Envoy
CODE
100C
.
101C
OWNER'S HANDBOOK
(English Version)
FROM SERIAL NO: 100C001001, 101C001001
ISSUE 11.10.04
HANDBOOK: 100133(REV .0.)
CONTENTS
1.2 Main Features/Specifications
1.3 Contents
1.19 - 1.22 Mower Maintenance
1.19
1.19
1.19
1.19
1.19
1.20
1.21
1.21
1.22
- Deck Housing
- Securing Nuts and Bolts
- Lubrication
- Motor
- Switch Control Unit
- Cutterblade Removal
- Cutterblade Sharpening
- Supply Cable
1.4 Introduction
1.5 Warranty
1.6 - 1.9 Safety Precautions
- Storage
1.9 Safety Symbols
1.9 Control Symbols
1.23 - 1.24 Trouble Shooting
1.25 EC Declaration of Conformity
1.26 - 1.27 Parts List
1.10 Assembling the Mower
1.10
1.10
1.10
1.10
- Delivery Checklist
- Handlebar
- Grassbag Attachment
- Supply Cable
1.28 Parts list Diagram
1.30 - 1.31 Notes
1.11 - 1.15 Operating The Mower
1.11
1.11
1.11
1.11
1.12
1.12
1.12
1.13
1.13
1.13
1.13
1.14
1.15
- Electrical Connections
- Starting
- Forward Travel
- Turning
- Stopping
- Height of Cut
- Before Mowing
- Grassbag
- Without Grass Collection
- Heavy Growth
- Non-Grassed Areas
- Safe Mower Practice
- Overloading Protection
1.32 Customer Info
1.16 - 1.17
1.17
- Lawn Care Calendar - Guide Only
- Lawn Stripes
1.18 Maintenance Schedule
1.3
INTRODUCTION
Thank you for purchasing a Hayter mower. The following pages are designed to help you gain
safe and efficient service from your mower.
IMPORTANT: This ‘Owners Handbook’ should be regarded as part of the mower as it gives
essential information regarding mower safety, operation, maintenance and specifications. Read
and understand this handbook prior to operating your mower for the first time. Make sure you
are familiar with all the controls and points of regular maintenance. If you have any doubts,
consult your local Hayter authorised dealer who will be pleased to give you assistance.
IMPORTANT: This mower is designed solely for use in a domestic grass cutting
environment. Use in any other way is considered as contrary to the intended use. Compliance
with and strict adherence to the conditions of operation, service and repair as specified in this
handbook also constitute essential elements of the intended use.
This mower should be operated, serviced and repaired only by persons who are familiar with
its particular characteristics and who are acquainted with the relevant safety procedures.
The safety precautions listed in this handbook and all other generally recognised regulations on
safety must be observed at all times.
Any arbitrary modifications carried out to this machine may relieve Hayter Limited of
liability for any resulting damage or injury.
Hayter mowers are robustly constructed and designed for efficient economical
performance under normal mowing conditions. Correct operation and maintenance will ensure
a long and satisfactory service life. Prior to despatch from our factory every effort is made to
ensure that your mower is delivered in perfect condition.
Throughout this handbook all references to left and right are as viewed from behind the han-
dlebar, in the direction of forward travel.
This handbook is based on information available at the time of publication.
HAYTER LIMITED reserve the right to amend product specifications without prior notification.
1.4
WARRANTY
LIMITED WARRANTY
Hayter Limited warrants to the original user/purchaser that this unit shall be free from
defects in material or workmanship under normal use for a period of two years from the
date of purchase. To qualify for the full benefit of the warranty, the warranty registration
card must be returned to Hayter Limited within 14 days of purchase. If the selling dealer
has not returned the Warranty Registration Card which is attached to the rear of the Owners
Handbook please complete and return. Subject to the conditions and exclusions noted in
this limited warranty, we shall at our option, repair or replace any warranted part during the
applicable period. If you are in any doubt or experience any difficulty, please consult a
Hayter Authorised Service Dealer for clarification.
A 90 day warranty period applies to those items which are subject to normal wear and tear
e.g. wheels, cutterblades, cables, grassbags and other consumable wearing parts.
This warranty does not apply to any unit that has been tampered with, altered, misused,
abused or used for hire, and will become invalid if non genuine Hayter parts are fitted. This
warranty does not cover minor mechanical adjustments unless they are due to defective
material or workmanship. Consult the Owner's Handbook or a Hayter Authorised Service
Dealer for assistance when making these adjustments.
