HP Hewlett Packard Network Card 3C509B TP User Manual

Etherlink IIIB ISA Network  
Interface Card (10BT)  
3C509B-TP  
Installation Guide  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
1 Connecting to a Netware 3.12 Server  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96  
• DOS and MS-Windows for Workgroups 3.11 media.  
• Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Power on the machine and allow it to boot to a DOS prompt.  
3 Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s  
website) and execute 3C5X9CFG.EXE.  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
5 If changes are required, save those changes and exit.  
6 Remove the 3com cards driver diskette and insert Netware client for DOS  
and MS-Windows disk 1.  
7 Execute INST_DOS.EXE and enter yes to accept the agreement if you are  
using a Vectra VL8, then go directly to step 8.  
If you are using a Vectra VL7 or VE7/VE8, complete the installation by  
following the steps below.  
A Specify the settings as listed below:  
C:\NWCLIENT  
Yes  
Yes  
C:\WINDOWS  
No  
3Com Fast Etherlink/Etherlink III Bus Master2.  
b Under the heading "Select the driver for your network board", insert  
the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\CLI-  
ENT." (If you have an HP preloaded HDD, set path to "C:\Masters\Lan-  
Drv\3C509\NWCLIENT\)  
c Press "Enter" to continue the installation.  
d When prompted, insert the corresponding disks to complete file  
transfer and driver installation.  
e When the install utility is finished, press <CRTL><ALT><DEL> to  
restart the machine.  
f
After Windows loads, open the "NETWORK" folder, double-click the  
"NETWORK SETUP" icon.  
g Select "Networks", and verify that "Novell Netware (Workstation Shell  
4.0 and above)" is listed under "Install Windows support for the  
following network only:" and click on "OK."  
8 Accept the default products by pressing enter, and then press “F10” to  
continue.  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
9 Select 16-bit LAN Drivers and hit the enter key.  
10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”  
and hit enter.  
11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the  
path to “A:\NWCLIENT\” and press enter.  
12 Select “3Com Etherlink III Parallel Tasking Family” and press enter.  
13 Accept the default settings, press “F10” to continue, and verify the  
following entries for the “Installation Configuration Summary”:  
YES  
C:\NOVELL\CLIENT32  
C:\WINDOWS  
16-bit LAN drivers  
3Com Etherlink III Parallel Tasking Family  
14 Press “F10” to save and continue.  
15 When prompted, insert the corresponding disks to complete file transfer  
and driver installation.  
16 When the install utility is finished, press <CRTL><ALT><DEL> to restart  
the machine.  
17 After windows loads, open the “NETWORK” folder, double-click the  
“NETWORK SETUP” icon.  
18 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0  
and above)” is listed under “Install Windows support for the following  
network only:” and click on “OK.”  
 
1 Connecting to a Netware 3.12 Server  
Windows for Workgroups  
 
1 Connecting to a Netware 3.12 Server  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
• Vectra VL8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97  
• Vectra VL7 Driver Name: Elnk.VXD Size: 30KB Date: 7/18/96  
• Vectra VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97  
• Windows 95 SR2 media.  
• Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.  
3 Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s  
website) and execute 3C5X9CFG.EXE.  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
 
