PRIMERGY RXI300
System configurator and order-information guide
February 2008
Contents
Instructions
Configuration diagram
Configurator
0
I
Software Configurator
Basic unit
II Processor
III Memory
IV Hard disk drives
V
SCSI / Fibre Channel Controller
VI Disk Array
VII Communication / Network
VIII System Management Products
IX Country specific power cord
Change Report
PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300
Status 2008-01-29
Configuration diagram PRIMERGY RXI300
TOP View
Basic unit ( I )
Memory ( III )
Extension slots
Disk Array / Fibre Channel ( V )
Communication/Network ( VI )
Processor ( II )
Itanium2
# 1
Itanium2
# 2
PCI Riser with 3 slots
PCI-X 64-Bit / 100MHz, 3.3V, long
PCI-X 64-Bit / 100MHz, 3.3V, long
PCI-X 64-Bit / 133MHz, 3.3V, long
1
1
0
1
2
3
FRONT VIEW
Hard disk drives, hot-plug ( IV )
Accessible drives
5,25"x 0,5"DVD-ROM
Operating Panel
3.5"x1"
3.5"x1"
SCSI-ID 0
SCSI-ID 1
Power supply
3. PSU
2. PSU
1. PSU
Key:
Included in basic unit
Option
Fujitsu Siemens Computers
Enterprise Products PRIMERGY Server
3 of 10
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
Start "PRIMERGY RXI300"
SW Configurator
with OEM-Software
for PRIMERGY Server
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
Microsoft - Software: W **)
Linux - Software: **)
- Windows Server 2003 R2,
Enterprise x64 Edition
- Additional loose
- SuSE Linux ES (OEM): LO
- SuSE Linux ES (Support): LS
- Red Hat EL (OEM): LO
Client-Access-Lizenzen (CALs)
- Red Hat EL (Support): LS
**) Pay attention to release and order information in PRINCE -> Operating System
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for partners:
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers
4 of 10
Enterprise Products - PRIMERGY Server
System Configurator and Order-Information Guide
Start PRIMERGY RXI300
PRIMERGY RXI300
Status 2008-01-29
Section
Basic unit
I
PRIMERGY RXI300
Basic Unit including:
2U Chassis with
Rack unit 2U
- 3 bays for 350W hot-plug power supply moduls,
2 hot plug moduls installed, 3rd modul req. for redundancy
(PSU redundancy restricted to 240V operation),
2 sep. AC inlets
Basic unit with:
- 1x Itanium 2 processor (max 2)
- 2xSCSI HD drive bays with hot swap backplane
- Fan unit with 6x60mm hot swap, variable speed fans
- I/O Riser board with 3 PCI-X slots
2xPCI-X long with 100MHz
4 GB main memory
1.6GHz / 3MB TLC
(Madison)
S26361-K963-V210
S26361-K963-V944
9015 (1.4GHz/12MB TLC) (Montecito)
1xPCI-X long with 133MHz
- 1x IDE CDROM/DVD-ROM Combodrive
- Front panel board and front bezel
* Rack- mounting kit (sliding rail´s)
- telescopic rails kit
- cable management arm
* Systemboard with
- 2 Itanium CPU sockets
S26113-F602-E350
one CPU installed according to the configurator
thermal blank in other socket if 2nd CPU not installed
- 2 memory banks with 4 DIMM memory slots each
for up to 16GB PC2100 registered DDR RAM with ECC
one bank installed according to the configurator
3rd power supply module (PSU)
for 2+1 redundancy (350W)
max. 1x per system
- onboard dual channel Ultra 320 SCSI
first ch.for int. Drives (SCSI backplane), RAID 1 support
second ch. for ext. SCSI devices
- dual port LAN-Controller 10/100/1000TX
- VGA Controller (8MB RAM) on-board (ATI Rage XL)
- External Interfaces:
PRIMERGY PRIMECENTER- Rack
1x RS-232 (serial, RJ45 connector) in back
2x VGA ports, 1 in front, 1 in back
"Rack-mounting ex factory"
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
server/storage subsystem
4x USB 1.1, 2 in front, 2 in back
2x LAN 10/100/1000 (RJ45) in back
1xVHDCI SCSI connector
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
no PS/2 connection for KB / Mouse
(USB connectivity must be used instead)
IA64 Server Support CD, User Manual
Hereby the rack will be delivered
completely pre-mounted and
all wired connections are tested.
