English
®
GR380/85 UK p01-11
1
20/3/00, 3:57 pm
Your mower will continue to run
for a short time after releasing
the switch lever. Always allow
your mower to stop on its own.
ENGLISH
•
Release the switch lever to turn your
mower off and remove the plug from
the mains:
Maintenance and storage
•
Store your mower in a dry place when
not in use, out of the reach of children.
•
Whenever you leave your mower
unattended.
•
Do not use solvents or cleaning fluids to
clean your mower - use a blunt scraper
to remove grass and dirt.
•
Before checking, cleaning, adjusting
or working on your mower.
•
•
Before clearing a blockage.
•
•
Always disconnect from the electrical
supply before cleaning.
If your mower starts to vibrate
abnormally (check immediately).
Replace worn or damaged parts for
safety. Do not operate your mower if any
parts are defective; discard all defective
parts and fit new parts before use.
•
After striking a foreign object, inspect
your mower for damage and make
repairs as necessary.
•
Never run your mower whilst lying on its
side or attempt to stop the blade -
always allow it to stop on its own.
•
•
Keep all nuts, bolts and screws tight to
be sure your mower is in a safe working
condition.
•
•
•
Do not put hands or feet near or under
rotating parts.
Use only Black & Decker recommended
replacement parts and accessories.
Keep clear of discharge openings at all
times.
Black & Decker’s policy is one of continuous
improvement to our products and, as such, we
reserve the right to change product specifications
without prior notice.
Start your mower carefully according to
the instructions and with your feet well
away from the blade.
•
Do not use your mower in the rain and
do not allow it to get wet. Avoid using
your mower in wet grass, if possible.
Double insulation
Your mower is double insulated.
•
•
•
•
•
Use your mower only in daylight or good
artificial light.
This means that all external metal parts are
electrically isolated from the power supply.
This is achieved by placing an extra
insulation barrier between the electrical and
mechanical parts. Double insulation means
greater electrical safety and obviates the
necessity of having your mower earthed.
Do not pull your mower towards you or
walk backwards when in operation.
Do not cross gravel paths or roads whilst
the blade is rotating.
Always be sure of your footing,
particularly on slopes.
Always cut across the face of slopes, never
up and down. Exercise extreme caution
when changing direction on slopes.
Electrical safety (UK only)
Your mower should always be switched off
at the mains before disconnecting any plug
and socket connector or extension cables.
!
•
•
Do not cut excessively steep slopes and
always wear non-slip footwear.
Fuse replacement
If your mower is supplied with cable fitted
with a non-re-wireable plug:
Check the grassbag (if supplied) for wear
or damage and replace if necessary.
•
•
Walk, never run. Do not force your mower.
•
The plug is fitted with a 13 amp fuse
which is the recommended fuse for
your mower.
Never pick up or carry your mower while
the motor is running.
•
Ensure the blade has stopped rotating
and take extreme care before lifting your
mower for and during transportation.
•
•
Only use replacement fuses which are
approved to BS1362.
When changing the fuse in your plug,
always ensure the fuse cover is refitted.
If the fuse cover is missing or damaged
do not use the plug.
•
Never operate your mower with defective
guards or shields.
3
GR380/85 UK p01-11
3
20/3/00, 3:58 pm
Note: Fuses do not give personal protection
against electric shock.
Features (Fig. A)
Your purchase of a Black & Decker GR380/
Plug replacement
A
GR385 range lawnmower gives you a
product combining quality with modern
design and the following features to provide
safe, efficient and easy mowing.
•
•
Disconnect the plug from the supply.
Cut off the plug and dispose of
immediately. Insertion of a detatched
plug into a 13 amp socket outlet may
result in electric shock.
•
Lock-off safety switch to prevent
accidental starting of your mower.
•
A blade brake (AUTOSTOP) for added
safety. Stops the blade rotating within
3 seconds once the switchbox lever is
released.
•
•
Only fit BS1363A approved plugs fitted
with the correctly rated fuse.
The cable wire colours, or a letter, will be
marked at the connection points of most
good quality plugs. Attach the wires to
their respective points in the plug (see
below). Brown is for “Live” (L) and blue is
for “Neutral” (N).
•
•
Large handle nuts for easy assembly
and storage.
The wheels are in line with the outside of
your mower body which allows cutting
right up to the edge of the lawn.
•
Before replacing the top cover of the
mains plug ensure that the cable clamp
is holding the outer sheath on the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
•
Conversion to a mulching lawnmower by
simply removing the grassbox.
•
•
Three height of cut positions.
Tough, durable plastic deck which will
not rust and contributes to low noise and
low vibration.
