CAMERA ADAPTOR
CA-590/590P
The supplied CD-ROM includes operation manuals for the CA-590/590P, CCU-590/590P, and CCU-790/
790P (English, Japanese, French, German, Italian, and Spanish versions) in PDF format.
OPERATION MANUAL [English]
1st Edition (Revised 1)
Pour les clients européens (pour CA-590P)
Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan,
Minato-ku, Tokyo, Japon.
Le représentant autorisé pour EMC et la sécurité des produits
est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Allemagne. Pour toute question concernant le
service ou la garantie, veuillez consulter les adresses
indiquées dans les documents de service ou de garantie
séparés.
Für Kunden in Europa (für CA-590P)
Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1
Konan, Minato-ku, Tokyo, Japan.
Der autorisierte Repräsentant für EMV und Produktsicherheit
ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in
Bezug auf Kundendienst oder Garantie wenden Sie sich bitte
an die in den separaten Kundendienst- oder
Garantiedokumenten aufgeführten Anschriften.
3
Table of Contents
c AU-294 board.................................................................... 11
Attaching the CA-590/590P to a BVP-E10/E10P/E10WS/
Camera .......................................................................... 14
4
Table of Contents
Overview
Using the CD-ROM
Manual
The CA-590/590P Camera Adaptor attaches to the BVP-
E10/E10P/E10WS/E10WSP/E30/E30P/E30WS/E30WSP
Color Video Camera to allow the connection of a CCU-
550D/550DP/590/590P/700A/700AP/790/790P Camera
Control Unit through a triax cable.
The supplied CD-ROM includes versions of the Operation
Manuals for the CA-590/590P, CCU-590/590P, and CCU-
1)
790/790P in PDF format.
1)Available languages: Japanese (CA-590 and CCU-590 only),
English, French, German, Italian, and Spanish
The CA-590/590P has the following features:
Component signal transmission system
The CA-590/590P transmits a component signal (Y/R–Y/
B–Y) through a triax cable.
Preparations
The following program must be installed on your computer
in order to read the operation manuals contained on the
CD-ROM.
Low power consumption
An AC/DC converter of higher efficiency than the previous
model has reduced power consumption to about 8 W
(within the CA-590/590P).
• Adobe Reader Version 6.0 or higher
If Adobe Reader is not installed, you can download it from
the following URL:
Anti-electrical shock function
The high-voltage supply from the CCU (camera control
unit) is cut when the triax cable is not completed
connected.
Adobe and Adobe Reader are trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
Variety of input/output connectors
The CA-590/590P is equipped with the following
connectors:
• DC power input/output connector
• Input connector for remote-switching of return video 1,
2, 3, and 4
• Prompter signal/external sync signal input connector
• RCP connector
Reading the CD-ROM manual
To read the operation manual contained on the CD-ROM,
do the following.
1
Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your browser.
If it does not appear automatically in the browser,
double-click on the index.htm
• INCOM connector (2)
• AUDIO (LINE/MIC switch available) input connector
(2)
file on the CD-ROM.
• PROMPTER/RETURN video output connector
• EARPHONE jack
• TRACKER connector
2
Select and click on the operation manual that you
want to read.
This opens the PDF file of the operation manual.
Note
Memo
Production of some of the peripherals and related devices
described in this manual has been discontinued. For advice
about choosing devices, please contact your Sony dealer or
a Sony sales representative.
The files may not be displayed properly, depending on the
version of Adobe Reader.
In such a case, install the latest version you can download
Note
If you have lost or damaged the CD-ROM, you can
purchase a new one to replace it. Contact your Sony
service representative.
Overview / Using the CD-ROM Manual
5
Function and Location of Parts and Controls
a TALLY lamp and TALLY switch
CA-590P
s LEVEL switch
b RET 1 button, RET button and RET 2/3/4 switch
Not used.
