Model IR412
LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. The liability of EURO-PRO
Operating LLC is limited solely to the repair or replacement of the product at EURO-PRO’s option.
This warranty does not cover damage caused by misuse, negligence, use on improper current or
voltage, use contrary to operating instructions or disassembly, repair or alteration by any person
other than EURO-PRO Operating LLC.
OWNER’S MANUAL
Retractable Cord Iron
Model IR412
Product repair or replacement, at our option, is your sole remedy. This warranty excludes all other
legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC, if any, is
limited to the specific obligations expressly assumed by it under the terms of the limited warranty.
In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any
nature whatsoever. Some States do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you. This warranty gives you specific
legal rights which vary from state to state.
1400 Watts
If you have a claim under this warranty or if you require service
DO NOT RETURN THIS PRODUCT TO THE STORE!
Send the product , postage prepaid to:
In U.S.A.: EURO-PRO Operating LLC
21 Lawrence Paquette Ind. Dr.
Champlain, NY 12919
Tel: (800) 798-7398
Please include a copy of your sales receipt, $9.50 to over the cost of return shipping &
handling and a letter explaining the nature of your difficulty. Do not forget to enclose your
name, address and telephone number.
If the warranty period has expired, please send your iron postage pre-paid to:
In U.S.A.: Service Department
EURO-PRO Operating LLC
21 Lawrence Paquette Ind. Dr.
Champlain, NY 12919
Tel: (800) 798-7398
You will be advised of the cost of repair before any servicing is done unless you enclose a
note indicating that you would like us to proceed with the repairs and return the iron to you
C.O.D.
PRODUCT REGISTRATION CARD
Please complete and return within ten (10) days of purchase. The registration will enable us to
contact you in the event a product defect is discovered. By returning this card you acknowledge
to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 21 Lawrence Paquette Ind. Dr., Champlain, N.Y. 12919
PURCHASER: ……………………………………………………………………………………………
ADDRESS: ……………………………………………………………………………………………….
For information or assistance:
USA: EURO-PRO Operating LLC
21 Lawrence Paquette Industrial Drive
Champlain, NY 12919
Model IR412
DATE OF PURCHASE: …………………….. MODEL: ………………. SERIAL NO: .…………….
NAME AND ADDRESS OF STORE: …………………………………………………………………..
Tel.: 1-800-798-7398
Printed in China
IRONING CHART
ADDITIONAL IMPORTANT SAFEGUARDS
1. Do not rest iron on soleplate.
9. CAUTION: Never use scouring
NOTE: Before starting to iron delicate
To select iron temperature, align
temperature selected on dial with
the indicator on the water tank.
pads, abrasive or chemical
cleaners, or solvents to clean the
exterior or soleplate of your iron.
Doing so will scratch and/or
damage the surface.
2. Never use or rest iron on an
unstable surface.
fabrics, it is best to first test the
temperature of the iron on a hem or an
inside seam.
3. While the iron is hot, never set iron
on an unprotected surface - even if it
is on its heel rest.
10.WARNING! DO NOT aim iron at
face, towards yourself, or anyone
else while using or adjusting
steam. Burns or serious injury
may occur.
11.Never store your iron face down,
even the smallest amount of
moisture will cause the soleplate to
corrode and stain.
4. WARNING! TO PREVENT
ELECTRIC SHOCK OR OTHER
INJURY, before filling the iron
with water, make sure that the
plug is removed from the outlet.
DIRECTIONS
ON LABEL
5. CAUTION: Never fill the iron with
fabric conditioner, starches or any
other solution, as these will
SYNTHETIC
FIBERS, e.g.
acrylic, nylon
polyester
SILK
COTTON
LINEN
FABRIC
damage the steam mechanism. Do
not use contaminated water.
WOOL
12.DANGER! Never use the iron if it
is damaged or dropped. Using the
iron when it is damaged could
create the risks of fire, electric
shock, injury or death.
6. WARNING! TO AVOID FIRE, never
leave iron unattended while it is
plugged in.
TEMP.
MIN
MAX
7. WARNING! TO PREVENT
ELECTRIC SHOCK, never
immerse the iron in water or other
liquid.
CONTROL
• • • • •
•
8. WARNING! TO PREVENT
ELECTRIC SHOCK, never use the
iron in a location where it can fall
or be pulled into water or any
other liquid. If the iron falls into
water or any other liquid, unplug it
immediately. DO NOT reach into
the water or liquid.
MINIMUM
STEAM
MAXIMUM
STEAM
STEAM
CONTROL
0
BURST OF
STEAM
SPRAY
9
2
GETTING TO KNOW YOUR RETRACTABLE CORD IRON
OPERATING INSTRUCTIONS (CONT.)