1 Connecting to a Netware 3.12 Server  
Windows 95 SR2  
5 If changes are required, save those changes and exit.  
6 Remove the 3com cards driver diskette and restart the machine.  
7 After windows loads, click on “Start,” to “Settings” and over to “Control  
Panel.”  
8 Double click on “Network” and select “Add.”  
9 Choose to add an adapter, click on “Add” then on “Have Disk.”  
10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter.  
(If you have a Hewlett-Packard pre-loaded HDD, set the path statement  
to “C:MASTERS\LANDRV\3C509B\”)  
11 High light the adapter labeled “3Com Etherlink III ISA (3C509/3C509B) in  
ISA Mode” and press “OK.”  
12 At the “Network” dialogue box, click on the “Identification” folder.  
13 Enter your “Computer Name,” “Workgroup,” and “Computer  
Description.”  
(If you do not have a Computer name, Workgroup name and Computer  
description, contact your network administrator)  
14 Approve the “Basic Configuration Resources” by clicking on “OK.”  
15 When prompted, set the path to your Windows 95 SR2 files and click on  
“OK.”  
16 Click on “YES” to complete installation and restart the machine.  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
2 Connecting to a Netware 4.11 Server  
Windows for  
Workgroups  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96  
• DOS and MS-Windows for Workgroups 3.11 media.  
• Novell Netware server 4.11 that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
• Netware client for DOS and MS-Windows.  
Device Configuration  
• I/O Base Address  
300  
• Interrupt Request Level  
• Boot PROM  
10  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
Disabled  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Procedure  
1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Power on the machine and allow it to boot to a DOS prompt.  
3 Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s  
website) and execute 3C5X9CFG.EXE.  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
5 If changes are required, save those changes and exit.  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
6 Remove the 3COM cards driver diskette and insert Netware client for DOS  
and MS-Windows disk 1.  
If you are using a Vectra VL8, go straight to step 7.  
If you are using a VL7 or VE7/VE8, finish the installation by using the  
instructions below.  
a Execute INSTSTALL.EXE.  
b Specify the settings as listed below:  
• C:\NWCLIENT  
• Yes  
• Yes  
• C:\WINDOWS  
• No  
• 3Com Fast Etherlink/Etherlink III Bus Master for VE7/VE8, (or  
3COM Etherlink III Parallel Tasking Family for VL7, then highlight  
option 6 and then go to step e below).  
c Under the heading "Select the driver for your network board", insert  
the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\  
CLIENT." (If you have an HP preloaded HDD, set path to "C:\  
Masters\LanDrv\3C509\NWCLIENT\)  
d Press "Enter" to continue the installation.  
e When prompted, insert the corresponding disks to complete file  
transfer and driver installation.  
f
When the install utility is finished, press <CRTL><ALT><DEL> to  
restart the machine.  
g After Windows loads, open the "NETWORK" folder, double-click the  
"NETWORK SETUP" icon.  
h Select "Networks", and verify that "Novell Netware (Workstation Shell  
4.0 and above)" is listed under "Install Windows support for the follow-  
ing network only:" and click on "OK."  
7 Execute INST_DOS.EXE and enter yes to accept the agreement.  
8 Accept the default products by pressing enter, and then press “F10” to  
continue.  
9 Select 16-bit LAN Drivers and hit the enter key.  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”  
and hit enter.  
11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the  
path to “A:\NWCLIENT\” and press enter.  
12 Select “3Com Etherlink III Parallel Tasking Family” and press enter.  
13 Accept the default settings, press “F10” to continue, and verify the  
following entries for the “Installation Configuration Summary”:  
YES  
C:\NOVELL\CLIENT32  
C:\WINDOWS  
16-bit LAN drivers  
3Com Etherlink III Parallel Tasking Family  
14 Press “F10” to save and continue.  
15 When prompted, insert the corresponding disks to complete file transfer  
and driver installation.  
16 When the install utility is finished, press <CRTL><ALT><DEL> to restart  
the machine.  
17 After windows loads, open the “NETWORK” folder, double-click the  
“NETWORK SETUP” icon.  
18 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0  
and above)” is listed under “Install Windows support for the following  
network only:” and click on “OK.”  
 
2 Connecting to a Netware 4.11 Server  
Windows for Workgroups  
 
2 Connecting to a Netware 4.11 Server  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
Vectra VL8 and VE7/VE8 Driver Name : W95EL5X9.INF Size: 16KB  
Date: 6/11/97  
• Vectra VL7 Driver Name: Elnk.VXD Size: 30KB Date: 7/18/96  
• Windows 95 SR2 media.  
• Novell Netrware 4.11 server that supports Net BEUI, NWLink IPX/SPX,  
and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.  
3 Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s  
website) and execute 3C5X9CFG.EXE.  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
5 If changes are required, save those changes and exit.  
 
2 Connecting to a Netware 4.11 Server  
Windows 95 SR2  
6 Remove the 3com cards driver diskette and restart the machine.  
7 After windows loads, click on “Start,” to “Settings” and over to “Control  
Panel.”  
8 Double click on “Network” and select “Add.”  
9 Choose to add an adapter, click on “Add” then on “Have Disk.”  
10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter.  
(If you have a Hewlett-Packard pre-loaded HDD, set the path statement  
to “C:\MASTERS\LANDRV\3C509B\WIN95\”)  
11 High light the adapter labeled “3Com Etherlink III ISA (3C509/3C509B) in  
ISA Mode” and press “OK.”  
12 At the “Network” dialogue box, click on the “Identification” folder.  
13 Enter your “Computer Name,” “Workgroup,” and “Computer  
Description.”  
(If you do not have a Computer name, Workgroup name and Computer  
description, contact your network administrator)  
14 Approve the “Basic Configuration Resources” by clicking on “OK.”  
15 When prompted, set the path to your Windows 95 SR2 files and click on  
“OK.”  
16 Click on “YES” to complete installation and restart the machine.  
 