With racks 12U, 24U, 38U:
Systems and components
will be delivered installed in the rack
With racks 46U:
mounted into the PRIMERGY racks.
In case of the 46 U PRIMERGY rack,
this service has to be ordered,
to get the mounting kits and the
cables installed
ServerView:
FSC IA64 Server Support CD
for EFI service partition
Systems and components
will be delivered separately
To be ordered only together with
a PRIMERGY-
Mounting kit for PRIMERGY RXI300 is part of the basic unit
- 1 pair of telescopic rails (647 - 810mm)
PRIMECENTER rack
e.g.:
- 1 bracket DC-PC-Rack
S26361-K826-V10x
- 1 cable management for DC-PC-racks
refer configurator PC-Rack
max. 1x per System
Mounting kit for mounting of servers in in FSC 19" DataCenter- and
PRIMECENTER- racks and all server racks conforming to EIA standard
EIA-310-D for 19" racks.
Therefore the mounting kit is variable in depth from 647 - 810mm
- Connetion for KVM switch / Rack console
- RC22 can be directly connected (both USB and PS/2 connections)
- KVM S2 series needs the KVM S2 adapter USB-VGA
- For PS/2 KVM "S1" series as well as for standard PS/2 KB / Mouse
an additional USB to PS/2 adapter must be bought additionally and
connected to the RXI600. The adapter offers 2 x PS/2 ports.
Adaper order number, to purchase via PRIMEPOWER, is
D:GP70P-KA01 Adapter for PS/2<->USB
- Appropriate FSC USB keyboard is S26381-K340-V1*
This keyboard also needs USB cable T26139-Y3812-V1
A
Fujitsu Siemens Computers
5 of 10
Enterprise Products PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
A
Section
Processor
II
A two-way-processor system requires a multi-processor operating system.
Later upgrading to a two-way-processor system is also possible.
For a CPU extension the further CPUs must be of identical TLC (third level cache) and clock rate.
S26361-F3071-E263
S26361-F3071-E412
Itanium 2 1.6 GHz
Itanium 2 9015 1.4GHz
with 12 MB TLC on Chip,
heat sink and "Easy retention"
with 3 MB TLC on Chip,
heat sink and "Easy retention"
(Intel Codename "Fanwood")
occupies 2nd CPU socket
max. 1x per system
up to
1x
occupies 2nd CPU socket
max. 1x per system
Section
Memory
III
There are 8 memory slots available (2 banks, 4 modules each).
They can optionally be equipped with 1GB or 2GB registered DDR-RAM modules (PC2100).
The maximal extension is 16GB with 2GB modules!
Any mix of modules within one memory bank is not allowed.
One memory bank is allready occupied
S26361-F3070-E400
S26361-F3070-E800
Main memory 4 GB
Main memory 8 GB
PC2100 registered DDR RAM
PC2100 registered DDR RAM
up to
1x
consisting of 4 modules
with 1 GB each
consisting of 4 modules
with 2 GB each
occupies one bank
max. 1x per system
occupies one bank
max. 1x per system
Section
Hard disk drives
IV
S26361-F3066-E173
S26361-F3066-E114
Hard disk 73GB / 10K
Hard disk 146GB / 10K
10000rpm,<5.5ms, min. 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pin)
hot plug/hot replace tray
occupies one 1" bay
10000rpm,<5.5ms, min. 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pin)
hot plug/hot replace tray
occupies one 1" bay
onb. SCCI or RAID Controller
max. 2x per system
onb. SCCI or RAID Controller
max. 2x per system
up to
2x
S26361-F3066-E130
S26361-F3066-E573
Hard disk 300GB / 10K
Hard disk 73GB / 15K
10000rpm,<5.5ms, min. 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pin)
hot plug/hot replace tray
occupies one 1" bay
15000rpm,<4ms, min. 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pin)
hot plug/hot replace tray
occupies one 1" bay
onb. SCCI or RAID Controller
max. 2x per system
onb. SCCI or RAID Controller
max. 2x per system
Standard PRIMERGY harddisks must be ordered for upgrade.
