROW to reduce sensitivity. To
sequence through the available settings, press and hold either ARROW
button. Release the button at the setting you want to change.
14
USING THE 105SX
MENU FUNCTIONS
After an adjustment is made, the menu disappears and the new
sensitivity setting is in affect. If additional time is needed to study a
menu, press and hold the MENU button and the menu will remain on-
screen indefinitely. If you need to make an additional adjustment, press
the UP ARROW or DOWN ARROW button.
Depth Range. The Depth Range function
controls the vertical distance displayed on
the graphic area of the display. There are
nine depth ranges available. The top of
the range is always 0, or the surface of
the water. Ranges of 0–15', 0–30', 0–60',
0–120', 0–180', 0–240', 0–360', 0–480' and 0–600' are available. The
range that positions the bottom depiction closest to the bottom of the
screen, will best utilize the available display resolution.
The 105SX automatically adjusts the
depth range depending on the depth of
the water. The unit tries to maintain the
2
3
bottom depiction about / down the total
range (for example, in 20' (6m) of water,
the 0-30' (0-10m) range would be
selected). This provides the best display
resolution and therefore the best target
separation possible.
The Depth Range can be adjusted manually. Press MENU repeatedly until
the Depth Range menu is visible. Two options are available:
Auto and Manual.
The manual setting enables you to adjust
the current depth range setting. The unit
no longer adjusts the Depth Range to the
most appropriate range for bottom display.
Often, the bottom may not be visible on-
screen. The digital depth readout always
determines the depth of the bottom, even
if it is not visible on-screen.
15
USING THE 105SX
MENU FUNCTIONS
Using manual Depth Range control, you
can view sonar information from the
area near the surface in greater detail.
To return to automatic Depth Range
control, press the MENU button until
the Depth Range menu appears on-
screen and use the UP ARROW to
select AUTO.
Zoom. Zoom is similar to Depth
Range because it controls the range of
information displayed on screen.
Zoom, however, allows selection of
ranges beneath the surface so any
area of water between the surface
and the bottom can be enlarged to
provide more detailed information.
By using the full display to show a small
area of coverage, the effective display
resolution is increased, and the unit’s
ability to separate close targets is
enhanced.
Depth Range
There are four Zoom ranges available:
1
2
7 / ', 15', 30', and 60'. These ranges
Upper Zoom Limit
are not directly user controlled but are
instead dependent on the current
depth range. In shallow water, when
the 15' or 30' range is in use, the
1
2
Zoom range is 7 / '. If the 60' or 120'
range is in use, the Zoom range is 15',
if a 180'-480' depth range is in use,
the Zoom range is 30', and if the 600'
range is in use, the Zoom range is 60'.
16
Lower Zoom Limit
USING THE 105SX
MENU FUNCTIONS
The Zoom range is shown on the left side of
the screen and full range information is shown
on the right side of the display. Zoom can
either operate automatically, in which the
Zoom range is constantly adjusted to show the
bottom, or manually, in which the user controls
the location of the Zoom range.
Automatic Zoom is especially helpful when
looking for structure or bottom detail. The Automatic Zoom keeps the
bottom in view even in quickly changing terrain, but is most useful in
flatter areas without considerable depth variation. Manual Zoom provides
detailed information of any area from the surface to the bottom. In
manual Zoom, the Zoom range does not move as the terrain changes.
When the range is shown in the menu, the upper number represents the
top of the current Zoom range. The lower number represents the bottom
of the Zoom range. Use the UP and DOWN ARROW buttons to move this
range. The upper number can never be less than 0 (the surface of the
water), and the lower number can never be greater than the active depth
range. The difference between the two numbers (the Zoom range) is
preset and determined by the active depth range.
Once manual Zoom is selected, the display appears the same as in Auto
Zoom, but the zoom range does not change automatically.
To disable Zoom, press the MENU button until the Zoom menu is on-
screen. Use the UP ARROW to highlight Off, and let the menu time out.
When the unit is powered off, the Zoom menu returns to Zoom Off.