3 Connecting to a Windows NT Server 3.51  
Windows for Workgroups Ver. 3.11  
3 Connecting to a Windows NT Server 3.51  
Windows for  
Requirements  
Workgroups Ver. 3.11  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
Driver Name: Elnk3. SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Server 3.51 machine that supports Net BEUI,  
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
300h  
• Interrupt Request Level  
• Boot PROM  
10  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
Disabled  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network Cable Media to the 3COM 3C509B card.  
3 After booting to DOS, insert the 3COM’s drivers disk “Etherlink 3C509-B  
Ethernet ver. 5.0.”, and execute “A:\3C5X9CFG.EXE.”  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
5 If changes are required, save those changes and exit.  
6 Remove the 3COM Drivers diskette and reboot the machine.  
 
3 Connecting to a Windows NT Server 3.51  
Windows for Workgroups Ver. 3.11  
7 After windows loads, open the “NETWORK” Program Group, and double-  
click on “Network Setup.”  
8 Select the “Networks” button in the “Network Setup” dialog box.  
9 Click on the “Install Microsoft Windows Network:” option, and click “OK.”  
10 Click on the “Drivers” button from the “Network Setup” dialog box, and  
click on “Add Adapter”.  
11 Click “OK” to accept the default choice of “Unlisted or Updated Network  
Adapter.”  
12 Type the path “A:\WFW311” in the “Install Driver” dialog box, and then  
insert the 3COM 3C509 drivers disk into the floppy drive, and click “OK.”  
(If you have an HP preloaded HDD, set path to  
“C:Masters\LanDrv\3C509B\WFW311”)  
13 Select “3Com Etherlink III (3C5X9)” in the “Unlisted or Updated Network  
Adapter” dialog box, and click “OK.”  
14 Make sure that the “3Com Etherlink III (3C5X9) [NDIS2/NDIS3]” is  
selected in “Network Drivers.”  
15 Accept the applicable network protocols, and then click on “CLOSE.”  
• 3Com EtherLink III (3C5X9) (NDIS2/NDIS3 )  
• Microsoft NetBEUI  
• IPX/SPX Compatible Transport with NetBIOS  
(If you do not have the required information, contact your network ad-  
ministrator)  
16 At the “Network Setup” dialog box, click on “OK”.  
17 Specify your User Name, Workgroup, and Computer Name in “Microsoft  
Windows Network Names” dialog box, and click on “OK”. (The Drivers  
will now start to copy)  
18 Finish the network card installation by clicking on “OK” in the “Network  
Setup” message.  
19 To complete the installation, click on “Restart Computer” button in the  
“Windows Setup” dialog box.  
 