The machines are not warranted for commercial use.
To make a warranty claim, return the unit to a Hayter authorised service dealer along with
proof of purchase stating the machine serial number and date of purchase. Subject to the
conditions and exclusions in this limited warranty, the authorised dealer will, at our option,
repair or replace any warranted part within the duration of the warranty period.
This limited warranty gives specific legal rights and is in addition to any statutory rights to
which you may be entitled and your statutory rights are not affected by this warranty. If
you need additional information concerning this written warranty, or assistance in obtain-
ing services, please write to: Hayter Limited, Service Department, Spellbrook, Bishop's
Stortford, Hertfordshire, CM23 4BU
UK ONLY: Details of your local Hayter authorised dealer are contained in The Yellow
Pages or contact:- Freephone 0800 616298: or visit the Hayter website at
1.5
SAFETY PRECAUTIONS
Safety Alert Symbol
This safety alert symbol indicates important safety messages. When
you see this symbol be alert to the possibility of injury. Carefully read
the following and inform others.
Your mower is perfectly safe if used correctly. Failure to observe the
following precautions may result in serious injury.
Training
Read the instructions carefully. Ensure that you are familiar with the
controls and the proper use of the equipment. Learn how to stop the
mower quickly in an emergency.
Never allow children or people unfamiliar with these instructions to
use the mower.
Never mow while people, especially children, or pets are nearby.
Keep in mind that the user is responsible for accidents or hazards
occurring to other people or their property.
Preparation
It is recommended that a high sensitivity Residual Current - Operated
Circuit - Breaker (RCCB) with a trip current of not more than 30mA
is installed at the mains power socket. This will provide the user with
additional protection against electric shock. The fuse installed in the
plug only provides protection for the electrical equipment and will not
safeguard against electrocution. Always check the RCCB before using
the mower.
WARNING: Regularly inspect the supply cable for signs of damage
or ageing. Replace immediately if defective.
Always wear substantial footwear and long trousers while mowing. Do
not operate the equipment when barefoot or wearing sandals.
Thoroughly inspect the area where the mower is to be used and remove
all stones, sticks, wires, bones and other foreign objects.
1.6
SAFETY PRECAUTIONS
Preparation
Always ensure that the mower is in a safe operating condition.
Frequently check all nuts, bolts and screws for tightness. Use only gen-
uine Hayter parts.
A damaged cutterblade and loose fixing bolt are major hazards. Before
use, visually inspect the cutting mechanism to ensure that it is in good
condition. A damaged cutterblade must be replaced immediately with
a genuine Hayter replacement part. Cutterblades which are slightly
worn can be resharpened. Ensure that both cutting edges are resharp-
ened equally to maintain balance.
An unbalanced cutterblade may cause serious damage to your
machine.
Refer to "Maintenance."
Operation
SWITCH OFF AND REMOVE PLUG FROM MAINS.
- Before clearing blockages or unclogging the discharge chute.
- Before cleaning, checking or working on the mower.
- Whenever you leave the mower.
- After striking a foreign object. Inspect the mower for damage
and make repairs before re-starting and operating the mower.
- If the mower starts to vibrate abnormally (check immediately).
- If the supply cable is entangled.
THE CUTTERBLADE CAN CONTINUE TO ROTATE AFTER
THE MACHINE IS SWITCHED OFF.
Keep the supply cable clear of the cutterblade at all times.
Do not mow across the supply cable. Immediately disconnect the cable
from the mains supply if this occurs and check for damage. Do not use
a defective supply cable.
Mow only in the daylight or in good artificial light.
Avoid using the mower on wet grass, where feasible.
Always be sure of your footing on slopes.
Walk, never run.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on slopes.
Do not mow excessively steep slopes.
1.7
SAFETY PRECAUTIONS
Operation
Use extreme caution when reversing or pulling the mower towards you.
Switch off if the mower has to be tilted for transportation when cross-
ing surfaces other than grass and when transporting the mower to and
from the area to be mowed.
Never operate the mower unless the guards are securely in position and
in good condition.
Start the mower carefully, with feet well away from the cutterblade.
Do not tilt the front of the mower more than is absolutely necessary
when starting.
Never lift the rear of the mower.
Do not put hands or feet near or under rotating parts.
