E S M -1 1
PROFESSIONAL STEREO PREAMP MIXER
O W N E R M A N U A L
’
S
E S M -1 1
R e g is t e r t h is p r o d u c t o n lin e
@
@
w w w . s t a n t o n m a g n e t ic s . c o m
© 2000, Stanton Magnetics, LLC
DESCRIPTION OF FUNCTIONS
1. Master level control: Controls the overall signal output level of the Master output
2. Mic volume control: Controls the overall microphone output level
3. Microphone input: 1/4” connector
4. Input selector switches: Selects phono or line inputs of channels 1 and 2
5. Channel faders: Control the output level of channels 1 and 2
6. Crossfader Reverse: Reverses the direction of the crossfader
7. Crossfader: Fades the master output between channels 1 and 2
8. Level meter: The level meter displays the master output stereo signal level
9. Power switch: Selects power "ON" or "OFF"
10. Power Indicator: LED indicates whether mixer is ON or OFF.
11. Cue pan: Fades the headphone output between channels 1 and 2, effectively allowing
the user to preview a mix.
12. Cue level control: Controls the overall headphone output level.
13. Headphone output: Connection for 1/4 inch headphone.
headphone impedance is 32-200 ohms for maximum volume
Recommended
14. Ground connector: Connects to the turntable ground connector to eliminate electrical
hum. Ground cables are usually supplied with turntables
15. Line inputs: Line signal inputs for channels 1 and 2
16. Phono inputs: Phono signal inputs to connect turntables to channels 1 and 2
17. Master output: Level is controlled by master level control (1)
18. REC output: Record out connects to tape recorder, mini disk recorder, etc. to
record performance
19. Power supply connector: Input connection for the accompanying power supply.
TECHNICAL SPECIFIC ATIONS
CROSSFADER CLEANING
The ESM-11 crossfader may need lubrication from time to time. This will extend
the fader life and eliminate any potential damage due to extended heavy usage.
Line inputs:
2 (RCA), 150 mV / 47K ohm
2 (RCA), 3 mV / 47K ohm
1 (1/4 inch), 1.5 mV / 600 ohm
1 (RCA), 1V / 600 ohm
Phono inputs:
DJ mic input:
Master output:
Record output:
Headphone output:
Frequency Response:
S/N Ratio:
Cleaning Instructions
1. Remove the crossfader by unscrewing the 2 outer screws (removing the 2
inner screws will detach the fader from the fader plate) and disconnecting the
cable from the mixer.
1 (RCA), 330 mV / 600 ohm
1 (1/4 inch), 32 - 200 ohms recommended
20 Hz - 20 kHz, +/- 0.5 dB
Less than 80dB
2. Spray a small amount of cleaner or lubricant into both ends of the fader and
slide the fader back and forth a few times to spread the fluid evenly throughout
the fader.
T.H.D:
0.01% at 1KHz
Dimension(LxWxD):
Weight:
9” x 9.8” x 3.5” (230 x 250 x 90 mm)
7 Lbs (3 Kg)
3. Shake and wipe off excess fluid before re-assembling the fader.
WARRANT Y
CROSSFADER REPL ACEMENT
To replace the crossfader, follow step 1 of the cleaning instructions.
Replacement parts are available from Stanton or your local Stanton dealer.
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materi-
als (limited as specified below), and workmanship for a period of thirty
six (36) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
FOR THE WARRANTY TO BE VALID, PLEASE COMPLETE THE
ONLINE WARRANTY REGISTRATION FORM FOUND AT
WWW.STANTONMAGNETICS.COM
2821 Evans Street • Hollywood, FL 33020
|