Fit the recommended
fuse approved
to BS1362
Fit a BS1363A
approved
resilient plug
•
Powerful and efficient induction motor
which gives effective cutting and bagging
in all reasonable conditions and a low
noise level as well as low maintenance.
Connect blue
to N (neutral)
Connect brown
to L (live)
•
Ergonomically designed upswept handle
for comfortable use and ease of pushing.
•
•
Easy grassbox removal.
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Cable restraint helps keep the cable out
of the way and prevents the cable socket
being accidentally pulled and disconnected.
230 volts AC only
Never use a light
socket
Warning! Never connect live or neutral wires
to the earth pin marked “E” or
Carton contents
Mower carton containing:
.
!
Note: Do not wire an extension cable directly
into your mower yourself. Instead, take your
mower to your nearest Black & Decker
service agent.
•
•
•
Mower body.
12m of cable (UK only).
Grassbox.
Increased safety can be obtained by having
a qualified electrician install a high sensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, then we strongly recommend that
the electrical power to your mower be
supplied through a high sensitivity (30mA)
residual current device (RCD). The RCD is
designed to provide a high degree of
Loose parts pack containing:
•
•
•
•
1 spanner.
User manual including guarantee card.
Service sheet.
2 screws.
Handle assembly (Fig. B)
personal protection against harmful electric
current should fault conditions occur.
Remove all the parts from the carton and
familiarise yourself with the individual parts of
your mower.
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
your mower from the safety instructions and
safe working practices given in this manual.
The main parts of your mower are your
mower body (1) which comprises a motor
cover (2), wheels (3) and grass flap (4).
!
4
GR380/85 UK p01-11
4
20/3/00, 3:58 pm
The handle comprises the upper handle (5),
cross bar (20), lower handle (6), switch box
(7), switch lever (8), safety lock-off (9), electric
cable (10), cable clips (11), wing nut and cup
(12) and cable clip (21).
ENGLISH
Insert cross member (20) through cable
B1 •
clip (21). Assemble left lower leg (6L) and
right lower leg (6R) onto cross member
(20). Clip upper handle (5) over cross
member ends, and fasten into place with
nuts (12).
Removing the grassbox from your mower:
The full grassbox may be removed by raising
the grassflap and then either lifting the
grassbox up and through the lower handle(s)
or by freeing the grassbox from its mounting
and then resting it on the lawn, while the
grassflap is gently lowered, leaving both
hands free to gently lift the full grassbox.
To assemble the lower handle (6) into the
correct locations on your mower body (1),
proceed as follows:
Insert the lower handles into the two
B2 •
holes in your mower body (1) and press
down until secure. Secure in position
using the screws supplied (19).
How to use your mower (Fig. E & G)
Observe all of the relevant warnings when
using your mower.
!
We recommend the directional method of
Height of cut adjustment (Fig. C)
G
operation to obtain the maximum cutting
performance from your mower and to reduce
the risk of the trailing extension lead from
entering the cutting path.
Before wheel assembly adjustment ensure
your mower is disconnected from the mains.
Each of the two axle wheels has its own
means of height adjustment which gives
3 cutting height positions.
•
Place the bulk of the supply cable on the
lawn close to the starting point (Fig. G,
position 1).
•
To select a height of cut, move the
wheels (3) into the slot required using the
spring system (13).
•
Hold the handle assembly with both
hands.
C
Your switch box incorporates a cable
restraint. To fix the cable to the restraint,
proceed as follows:
•
Fit the other three wheels in the same way.
To ensure an even cut, please make sure
that all four wheels are placed in the same
position.
•
Bring the socket end of the extension
cable from behind and connect it to your
mower plug.
Grassbox assembly (Fig. D)
•
Form a loop on your extension cable
close to the switch box.
Read the safety instructions at the beginning
of this manual before using this accessory.
E1 •
Push the loop through the slot from the
opposite side of the restraint hook (Fig. E1),
position the loop over the h ook and pull
the cable back through the slot. Your
cable will now be restrained.
•
The grassbox is a two piece (14 & 15)
plastic construction which needs to be
assembled before attaching it to your
mower.
To assemble the grassbox, proceed as
follows:
•
The extension cable should now fall
away from your mower and behind the
operator, ready for use.
Align both parts together.
D1 •
Warning! Do not attempt to operate your
mower with one hand - you must guide it
with both hands.
!
Clip in place.