3 Connecting to a Windows NT Server 3.51  
Windows for Workgroups Ver. 3.11  
 
3 Connecting to a Windows NT Server 3.51  
Windows for Workgroups Ver. 3.11  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2.  
• 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0.  
• Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB  
Date: 6/11/97  
• Vectra VL7 Driver Name: Elnk.Vxd Size: 30.2KB Date: 7/18/96  
• Windows 95 media.  
• Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM drivers disk “Etherlink 3C509-B Ethernet  
Drivers Ver. 5.0.” and change to Drive A: , and execute “3C5X9CFG.EXE.”  
5 Select “Configure NIC,” and verify the resource settings listed above  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
under the heading “Device Configuration.”  
6 If changes are required, save those changes and exit.  
7 Remove the 3Com Software driver diskette and reboot the machine.  
8 Click on “Start” and point to “Settings”, then select the “Control Panel.”  
9 In the Control Panel group, double click on the “Network” icon .  
10 In the “Network” dialog box , click on the “Add” button .  
11 In the “Select Network Component Type” dialog box, highlight “Adapter”  
then click on “Add.”  
12 Click on “Have Disk” in the “Select Network adapters” dialog box.  
13 Insert the 3COM Software “Etherlink 3C509-B Ethernet Drivers Ver. 5.0”  
disk into the floppy drive.  
14 With the Path set to “A:\” in the “Install From Disk” dialog box click “OK”.  
(If you have an HP pre-loaded HDD, set the path statement to  
“C:\MASTERS\LANDRV\3C509B\”)  
15 Select the “3Com Etherlink III ISA (3C509/3C509B) in ISA mode” and  
click “OK.”  
16 Accept the default Network Protocols as seen below, and click on “OK.”  
(If you do not have the required information, contact your network  
administrator)  
• Client for NetWare Networks  
• 3Com EtherLink III ISA (3C509/3C509b)  
• IPX/SPX -compatible ProtocolNetBEUI  
17 In the configuration folder, click on “Add”, then click “Protocol” and hit  
enter.  
18 Under “Manufacturers:” high light “Microsoft”, and under “Network  
Protocols:” high light “TCP/IP” and hit enter.  
19 In the “Network” dialog box, click on the “Identification” folder and  
specify your Computer Name, Workgroup, and Computer Description  
and click on “OK.”  
(If you do not have the required information, contact your network  
administrator)  
20 When prompted, specify the path to your Windows 95 files. (If you have  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
an HP preloaded HDD, set the path to  
“C:\MASTERS\WIN95\SYSTEM\CABS\”)  
21 To complete the installation, select “Yes” to restart your computer.  
 