Never pick up or carry a mower while it is running or connected to the
mains supply.
Do not lift the rear deflector plate whilst the mower is in operation,
particularly when using without a grassbag.
Maintenance & Storage
Keep all nuts, bolts and screws tight to ensure that the mower is in a
safe working condition. (For torque settings refer to mower mainte-
nance).
Carefully examine the supply cable for signs of damage or ageing.
Replace immediately if defective.
Check the grassbag frequently for wear or deterioration and replace if
necessary.
Wear strong work gloves when removing and reassembling the cut-
terblade.
Replace worn or damaged parts for safety.
1.8
SAFETY PRECAUTIONS
Safety Symbols
Danger of being hit by thrown
objects.
Safety Alert - Be aware to the
possibility of injury.
Danger of severing toes or fin-
gers in cutting mechanism.
Carefully read the Owners
Handbook before using the
machine.
Switch off and remove plug
from mains before performing
maintenance or repair work.
Keep bystanders at a safe dis-
tance from the mower.
Do not use in rain or in wet
conditions.
Wait until all machine compo-
nents have stopped before
touching them.
STOP
Control Symbols
Switch ON / OFF
(Symbol)
Height of Cut Adjustment
(Symbol)
305113
1.9
ASSEMBLING THE MOWER
Delivery Checklist
Remove the mower from the packaging and check that the following
items have been supplied correctly. If any items are missing contact,
your local Hayter dealer.
1. Instruction Sheet 2. Grassbag Frame 3. Grassbag Top Cover
4. Grassbag Fabric 5. Supply Cable
To prevent accidents cut off the long ribbon attached to the grass-
bag and discard.
Handlebar
Unscrew the handlebar securing knobs sufficiently to allow the handle-
bar to pivot. Unfold the handlebar to the operating position. Tighten all
handlebar knobs to secure the handlebar in position.
Take care to ensure that the power cable does not become snagged at
the pivot points.
Grassbag Attachment
Once the grassbag is assembled. Raise the rear deflector, pass the
grassbag under the handlebar and hook in position. Lower the deflec-
tor to rest on the grassbag.
Supply Cable
Route the supply cable loosely across to the cable cleat on the left side
of the handlebar. Make a loop in the supply cable and secure to the
cable cleat.
1.10
OPERATING THE MOWER
Electrical Connection
Position the mower on the grass area to be cut. Carefully uncoil the
supply cable clear of the mower. Ensure that the mains socket is
switched 'OFF' before connecting. Switch 'ON'.
Note: We recomend the use of a RCCB unit- Refer to "Safety
Precautions" - Preparation.
Starting
Locate the bail arm lever mounted on the handlebar and ensure that
your feet are clear of the mower deck. Depress the safety button with
the right hand and pull the bail arm towards the handlebar with the left
hand. The motor will now start.
Forward Travel
Hold and push against the handlebar with both hands to move the
mower forwards.
Turning
To make a wide turn steer the mower with the handlebar whilst travel-
ling forward.
To make a tight turn apply downward pressure on the handlebar to
raise the front wheels of the mower just above ground level and steer
the mower using the handlebar in the required direction.
To prevent accidents do not raise the front of the mower exces-
sively when making a turn. Never raise the rear of the mower
when the motor is running.
1.11
OPERATING THE MOWER
Stopping
Release the bail arm to stop the motor.
WARNING: AVOID ACCIDENTS - The cutterblade may contin-
ue to rotate after the mower is switched off
Height of Cut
Move the height of cut lever sideways to disengage it from the locking
notch, then push forwards to lower or pull backwards to raise the height
of cut. Release the lever in the required position and ensure that it locks
firmly into one of the seven notch settings.
3 0 5 3
Always select a height of cut to suit operating conditions. Prevent
motor overloading and blockages by avoiding low cuts in long grass
conditions. Be prepared to make two cuts when the grass is long.
305113
Before Mowing
To prevent accidents thoroughly inspect the area and remove all
objects which when contacted by the mower cutterblade could
become dangerous projectiles. Inspect the area for hidden obstruc-
tions which when contacted by the cutterblade could risk health
and safety. Remember the location of these obstructions and
ensure that you mow around them.
1.12
OPERATING THE MOWER
Grassbag
To empty the grassbag raise the rear deflector and pass the grassbag
under the handlebar and lower the rear deflector to rest against the rear
of the mower.