17
USING THE 105SX
MENU FUNCTIONS
Depth Alarm. The 105SX contains
an audible alarm to warn you of
shallow water depths. The alarm is
adjustable to depths of 3' to 99'
(30m). When the alarm is enabled,
an audible alarm sounds if the water
beneath the boat is equal to or less
than the selected alarm depth. The
alarm sounds continuously for about
five seconds, and then intermittently
to remind you that you are still in
shallow water.
Fish Alarm. The Fish Alarm alerts
you to the presence of fish, or other
targets not connected to the
bottom. The Fish Alarm has three
different settings that correspond to
the three different size fish symbols
shown on-screen.
The default setting is “OFF.” With
the “Large fish only” setting, the
105SX alarms on only those targets
that are represented by the large
fish symbols. The 105SX can be set
to alarm on only large and medium
fish, or set to alarm on all fish.
Set for large fish only
Once the Fish Alarm is
enabled, the 105SX emits an
audible beep when the
Set for large and medium fish
Set for all fish
selected size fish symbol appears on-screen.
18
USING THE 105SX
MENU FUNCTIONS
Bottom Black. There are two
selections available: Off and On. The
factory setting is Off. With this setting,
the 105SX displays the bottom using
Structure ID. This allows you to
determine the texture and relative
hardness of the bottom. Selecting
Bottom Black “ON” causes the unit to
blacken in the display below the
bottom. This gives the user easiest
recognition of the bottom location,
even from a great distance.
Bottom Black View
The 105SX remembers the Bottom
Black setting when powered off.
Fish ID. There are three selections
+
available: Off, ID ON, and Adjust. The
+
factory setting is ID On. With Fish ID
Off, sonar returns are displayed as
“raw” information. There is no inter-
pretation made by the unit. Selecting ID
Off also disables the fish alarm.
+
ID On enables the 105SX to interpret
the raw sonar data and, using a variety
of techniques, depict appropriate
target returns as one of three different
size fish symbols. The 105SX also
displays the depth beneath the surface
with the corresponding fish symbol.
Selecting Adjust and making
incremental changes enhances the
fishfinder’s ability to identify sonar
returns as fish symbols.
Increasing the value to a number
greater than zero shows more fish
19
USING THE 105SX
MENU FUNCTIONS
symbols on-screen. In this case
smaller sonar returns will be
depicted as fish symbols. This is
useful for identifying many smaller
sonar returns (such as baitfish) as
fish symbols.
+
Raw Sonar
ID On
Decreasing the value to a number
less than zero shows fewer fish
symbols on-screen. In this case
smaller sonar returns are
disregarded. This is useful for
eliminating many small sonar returns
when seeking larger species of fish.
The 105SX remembers this selection
even when the unit is powered off.
Triplog. Triplog provides a running
log of information based on input
from the Speed/Temp sensor.
Since Triplog requires
information from the Temp or
Speed/Temp sensors to operate,
if an accessory sensor is not
detected by the 105SX, the
Triplog menu will not appear as
a control menu.
Triplog provides seven pieces of
information: the current digital
depth, water surface temperature,
current boat speed, the distance
traveled since the 105SX was
powered up or reset, the average
speed, the total time elapsed since
power-up or reset, and the input
20
ADVANCED FEATURES
USING THE DIAGNOSTIC FEATURE
voltage from your boat’s electrical system.
The time, speed and distance calculations are useful for tracking your
progress on a trip. The input voltage is useful for determining the
condition of the charging system of the boat. When used in a portable
application or whenever the 105SX is operated from a battery source, the
voltage number can be used to determine battery life. The 105SX will
operate at voltages from 10 to 20 VDC. Voltages in excess of 20 or less
than 10 VDC cause the unit to power off.
USING THE DIAGNOSTIC FEATURE
The 105SX contains a powerful diagnostic tool that can aid in
determining the cause of a problem.
To use the Diagnostic feature, select
the Diagnostic feature on the start-up
menu on the initial screen.
Self Test. Initially, the 105SX will
perform a self-test. This test confirms
the operation of all internal circuitry.
At the conclusion of the test, one of
two messages will appear. “Passed”
indicates the internal test discovered
no failures, “Failed” indicates a
significant internal problem was
discovered and the unit requires
factory service. A code number
appears that tells repair personnel
where the problem is.