CA-590
t PGM1/2
controls
c LIGHT switch
u TRACKER
control
d PGM 1/2 level controls
v ENG control
w PROD
control
e Triax connector
f INCOM level controls, PROD/
ENG switches, and MIC LEVEL
switches
Not used.
x MIC switches
g INCOM 1/2 connectos
h TRACKER connector
i DC IN connector
p EARPHONE jack
j RETURN connector
o RET CTRL connector
k PROMPTER connector
n REMOTE connector
l DC OUT connector switch
m AUDIO IN CH 1/2 connectors, FRONT/REAR/LINE
switches, and MIC +48V/OFF/ · switches
q CALL button
r POWER switch
Function and Location of Parts and Controls
6
a TALLY lamp and TALLY switch
OFF/REAR: Turns off the intercom microphone. Turn
the intercom microphone on and off using the control
on the external equipment connected to the RET
CTRL connector. Adjust the intercom reception level
with the INCOM level control.
OFF/FRONT: Turns off the intercom microphone. Turn
the intercom microphone on and off using the control
on the external equipment connected to the RET
CTRL connector or the VTR S/S switch on the video
camera. Use the control on the video camera to adjust
the intercom reception level. Depending on the video
camera, intercom reception level adjustment requires
menu operation.
When the TALLY switch is ON, the TALLY lamp lights
when a red tally signal, green tally signal, or call signal is
input from the CCU.
Turning the S101 switch on the internal AU-294 board to
ON mixes and outputs the battery alarm signal to the
TALLY lamp.
b RET 1 button, RET button and RET 2/3/4 switch
RET1 (return video 1) button
While this button is pressed down, the return video1 signal
from the CCU (camera control unit) can be monitored in
the viewfinder or on a monitor connected to the RETURN
connector.
g INCOM (intercom) 1/2 connectos
Connect headsets to enable the reception of program/
intercom audio and transmission of intercom audio.
Set the S3 switch on the internal MA-128 board to “CM”
when using headsets with a carbon-type microphone, and
set it to “DYN” when using headsets with a dynamic-type
microphone.
RET (return video) button
While this button is pressed down, the return video signal
from the CCU can be monitored in the viewfinder. Select
the monitored signal with the RET 2/3/4 switch.
RET 2/3/4 switch
Selects the return video signal to be monitored in the
viewfinder while the RET button is pressed down.
The INCOM 1 connector can be used for communications
through the engineer’s line even though the power to the
camera is turned off on the CCU-550D/550DP/590/590P/
700A/700AP/790/790P.
c LIGHT switch
Turns the backlight on the upper part of the panel and the
light on the connector section on or off. Depending on the
switch position, both lights turn on, only the light on the
connector section turns on, or both lights turn off.
h TRACKER connector (10-pin)
Used for communications with a tracker and intercom 1
and 2 communications. Also outputs the up tally and
program audio signals. The maximam current output from
this connector is 500 mA. Settings regarding the input/
output signals can be made on the internal AU-294 board.
d PGM (program audio) 1/2 level controls (for the
CA-590)
These controls adjust the audio volume of the program.
PGM level controls are provided for both intercom 1 and 2.
i DC IN (direct current input) connector (4-pin)
Connects an AC adapter or battery case. Supplies power
to the CA-590/590P when the POWER switch is set to
EXT.
e Triax connector
Connects a CCU-550D/550DP/590/590P/700A/700AP/
790/790P Camera Control Unit through a triax cable.
j RETURN (return video output) connector (BNC
f INCOM level controls, PROD/ENG switches, and
type)
MIC LEVEL switches (for the CA-590)
Outputs the return video signal.
INCOM (intercom) level controls
These controls adjust the audio reception level of the
intercom 1/2.
k PROMPTER (prompter video signal input/output)
connector (BNC type)
Inputs and outputs a prompter video signal. Use the S301
switch on the DM-139 internal board to select the
transmission direction (input or output) of the prompter
video signal. When the setting is made on the camera
adaptor, the transmission direction must be also changed
on the CCU.
PROD/ENG (producer/engineer) switches
Select the line for the microphone of the intercoms
connected to the respective INCOM connectors.
PROD: Selects the producer’s line.
ENG: Selects the engineer’s line.
MIC/LEVEL (microphone/intercom level) switches
The MIC and LEVEL settings specify the following
functions:
ON/REAR: Turns on the intercom microphone. Adjust
the intercom reception level with the INCOM level
control.
l DC OUT (direct current output) connector (4-pin)
Outputs a direct current of 10.5 V to 17 V at a maximum
rated current output of 1.5 A. Connecting equipment with
a power consumption greater than the maximum rating
will activate the protection circuit, cutting off the current
flow.