Pour out the grass clippings and shake the grassbag vigorously to clean
the airways. Good grass collection depends on good air flow through
the grassbag. When collecting grass clippings it is important that the
grassbag is emptied regularly to prevent blockages and motor over-
loading.
Without Grass Collection
Remove the grassbag and operate the mower with the rear deflector in
the closed position.
Heavy Growth
Areas of heavy growth should be mown without collecting the clip-
pings. If collection is required, first mow the area without the grass-
bag at the maximum height of cut setting. Allow the grass clippings to
dry out and then mow the area at the maximum height of cut setting
with the grassbag fitted. Reduce the height of cut and mow the area
again as necessary until the required finish is obtained.
3 0 1 3
305113
To prevent grass damage do not remove more than one third of grass
height in one cut.
Non-Grassed Areas
When moving the mower across non-grassed areas, stop the motor and
set the mower to the maximum height of cut to protect the cutting
mechanism.
1.13
OPERATING THE MOWER
Safe Mower Practice
WARNING: PREVENT ACCIDENTS -Take extreme care do not
mow across the supply cable. If this should occur, switch off immedi-
ately and disconnect the plug from the power supply. Carefully exam-
ine the cable for cuts and damage. A defective cable must be replaced
before the mower is used again. Always be aware of the location of the
supply cable in relationship to the mower and the grass area. Do not
allow the cable to become hidden in uncut grass. Keep the cable over
the cut area at all times. A cable which is out of sight is out of mind
and this could lead to a hazardous situation. Plan a 'cutting scheme'
which works away from the power supply point and ensures that the
cable is trailed out over the cut area. Work up and down the lawn in
rows. Turn the machine round at the end of the row and step across the
cable so that the cable is trailed along in the cut area on the return run.
When working around flower beds, prevent the cable from trailing
across the cultivated area by positioning a stake at the corner of the
bed. Do not allow the cable to be pulled around sharp obstructions.
Stop mowing immediately if cable resistance is felt and remove the
obstruction. Do not allow the cable to become entangled.
WARNING: PREVENT ACCIDENTS - Switch off at the mains,
remove the plug before adjusting, cleaning or if the cable is entan-
gled.
1.14
OPERATING THE MOWER
Overloading Protection
Do not let the motor labour or slow down through being overloaded in
work. When this situation occurs, raise the front of the mower slightly
by bearing down on the handlebar, allow the motor to reach maximum
speed and proceed to mow at a slower pace. Alternatively readjust to a
higher cut position. If the motor continues to labour, switch off and
remove the plug from the mains supply. Remove and empty the grass-
bag. Examine the discharge chute and remove any blockage. Turn the
machine on its side and clear any obstruction from the cutterblade and
the underside of the mower deck. Place the machine upright and
replace the grassbag. Readjust to a higher cut position if necessary.
Restart the mower and proceed to mow at a pace which does not over-
load the mower.
IMPORTANT: PREVENT DAMAGE - DO NOT continue to
operate the motor in an overloaded condition. If this does occur,
stop mowing and allow the motor to run at maximum speed for
one minute. This will allow the motor to cool down to its normal
working temperature.
1.15
LAWN CARE CALENDAR
To be used as a guide only.
January
There is very little work to do this month apart from brushing away
leaves. Keep off the grass if frozen or waterlogged.
February
Rake the grass thoroughly. Spike the lawn to aerate and stimulate soil
organisms and root growth and apply lawn sand if necessary.
March
The yearly lawn work programme really starts this month. As soon as
the ground conditions are suitable, the first cut can be made. The first
cut should merely “top” the grass as close cutting at this stage could
result in severe yellowing or browning. Two cuts are generally suffi-
cient this month.
April
Mow often enough to stop grass growing away. Dig out patches of
coarse grass or resistant weed. Re-seed bare patches.
May
Keep mowing increasing the frequency as required. Treat with selec-
tive weed killers or combined weed/feed preparations if you did not
feed the lawn in April.
June
Summer mowing should now be under way. It should be necessary to
mow the lawn twice a week. Raking before mowing is important this
month as the combined action keeps runners of clover under control.
Water the grass if necessary, and remember to soak thoroughly.
July
Treat the grass with the second application of fertiliser or weed
killer/fertiliser. Water when necessary and rake occasionally. As a gen-
eral rule the grass clippings should be removed each time you mow. If
weather conditions are dry and hot and the grass is weed free, leave the
clippings on the lawn to help maintain ground moisture.