To use these harddisks in the RXI300 a simple frame change must be carried out.
Upgrade harddisks are always delivered with standard PRIMERGY harddisk frames.
Unused harddisk positions in the PRIMERGY RXI300 are always equipped with fully
functional empty harddisk frames. Therefore, after the standard frame is removed, the
harddisk has to be mounted in the RXI300 specific empty frame.
The following harddisks are technically released for usage in the PRIMERGY RXI300:
S26361-F3121-L173
S26361-F3121-L114
S26361-F3121-L130
S26361-F3121-L573
HDD U320 10k 73GB hot plug 1"
HDD U320 10k 146GB hot plug 1"
HDD U320 10k 300GB hot plug 1"
HDD U320 15k 73GB hot plug 1"
B
Fujitsu Siemens Computers
6 of 10
Enterprise Products PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
B
Section
SCSI / Fibre Channel Controller
V
included in the basic unit
onboard 2 ch.SCSI Controller U320
connectivity
The system is equipped with a onboard dual channel Ultra 320 SCSI controller.
one channel can be connected to internal devices via the SCSI blackplane.
The two int. HDD's can be mirrored if they are connected to the
on-board controller with hot swap support.
1) for int. Drives, RAID 1
2) ext. VHDCI
The other SCSI channel can be used by external SCSI devices.
Fibre Channel controller for subsystems and SAN
S26361-F3141-E10
2GBit/s FC Controller
Emulex
LP1050, full height bracket
1 channel 2GBit/sec FC controller
LC Interface for 50um Fiber
PCI-X 64Bit / 133MHz, 170mm
3.3V / 5V tolerant signaling
max. 2x per system
Section
Disk Array
VI
Additional RAID Controllers for connection of external Disk Arrays in Subsystem SX31
S26361-F3006-E128
2-channel RAID Controller U320
LSI
The cables of the connection from the
subsystems (SX30) to the Raid
Controllers, see configurator SX30
320-2
128MB SDRAM ECC Cache
RAID 0, 1, 10, 5 & 50
default with TBBU
plug: internal 1x HD68;
external: 1x VHDCI
without cable
incl. SW and description (Ger/US)
64/66 PCI controller, 180mm
3.3V and 5V tolerant signaling
max. 2x per system
All Controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
C
Fujitsu Siemens Computers
7 of 10
Enterprise Products PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
C
Section
Communication / Network
VII
on-board LAN Controller
dual Gb Ethernet Contr. on-board
ext: 2 x RJ 45 connector
Teaming: Failover, Load Balancing
All released Intel PCI LAN Controllers can be used with the
on-board controller in Teaming Mode.
Single Port LAN Adapter
S26361-F3054-E1
S26361-F3053-E1
Gigabit Ethernet Contr. 1000SX
Eth.Ctrl 1x1Gbit PCI-X Pro/1000MF LC
Intel PRO/1000 MF Server Adapter
Adapter Teaming Support
Gigabit Ethernet Contr. 1000TX
Eth.Ctrl 1x1Gbit PCI-X Pro/1000MT Cu
Intel PRO/1000 MT Server Adapter
Adapter Teaming Support
PCI-X (PCI64/133), min 165 mm
ext:LC-connector
PCI-X (PCI64/133), min 165 mm
ext: for RJ45-connector, Cat 5
connection with Cat 5 cabling
SW: VLAN, Fast & Gbit Etherchannel
max. 2x per system
SW: VLAN, Fast & Gbit Etherchannel
max. 2x per system
3x
Dual Port LAN Adapter
S26361-F3011-E1
Gigabit Ethernet Contr dual 1000TX
Eth.Ctrl 2x1Gbit PCI-X PRO/1000MT Cu
Intel Pro/1000MT dual Server Adapter
Adapter Teaming Support
PCI-X (PCI64/66), min 163 mm
ext: for RJ45-plug, Cat 5
connection with Cat 5 cabling
SW: VLAN, Fast & Gbit Etherchannel
max. 2x per system
D
Fujitsu Siemens Computers
8 of 10
Enterprise Products PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
D
Section
System Management Products
VIII
FSC IA64 Server Support CD
The CD contains tools for installing of the system,
for update and for system diagnose.