Before using your EURO-PRO Select
Retractable Cord Iron, remove any
labels, stickers or tags that may be
attached to the body or soleplate of the
iron.
When turned on for the first time, your
new iron may emit an odor for up to 10
minutes. This is due to the initial
heating of the materials used in making
the iron.
The odor is safe and should not reoccur
after initial heating.
SELF CLEANING
STORAGE
It is important to “Self Clean” the iron at
least every two weeks to remove scale,
calcium, etc. The harder the water, the
more often the iron should be self
cleaned.
1. Always turn the variable steam
control to “No steam position” after
you have emptied the water tank.
Also, before ironing with steam for the
first time, allow iron to heat, hold in a
horizontal position and hit the burst of
steam button several times. The iron
may emit some small particles from the
steam holes. This is normal and will
clear after pressing the burst of steam
button several times.
2. Stand the iron in the vertical
position to cool down before storing.
1. Set the variable steam control to
position “No steam position”.
3. Always store the iron in the upright
position to protect the soleplate.
2. Fill the water tank up to the “MAX”
level.
4. From time to time, clean the exterior
of the iron with a damp cloth and
wipe dry.
3. Stand the iron in the vertical position.
Plug the iron into the electrical outlet
and wait until the iron heats up and
thermostat light goes off and then
comes on again.
5. If you use spray starch, wipe the
soleplate occasionally with a soft
damp cloth to prevent the build-up of
deposits.
4. Hold the iron horizontally over the
sink and slide the variable
6. If the iron has not been used for a
few weeks, hold the iron horizontally
and allow to steam for 2 minutes
before ironing.
steam control lever to the “Self
Clean” zone. “
See Figure 6.
“
NOTE: The anti drip function reduces
water dripping and water stains. It does
not prevent water dripping and water
stains if you press the steam burst
button too often or if the temperature is
too low. The amount of water droplets
will eventually decrease after the iron is
used for 2 to 3 tankfuls of steaming and
ironing.
6. Boiling water and steam will now be
ejected from the holes in the
soleplate. The impurities and scale
are washed away with it.
1. Spray Nozzle
2. Water Filling Inlet
3. Variable Steam Control
4. Burst of Steam Button
5. Spray Button
6. Thermostat Light
7. Cord Winder
8. Temperature Control Dial
9. Transparent Water Tank
10.Soleplate
11.Cord Rewind Button
12.Power Cord
See Figure 7.
7. Move the iron back and forth as this
happens.
8. Slide the variable steam control lever
to the “No steam position” position
after one minute or when the water
tank is empty.
9. Place the iron back in the vertical
position to cool down before storing.
13.Water Flask
Figure 7
Technical Specifications
CAUTION: Hold the plug when
rewinding the cord. Do not allow
the cord to whip when rewinding.
Voltage:
Power:
120V., 60Hz.
1400 watts
Figure 6
3
8
OPERATING INSTRUCTIONS (CONT.)
FEATURES OF EURO-PRO SELECT RETRACTABLE
CORD IRON
SELECTING IRON
EMPTYING THE IRON
TEMPERATURES
1. Always empty iron after each use.
Always read garment labels and follow
the manufacturer’s ironing instructions.
Refer to the “Ironing Chart” on page 11
for temperature recommendations:
2. When finished using the iron, turn
the variable steam control to “No
steam position” and the temperature
control dial to “MIN”.
•
Use low settings for synthetics.
3. Unplug the iron from the electrical
outlet.
4
•• Use moderate settings for wool,
silks, and blends.
4. Set variable steam control to “MAX”.
••• Use high settings for cottons and
linens.
5. Turn the iron upside down over the
sink with the tip pointing downward
and allow the water to flow from the
opening.
IRONING HINTS
6. Set variable steam control to “No
steam position”.
WARNING! To prevent fire, do not
leave iron unattended while
connected.
7. Stand the iron in the vertical
position to cool down before storing.
•
Sort articles to be ironed according
to the type of fabric. This will reduce
the need to adjust the temperature
for different types of garments.
5. WATER FILLING INLET
The cover prevents dust and
foreign matter from entering the
water tank. It also stops any water
from spilling during ironing.
1. BLAST OF STEAM BUTTON
Pressing this Button provides a
powerful blast of steam without
dripping water.
WARNING! Use caution when
emptying the iron. Burns may occur
from touching hot metal surfaces,
hot water or steam.
•
If you are not sure of the fiber
content of a garment, test a small
area such as a seam or inside hem
section before ironing a visible area.