Function and Location of Parts and Controls
7
m AUDIO IN CH 1/2 connectors, FRONT/REAR/
q CALL button
LINE switches, and MIC +48V/OFF/• switches
Use this button to call the CCU or MSU (master setup unit)
operator. When this button is pressed, the red tally lamps
in the viewfinder and on the CCU or MSU light up.
AUDIO IN (audio input) CH 1/2 connectors (XLR type,
3-pin)
These connectors input external audio signals.
r POWER switch
Selects the power supply.
CCU: Power is supplied from the CCU.
OFF: Standby mode.
FRONT/REAR/LINE (audio signal selection) switches
These switches make settings for the respective audio
signals input from the AUDIO IN CH 1/2 connectors.
FRONT: Selects the audio input from the video camera as
the audio signal.
EXT: Power is supplied from the DC IN connector.
s LEVEL (intercom level) switch (for the CA-590P)
Selects the reception level adjustment method for the
intercoms connected to the INCOM 1/2 connectors.
REAR: Select this position to adjust the reception level of
the intercoms using the PGM1/2 controls, TRACKER
control, ENG control, and PROD control
REAR: Outputs the audio signal input from the AUDIO
IN connector to the CCU. Gain control setting for the
connected microphone must be made on the CCU.
LINE: Sets the level for the signal input from the AUDIO
IN connector to –20 dB.
MIC +48V/OFF/• (microphone power supply mode)
switches
The following power supply settings can be specified for
independently.
FRONT: When this position is selected, audio volume of
the program, reception level of the intercom connected
to the TRACKER connector, and the reception level of
the engineer's line and the producer's line are adjusted
at one operation using the control on the video camera.
the external microphone:
MIC +48V: +48 V is supplied to the external microphone
through the AUDIO IN connector. Set to this position
when the microphone requires +48 V of power supply.
OFF: No power is supplied through the AUDIO IN
connector.
• : +12 V is supplied to the external microphone through
the AUDIO IN connector. Set to this position when the
microphone requires +12 V of power supply. This
position becomes selectable when the S2 switch on the
MA-128 internal board is set to ON (page 9).
t PGM1/2 controls (for the CA-590P)
These controls adjust the audio volume of the program.
PGM1 control adjusts the program audio input from the
INCOM1 connector and the PGM2 control adjusts the
program audio input from the INCOM2 connector.
u TRACKER control (for the CA-590P)
Adjusts the reception level of the intercom connected to
the TRACKER connector.
Note
Supplying power whose voltage does not match the
requirement to the microphone may damage the
microphone. Be sure to set the MIC +48V/OFF/• switches
to match the power requirement of the microphones.
v ENG (engineer) control (for the CA-590P)
Adjusts the reception level of the engineer's line.
w PROD (producer) control (for the CA-590P)
Adjusts the reception level of the producer's line.
n REMOTE connector (8-pin)
Connects an RCP-750/751/920/921 Remote Control Panel
or RM-B150 Remote Control Unit. Connection must be
made with a cable of 150 feet (50 meters) or less in length.
x MIC (microphone level) switches (for the CA-590P)
Select the connection line of the intercom microphone
independently for the intercoms connected to the INCOM
1/2 connectors.
PROD: Connects the intercom microphone to the
producer's line.
Notes
• The REMOTE connector cannot be used when a CCU is
connected.
• When connecting the RM-B150, use the cable supplied
with the RM-B150.
ENG: Connects the intercom microphone to the
engineeer's line.
OFF: Cuts the intercom microphone connection.
o RET CTRL (return control) connector (6-pin)
Inputs the control signal for selecting the return video and
for turning the intercom microphone on and off.
p EARPHONE jack (mini-jack)
Connects an earphone for monitoring the audio from the
intercom or the program. Select the audio source with the
S251 and S252 switches on the internal AU-294 board.
Function and Location of Parts and Controls
8
Internal Boards and Switch Settings
Note
To reduce the risk of electric shock, fire or injury, do not open the cabinet. To adjust the internal settings, refer to qualified
service personnel.
MD-132 board (no switches)
a TR-132 board
b MA-128 board
c AU-294 board
CA-590/590P
Unscrew the four screws.
d DM-139 board
e MB-1019 board
CA-590/590P
Unscrew the four screws.