1.16
LAWN CARE CALENDAR
August
Keep mowing regularly and watering as necessary. Fill any cracks
caused by drought with a mixture of sharp sand and soil. In dry weath-
er conditions leave the grass longer to help retain ground moisture.
September
Raise the height of cut to allow the grass to thicken and protect the
roots from the winter frost and snow.
October
Rake out the thatch from the turf and spike the lawn to assist in
drainage. Brush in peat and sharp sand.
November
Use a stiff broom to disperse worm casts before mowing. Keep turf
free from leaves.
December
Apart from brushing away leaves, December is a slack end of a busy
year. Keep off the lawn if it is very wet or frozen.
Lawn Stripes
1
2
The way to achieve a neat striped effect is for the lawn being cut in
parallel stripes, alternate stripes being mown in opposite directions. A
much more important routine is to cut at right angles to the line of the
previous mowing. If the work has been carried in a north-south line,
then the next cutting should be in an east-west direction. The cross-
cutting keeps down the coarse weed grasses.
1CG480V05A
To prevent grass damage do not remove more than one third of the
grass height in one cut.
1.17
MAINTENANCE SCHEDULE
Follow the hourly or calendar intervals, whichever occurs first. More
frequent service will be required if working for prolonged periods
under dusty, dry conditions, or when airborne debris is present or after
extensive operation cutting tall, dry grass.
Daily
Remove grass debris from around the height of cut ratchet, air filter in the
cowl and the underside of the deck housing.
Remove grass debris from the grassbag and check for signs of damage.
Check the condition of guards and safety devices.
Check condition of cutterblade.
25-50Hrs or Every Season
Lubricate wheels, pivot points and linkages.
Sharpen the cutterblade.
Flash test (Dealer) to ensure complete safety.
Check cables/switch and connection
Replace air filter
1.18
MOWER MAINTENANCE
Deck Housing
Remove grass debris from the top and underside of the deck housing
immediately after use.
Securing Fasteners
Regularly check that all securing nuts and bolts are tight. Replace
missing or damaged items immediately.
Bolt - Cutterblade fixing Torque 20Nm
Plastic Screws - Bottom of Handlebar Torque 3.5Nm
General Screws - Used on plastic parts 1.5Nm (Note: Use manual
handtools only).
1CG480V36B
Lubrication
Lubricate the wheels, pivot points and linkages with engine oil every
25 operating hours.
Motor
The motor is maintenance free.
Switch Control Unit
The switch control unit is maintenance free.
1.19
MAINTENANCE
MOWER
Cutterblade Removal
Turn the mower on its side.
Firmly grip the end of the cutterblade (2) with a gloved hand and
remove bolt (1). When replacing ensure that the new cutterblade is the
2
correct way up with the turned edges facing towards the motor before
locating onto the two carrier pins. Secure the cutterblade fixing nylon
bolt and tighten to the specified torque of 20Nm.
1
The cutterblade has sharp edges. ALWAYS wear strong gloves to
protect your hands when working on the cutterblade. DO NOT
rotate tools towards the cutting edges to avoid the risk of injury
should the tool slip. ALWAYS use genuine Hayter replacement
parts.
The condition of the cutterblade and its mounting arrangement should
be checked regularly for signs of wear or damage. Ensure that the cut-
terblade is not bent or cracked.
A damaged cutterblade that is out of balance will vibrate excessively
and may break. DO NOT use an unbalanced cutterblade.
Regularly check that the bolt securing the cutterblade is tightened
to the specified torque of 20Nm.
Replace the cutterblade every 2 years or sooner if excessively worn or
damaged.
To prevent injury it is wise to seek assistance when turning the mower
on its side.
1.20
MOWER MAINTENANCE
Cutterblade Sharpening
A slightly worn cutterblade may be re-sharpened. Both blade edges
must be sharpened equally to ensure balance. Sharpen the cutterblade
every 25 mowing hours or more frequently if conditions require.
Remove the cutterblade from the mower and clean using a brush and
water. Inspect the cutterblade for signs of damage. Sharpen both cut-
ting edges with a flat file to restore performance.
30°-45°
Ensure that the cutterblade is balanced. Use a screw driver with a
round shaft to support the cutterblade through its centre hole. Hold the
cutterblade horizontal and then release. A balanced cutterblade will
remain horizontal.