3 Connecting to a Windows NT Server 3.51  
Windows 95 SR2  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
Windows NT  
Workstation  
Version 3.51  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 3.51 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
Driver Name: Elnk3. SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Workstation 3.51 and Service Pack Media.  
• Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210h  
210h  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM Software “3C509-B Ethernet drivers disk  
ver 5.0.” and execute “A:\3C5X9CFG.EXE.”  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration.”  
6 If changes are required, save those changes and exit.  
If you are using a Vectra VL8 or VL7, go directly to step 7.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
If you are using a Vectra VE7/VE8, follow the instructions below to  
complete the installation.  
a If changes are required, save those changes and exit.  
b Remove the 3COM software driver diskette and reboot the machine.  
c After Windows loads, open the "Main" program group, double-click on  
"Control Panel" icon.  
d Double click on the "Network" icon and agree to install Windows NT  
Networking on your computer.  
e Insert the Windows NT Workstation CD.  
f
In "Windows NT Setup", enter the path to your NT files and click on  
"Continue." (If you have an HP preloaded HDD, set path to "C:\I386")  
g Click on "Do Not Detect" from the " Network Adapter Card Detection"  
dialog box, and click on "Continue" in the second "Network Adapter  
Card Detection" dialog box.  
h From the "Drop Down List", scroll down and select "<Other> Requires  
disk from manufacturer" then click on "Continue".  
i
j
Set the path to "A:\" in the "Insert Disk" dialog box, and then insert the  
3COM 3C509 drivers disk.  
Click "OK" at the "Install Driver" dialog box. (If you have an HP pre-  
loaded HDD, set path to "C:\Masters\LanDrv\3C509\)  
k Select "3Com Etherlink III (3C509) ISA Adapter" in the Select OEM  
Option dialog box, and click "OK".  
l
Click on the "OK" button in the "Bus Location" dialog box.  
m Choose the appropriate network protocols by clicking the check boxes  
in the "Windows NT Setup" dialog box and click on "Continue." (If you  
do not have the required information, contact your network  
administrator.)  
n Choose to install all applicable TCP/IP options and select "Continue."  
(If you do not have the required information, contact your network  
administrator.)  
o At the "Network Settings" dialog box, click on "OK."  
p Accept the default "NWLink IPX/SPX Protocol Configuration" and hit  
Enter.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
q At the "TCP/IP Configuration" screen, choose to use DHCP or enter  
your TCP information and click on "OK." (If you do not have the  
required information, contact your network administrator.)  
r At the "Domain/Workgroup Settings" dialog box, click on "OK" to ac-  
cept the default "Workgroup" as your workgroup name. (If you do not  
have the required information, contact your network administrator.)  
s To complete the installation, remove the floppy disk , and click on "Re-  
start Computer" button in the "Windows NT Workstation Networking  
Setup" dialog box.  
7 Remove the 3com software driver diskette and reboot the machine.  
8 After windows loads, open the “Main” program group, double-click on  
“Control Panel” icon.  
9 Double click on the “Network” icon and agree to install Windows NT  
Networking on your computer.  
10 Insert the Windows NT Workstation CD.  
11 In “Windows NT Setup”, enter the path to your NT files and click on  
“Continue.” (If you have an HP preloaded HDD, set path to “C:\I386”)  
12 Click on “Do Not Detect” from the “ Network Adapter Card Detection”  
dialog box, and click on “Continue” in the second “Network Adapter Card  
Detection” dialog box.  
13 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer” then click on “Continue“.  
14 Set the path to “A:\” in the “Insert Disk“ dialog box, and then insert the  
3COM 3C509 drivers disk.  
15 Click “OK” at the “Install Driver” dialog box.  
(If you have an HP preloaded HDD, set path to  
“C:Masters\LanDrv\3C509\)  
16 Select “3Com Etherlink III (3C509) ISA Adapter” in the “Select OEM  
Option” dialog box, and click “OK”.  