Transducer Connection. The first connection tested is Transducer input.
If a transducer is detected, the message “connected” appears. If a series
of dashed lines is shown, no transducer is connected or there is a
problem with the transducer or cable.
If you are using multiple transducers, switch between transducers to
confirm the connections for each.
Voltage Input. Another connection tested is the voltage input, and is
21
MAINTENANCE AND WARRANTY
MAINTENANCE
especially helpful in diagnosing input
voltage problems. The present input
voltage is displayed. If voltage
fluctuations or power supply in excess
of 20 VDC or less than 10 VDC is
suspected, use the diagnostic screen to
confirm input voltage. Often, small
outboard motors do not effectively
regulate voltage when operated at high
engine speeds.
Use Diagnostic while running the boat
at high speeds to show the voltage
gain. Also, if you are using the 105SX in
portable configuration or from the
trolling motor battery, Diagnostic can be
used to evaluate the health of the battery by showing the present
voltage. Voltage can also be viewed in the Trip Log view.
Total Time. The total time category indicates the total time the unit has
been in use since shipped from the factory. It is normal for some hours to
appear in the total time when the unit is new due to factory testing.
While this is often of interest to the user, it is primarily a diagnostic tool
for the repair technician should the unit need service.
MAINTENANCE
Your 105SX is designed to provide years of trouble free operation with
virtually no maintenance. Follow these simple procedures to ensure your
105SX continues to deliver top performance.
•If the unit comes into contact with salt spray, simply wipe the affected
surfaces with a cloth dampened in fresh water. Do not use a chemical
glass cleaner on the lens. Chemicals in the solution may cause cracking
in the lens of the unit.
•When cleaning the LCD protective lens, use a chamois and non-abrasive,
mild cleaner. Do not wipe while dirt or grease is on the lens. Be careful
to avoid scratching the lens.
22
MAINTENANCE AND WARRANTY
TROUBLESHOOTING
•If your boat remains in the water for long periods of time, algae and
other marine growth can reduce the effectiveness of the transducer.
Periodically clean the face of the transducer with liquid detergent.
Pivoting the transducer up in the bracket may allow better access for
inspection or cleaning.
•If your boat remains out of the water for a long period of time, it may
take some time to wet the transducer when returned to the water.
Small air bubbles can cling to the surface of the transducer and interfere
with proper operation. These bubbles dissipate with time, or you can
wipe the face of the transducer with your fingers after the transducer is
in the water.
•Never leave the 105SX in a closed car or trunk—the extremely high
temperatures generated in hot weather can damage the electronics.
TROUBLESHOOTING
Do not attempt to repair the 105SX yourself. There are no user
serviceable parts inside, and special tools and techniques are required for
reassembly to ensure the waterproof integrity of the housing. Repairs
should be performed only by authorized Humminbird technicians.
Many requests for repair received by Humminbird involve units that do
not actually need repair. These units are returned “no problem found.” If
you have a problem with your 105SX, use the following troubleshooting
guide before calling Customer Support or sending your unit in for repair.
The 105SX contains several tools that can aid in determining if there is a
problem and how to isolate and repair the problem in many cases.
1. Nothing happens when I turn the unit on.
Check the power cable connection at both ends. Be sure the cable is
connected correctly to a reliable power source—red lead to positive, black
lead to negative or ground. Ensure the power available at the mount is
between 10 and 20 VDC. If the unit is wired through a fuse panel,
ensure the panel is powered. Often accessory fuse panels are controlled
by a separate switch or the ignition switch. Also, often a fuse can appear
to be good when in fact is not. Check the fuse with a tester or replace it
with a fuse known to be good.
23
MAINTENANCE AND WARRANTY
TROUBLESHOOTING
Check the power connection to the 105SX. It is possible to force the
power cable connector into the cable holder incorrectly. If the connector
is reversed, the unit will not work. Examine the contacts on the back of
the unit to ensure there is no corrosion. Finally, ensure the unit is firmly
seated on the mount. The electrical contacts are not made until the unit
is fully seated.
Ensure the metal cable retainer is properly installed in the mount. If not,
the power connected may push out when the unit is put on the mount.
