Rosen Entertainment Systems DVD Player R5505 User Guide

RO SEN  
a new generation of leadership in mobile video  
video  
R5505 DVD/CD/MP3 Player w/ TV Tuner  
R5506 DVD/CD/MP3 Player  
Owner's Manual and Installation Guide  
R
.mp3  
T
R
 
Warning!  
Table of Contents  
THE R5505/R5506 DVD/CD/MP3 PLAYERSARE DESIGNED TO  
ENABLE VIEWING OF DVD OR CD-VIDEO RECORDINGS ONLY  
FOR REAR-SEAT OCCUPANTS.  
Introduction ...................................................................... 2  
Care and Maintenance ..................................................... 3  
Discs Played by this unit ................................................... 4  
Using the DVD player ........................................................ 5  
The Remote Control .......................................................... 7  
DVD/VCD/CD-Audio Playback .......................................... 8  
Watching Broadcast Television (R5505 only)................. 10  
MP3 Playback on CD-R discs .......................................... 11  
Installation and Wiring.................................................... 12  
Setup ............................................................................... 16  
Troubleshooting .............................................................. 16  
MOBILE VIDEO PRODUCTS ARE NOT INTENDED FOR VIEW-  
ING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION.  
SUCH USE MAYDISTRACT THE DRIVER OR INTERFERE WITH  
THE DRIVER’S SAFE OPERATION OF THE VEHICLE,AND  
THUS RESULT IN SERIOUS INJURY OR DEATH. SUCH USE  
MAYALSO VIOLATE STATE LAW.  
ROSEN ENTERTAINMENT SYSTEMS DISCLAIMSANYLIABIL-  
ITYFORANYBODILYINJURYOR PROPERTY DAMAGE THAT  
MAYRESULT FROMANY IMPROPER OR UNINTENDED USE.  
About Installation  
Installation of mobile audio and video components requires  
experience with a variety of mechanical and electrical proce-  
dures. Even though this manual provides general installation  
and operation instructions for your new, it does not show the  
exact installation methods for your particular system or  
vehicle.  
If you do not have the required knowledge and experience to  
successfully complete the installation, we strongly recommend  
consulting an authorized Rosen/necvox dealer about profes-  
sional installation options.  
 
Note:  
The R5505 and R5506 are designed to be components in a full  
INTRODUCTION  
audio/video system. If you have any questions about compatible  
components, such as monitors, FM modulators, or other audio/  
video products, contact your authorized Rosen/necvox dealer.  
The R5505 and R5506 are full-featured disc players, support-  
ing DVD, CD-Video, CD-Audio, and MP3 playback, and are  
designed specifically for the mobile environment. They are  
intended for use with other Rosen/necvox products and  
Rosen/necvox video monitors, and can also be integrated  
with many other products as part of a complete mobile video  
solution. With a digital audio output, they can also support  
use of optional digital audio processors. These DVD players  
incorporate many different video output settings to allow the  
best possible viewing experience, regardless of what type of  
video monitor you may be using.  
Accessories Supplied  
Infrared (IR) remote control  
External IR Receiver for optional applications  
Power-supply harness and RCA audio and video cables  
Assorted mounting hardware  
This Owner’s Manual / Installation Guide  
The R5505 and R5506 play DVD discs in PAL or NTSC  
formats (NTSC is the standard North American video format),  
CD-Audio discs, and CD-recordable discs with MP3 files. For  
more details on disc types supported, please see “Discs  
Played by the Unit”  
About the Registered Marks  
This product incorporates copyright protection technology that  
is protected by method claims of certain U.S. patents and  
other intellectual property rights owned by Macrovision  
Corporation and other rights owners. Use of this copyright  
protection technology must be authorized by Macrovision  
Corporation, and is intended for home and other limited  
viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is prohib-  
ited.  
The remote control (included) provides access to the full set  
of standard DVD functions, such as subtitle control, digital  
freeze-frame viewing, viewing from multiple camera angles,  
selection of various language audio soundtracks, and digital  
playback at fast or slow speeds.  
Manufactured under license from Dolby Laboratories. Dolby  
and the double-D symbol are trademarks of Dolby Laborato-  
ries.  
4
R5505  
 