The tools works in the EFI system partition.
Included in the basic unit.
Section
Country specific power cord
IX
Country specific power cords are not required for rack versions, except for USA&Canada.
Power cords are shipped in a rack version with inlet connector for non-heating apparatus.
Description in englisch. Both included in basic unit.
T26139-Y1742-L10
USA, Canada
For shipments to USA&Canada, you have to order
two power cords (1,8m, grey). For phase redundancy
2 Power Cords and 3 PSU's per system are needed.
End PRIMERGY RXI300
Fujitsu Siemens Computers
9 of 10
Enterprise Products PRIMERGY Server
System Configurator and Order-Information Guide
PRIMERGY RXI300 Status 2008-01-29
Change Report
Date
order number
changes
2006-11-02
2006-11-02
2006-11-02
2006-08-24
2006-08-25
2006-08-25
2005-12-20
2005-09-23
2005-06-02
2005-04-20
2005-04-07
2005-01-21
2004-12-17
2004-12-17
2004-11-05
2004-11-05
2004-11-05
2004-11-05
2004-11-05
2004-11-05
2004-05-12
S26361-F3071-E269
S26361-K963-V212
S26361-K963-V213
S26361-F3071-E412
S26361-K963-V948
S26361-K963-V944
S26361-F2843-E1
S26361-F3141-E10
S26361-F3066-E136
S26361-F3066-E130
Section IV
S26361-F3066-E173
S26361-F3071-E1xx
S26361-K963-V20x
S26361-F3071-E263
S26361-F3071-E269
S26361-K963-V210
S26361-K963-V211
S26361-K963-V212
S26361-K963-V213
Processor Itanium2 1.6GHz / 9MB TLC - no longer available
Rack mountable server 19" (2U) 1.6GHz / 9MB TLC / 4GB Memory - no longer available
Rack mountable server 19" (2U) 1.6GHz / 9MB TLC / 8GB Memory - no longer available
Processor Itanium2 9015 1.6GHz / 12MB TLC 400MHz FSB - now available
Rack mountable server 19" (2U) Itanium 2 9015 dual core processor; 8 GB Memory - now available
Rack mountable server 19" (2U) Itanium 2 9015 dual core processor; 4 GB Memory - now available
2GBit/s FC Controller Emulex LP9802, PCI - no longer available
2GBit/s FC controller Emulex LP1050 - now available
Hard disk 36GB / 10K - no longer available
Hard disk 146GB / 10K - now available
Basic unit without HDDs - now available
Hard disk 73GB / 10K - now available
2. Processor Itanium 2 (Madison) - no longer available
Basic units with Itanium 2 (Madison) processor - no longer available
Processor Itanium2 1.6GHz / 3MB TLC Fanwood - now available
Processor Itanium2 1.6GHz / 9MB TLC - now available
Rack mountable server 19" (2U) 1.6GHz / 3MB TLC Fanwood / 4GB Memory - now available
Rack mountable server 19" (2U) 1.6GHz / 3MB TLC Fanwood / 8GB Memory - now available
Rack mountable server 19" (2U) 1.6GHz / 9MB TLC / 4GB Memory - now available
Rack mountable server 19" (2U) 1.6GHz / 9MB TLC / 8GB Memory - now available
First draft
Fujitsu Siemens Computers
10 of 10
Enterprise Products PRIMERGY Server
|