D2 •
E2 •
raise the front of your mower and to
reduce the risk of lawn damage whilst
starting, depress the safety lock-off
button (18) on the switchbox (7) and
whilst still depressed pull the switch lever
(8) towards you. Your mower will start
and you can now allow the lock-off
button to be released and lower your
Tilt the handle downwards to slightly
D3 F•itting the grassbox to your mower:
The spring loaded grass flap is lifted and
the two arms on the front edge of the
grassbox are located behind the two lugs
rising up from the rear edge of the cutter
deck (Fig. D3).
•
The grass flap can now be released to
lock the grassbox into position.
5
GR380/85 UK p01-11
5
20/3/00, 3:58 pm
mower to its proper cutting position
and commence cutting.
•
•
Turn your mower over on its side so that
the underside of the cutter deck is
exposed.
F
•
Proceed down the cutting area as shown
in Fig. G (a), working from position 1
towards position 2 and, on reaching
position 2, turn to the right and proceed
towards position 3. Continue to the end
of the cutting area, turn to the left and
proceed towards position 4.
Using a cloth placed over the blade or
heavy duty gloves to protect your hands,
grip the blade and, using the spanner
provided, loosen and remove the nut (16)
from the motor spindle. Turn the nut in an
anti-clockwise direction to loosen it.
Continue in the same manner as shown
in Fig G, always working away from the
cable. Do not adopt the method as
shown in Fig. G (b), working towards the
cable, as this is dangerous practice.
•
The blade can now be replaced and the
washer and nut reassembled.
Note: Do not remove the impeller (17) for
any reason.
Note: Some mowers are fitted with a clutch
washer , between the blade nut and the
blade, which must be reassembled at all
times.
Your mower will continue to operate whilst
you are depressing the switch lever. To stop
your mower release the switch lever.
When you have finished using your mower
we recommend that you clean all debris from
it before putting it away. Refer to the ‘Care
and maintenance’ section.
Handy hints
•
On long grass, above 10cm (4 inches), use two
cuts to get a close finish. We recommend that
the first cut should be taken with the blade set at
maximum height of cut and the second taken
with it set at medium or close. This will prove to
be easier and give a better overall finish to
your lawn.
Note: To obtain the best results cut your
lawn or grass area regularly and do not cut
when the grass is wet.
If, when grasscutting, loose grass is seen to
be scattering from beneath your mower, the
grassbox is probably full and should be
emptied.
Care and maintenance
The advice given in this section covers the
Blade maintenance
general care and maintenance of the main
body of your mower. Advice relating to the
blades is given in “Maintenance of blades”.
The steel blade is designed to give a fine
finish in long or tough grass. The blade will
continue to cut even when it has become
blunt or burred. There is no need for it to be
razor sharp.
Warning! Do not use a cable which shows
signs of damage. Fit a new cable completely
- do not make any permanent or temporary
repairs.
!
If, however, because of damage or wear the
cutting performance deteriorates, then your
mower may require a new blade, or at least
the existing blade to be sharpened.
•
Always keep your mower clean and free
from grass cuttings, especially the
underside of the cutter deck and the
air vents.
We recommend that the steel blade is
sharpened or a new blade fitted at the
beginning of each season.
•
•
Check all electrical cables at regular
intervals, looking for signs of wear,
abrasion or other damage.
Replacement blades are available from Black
& Decker service agents.
At the end of each cutting session we
recommend that the build up of grass on
the underside of the cutter cover is
removed using a blunt scraper.
Warning! When fitting a new blade use only
the Black & Decker replacement part
specified for your mower - do not attempt to
fit any other blade.
!
•
Clean all plastic components with a
damp cloth.
Fitting a new blade (Fig. F)
Caution: Do not use solvents or cleaning
fluids as these may damage the plastic
components of your mower.
Observe all the relevant warnings before
changing the blade.
!
Warning! Disconnect your mower from the
electrical supply before changing the blade.
6
GR380/85 UK p01-11
6
20/3/00, 3:58 pm
Fault finding
ENGLISH
If your mower does not operate correctly,
use the table below to locate the problem.
Warning! Always disconnect your mower
from the electrical supply before carrying out
any inspection.
!
workmanship, we guarantee to either replace all
defective parts, or at our discretion, replace your
mower free of charge, provided that:
Symptoms
Possible cause Remedy
Motor buzzes Blade jammed. Disconnect from
but blade does
not move.
the electrical
supply.
•
Your mower is returned to one of our authorised
repair agents with evidence of purchase.
Remove
obstruction from
the blade.
•
Your mower has been used within the
parameters of its consumer classification.
•
•
Your mower has not been used for hire purposes.
No noise and Faulty electrical Disconnect from
Repairs have not been attempted by anyone
other than our authorised repair agents.
blade does
not move.
connection.
the electrical
supply.