FCC Approval  
CARE AND MAINTENANCE  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interfer-  
ence to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to consult the  
dealer or an experienced radio/TV technician for help.  
Handling Discs  
Always handle a disc by its edges. Never touch the surface of  
the disc directly. To remove inadvertent fingerprints and dust,  
use a soft cloth and wipe in a straight line from the center of  
the disc to the outside edge. Never use liquid or aerosol  
cleaners, anti-static spray, or thinner to clean the disc surface.  
Do not place discs in the following places: direct sunlight; dirty,  
dusty and damp areas; near car heaters; on the seats or  
dashboard. Avoid using adhesive labels on discs.  
Liquids and the DVD player  
Keep all liquids, including beverages and cleaning liquids,  
away from the DVD player. Liquids inside the player can  
damage the electronics, and result in electrical shock or fire.  
If the unit or the remote control should become wet, turn off all  
power and contact an authorized Rosen/necvox dealer to  
have the system inspected.  
Servicing the DVD player  
This unit uses a precision mechanism. In the event that  
trouble arises, never open the case, disassemble the unit, or  
lubricate the rotating parts.  
R5505  
5
 
Do not attempt to open the unit or the remote control. The  
internal parts are not serviceable by the user. Opening any of  
the components will void the warranty. THIS IS A CLASS I  
LASER PRODUCT, USING A LASER WHICH COULD CAUSE  
HAZARDOUS RADIATION EXPOSURE IF IMPROPERLY  
DISASSEMBLED. All service should be performed by autho-  
rized Rosen service centers or other qualified service  
personnel.  
DISCS PLAYED BY THE UNIT  
Discs Compatible with the R5505 and R5506  
DVD, Video CD (VCD), CD/CD-R, and MP3 discs are compat-  
ible with the unit. The identifying logo and description of each  
disc type is given below.  
CAUTION!  
Changes or modifications to this product not  
approved by the manufacturer will void the  
warranty and will violate FCC approval.  
DVD  
12 cm disc/8 cm disc  
(single-sided disc only)  
Temperature and Moisture  
Video CD  
12 cm disc/8 cm disc  
If the player is used while the interior of the vehicle is very  
cold, condensation may form on the disc or on the internal  
optical pickup system and prevent proper playing of the disc. If  
you suspect that condensation is an issue, eject the disc and  
inspect the playing surface. If necessary, remove the conden-  
sation with a clean soft cloth as described above. If you still  
experience problems with playback, you will need to wait for  
approximately one hour to allow the DVD player to warm up,  
and for the condensation to evaporate. If playback issues  
continue, please see your authorized Rosen/necvox dealer.  
CD/CD-R, MP3 12 cm disc/8 cm disc  
DVD Regions  
This digital media player is designed and manufactured to  
respond to the Region Management Information that is  
recorded on a DVD disc. If the Region number described on  
6
R5505  
 
the DVD disc does not correspond to the Region number of  
this player (Region 1), this player will not be able to play the  
DVD disc. Some DVD discs are manufactured to operate in  
“all” zones, and those discs are compatible with this DVD  
player.  
USING THE DVD PLAYER  
In order to operate the player, the vehicle ignition key switch  
must be in the ACC or engine ON position.  
Region Icons:  
ACC or engine  
ON position  
1
4
ALL  
1
6
WARNING!  
To prevent the battery from going dead,  
operate this unit with the engine  
running, if possible.  
Discs Incompatible with the R5505 and R5506  
The following disc types are incompatible:  
DVD-ROM  
DVD-R/DVD-RW/DVD-RAM  
Photo CD  
CD-ROM (Excluding most CD-Recordable discs using MP3  
or CD-A formats)  
CD-Audio manufactured with certain copy protection  
methods  
Any DVD with a Region number other than “1” and “ALL”  
R5505  
7
 
Front-Panel Controls  
The [POWER] button turns the DVD player on and off. The  
[POWER] button on the remote can also turn on the unit.  
1
2
The [OPEN/CLOSE] button operates the disc loading drawer.  
3
For information on using the rest of the front-panel controls,  
please see the sections describing disc playback.  
4
The front-panel display provides basic information about the  
status of the DVD player. Please note that essential informa-  
tion about using the unit will be displayed on the video screen  
connected to the unit, and initial setup of the DVD player  
cannot be completed without an operating video monitor  
providing this on-screen display of menus and settings.  
Whenever the term “on-screen display” is used, it refers to the  
video monitor display, not the front panel display.  
5
6
7
DTS  
surround  
icon  
1
2
3
4
5
6
7
Disc loading drawer  
Front-panel display  
[POWER] button  
Angle  
mark  
icon  
Play/  
Pause  
icon  
VCD  
icon  
Dolby  
surround  
indicator  
Playback  
Control  
indicator  
DVD  
icon  
[PLAY/PAUSE] button  
[STOP] button  
MP3  
icon  
Disc  
status  
indicator  
[OPEN/CLOSE] button  
A/V auxiliary inputs  
Repeat  
status  
icons  
Numeric display  
8
R5505  
 