If the cutterblade is not balanced the heavy end will rotate downwards.
Sharpen the heavy end until the cutterblade is correctly balanced.
Supply Cable
Check the condition of the supply cable for damage or ageing. Replace
immediately if defective.
1.21
MAINTENANCE
Storage
MOWER
Handlebar storage: To collapse the handlebar first unscrew the two
top securing knobs to allow the top section of the handlebar to pivot
forward to rest against the middle section then unscrew the bottom two
securing knobs sufficiently to allow both top and middle sections to be
folded forwards.
Storage for long periods: To ensure your mower is maintained in
good working order it is important that the following procedure is
adopted when the mower is stored for periods in excess of one month.
Refer to the Maintenance section as necessary.
Clean all areas of the mower and ensure that the grassbag is clean.
Lubricate the mower.
Treat metal parts with a water repellent anti-corrosion product.
Lower the handlebar if desired.
Cover the mower with a protective sheet and store it in a dry area.
Rest the mower deck on wooden blocks to remove the weight of the
mower from its wheels / roller.
1.22
TROUBLE SHOOTING
PROBLEM
POSSIBLE FAULT
REMEDY
Motor fails to start.
Mains supply socket dead.
RCCB tripped.
Test socket by plugging in anoth-
er appliance.
Remove mower plug and check
RCCB action. Check the supply
cable for any obvious signs of
damage and replace immediately
if defective. If no obvious faults
are found a serious fault is indi-
cated. Contact your Hayter
Dealer.
Plug pulled out of mains
socket.
Re-engage plug.
Fuse failure.
Fit a new 13 amp fuse.
Supply cable damaged.
Disconnect from the mains and
check the supply cable for any ob-
vious signs of damage. Replace
immediately if defective.
Cutterblade obstructed.
Disconnect from the mains and
remove any obstructions.
Motor will not stop.
Faulty switch control unit.
Ensure switch lever has returned
to the 'OFF' position. Disconnect
from the mains and contact your
Hayter Dealer.
Cutterblade runs on exces-
sively after switching
'OFF'.
Faulty brake unit.
Contact your Hayter Dealer.
1.23
TROUBLE SHOOTING
PROBLEM
POSSIBLE FAULT
Mounting bolts loose.
Cutterblade bolt loose.
Cutterblade out of balance.
REMEDY
Motor vibrates excessively.
Tighten bolts.
Tighten bolt.
Balance cutterblade.
Uneven cut
Undulating ground contours.
Cutterblade worn.
Change direction of travel.
Sharpen the cutterblade.
Balance cutterblade.
Cutterblade out of balance.
Wheels / Roller damaged.
Inspect and replace as necessary.
Discharge chute blocks.
Grass is wet.
Mow dry grass.
Cut height too low.
Grassbag full.
Increase cut height.
Empty grassbag.
Clean the grassbag.
No airflow through the
grassbag.
Mower is hard to push.
Poor grass collection.
Cut height too low.
Increase cut height.
Wheels / Roller damaged.
Inspect and lubricate or replace
as necessary.
No airflow through the
grassbag.
Clean the grassbag.
Discharge chute blocked.
Wet grass.
Remove blockage.
Mow dry grass.
Empty grassbag.
Grassbag full.
1.24
EC DECLARATION OF CONFORMITY
Manufactured for: HAYTER LIMITED,
Spellbrook, Bishop’s Stortford, Herts, CM23 4BU. ENGLAND
declare that the lawnmower:
Type.
Model name:
Model No:
Pedestrian Rotary Electric Lawnmower
Envoy
Code 100C/101C
360 mm
2950 rpm
Suzhou Taihu
2950 rpm
Cutting width:
Speed of rotation of cutting device:
Motor manufacturer:
Speed of rotation of motor:
Complies with the provisions of Directive: 98/37/EC Essential Health & Safety
Requirements relating to the Design & Construction of Machinery and Safety Components, as
amended and the regulations transposed into national law.
Also Directive 89/336/EEC Electromagnetic Compatibility, as amended and the regulations
transposed into national law.
Also Directive 73/23/EEC Low Voltage, as amended and the regulations transposed into
national law.
Also Directive 2000/14/EC Noise emission in the environment by equipment for use outdoors
and the regulations transposed into national law.
