Sony TV Mount 411 User Manual

I N S T A L L AT I O N I N S T R U C T I O N S  
Universal Pitch-Adjustable Wall Mount  
For Flat Panel Display PLP-91/D  
Can Be Used to  
Lock Display  
Your new Wall Mount (PLP-91/D) is a quick disconnect  
mounting system with adjustability between 0 and  
15 degrees pitch.  
Once the Universal Flat Panel Display Wall Mount  
Bracket is attached to your display, simply attach the  
mount securely on a wall, lock the display in place using  
the convenient Q-latch, and attach your audio/video  
cables.  
The PLP-91/D is virtually invisible when your display is  
mounted.  
BEFORE YOU BEGIN  
Caution: To prevent damage to the PLP-91/D, which could affect or void the Factory warranty, and to the equipment  
that will be attached to it, thoroughly study all instructions and illustrations before you begin the installation. Pay par-  
ticular attention to the “Important Warnings and Precautions” on Page 1.  
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the mount must  
be capable of supporting five times the total weight of the equipment.  
The maximum weight to be installed on the Universal Pitch-Adjustable Wall Mount is 125 pounds (56.7 Kg).  
Sony Electronics Inc. 8805-000087  
1 Sony Drive  
Park Ridge, NJ 07656  
201-930-1000  
 
Installation Instructions  
Pitch-Adjustable Mount PLP91/D  
CONTENTS  
DIMENSIONAL DRAWING .............................. 3  
INSTALL MOUNT .............................................. 4  
INSTALL PSB-91/D DISPLAY BRACKETS..... 4  
MOUNT THE DISPLAY ..................................... 6  
TOOLS REQUIRED FOR INSTALLATION  
Phillips screwdrivers, No. 1 and No. 2 TIP  
Drill and bit set  
Wrench set  
NOTE: Other tools may be required depending on the  
method of installation.  
2
 
Installation Instructions  
Pitch-Adjustable Mount PLP91/D  
Tighten this screw  
to lock tilt in place  
DIMENSIONAL DRAWING  
3
 
Installation Instructions  
Pitch-Adjustable Mount PLP91/D  
INSTALL MOUNT  
Mounting  
Holes  
Install the mount as follows:  
1. Determine the exact mounting location prior to installation and  
draw a level line to indicate the desired height for the top of the  
mounting plate.  
WARNING: Improper installation can result in serious per-  
sonal injury! Make sure that the structural  
framework can support a weight factor five times  
the total weight of the equipment. If not, reinforce  
the structure before installing the mount.  
Mounting  
Holes  
2. With the mount correctly oriented and level, secure the mount  
to the wall (see Figure 1) using four fasteners (not included).  
Fasteners must be driven into the supporting wall studs or other  
supporting framework.  
Figure 1. Mounting Hole Locations  
3. Check mount to ensure it is level and adjust to level if  
necessary.  
INSTALL PSB-91/D DISPLAY BRACKETS  
10-24 Button Head  
Cap Screw  
1. Using a 10-24 button head cap screw inserted from the back  
side of the bracket, secure the mounting button, with cham-  
fered hole of mounting button (larger surface) facing the  
bracket, to bracket (four places) (see Figure 2 and Figure 3).  
Mounting Button  
2. Place Nylon spacers over the mounting holes on the back of the  
screen.  
Figure 2. Mounting Button Attachment  
Attach Mounting Buttons  
Using These Holes  
Figure 3. Mounting Button Location  
4
 
Installation Instructions  
Pitch-Adjustable Mount PLP91/D  
3. Attach mounting brackets to the display using the M5 screws  
for 32” screen or M6 for the 42” and 50” screens (see Figure 4  
and Figure 5).  
Nylon Spacer  
6mm  
Nylon Spacer  
6mm  
Nylon Spacer  
5mm  
50” Display  
42” Display  
32” Display  
Figure 4. Bracket Hole Location  
50”  
42”  
32”  
Figure 5. Bracket Attachment Location  
5
 
Installation Instructions  
Pitch-Adjustable Mount PLP91/D  
MOUNT THE DISPLAY  
Mount the display as follows:  
Security Lock May Be  
Installed  
1. Make sure no power is supplied to the display and the flag is in  
the lowered (open) position before attempting to mount the dis-  
play.  
2. Using two people, slide the display down over the mount.  
Make sure all four Q-buttons of the display engage all four  
slots in the mount.  
3. With the Q-buttons of the display fully engaged in the slots of  
the mount, secure the display on the mount by raising the flag  
all the way to their locked position. If the flag does not fully  
engage, remove the display and make sure the brackets are  
correctly installed.  
Figure 6. Optional Security  
NOTE: A security lock may be installed through the hole in the  
locking flag for additional security (see Figure 6).  
Loosen or tighten  
this bolt  
to adjust tilt tension  
or lock in place  
NOTE: If display does not remain at desired tilt setting, tighten  
the nut and bolt on tilt arms on each side (see Figure 7).  
WARNING: Make sure the flag securing the display is com-  
pletely lowered at all times except when removing  
or installing the display. The flag must be all the  
way down when installing/removing cables.  
Figure 7. Tilt Tension Adjustment  
6
 

Sony Clock Radio ICF CD873 User Manual
Sony Headphones MDRXB700 User Manual
Sony Stereo Amplifier XM ZR1252 User Manual
Speco Technologies Computer Monitor VM 1705C User Manual
Speco Technologies Security Camera CVC 770PH User Manual
Stanton DJ Equipment SCS1m User Manual
StarTechcom Switch SV431H User Manual
Sunbeam Blender 4816 8 User Manual
Sylvania CRT Television 4813LT User Manual
Targus Mouse 400 0140 001A User Manual