FULL MANUAL
DIRECT DRIVE TURNTABLE
STR8-30
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AS S EMBLY
1. Remove the main unit with the packing from the box
and take off the packing.
2. Insert the turntable platter onto the center spindle.
3. Set the slip mat on the platter.
of the tonearm.
7. Adjustment of horizontal zero (0) balance and
stylus pressure:
(a) Remove the stylus protector, do not touch the
stylus tip during the adjustment.
4. Installation of cartridge:
When installing a cartridge, refer to the operating
instructions of that cartridge.
(d) Release the arm clamp and lift the tonearm
from the arm rest to free it.
During installation, attach the stylus protector to
guard the stylus tip from damage.
(1) Connect the lead wires to the cartridge terminals.
The terminals of most cartridges are color coded.
Connect each lead wire to the terminal of the
same color.
(c) Rotate the counterweight until the tonearm is
approximately balanced horizontally (floats
freely).
(d) Refasten the tonearm with the arm clamp.
(e) Hold the counterweight stationary with one
hand and rotate only the stylus-pressure ring
to bring the number "0" of the ring into
alignment with the center line on the tonearm
rear shaft.
(f) Rotate the counterweight clockwise until the
scale shows the value corresponding to the
pressure of the used stylus. The average stylus
pressure of the cartridge body is 1.5-2 g. If
you use a non-Stanton cartridge, please follow
that manufacturer’s instructions.
White
Blue
Red
(L+) .…....………….... Left channel+
(L-)....………............... Left channel-
(R+) ……....….......... Right channel+
(R-) .………..…......... Right channel-
Green
(2) Install the cartridge to the headshell and tighten
it with screws provided with the cartridge.
5. Insert the headshell into the front end of the
tonearm, then turn the lock nut clockwise with the
headshell firmly held horizontally.
6. Slide counterweight onto tonearm.
8. Install the dust cover to the main unit.
Twist it lightly and it will screw onto the rear shaft
P LACEMENT
or through the air resulting in feedback. Find a
location which is very stable and vibration free.
• The legs have functions for adjusting the height of
the unit itself. Adjust the legs to stabilize the main
body horizontally.
• Do not place the unit in a location where it will be
exposed to direct sunlight or near a heating appliance.
• Do not place the unit in a location where there is high
humidity or a lot of dust.
• Cartridge may pick up slight sound pressures or
vibrations from the speakers coming along the floor
CONNECTIONS
1. Connect the power cord to the auxiliary power outlet
on the rear panel of your amplifier or receiver or to a
household AC outlet.
NOTE:
Be sure to connect the ground terminal firmly to the
amplifier or receiver.
2. Connect the unit output terminals to the PHONO
jack of your amplifier or receiver.
If this connection is not made or is loose, a power
source "HUM" will result.
Output terminals
L (White)
R (Red)
Amplifier(Receiver)
L Channel
>>
>>
>>
R Channel
GND
GND (Spade)
OP ERATION
1. Rotate the power dial clockwise to turn on the
power, the speed indicator and the strobe-
illuminator will light up.
2. Place a record on the slip mat, when playing a
45rpm record with a large center hole, place the
45-rpm adaptor on the center spindle.
5. Press the Start/Stop button, the turntable platter
will start to rotate.
6. Move the tonearm over the desired groove.
7. When play is finished, move the tonearm to the
arm rest, secure the tonearm with the arm clamp.
8. Press the Start/Stop button to stop the platter
rotating, push the power button to turn off the
power.
3. Set the speed to match the record.
4. Remove the stylus protector, release the arm clamp.
MAINTENANCE
•For best results & proper care of your equipment use
Stanton Vinyl Cleaner (VC-1) for your records and
Stylus Cleaner Kit for styli (SC-4).
•Clean the stylus periodically with a soft brush to
prevent the accumulation of dust.
•From time to time, the dust cover and turntable
cabinet should be wiped with a soft and dry cloth.
•Any volatile materials such as alcohol, thinner,
benzine, etc., may remove the paint or damage the
lustre, please avoid.
•When the sound becomes distorted or noisy, check
the stylus. If worn out, replace it with a new one.
S P ECIFICATIONS
*General
Power supply..…...………...AC 115/230V~, 50/60Hz
Power consumption..........................................9 Watts
Dimension(WxDxH).........….......450 x 350 x 140 mm
Weight..................................................…........4.6 Kgs
For improvement purposes, specifications and design may be changed without notice.
502-STR830-1213
|