Using the Remote Control  
THE REMOTE CONTROL  
Aim the remote control towards the IR receiver on the front  
panel. The remote control can operate at a 30-degree angle  
from the front of the unit.  
Power  
Open/Close  
A-B  
Source -  
DVD/TV/EXT  
If you try to perform an action that is not permitted at the  
moment, the DVD playerdisplays the following symbol on the  
screen:  
Scan  
Surround  
Display  
Angle  
Zoom  
Volume  
Audio  
Next /Previous -  
SKIP  
Subtitle  
Mute  
Setup  
Menu  
Equalizer  
Title Menu  
This is typically displayed if a key is pressed during disc  
loading or ejecting, during the introduction section of a disc,  
or if you attempt to access certain sections of the Setup menu  
while the disc is in Play, Pause, or pre-stopmode. Also, this  
symbol will be displayed whenever the loaded DVD disc  
disallows the attempted action.  
Enter/Play  
Navigation  
keys  
Slow  
Stop  
Fast  
Pause/Step  
Numeric  
keypad  
R5505  
9
 
Disc Playback  
DVD/VCD/CD-AUDIO PLAYBACK  
DVD playback will often begin automatically when the disc is  
inserted. With some DVD discs, you will need to press  
[ENTER/PLAY] to begin playback.  
Inserting a DVD/VCD/CD  
1 Turn the vehicles ignition key to the ACC or ON position.  
CD-Audio discs will begin playback automatically.  
ACC or engine  
ON position  
CDs with MP3 files may require you to navigate the file  
structure menu. For more information, see “MP3 Playback.”  
2 Press either the [POWER] button on the front panel or the  
[POWER] button on the remote control.  
Stopping Playback  
There are two ways to stop playback:  
3 Press the [OPEN/CLOSE] button. Remove any disc already  
in the tray, and gently place a disc in the tray label-side up.  
Pressing [STOP] once will stop playback, and the DVD  
player will store the location last played on the disc.  
Playback can be resumed at the same point on the disc by  
pressing [PLAY].  
4 Press [OPEN/CLOSE] or [PLAY].  
Pressing [STOP] twice will stop playback and clear the  
R5505 s memory of the last point played on the disc.  
Pressing [PLAY] at this point will cause the DVD player to  
begin playback from the beginning of the disc.  
10  
R5505  
 
Selecting a Track or Chapter  
Repeat Mode  
Press the [REPEAT] button to select from the following repeat  
Moving to the Next Track or Chapter  
modes:  
Press the [SKIP forward] button during playback. The next  
track or chapter will be selected.  
Repeat 1 - Repeat - Repeat Off.  
Moving to the Previous Track or Chapter  
With DVD playback, pressing the [REPEAT] button once  
causes the current chapter to be replayed. Pressing it twice  
enables the DVD disc to be continuously replayed.  
Press the [SKIP back] button during playback. The first time  
this button is pressed, playback of the current track or chapter  
will restart from the beginning. Pressing this button again will  
cause the previous track or chapter to be played.  
With CD playback, pressing the [REPEAT] button once  
causes the current track to be replayed. Pressing it twice  
enables the disc to be continuously replayed.  
Fast Searching During Playback  
Viewing Angles  
Press [ ] and [ ] during playback to rapidly search for a  
particular section of a DVD or CD. Each time a fast-search  
button is pressed, the speed of the fast search changes as  
follows:  
The Angle Mark appears on the front-panel display and on the  
on-screen display during scenes that offer multiple viewing  
angles. (Not all DVD discs support this function.) Use the  
[ANGLE] button to select from the various angles available. To  
conceal the Angle Mark, please see the Setupsection.  
Standard Speed – 2X Standard Speed – 4X – 6X – 8X – Back  
to Standard Speed.  
Pausing Playback  
Press [PLAY/PAUSE] - disc playback will pause, and the  
frame being displayed will remain on the screen. Press  
[PLAY/PAUSE] again to return to normal playback.  
R5505  
11  
 