Internal Boards and Switch Settings
9
A S1 switch
Available in near future. Set this switch to OFF.
a TR-132 board
A S1 switch
S1
b MA-128 board
qs S15 switch
H S8 switch
C S3 switch
D S4 switch
F S6 switch
E S5 switch
G S7 switch
J S11/S12 switches
K S13/S14 switches
B S2 switch
I S10 switch
A S1 switch
A S1 switch
Available in near future. Set this switch to OFF.
– : Sets the gain 6 dB below the standard level.
Normally, set this switch to 0.
B S2 switch
F S6 switch
Set to ON only when supplying AC power to the
microphones connected to the AUDIO IN CH 1/2
connectors. Normally, set this switch to OFF.
When set to ON, the audio signals input from the AUDIO
IN CH 1/2 connectors are mixed to the imtercom audio and
output to the INCOM 1 connector. This switch is factory-
set to OFF.
C S3 switch
Set according to the microphone type of the headset
connected to the INCOM 1 connector.
DYN: Dynamic-type microphone
CM: Carbon-type microphone
G S7 switch
When set to ON, the audio signal input from the
TRACKER connector is mixed to the imtercom audio and
output to the INCOM 1 connector. Normally, set this
switch to OFF (center position).
D S4 switch
Set to ON when an unbalanced-type headset is connected
H S8 switch
to the INCOM 1 connector.
Specifies whether the VR of the INCOM 1 is used for
serial mix or parallel mix. Normally, set this switch to OFF.
E S5 switch
Sets the gain for the headset connected to the INCOM 1
I S10 switch
connector.
This switch is used for the intercom system connected to
the INCOM 1 connector. Normally, set this switch to
NORM.
+ : Sets the gain 6 dB above the standard level.
0 : Standard level.
Internal Boards and Switch Settings
10
J S11/S12 switches
These switches select the audio to be mixed with the audio
Switch
Audio to be mixed
Normal setting
S13-1
S13-2
S13-3
S13-4
S14
Audio from INCOM 1 OFF
Audio from INCOM 2 OFF
output to the INCOM 1 connector.
Switch
Audio to be mixed
Normal setting
Program audio 1
Program audio 2
Tracker audio
ON
S11-1
S11-2
S11-3
S11-4
S12
Audio from INCOM 1 ON
ON
Audio from INCOM 2 OFF
OFF
Program audio 1
Program audio 2
Tracker audio
OFF
OFF
ON
When a one ear headset is used, set the S13-1 and S13-2
switches to ON.
When a one ear headset is used, set the S11-3 and S11-4
switches to ON.
L S15 switch
Set according to the broadcast system.
OFF: NTSC (for the CA-590)
ON: PAL (for the CA-590P)
K S13/S14 switches
These switches select the audio to be mixed with the
program audio output to the INCOM 1 connector.
c AU-294 board
A S3 switch
J S201 switches
B S4 switch
S201
S101
C S5 switch
I S101 switch
D S7 switch
S7
S251
S252
S253
E S8 switch
K S251/S252 switches
S8
L S253 switches
S13
S14
S11
S12
H S13/S14 switches
G S11/S12 switches
F S10 switch
A S3 switch
output to the INCOM 2 connector. Normally, set this
switch to OFF (center position).
Set according to the microphone type of the headset
connected to the INCOM 2 connector.
DYN: Dynamic-type microphone
E S8 switch
CM: Carbon-type microphone
Specifies whether the VR of the INCOM 2 is used for
serial mix or parallel mix. Normally, set this switch to OFF.
B S4 switch
Set to ON when an unbalanced-type headset is connected
F S10 switch
to the INCOM 2 connector.
This switch is used for the intercom system connected to
the INCOM 2 connector. Normally, set this switch to
NORM.
C S5 switch
Sets the gain for the headset connected to the INCOM 2
connector.
G S11/S12 switches
+ : Sets the gain 6 dB above the standard level.
0 : Standard level.
These switches select the audio to be mixed with the audio
output to the INCOM 2 connector.
– : Sets the gain 6 dB below the standard level.
Normally, set this switch to 0.