17 Click on the “OK” button in the “Bus Location” dialog box.  
18 Choose the appropriate network protocols by clicking the check boxes in  
the “Windows NT Setup” dialog box and click on “Continue.”  
(If you do not have the required information, contact your network  
administrator)  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation Version 3.51  
19 Choose to install all applicable TCP/IP options and select “Continue.”  
(If you do not have the required information, contact your network  
administrator)  
20 At the “Network Settings” dialog box, click on “OK.”  
21 Accept the default “NWLink IPX/SPX Protocol Configuration” and hit enter.  
22 At the “TCP/IP Configuration” screen, choose to use DHCP or enter your  
TCP information and click on “OK.”  
(If you do not have the required information, contact your network  
administrator)  
23 At the “Domain/Workgroup Settings” Dialog Box, click on “OK” to accept  
the default “Workgroup” as your workgroup name.  
(If you do not have the required information, contact your network  
administrator)  
24 To complete the installation, remove the floppy disk , and click on  
“Restart Computer” button in the “Windows NT Workstation Networking  
Setup” dialog box.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation 4.0  
Windows NT  
Requirements  
Workstation 4.0  
• HP Vectra with Windows NT Workstation 4.0 Service Pack 3.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0.  
Driver Name: Elnk3.SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Workstation 4.0 and service pack media.  
(If you have a Hewlett-Packard pre-loaded HDD, the media is located at  
“C:\I386”)  
• Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM Etherlink 3C509-B Ethernet card and  
drivers disk ver 5.0. and execute “A:\3C5X9CFG.EXE.”  
5 Select “CONFIGURE NIC”, and verify the resource settings listed above  
under the heading “Device Configuration.”  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation 4.0  
6 If changes are required, save those changes and exit.  
7 Remove the 3com cards driver diskette and reboot the machine.  
8 Power on the machine and allow it to boot to Windows NT Workstation 4.0.  
9 Log onto the machine with administrator privileges.  
(If you do not have the required information, contact your network  
administrator)  
10 Open the “Network Properties” window and agree to install “Windows NT  
Networking.”  
11 With “Wired to the Network” checked, click on “Next.”  
12 Click on the option to “Select from list” then on “Have Disk.”  
13 Insert the 3COM 3C509 drivers disk into the floppy drive.  
14 With the path set to “A:”, click “OK.”  
(If you have a Hewlett-Packard pre-loaded HDD, set the path statement  
to “C:\MASTERS\LANDRV\3C509B\”)  
15 Select “3Com Etherlink III (3C509) ISA Adapter” and click “OK.”  
16 With “3Com Etherlink III (3C509) ISA Adapter listed in the “Network  
Adapters:” window, click on “Next.”  
17 Accept the applicable network protocols and click on “Next.”  
(If you do not have the required information, contact your network  
administrator)  
18 At the “Network Services:” prompt, accept default settings and click on “Next.”  
19 Finish the network card installation by clicking on “Next.”  
20 Designate the path to your NT files and select “Continue.”  
(If you have a Hewlett-Packard pre-loaded HDD, set the path to “C:\I386”)  
21 Accept type as “ISA” and number as “0” and click on “OK.”  
22 If you intend on using DHCP, then click on “Yes” and skip the next step,  
otherwise click on “No.”  
(If you do not have the required information, contact your network  
administrator)  
23 Enter the required information, “IP Address”, “Subnet Mask”, “Default  
Gateway”, “DNS” and “WINS” information and click on “OK.”  
24 At the “Show Bindings for:” window, accept default entries and click “Next.”  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation 4.0  
25 When “Windows NT is now ready to start the network…” click on “Next.”  
26 Specify your Computer Name, Workgroup or Domain and click on “Next.”  
(If you do not have the required information, contact your network  
administrator)  
27 After “Network has been installed on this computer” click on “Finish.  
28 To complete the installation, select “Yes” to reboot your computer.  
 