•
The failure represents normal wear and tear.
Plug your mower
into an alternative
compatible
This guarantee is offered as an extra benefit and is
additional to your statutory rights.
electrical supply.
Fit a new fuse.
Our guarantee policy
Failure due to the following are not covered:
Re-tighten and
check all electrical
connections in
•
Replacing worn or damaged blades, nylon line
and chains, or cables damaged during storage
or use. These are regarded as replacement items
which wear during normal usage.
extension cables.
Re-set RCD in
accordance
with instructions.
•
•
Failure as a result of sudden impact or obvious
abuse.
Failure due to usage not in accordance with
instructions and recommendations contained in
this manual.
What to do if your mower needs
repair
The use of other than genuine Black & Decker
accessories and parts may damage or reduce the
performance of your Black & Decker mower and may
render the guarantee void.
For after sales service please refer to the section
‘Lawnmowers & Garden’ within your local
Yellow Pages.
Unwanted products and the
environment
Black & Decker after sales service
(UK, Australia and New Zealand only)
Should you find one day that your mower
needs replacement, or is of no further
use to you, think of the protection of the
environment. Black & Decker service agents
will accept your old mower and will dispose of
it in an environmentally safe way.
Black & Decker offers a nationwide network of
authorised service agents. The use of other than
genuine Black & Decker accessories and parts may
damage or reduce the performance of your
Black & Decker product and may also endanger the
user. The terms and conditions of the warranty may
also be effected.
Black & Decker lawn and garden
guarantee
This guarantee provides 36 months parts cover
and 12 months labour (UK), 24 months parts
cover and labour (Australia and New Zealand).
In all cases proof of purchase will be required.
It is our aim that all Black & Decker customers should
be totally satisfied with their Black & Decker product
and after sales service, if help or advice is needed
please contact a local Black & Decker authorised
repair agent who will be happy to help. Full details of
our after sales service can be obtained from any of
our Black & Decker authorised repair agents.
lf your Black & Decker mower becomes defective,
within the guarantee period, due to faulty materials or
7
GR380/85 UK p01-11
7
20/3/00, 3:58 pm
ENGLISH
Other Black & Decker products
(UK only)
Black & Decker has a full range of outdoor power
tools that make life easy in the garden. If you would
like further information on other products, please
contact the Black & Decker Service Information
Centre at the address towards the back of this
manual, or contact your Black & Decker stockist.
Lawnmowers
Chainsaws
String trimmers
Lawnrakers
Compost shredders
Blade trimmers
Cordless trimsaws
Cordless shears
Leafbusters
Cordless brooms
Cordless shrubbers
Hedgetrimmers
EC Declaration of Conformity
We declare that units:
GR380, GR385
conform to 98/37/EC,
89/336/EEC, 73/23/EEC
A weighted sound pressure @ 4m 73dB (A)
A weighted sound power 93dB (A)
Hand/arm weighted vibration <2.5m/s2
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG
United Kingdom
8
GR380/85 UK p01-11
8
20/3/00, 3:58 pm
GR380/85 UK p01-11
9
20/3/00, 3:58 pm
Australia
Black & Decker (A’asia) Pty Ltd
286-288 Maroondah Highway, North Croydon, Victoria 3136 Fax: 03 9726 7150
Tel: 03 9213 8200
New Zealand
South Africa
Black & Decker
483 Great South Road, Penrose, Auckland
Tel: 09 579 7600
Fax: 09 579 8200
Black & Decker South Africa (Pty) Ltd
Suite no 107, PostNet X65, Halfway House 1685
Tel: 011 314 4431
Fax: 011 314 4435
United Kingdom Black & Decker
210 Bath Road, Slough
Tel: 01753 574277
Tlx: 848317 BAND MH
Fax: 01753 551155
Berkshire SL1 3YD
®
10/97.1
GR380/85 UK p01-11
10
20/3/00, 3:58 pm
GR380/85 UK p01-11
11
20/3/00, 3:58 pm
10/97.1
GR380/85 UK p01-11
12
20/3/00, 3:58 pm
®
GR380
GR385
GR380/85 UK p01-11
13
20/3/00, 3:58 pm
A
8
7
10
20
21
5
6R
12
1
2 4
15
14
6L
3
B1
C
B2
5
3 13
12
20
11
12
6R
6L
GR380/85 UK p01-11
14
20/3/00, 3:58 pm
D2
D3
D1
E1
F
15
14
E2
8
18
7
G
16
17
GR380/85 UK p01-11
15
20/3/00, 3:58 pm
|