S Y S T E M S O L U T I O N T O P O L O G I E S
SST-SX
he Crown SST-SX module is a fourth-order
Linkwitz-Riley type crossover with the
T
crossover point switchable to either 80 or
120 Hz. High-frequency (HF) signals are routed to
the internal amplifer channels, and low-frequency
(LF) signals are summed and routed the mono
output connector. Truly a professional crossover,
the SST-SX uses hard-wired precision compo-
nents that stay at the frequencies you have
selected for consistent bandwidth control.
SST (System Solution Topologies) modules install
into the back of Crown SST-compatible amplifiers,
saving rack space and simplifying system wiring.
•
Neutrik® Combo (¼-inch (6.35-mm) phone
and 3-pin XLR) input jacks.
Features
•
•
•
•
Stereo biamp.
•
•
Male 3-pin XLR Sub Output.
For more details about the Crown SST-SX, con-
tact the Crown Technical Support Group at
800-342-6939 or 574-294-8200. Also, visit the
24-dB/octave Linkwitz-Riley tuned filters.
Crossover switchable to either 80 or 120 Hz.
Optional high-pass filter bypass on amplified
outputs adapts system for full-range use.
SST modules install into the back of your
amplifier, saving rack space and simplifying
system wiring.
•
SST Modules add flexibility by allowing you to
tailor your Crown Contractor (CH/CL) Series
or CE Series amplifier to your application.
Specifications
Note: Specifications describe typical results using the
SST-SX crossover module installed in a Crown SST-
compatible amplifier. All measurements are in Stereo
mode with 8-ohm loads and an input sensitivity of
26-dB gain at 1-kHz rated power unless otherwise
specified. Specifications for units supplied outside
the U.S.A. may vary slightly at different AC voltages
and frequencies.
OUT
80 / 120 Hz HP
24 dB/oct. slope
CH1
HOST
AMPLIFIER
BYPASS
3
CH1 INPUT
2
IN
1
80 Hz
Performance
Frequency Response: 0.1 dB from 20 Hz to 20
120 Hz
kHz at 1 watt.
Signal to Noise Ratio,
80 / 120 Hz LP
A-Weighted: Better than 105 dB below rated 1-kHz
power;
24 dB/oct. slope
SUB OUT
(SUMMED)
80 / 120 Hz LP
24 dB/oct. slope
20 Hz to 20 kHz: Better than 100 dB below rated
1-kHz power.
80 Hz
Total Harmonic Distortion (THD): 1-kHz rated
power, 1.0% or less true THD from 20 Hz to 20
kHz.
OUT
IN
CH2
HOST
AMPLIFIER
CH2 INPUT
120 Hz
BYPASS
3
2
Crosstalk: Better than 50 dB below rated power,
20 Hz to 20 kHz.
1
80 / 120 Hz HP
24 dB/oct. slope
Input/Output
Input Impedance:
SST-SX Block Diagram
Nominally 20 k ohms, balanced. Nominally 10 k
ohms, unbalanced.
Output Impedance: 600 ohms, balanced.
Maximum Output: +15 dBm into 600 ohms.
Crown’s Three-Year, No-Fault, Full Warranty
Crown offers a Three-Year, No-Fault, Full Warranty for every new Crown amplifier product—an
Crown Audio, Inc.
P.O. Box 1000
unsurpassed industry standard. With this unprecedented No-Fault protection, your new Crown ampli-
fier product is warranted to meet or exceed original specifications for the first three years of ownership.
During this time, if your unit fails, or does not perform to original specifications, it will be repaired or
replaced at our expense. About the only things not covered by this warranty are those losses normally
covered by insurance and those caused by intentional abuse. And the coverage is transferable, should
you sell your unit.
Elkhart, IN 46515-1000
TEL: 574-294-8200
FAX: 574-294-8FAX
Specifications subject to change without prior notice. Latest
Crown is a registered trademark of Crown International, Inc.
Other trademarks are the property of their respective owners.
Printed in U.S.A.
See your authorized Crown dealer for full warranty disclosure and details. For customers outside of the
USA, please contact your authorized Crown distributor for warranty information or call 574-294-8200.
© 2003 Crown Audio, Inc.
4-03
132300-1A
|