2. There is no transducer detected.
The 105SX has the ability to detect and identify that a transducer is
connected. If, at power up, a message indicates “transducer not connect-
ed,” only simulator operation is possible. First, ensure that an appropriate
transducer connector is positioned correctly in the connector holder, and
that the unit is fully seated on the mount. The 105SX will work with the
standard single beam transducer.
Second, inspect the transducer cable from end to end for breaks, kinks,
or cuts in the outer casing of the cable. Also ensure the transducer is fully
submerged in water. If the transducer is connected to the unit through a
switch, temporarily connect it directly to the unit and try again. If none of
these items identifies an obvious problem, the transducer itself is
probably the problem. Be sure to include the transducer if returning the
unit for repair.
3. There is no bottom reading visible on the display.
There are a number of possible causes for this condition. If the loss of
bottom information occurs only at high boat speeds, the transducer
needs adjusting. If the digital depth readout is working but there is no
bottom visible on-screen, it is possible the depth range has been adjusted
manually to a range lower than what is needed to display the bottom.
Also, in very deep water, it may be necessary to manually increase the
sensitivity setting to maintain a graphic depiction of the bottom.
If you are using a transducer switch to connect two transducers to the
105SX, ensure the switch is in the correct position to connect a
transducer that is in water. (If a trolling motor transducer is selected and
the trolling motor is out of water, no sonar information appears.)
If none of the above solve the problem, inspect the transducer cable from
end to end for breaks, kinks, or cuts in the outer casing of the cable. If
24
MAINTENANCE AND WARRANTY
TROUBLESHOOTING
the transducer is connected to the unit through a switch, temporarily
connect it directly to the unit and try again. If none of these items
identifies an obvious problem, the transducer itself may be the problem.
Be sure to include the transducer if returning the unit for repair.
4. When in very shallow water, I get gaps in the bottom reading
and inconsistent digital depth indication.
The 105SX will work reliably in water 3', or deeper. The depth is
measured from the transducer, not necessarily from the surface.
5. The unit comes on before I press POWER, and won’t turn off.
Check the transducer cable—if the outer jacket of the cable has been cut
and the cable is in contact with bare metal, you need to repair the cut
with electrical tape. If there is no problem with the cable, disconnect the
transducer from the unit and see if the problem is corrected, to confirm
the source of the problem.
6. I get gaps in the reading at high speeds.
Your transducer needs adjusting. If the transducer is transom-mounted,
there are two adjustments available to you—height, and running angle.
Make small adjustments and run the boat at high speeds to determine
the effect. It may take several tries to optimize high speed operation. This
can also be a result of air or turbulence in the transducer location caused
by rivets, ribs, etc.
7. My unit loses power at high speeds.
Your 105SX has over-voltage protection that turns the unit off when
input voltage exceeds 20 VDC. Some outboard motors do not effectively
regulate the power output of the engine’s alternator and can produce
voltage in excess of 20 volts when running at high RPMs. The 105SX
displays input voltage in the Diagnostic screen. Use this readout to
determine if the voltage exceeds 20 VDC.
8. The screen begins to fade out. Images are not as sharp as normal.
Check the input voltage using Diagnostic. The 105SX will not operate on
input voltages below 10 VDC.
9. The display shows many black dots at high speeds and high
sensitivity settings.
You are seeing noise or interference caused by one of several sources. Noise
25
MAINTENANCE AND WARRANTY
WARRANTY
can be caused by other electronic devices. Turn off any nearby electronics
and see if the problem goes away. Noise can also be caused by the engine.
If engine noise is causing the interference, the problem will intensify at
higher RPMs. Increase the engine speed with the boat stationary to isolate
this cause. Propeller cavitation can appear as noise on-screen. If the
transducer is mounted too close to the propeller, the turbulence generated
can interfere with the sonar signal. Ensure that the transducer is mounted
at least 15" (38cm) from the prop.