Switch
Audio to be mixed
Normal setting
S11-1
S11-2
S11-3
Audio from INCOM 1 OFF
Audio from INCOM 2 ON
D S7 switch
When set to ON, the audio signal input from the
Program audio 1
OFF
TRACKER connector is mixed to the imtercom audio and
Internal Boards and Switch Settings
11
Switch
Audio to be mixed
Program audio 2
Tracker audio
Normal setting
OFF
OFF
Switch
S253-4
Audio to be output
S11-4
S12
Program audio 2
d DM-139 board
When a one ear headset is used, set the S11-3 and S11-4
switches to ON.
A S301 switch
H S13/S14 switches
These switches select the audio to be mixed with the
S1
S2
B S302 switch
program audio output to the INCOM 2 connector.
Switch
Audio to be mixed
Normal setting
S13-1
S13-2
S13-3
S13-4
S14
Audio from INCOM 1 OFF
Audio from INCOM 2 OFF
Program audio 1
Program audio 2
Tracker audio
ON
ON
OFF
When a one ear headset is used, set the S13-1 and S13-2
switches to ON.
A S301 switch
Selects the direction of the prompter signal flow. The
signal flow direction must also be changed on the CCU.
RX: The video signal from the CCU is output from the
PROMPTER connector (factory-setting).
I S101 switch
Selects the item to be mixed with the battery alarm signal.
REM: Available in near future.
Switch
S101-1
Item to be mixed
Normal setting
TX: The video signal input to the PROMPTER connector
is output to the CCU. Note that the CCU-550D/550DP
does not support this function.
Battery alarm signal ON
S101-2
S101-3
TEMP
OFF
OFF
FAN STOP
B S302 switch
Selects the signal to be output from the PROMPTER
connector.
PROMPT: Prompter video signal is output (factory-
setting).
RET: Return video signal is output.
J S201 switches
Sets the talk level through the TRACKER connector.
– 20: Decreases the level by 20 dB.
0 : Standard level.
Normally, set this switch to 0.
K S251/S252 switches
These switches select the audio to be output to the
EARPHONE jack.
e MB-1019 board
Switch
S251-1
Audio to be output
Audio from INCOM 1
A S1 switch
B S2 switch
S251-2
S251-3
S251-4
S252
Audio from INCOM 2
Program audio 1
Program audio 2
Not used.
S301
S302
L S253 switches
These switches select the audio to be output to the
TRACKER connector.
Switch
S253-1
Audio to be output
Audio from INCOM 1
S253-2
S253-3
Audio from INCOM 2
Program audio 1
Internal Boards and Switch Settings
12
A S1 switch
Selects the signal to be output to the RETURN connector.
RET: Return video signal is output (factory-setting).
MONI: Monitor video signal is output.
VBS: Composite video signal is output.
B S2 switch
Selects the signal to be input/output from the PROMPTER
connector.
PROMPT: Prompter video signal is input and output
(factory-setting).
REF: Reference signal for the video camera is input.
Internal Boards and Switch Settings
13
Preparations
Attaching the CA-590/590P to a BVP-E10/E10P/E10WS/E10WSP/E30/E30P/
E30WS/E30WSP Color Video Camera
When you attach the CA-590/590P to a BVP-E10/E10P/E10WS/E10WSP/E30/
E30P/E30WS/E30WSP Color Video Camera as shown below, the 68-pin
connectors on both units are automatically connected.
1
Attach the CA-590/590P to the rear of the color video camera.
Hook the upper part, then push the lower part in until it snaps into place.
2
Tighten the screw with a coin.
Tighten the screw.
Removing a Camera Adaptor
Loosen the screw on the video camera until it stops, then remove the camera
adaptor while pushing the screw.
14
Preparations
Loosen the screw on the video
camera until it stops, then push it.
Securing the triax cable to the camera adaptor
1
Attach the supplied cable holder with the supplied two M3 × 6 screws.
M3 × 6 screws (supplied)
Cable holder
(supplied)
2
Route the triax cable as illustrated below, then fasten the cable holder
around the cable.
cable
15
Preparations
Removing the cable from the cable holder
Pull
Lift to release
16
Preparations
Connections
Connectable equipment
BVF-55/55CE 5-inch Viewfinder
CCU-700A/700AP/790/790P
Camera Control Unit
To the CAMERA
connector
CCU-550D/550DP/590/590P
Camera Control Unit
To the triax
connector
Triax cable
RM-B750 Remote
Control Unit
To the REMOTE
connector
Camera cable
To the DC IN
connector
AC-DN10 AC
Adaptor
To the DC OUT
connector
RCP-750/751/920/921 Remote
Control Panel
DC cord
To supply power from the DC connector
Set the POWER swicth to EXT.