Start with a low temperature setting
and gradually increase to find the
best setting.
2. ATOMIZER SPRAY
BUTTON
6. RETRACTABLE CORD
Cord retracts quickly into a
convenient base.
ELECTRONIC AUTOMATIC
SHUT-OFF
Pressing this Button provides a
defined jet of spray which gently
moistens fabric.
Your Retractable Cord Iron is equipped
with an electronic auto shut-off. The
CAUTION: Hold the plug when
rewinding the cord. Do not allow
the cord to whip when rewinding.
electronic auto-off switches the iron off if it
has been standing in the vertical position
unmoved for approximately 8 minutes. A
red light will flash when the iron switches
itself off. To switch the iron back on, just
shake the iron side-to-side several times.
•
•
When reducing the temperature to
iron sensitive fabrics, allow
approximately 2 minutes for the iron
to cool to the new temperature
setting.
3. ADJUSTABLE STEAM
CONTROL
For selecting dry ironing, slide lever
down. For steam ironing, gradually
slide lever up to increase the
amount of steam.
7. ELECTRONIC AUTOMATIC
SHUT-OFF
Fabrics such as velour, wool, linen
and silk are best ironed with an
ironing cloth to prevent shine marks.
Your Retractable Cord Iron is
equipped with an electronic auto
shut-off. The electronic auto-off
switches the iron off if it has been
standing in the vertical position
unmoved for approximately 8
minutes.
WARNING! Never rely on the auto
shut-off to turn your iron OFF.
Never leave the iron plugged in and
unattended for any length of time.
4. TEMPERATURE DIAL
Turn dial to select
temperature. Main
temperature settings are
indicated by the 1, 2 and 3
dots. (See “Ironing Chart.”)
WARNING! Never rely on the auto
shut-off to turn your iron OFF.
Never leave the iron plugged in and
unattended for any length of time.
7
4
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (CONT.)
This appliance is for HOUSEHOLD USE
4. Turn the temperature dial to any of
WARNING! Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
2. Set the temperature dial to the
"MAX" position. Place the iron on a
stable surface and allow it to heat for
approximately 2 minutes.
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
the temperatures within the gray
steam band and allow the iron to
heat for approximately 2 minutes
before ironing. Place iron on a
stable, protected surface while the
iron is warming to the desired
temperature.
3. With the iron in a horizontal position,
press the burst of steam button
several times to prime the pump.
See Figure 4.
DRY IRONING
WARNING! TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
All marked settings on the temperature
dial can be used for dry ironing. Slide
the variable steam control lever all the
down as shown in Figure 1. This will cut
off the steam flow if water is in the tank.
5. Slide the steam lever up to increase
the amount of steam. When using
extra steam, the iron uses more
water and it may be necessary to fill
the tank more often. See Figure 3.
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
For Dry Ironing:
For Steam Ironing:
CAUTION: Never fill the iron with
fabric conditioner, starches or any
other liquid, as these will damage the
steam mechanism. Do not use
contaminated water.
Figure 4
NOTE: If the tank runs dry, remove the
plug from wall outlet. Then, fill the iron
with water and re-prime the pump. The
iron may be filled with water while it is
hot.
1. Turn temperature dial to “MIN” and
slide lever all the way down.
WATER SPRAY
Figure 1
1. Turn temperature dial to “MIN” and
slide the variable steam control lever
all the way down to "0" mark.
2. Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. See figure 2. Fill tank to
desired level or to the “MAX” water
level marking using the water filling
flask. (When the iron is upright, the
transparent water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank.
The water spray is useful on fabrics with
stubborn wrinkles. Press the spray
button and a jet of water will spray onto
the fabric being ironed. See Figure 5.
The water spray can be used with dry or
steam ironing as desired.
Figure 3
BURST OF STEAM
2. Plug the cord into a polarized, 120V
AC electrical outlet. The power “ON”
light will come on, indicating that the
iron is receiving power.
WARNING! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
3. Turn the temperature dial to the
desired setting. (See “Ironing Guide”
for a guide to temperature selection.)
The burst-of-steam button is useful
when ironing denim, cotton, and linens.
It provides extra, sudden blasts of
steam which aid in removing stubborn
wrinkles.
4. Place iron vertically on a stable,
protected surface while iron is
warming to desired temperature.
The burst-of-steam feature can be used
with Dry or Steam ironing as desired.
STEAM IRONING
Figure 5
WARNING! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
1. Make sure the water tank is at least
1/2 filled with water.
Figure 2
3. Plug the cord into a polarized, 120V
AC electrical outlet.
5
6
|