Parental Control  
WATCHING BROADCAST TELEVISION  
Parental Control allows authorized users to select an upper  
limit to film ratings that can be played. If a DVD is inserted that  
exceeds that rating, the following screen appears:  
Using the TV Tuner in the R5505  
The R5505 has a built-in TV tuner. With an optional antenna  
(not included), broadcast television can be received and  
viewed on the monitor connected to the R5505.  
INPUT PASSWD:  
The parental setting of this  
The parental setting of this  
player prohibits play.  
player prohibits play.  
Use the [DVD/TV/EXT] button to select TV. Use the [ ] and  
Would you like this disc to play?  
Would you like this disc to play?  
[ ] buttons to change channels.  
YES  
YES  
NO  
YES  
NO  
Use the [REP/SCAN] button to scan the stored stations.  
Use the [A-B/SAV/ERS] button to store stations, and to erase  
stations which have been stored.  
In order for the film to play, the viewer must select Yes,and  
then the four-digit numeric passwordmust be entered.  
Note:  
Television reception is greatly influenced by terrain, atmospheric  
conditions, and the location of the receiver. When viewing  
broadcast television in a moving vehicle, various types of  
interference are often experienced. This is inherent in the nature  
of analog broadcast television (and why cable was invented!).  
The factory default password is 3308. The password can be  
changedsee section “Setup.” The film ratings allowed are  
also selected in the “Setup” section.  
Notes:  
To change the film rating setting, the password must be used.  
The DVD player determines the correct film ratings to use based  
on the country selected in the “Locale” setting —see section  
Setup.”  
Not all DVD titles support this feature.  
12  
R5505  
 
MP3 PLAYBACK ON CD-R DISCS  
- - SMART NAVI - -  
- - SMART NAVI - -  
MP3 Disc Recording and File Extensions  
OOT  
ROOT  
(ARTIST NAME)  
MP3 (ARTIST NAME)  
0
1
1
ROOT  
0
Always add a file extension .MP3or .mp3to an MP3 file  
by using single-byte letters. If you add a different file exten-  
sion, or forget to add the file extension .MP3or .mp3,the  
file cannot be played. In addition, if you use upper case and  
lower case letters (capital and small letters) mixed together  
for file extensions, normal play may not be possible.  
(ARTIST NAME)  
MP3 (ARTIST NAME)  
(ARTIST NAME)  
MP3 (ARTIST NAME)  
2
2
3
3
ARTIST NAME - SONG TITLE  
Notes:  
Theis player cannot play back a disc recorded on a CD-RW unit.  
Some CDs recorded in CD-R mode may not be usable.  
Files without MP3 data will not play.  
Three repeat modes are available for MP3 use:  
NOREPEAT  
REP ONE repeats the current file  
FOLDER REP repeats the current folder  
MP3 Playback  
When a disc with MP3 files is inserted, the SMART NAVI  
screen will appear. Each folder and file will be shown (the  
order may be slightly different than that on your PC). Navigate  
the files and folders using the navigation arrow keys, and  
select a file or folder to be played by using the [ENTER] button.  
To move to the next file or the previous file, use the [SKIP]  
buttons.  
To conceal the SMART NAVI screen, see “Setup.”  
Supported MP3 File Formats  
ISO9660, level 1 and level 2 (the most common type of MP3  
format)  
Joliet (a version of ISO9660 that supports longer filenames)  
Romeo (a format used by some CD-creating software)  
R5505  
13  
 
Installation and Wiring  
1. Before Starting  
2. Package Contents  
Read these instructions and the following precautions  
carefully.  
Disc player unit  
IR Remote control  
WARNING!  
4-pin Power Supply harness  
RCA Audio Cable  
Additional IR Receiver (with cable)  
Installation Brackets and Assorted Hardware  
Owners Manual / Installation Guide  
Warranty Card  
Be sure to disconnect the battery (-)  
terminal before starting. This is to  
prevent short circuits during installation.  
3. Installation Requirements  
1 Use the enclosed screws for installation. Using other  
screws can cause damage and void the warranty.  
Precautions  
Chassis  
Chassis  
Damage  
This unit is exclusively for cars with a negative ground, 12V  
power supply.  
Do not open the case. There are no user-serviceable parts inside.  
If you drop anything into the unit during installation, consult your  
dealer or an authorized Rosen service center.  
Use a soft, dry cloth to clean the case. Never use a rough cloth,  
thinner, benzene, alcohol, or other solvent. For tough dirt, apply a  
small amount of cold or warm water to a soft cloth and gently  
wipe.  
14  
R5505  
 