3 Connecting to a Windows NT Server 3.51  
Windows NT Workstation 4.0  
 
4. Connecting to a Windows NT Server 4.0  
Windows for Workgroups Ver. 3.11  
4. Connecting to a Windows NT Server 4.0  
Windows for  
Workgroups  
Ver. 3.11  
Requirements  
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.  
Driver Name: Elnk3. SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI,  
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
• I/O Base Address  
300h  
• Interrupt Request Level  
• Boot PROM  
10  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
Disabled  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network Cable Media to the 3COM 3C509B card.  
3 After booting to DOS, insert the 3COM’s drivers disk “Etherlink 3C509-B  
Ethernet ver. 5.0.”, and execute “A:\3C5X9CFG.EXE.”  
4 Select “CONFIGURE NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
5 If changes are required, save those changes and exit.  
6 Remove the 3COM Drivers diskette and reboot the machine.  
 
4. Connecting to a Windows NT Server 4.0  
Windows for Workgroups Ver. 3.11  
7 After windows loads, open the “NETWORK” Program Group, and double-  
click on “Network Setup.”  
8 Select the “Networks” button in the “Network Setup” dialog box.  
9 Click on the “Install Microsoft Windows Network:” option, and click “OK.”  
10 Click on the “Drivers” button from the “Network Setup” dialog box, and  
click on “Add Adapter”.  
11 Click “OK” to accept the default choice of “Unlisted or Updated Network  
Adapter.”  
12 Type the path “A:\WFW311” in the “Install Driver” dialog box, and then  
insert the 3COM 3C509 drivers disk into the floppy drive, and click “OK.”  
(If you have an HP preloaded HDD, set path to  
“C:\Masters\LanDrv\3C509B\WFW311”)  
13 Select “3Com Etherlink III (3C5X9)” in the “Unlisted or Updated Network  
Adapter” dialog box, and click “OK.”  
14 Make sure that the “3Com Etherlink III (3C5X9) [NDIS2/NDIS3]” is  
selected in “Network Drivers.”  
15 Accept the applicable network protocols, and then click on “CLOSE.”  
• 3Com EtherLink III (3C5X9) (NDIS2/NDIS3 )  
• Microsoft NetBEUI  
• IPX/SPX Compatible Transport with NetBIOS  
(If you do not have the required information, contact your network ad-  
ministrator)  
16 At the “Network Setup” dialog box, click on “OK”.  
17 Specify your User Name, Workgroup, and Computer Name in “Microsoft  
Windows Network Names” dialog box, and click on “OK”.  
(The Drivers will now start to copy)  
18 Finish the network card installation by clicking on “OK” in the “Network  
Setup” message.  
19 To complete the installation, click on “Restart Computer” button in the  
“Windows Setup” dialog box  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
Windows 95 SR2  
Requirements  
• HP Vectra with Windows 95 SR2.  
• 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0.  
Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size:16KB  
Date: 6/11/97.  
• Vectra VL7 Driver Name: Elnk3.vxd Size: 30.2KB Date: 7/18/96.  
• DOS and MS-Windows for Workgroups 3.11 media.  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM drivers disk “Etherlink 3C509-B Ethernet  
Drivers Ver. 5.0.” and change to Drive A: , and execute “3C5X9CFG.EXE.”  
5 Select “Configure NIC,” and verify the resource settings listed above  
under the heading “Device Configuration.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
6 If changes are required, save those changes and exit.  
7 Remove the 3Com Software driver diskette and reboot the machine.  
8 Click on “Start” and point to “Settings”, then select the “Control Panel.”  
9 In the Control Panel group, double click on the “Network” icon .  
10 In the “Network” dialog box , click on the “Add” button .  
11 In the “Select Network Component Type” dialog box, highlight “Adapter”  
then click on “Add.”  
12 Click on “Have Disk” in the “Select Network adapters” dialog box.  
13 Insert the 3COM Software “Etherlink 3C509-B Ethernet Drivers Ver. 5.0”  
disk into the floppy drive.  
14 With the Path set to “A:\” in the “Install From Disk” dialog box click “OK”.  
(If you have an HP pre-loaded HDD, set the path statement to  
“C:\MASTERS\LANDRV\3C509B\”)  
15 Select the “3Com Etherlink III ISA (3C509/3C509B) in ISA mode” and click “OK.”  
16 Accept the default Network Protocols as seen below, and click on “OK.”  
(If you do not have the required information, contact your network  
administrator)  
Client for NetWare Networks  
3Com EtherLink III ISA (3C509/3C509b)  
IPX/SPX -compatible Protocol- NetBEUI  
17 In the configuration folder, click on “Add”, then click “Protocol” and hit enter.  
18 Under “Manufacturers:” high light “Microsoft”, and under “Network  
Protocols:” high light “TCP/IP” and hit enter.  
19 In the “Network” dialog box, click on the “Identification” folder and  
specify your Computer Name, Workgroup, and Computer Description  
and click on “OK.”  
(If you do not have the required information, contact your network  
administrator)  
20 Set the default configuration to the desired I/O (300) and hit enter.  
21 When prompted, specify the path to your Windows 95 files.  
(If you have an HP preloaded HDD, set the path to  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
“C:\MASTERS\WIN95\SYSTEM\CABS\”)  
22 To complete the installation, select “Yes” to restart your computer.  
 