Procedure applied for the conformity assessment: ANNEX VI, procedure 1.
Notified Body: ITS Testing & Certification, Cleve Road, Leatherhead,
Surrey, KT22 7SB. ENGLAND.
Notified body identification No: 0359.
Measured sound power level:
Guaranteed sound power level:
88 dB(A)
96 dB(A)
Complies with harmonized standards: EN 292, EN 836, EN 55014 - 1, EN 55014 - 2,
EN 61000 -3 - 2 & EN 61000 - 3 - 3
Authorised Signature
Date: September 2004
Declaration done and Technical
Documentation Kept at:
HAYTER LIMITED,
Spellbrook, Bishop’s Stortford,
Herts CM23 4BU ENGLAND
Steve Maryniak
(Technical Director)
VIBRATION INFORMATION
Hand/arm vibration level measured to the procedure in European Standard EN 836
CODE 100C = 6.1 ms-2 CODE 101C = 6.1 ms-2
1.25
PARTS LIST
DESCRIPTION
ITEM NO.
PART NO.
QTY.
ITEM NOTE
1
2
3
4
5
6
7
8
Motor
Capacitor
Underdeck
Throw Plate
Wheel - Wide Assy
Bearing - Wheel
Hub - Cap
Starlock 12mm
Rod - Rear Axle
Wheel - Thin Assy
Lever - HOC
100001
100002
100003
100004
100506
100033
100036
100047
100068
100505
100038
100041
100504
100064
100078
100013
100012
100014
100037
100048
100503
100006
100076
100125
410087
100011
410064
100082
100010
100026
100025
100024
100515
100128
100017
100510
100512
100028
100007
100126
1
1
1
1
2
12
4
4
1
4
1
1
1
4
51
1
1
1
1
3
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Spring - HOC
Rear Axle Assy
Plate - Axle Pivot
Screw - M4
Bolt - Fixing Cutterblade
Cutterblade
Carrier - Cutterblade
Rod - Connecting
Starlock - 8mm
Axle - Front Assy
Fins - Front
Bolt - Motor
Cover - Main
Decal - Hayter
Filter
Decal - Grass Blade
Decal - Envoy
Cover - Air Vent
Handlebar - lower
Handlebar - Middle
Handlebar - Upper
Switch - Assy/ Trailing Lead
Screw - M4 x 19
Bail Arm
Mount - Bail Arm Assy
Hand Wheel - Assy
Bolt - Handlebar
Deflector - Rear
Rod - Deflector
1.26
PARTS LIST
DESCRIPTION
ITEM NO.
PART NO. QTY.
ITEM NOTE
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Spring - Deflector
Knob - HOC
Ratchet - HOC
Washer - Spring M8
Grassbag - Fabric/base
Frame - Grassbag
Top - Grass Bag
Screw - M6 x 20
Bolt - Plastic Handlebar
Fan - Motor Top
Spacer - Rear Wheel
Pin - Spring HOC
Spring - Counter Balance
Cleat - Cable
100009
100039
100040
100119
100513
100016
100075
100127
100029
100019
100030
100042
100080
100105
100077
100079
100502
100023
100106
100135
1
1
1
4
1
1
1
2
2
1
6
1
1
1
1
2
1
4
4
1
1
Terminal Block
Washer - Grip M10
Grassbag - Assy
Cable - Tie
Washer - M8
Main Lead - 17m UK Assy
Inc. 45,46 & 47
Main Lead - 17m European Assy 100136
1.27
PARTS LIST
35
33
36
58
15
34
15
15
32
37
54
15
58
60/61
38
38
37
58
31
37
38
38
47
30
39
37
42
48
29
26
41
15
40
28
27
43
24
45
46
57
25
56
49
50
55
15
1
3
2
20
59
4
44
19
23
15
15
51
5
15
10
6
15
6
15
11
6
15
53
8
5
7
52
6
7
51
18
8
51
10
20
6
51
13
6
12
6
17
14
15
16
21
14
51
15
14
15
6
6
14
19
20
22
10
10
9
15
6
8
6
7
7
15
15
8
15
1.28
NOTES
Notes:-
1.29
NOTES
Notes:-
1.30
NOTES
Notes:-
1.31
CUSTOMER
INFORMATION
Serial No:
Motor Type 220-240V~50Hz (100C/101C)
Date of Sale:-
Your Local Dealer:-
|