Next, use these screws to attach the mounting brackets to the  
unit. Depending on the installation location, you will orient  
them either up or down.  
4. Installing the DVD player  
Mounting the DVD player  
WARNING!  
Always use great care when attaching  
anything to a vehicle! Visually inspect all  
sides of any potential screw location, to  
insure no damage will occur. If you have  
questions about this process, see your  
authorized Rosen dealer.  
CAUTION!  
Do not overtighten the screws on uneven  
surfaces! This can cause damage to the  
unit. If an even mounting surface can-  
not be found, fabricate a flat panel,  
mount the unit to it, and mount that  
panel to the vehicle  
First, temporarily remove the Phillips side screws from the  
unit as shown.  
Finally, attach the mounting brackets to the mounting surface  
in a safe and secure fashion.  
R5505  
15  
 
Wiring the DVD player  
Power Harness Connections  
Read the following precautions before wiring your system.  
Disconnect the negative battery terminal before making  
any wiring connections.  
Wire Color Codes  
Be particularly careful where you route wires. Keep them  
away from the engine, exhaust system, etc. Heat may  
damage wires.  
Note: Connect  
using proper fusing  
with 3A fuses.  
If the fuse should blow, make sure all connections are  
correct and no wires are damaged before replacing the  
fuse. Always use fuses that are the same amperage value  
as the original. When replacing a fuse, never let the battery  
side touch any metal part or any other wire.  
Yellow  
+12V Constant power  
Black  
- Ground  
Red  
+12V Accessory  
WARNING!  
Wire side of Power Connector  
Not all Rosen and Rosen/necvox products  
use identically-wired four-pin power  
harnesses! ONLY use the four-pin power  
harness supplied with this unit! Use of any  
other four-pin harness may cause failure  
NOT covered by the manufacturer’s  
warranty!  
Red  
+12V Accessory  
Yellow  
+12V  
Constant  
Power  
Black  
- Ground  
16  
R5505  
 
Rear Panel Connections  
Four-pin  
three-wire  
power  
harness  
connector  
Video output  
(yellow)  
TV  
antenna  
input  
(R5505  
only)  
Coaxial digital  
output  
External  
IR sensor  
input  
Left and right  
audio output  
(white = left,  
red = right)  
R5505  
17  
 
Changing Settings  
SETUP  
The following sections explain how to customize various  
features of the DVD player.  
TYPICAL SETUP AND CONFIGURATION  
To change settings:  
The DVD player is very flexible. For more advanced setting  
options, please see the Setup Options Listat the end of this  
section.  
1 Press [SETUP].  
2 Use the [ ] and [ ] buttons to highlight a selection.  
3 Press the [ENTER] button to confirm your selection.  
The unit is shipped with the following configuration:  
SETUP MENU -- MAIN PAGE  
Standard 4:3 aspect ratio format output  
Automatic NTSC/PAL output switching  
Analog stereo audio, digital audio output off  
All language options set to English  
GENERAL SETUP  
SPEAKER SETUP  
AUDIO SETUP  
PREFERENCES  
Parental control off, and default password of 3308.  
EXIT SETUP  
If you try to perform an action that is not permitted (such as  
accessing the Preferences menu while a disc is playing), the  
on-screen display will use the following symbol:  
18  
R5505  
 
Changing the Aspect Ratio Mode  
Changing the Video Output Mode  
To change the aspect ratio mode, select GENERAL, and then  
select TV DISPLAY. For widescreen (16:9) monitors, select  
WIDE. For standard monitors and letterbox viewing (black  
bars on the top and bottom of the screen, but the entire image  
preserved), select NORMAL/LB. For standard 4:3 monitors  
and a full-screen image, but with the edges variably cropped  
to fit (pan-and-scanmode), select NORMAL/PS.  
To change the video output mode, select PREFERENCES,  
and then select TV TYPE. The default is MULTI. If you experi-  
ence problems playing a PAL disc on your NTSC monitors,  
select NTSC. If you are using European-spec PAL monitors  
exclusively, select PAL.  
- - PREFERENCES PAGE - -  
TV TYPE  
- - GENERAL PAGE - -  
MULTI  
NTSC  
PAL  
SUBTITLE  
TV DISPLAY  
OP MODE  
ANGLE MARK  
OSD LANG  
NORMAL/PS  
NORMAL/LB  
WIDE  
AUDIO  
SUBTITLE  
DISC MENU  
LOCALE  
CAPTIONS  
SCR SAVER  
PARENTAL  
MAIN PAGE  
Note:  
The default “MULTI” will automatically output NTSC video from  
NTSC discs, and PAL video from PAL discs. Many video monitors  
can automatically handle either type of video signal. NTSC is the  
North American standard, and the only type of disc many North  
American users will encounter.  
R5505  
19  
 