4 Connecting to a Windows NT Server 4.0  
Windows 95 SR2  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
Windows NT  
Workstation  
Version 3.51  
Requirements  
• HP Vectra with Microsoft Windows NT Workstation 3.51 installed.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.Driver  
Name: Elnk3.SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Workstation 3.51 and Service Pack Media.  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210h  
210h  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Bps  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duple  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network cable media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM Software “3C509-B Ethernet drivers disk  
ver 5.0.” and execute “A:\3C5X9CFG.EXE.”  
5 Select “CONFIGURE NIC” and verify the resource settings listed above  
under the heading “Device Configuration.”  
6 If changes are required, save those changes and exit.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
7 Remove the 3com software driver diskette and reboot the machine.  
8 After windows loads, open the “Main” program group, double-click on  
“Control Panel” icon.  
9 Double click on the “Network” icon and agree to install Windows NT  
Networking on your computer.  
10 Insert the Windows NT Workstation CD.  
11 In “Windows NT Setup”, enter the path to your NT files and click on  
“Continue.” (If you have an HP preloaded HDD, set path to “C:\I386”)  
12 Click on “Do Not Detect” from the “ Network Adapter Card Detection”  
dialog box, and click on “Continue” in the second “Network Adapter Card  
Detection” dialog box.  
13 From the “Drop Down List”, scroll down and select “<Other> Requires  
disk from manufacturer” then click on “Continue“.  
14 Set the path to “A:\” in the “Insert Disk“ dialog box, and then insert the  
3COM 3C509 drivers disk.  
15 Click “OK” at the “Install Driver” dialog box.  
(If you have an HP preloaded HDD, set path to  
“C:Masters\LanDrv\3C509\)  
16 Select “3Com Etherlink III (3C509) ISA Adapter” in the “Select OEM  
Option” dialog box, and click “OK”.  
17 Click on the “OK” button in the “Bus Location” dialog box.  
18 Choose the appropriate network protocols by clicking the check boxes in  
the “Windows NT Setup” dialog box and click on “Continue.”  
(If you do not have the required information, contact your network  
administrator)  
19 Choose to install all applicable TCP/IP options and select “Continue.”  
(If you do not have the required information, contact your network  
administrator)  
20 At the “Network Settings” dialog box, click on “OK.”  
21 Accept the default “NWLink IPX/SPX Protocol Configuration” and hit  
enter.  
22 At the “TCP/IP Configuration” screen, choose to use DHCP or enter your  
TCP information and click on “OK.”  
(If you do not have the required information, contact your network  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
administrator)  
23 At the “Domain/Workgroup Settings” Dialog Box, click on “OK” to accept  
the default “Workgroup” as your workgroup name.  
(If you do not have the required information, contact your network  
administrator)  
24 To complete the installation, remove the floppy disk , and click on  
“Restart Computer” button in the “Windows NT Workstation Networking  
Setup” dialog box.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation Version 3.51  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation 4.0  
Windows NT  
Requirements  
Workstation 4.0  
• HP Vectra with Windows NT Workstation 4.0 Service Pack 3.  
• 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0.  
Driver Name: Elnk3.SYS Size: 27KB Date: 7/18/96  
• Microsoft Windows NT Workstation 4.0 and service pack media.  
(If you have a Hewlett-Packard pre-loaded HDD, the media is located at  
“C:\I386”)  
• Microsoft Windows NT Server 4.0 machine that supports Net BEUI, TCP/  
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.  
Device Configuration  
Vectra VL8  
Vectra VL7  
Vectra VE7/VE8  
I/O Base Address  
210  
210  
300  
Interrupt Request  
Level  
10  
10  
10  
• Boot PROM  
Disabled  
• Transceiver Type  
Auto Select  
Windows or OS/2 Client  
9600 Baud  
• Network Driver Optimization  
• Maximum Modem Speed  
• Plug and Play Compatibility  
• Full Duplex  
Disabled  
Disabled  
Procedure  
1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B  
adapter card into an ISA slot.  
2 Connect network media to the 3COM 3C509B card.  
3 Insert a DOS bootable diskette and power on the machine.  
4 After booting, insert the 3COM Etherlink 3C509-B Ethernet card and  
drivers disk ver 5.0. and execute “A:\3C5X9CFG.EXE.”  
5 Select “CONFIGURE NIC”, and verify the resource settings listed above  
under the heading “Device Configuration.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation 4.0  
6 If changes are required, save those changes and exit.  
7 Remove the 3com cards driver diskette and reboot the machine.  
8 Power on the machine and allow it to boot to Windows NT Workstation 4.0.  
9 Log onto the machine with administrator privileges.  
(If you do not have the required information, contact your network  
administrator)  
10 Open the “Network Properties” window and agree to install “Windows NT  
Networking.”  
11 With “Wired to the Network” checked, click on “Next.”  
12 Click on the option to “Select from list” then on “Have Disk.”  
13 Insert the 3COM 3C509 drivers disk into the floppy drive.  
14 With the path set to “A:”, click “OK.”  
(If you have a Hewlett-Packard pre-loaded HDD, set the path statement  
to “C:\MASTERS\LANDRV\3C509B\”)  
15 Select “3Com Etherlink III (3C509) ISA Adapter” and click “OK.”  
16 With “3Com Etherlink III (3C509) ISA Adapter listed in the “Network  
Adapters:” window, click on “Next.”  
17 Accept the applicable network protocols and click on “Next.”  
(If you do not have the required information, contact your network  
administrator)  
18 At the “Network Services:” prompt, accept default settings and click on “Next.”  
19 Finish the network card installation by clicking on “Next.”  
20 Designate the path to your NT files and select “Continue.”  
(If you have a Hewlett-Packard pre-loaded HDD, set the path to “C:\I386”)  
21 Accept type as “ISA” and number as “0” and click on “OK.”  
22 If you intend on using DHCP, then click on “Yes” and skip the next step,  
otherwise click on “No.”  
(If you do not have the required information, contact your network  
administrator)  
23 Enter the required information, “IP Address”, “Subnet Mask”, “Default  
Gateway”, “DNS” and “WINS” information and click on “OK.”  
24 At the “Show Bindings for:” window, accept default entries and click “Next.”  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation 4.0  
25 When “Windows NT is now ready to start the network…” click on “Next.”  
26 Specify your Computer Name, Workgroup or Domain and click on “Next.”  
(If you do not have the required information, contact your network  
administrator)  
27 After “Network has been installed on this computer” click on “Finish.  
28 To complete the installation, select “Yes” to reboot your computer.  
 
4 Connecting to a Windows NT Server 4.0  
Windows NT Workstation 4.0  
 
 
Version Number 3Com 3c509 Rev.1  
 

Greenway Home Products Cooktop MES31BL User Manual
Gyration Mouse Compact Keyboard User Manual
HannsG Computer Monitor HG171AB User Manual
HANNspree Flat Panel Television ST09 10H1 User Manual
Heath Zenith Home Safety Product SL 4190 Series User Manual
Honeywell Air Cleaner F111 User Manual
Honeywell Cell Phone 9700 MSCR User Manual
HP Hewlett Packard Personal Computer C5J37AWABA User Manual
Hubbell Work Light UE28 User Manual
IFB Appliances Microwave Oven WT DIV B User Manual