Power supply
When a Camera Control Unit is connected
Set the POWER switch to CCU to supply power to the CA-
590/590P from the CCU.
Connections
17
For the BVP-E30/E30P/E30WS/E30WSP whose
camera software version is 1.03 or later
Self-Diagnostics
When the CA-590/590P is connected to the BVP-E10/
E10P/E10WS/E10WSP/E30/E30P/E30WS/E30WSP, you
can display the results of self-diagnostics of the CA-590/
590P internal boards using the DIAGNOSIS menu of the
video camera. The self-diagnostics results can be
monitored on the camera's viewfinder.
Displaying the DIAGNOSIS menu
Self-diagnostics results of the CA-590/590P
internal boards
Refer to the Operating Instructions supplied with the video
camera.
CA-590: Model name of the CA
MD: Status of the internal MD board
AU: Status of the internal AU board
TR: Status of the internal TR board
MA: Status of the internal MA board
FAN: Status of the fan on the CA power unit
The contents of the self-diagnostics
results
For the BVP-E10/E10P/E10WS/E10WSP or for the
BVP-E30/E30P/E30WS/E30WSP whose camera
software version is earlier than 1.03
Self-diagnostics results of the CA-590/590P
internal boards
CA-570: Model name of the CA (appears as "CA-570"
even when the CA-590/590P is connected).
MD: Status of the internal MD board
AU: Status of the internal AU board
TR: Status of the internal TR board
When an abnormality is detected, "NG" appears for the
corresponding internal board.
When an abnormality is detected on the fan of the CA
power unit, "- -" and "NG" alternate on all the internal
board status indications.
And when "NG" appears on all the internal board status
indications, an abnormality may have occurred on the CA
power unit.
Note
The camera software upgrade can be done only on the
BVP-E30/E30P/E30WS/E30WSP.
Self-Diagnostics
18
Design and specifications are subject to change without
notice.
Specifications
Note
Always verify that the unit is operating properly before
use. SONY WILL NOT BE LIABLE FOR DAMAGES
OF ANY KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR REIMBURSEMENT ON
ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY
PERIOD OR AFTER EXPIRATION OF THE
WARRANTY, OR FOR ANY OTHER REASON
WHATSOEVER.
General
Power consumption
8 W (within the CA-590/590P)
Operating temperature
–20°C to +45°C (–4°F to +113°F)
Storage temperature
–20°C to +50°C (–4°F to +122°F)
120 × 211 × 202 mm (w/h/d)
Dimensions
Mass
3
3
(4 / × 8 / × 8 inches)
4
8
2.8 kg (6 lb 3 oz)
Input/output connectors
AUDIO IN CH 1/2 (2ch)
XLR type 3-pin, Female, 600 ohms,
balanced
DC IN
DC OUT
RETURN
PROMPTER
RET CTRL
EARPHONE
CAMERA I/F
CCU
XLR type, 4-pin, DC 10.5 to 17 V
4-pin, DC 10.5 to 17V, Max. 1.5 A
BNC type, 1Vp-p, 75 ohms
BNC type, 1Vp-p, 75 ohms
6-pin
Mini-jack, 8 ohms
68-pin
Triax
∗
INCOM 1/2 (2ch)
XLR type, 5-pin, Female
REMOTE
8-pin
TRACKER
10-pin
∗ When a 5-inch viewfinder is connected to this unit or the
TRACKER connector or the REMOTE connector is used, the
maximum 1.5 A DC output cannot be obtained from the DC OUT
connector.
Supplied accessories
Carrying belt (1)
Cable holder (2)
M3 × 6 screws (4)
Operation Manual (1)
CD-ROM (1)
Optional accessories
CAC-6 Return Video Selector
BVF-55/55CE Viewfinder
RM-B750 Remote Control Unit
Specifications
19
The material contained in this manual consists of information
that is the property of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use thereof for any purpose other
than the operation or maintenance of the equipment described
in this manual without the express written permission of Sony
Corporation.
CA-590/590P
(UC/CE)
Printed in Belgium
2007.04.08
© 2005
Sony Corporation
3-869-644-02 (1)
|