HUMMINBIRD ONE YEAR FULL WARRANTY
First year repairs (from original date of purchase) on your 105SX are
absolutely free. This does not include physical damage to the unit or its
accessory items. Any modification or attempt to repair the original
equipment or accessories by unauthorized individuals will void the
warranty. Return the warranty registration card and retain your bill of sale
for warranty verification. Accessories not manufactured under the
Humminbird trade name are not covered by our warranty. The customer
is responsible for shipping charges to Humminbird. Humminbird will
provide ground UPS or Parcel Post shipping back to the customer free of
charge. This warranty applies to the original purchaser only.
This warranty is in lieu of all other warranties expressed or implied and no
representatives or persons are authorized to provide for any other liability
in connection with the sale of our products. Humminbird reserves the
right to perform modifications or improvements on its products without
incurring the obligation to install the changes on units previously
manufactured, sold, delivered, or serviced.
THIS IS A FULL WARRANTY AS DEFINED BY THE FEDERAL WARRANTY
ACT, EFFECTIVE JULY 4, 1975.
26
MAINTENANCE AND WARRANTY
SERVICE POLICY
SERVICE POLICY
This Service Policy is valid in the United States only. This applies to
Humminbird units returned to our factory in Eufaula, Alabama, and is
subject to change without notice.
All repair work is performed by factory-trained technicians to meet
exacting factory specifications. Factory serviced units go through the
same rigorous testing and quality control inspection as new production
units.
Even though you’ll probably never need to take advantage of our
incredible service guarantee, it’s good to know that we back our units
this well. We do it because you deserve the best. We will make every
effort to repair your unit within three working days from the receipt of
your unit. This does not include shipping time to and from our factory.
Units received on Friday are usually shipped by Wednesday, units received
Monday are usually shipped by Thursday, etc.
We reserve the right to deem any product unserviceable when replace-
ment parts are no longer reasonably available or impossible to obtain.
After the original warranty period, a standard flat rate service charge will
be assessed for each repair (physical damage and missing parts are not
included). Please call our Customer Support Department to verify the
service charge for your unit.
If charges are not prepaid, the unit will be returned C.O.D.
If you are experiencing problems related to bottom or depth readings,
please send your transducer along with your unit when sending for repair.
27
MAINTENANCE AND WARRANTY
CUSTOMER RESOURCE CENTER
CUSTOMER RESOURCE CENTER
If you have any questions, call our Humminbird Customer Resource
Center Hotline:
1-334-687-0503
Throughout the U.S. and Canada, hours are Monday-Friday, 8:15 a.m. to
5:00 p.m. Central time.
troubleshooting guides.
If after reading “Troubleshooting” you determine your unit needs factory
service, please attach a description of the problem and send it with the
unit to the address below.
If you are including a check, please attach it to the unit.
Humminbird
Service Department
108 Maple Lane
Eufaula, AL 36027
Further information on Humminbird products can be found at:
28
MAINTENANCE AND WARRANTY
SPECIFICATIONS
Operating Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 kHz
Power Output . . . . . . . . . 2000 Watts (Peak to Peak) - 250 Watts (RMS)
Area of Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24° at -10 db
Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 20 VDC
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FSTN LCD
LCD Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 V x 64 H
Viewing Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.90" V x 2.35" H
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick Disconnect Mount
3
1
1
4
4
4
Unit Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 / "H x 6 / "W x 4 / "D
Transducer (Standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . XHS-6-24
Transducer Cable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20'
Depth Ranges . . . . . . 15', 30', 60', 120', 180', 240', 360', 480', & 600'
1
2
Zoom Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 / ', 15', 30', & 60'
29
Fiberglass
TOP
Remove and use for
Transducer Installation
Aluminum
Use ⁵⁄₃₂" drill bit & drill
two holes for hull type
Drill ●
Drill ●
Fiberglass
Fiberglass
Drill ■
Drill ■
Aluminum
Aluminum
TOP
U
s
e
5
/
3
2
"
d
r
i
l
l
b
i
t
Drill
Drill
DO NOT LET DEADRISE
INTERSECT THIS LINE
PLACE EITHER CORNER
ON DEADRISE ANGLE
Level
15", 40cm
TOP
Use 5/32" drill bit
from prop(s).
Drill
Drill
PLACE EITHER CORNER
ON DEADRISE ANGLE
PLACE EITHER ARROW
ON DEADRISE ANGLE
|