Activating Captions and Subtitles  
Concealing the Angle Mark”  
To enable or disable captions or subtitles, select GENERAL  
and CAPTIONS.  
To display or conceal the angle mark,which appears during  
scenes that support the multiple-viewing-angle feature, select  
GENERAL and ANGLE MARK.  
Note:  
If CAPTIONS is set to OFF, the [SUBTITLE] button will be defeated  
from working. If SUBTITLE OFF is selected under Preferences –  
Audio, then the [SUBTITLE] button can still enable subtitles during  
playback, as long as CAPTIONS is set to ON.  
- - GENERAL PAGE - -  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
ANGLE MARK  
OSD LANG  
ON  
ON  
OFF  
- - GENERAL PAGE - -  
CAPTIONS  
SCR SAVER  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
MAIN PAGE  
CAPTIONS  
ON  
SCR SAVER  
OFF  
MAIN PAGE  
20  
R5505  
 
Activating the Digital Output  
Selecting an LPCM Output Frequency  
To turn on the digital output, select AUDIO and AUDIO OUT.  
To select an LPCM output frequency (when a digital audio  
processor is in use), select AUDIO and LPCM OUTPUT.  
Note:  
Only enable the digital output when a digital audio processor is  
in use, since enabling it disables the analog audio output on the  
red and white RCA jacks. Note that some digital audio proces-  
sors will require you to select an LPCM output frequency.  
-- AUDIO SETUP --  
AUDIO OUT  
OP MODE  
DUAL MONO  
DYNAMIC  
-- AUDIO SETUP --  
PRO LOGIC  
LPCM OUT  
LPCM 48K  
LPCM 96K  
AUDIO OUT  
OP MODE  
DUAL MONO  
DYNAMIC  
ANALOG  
SPDIF/RAW  
SPDIF/PCM  
MAIN PAGE  
PRO LOGIC  
LPCM OUT  
MAIN PAGE  
R5505  
21  
 
Deactivating the Smart NavOn-Screen Menu Display  
Changing Language Settings  
To play MP3 discs without the Smart Navon-screen menu  
Several language settings can be customized on the R5505.  
display, select PREFERENCES, then SMART NAV.  
Notes:  
Not all language settings are supported by all discs.  
- - PREFERENCES PAGE - -  
The languages supported by the DVD player vary by individual  
option setting.  
AUDIO  
SUBTITLE  
DISC MENU  
LOCALE  
To change the on-screen display language, select GEN-  
ERAL and OSD LANG.  
PARENTAL  
PASSWORD  
NO MENU  
SMART NAV  
DEFAULTS  
MAIN PAGE  
WITH MENU  
- - GENERAL PAGE - -  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
ENGLISH  
CHINESE  
MAIN PAGE  
22  
R5505  
 
To change the soundtrack language, select PREFERENCES  
To change the disc menu language, select PREFERENCES  
and AUDIO.  
and DISC MENU.  
- - PREFERENCES PAGE - -  
AUDIO  
- - PREFERENCES PAGE - -  
AUDIO  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
SUBTITLE  
DISC MENU  
LOCALE  
SUBTITLE  
ENGLISH  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
GERMAN  
ITALIAN  
DISC MENU  
DISC MENU  
LOCALE  
PARENTAL  
PASSWORD  
SMART NAV  
DEFAULTS  
MAIN PAGE  
PARENTAL  
PASSWORD  
SMART NAV  
DEFAULTS  
MAIN PAGE  
To change the subtitle or caption language, select PREF-  
ERENCES and SUBTITLE.  
- - PREFERENCES PAGE - -  
AUDIO  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
SUBTITLE  
DISC MENU  
LOCALE  
PARENTAL  
PASSWORD  
GERMAN  
GERMAN  
ITALIAN  
SMART NAV  
SMAR  
DEFAULTS  
MAIN PAGE  
MAIN P  
R5505  
23  
 
Setup Options List  
The factory default options are given in bold type.  
GENERAL PAGE  
(AUDIO SETUP CONTINUED)  
TV DISPLAY:  
PIC MODE:  
NORMAL/PS, NORMAL/LB, WIDE.  
LPCM OUTPUT: LPCM 48K, LPCM 96K  
AUTO, HI-RES, N-FLICKER  
PREFERENCES PAGE  
ANGLE MARK: ON, OFF  
TV TYPE:  
AUDIO:  
MULTI, NTSC, PAL  
OSD LANG:  
CAPTIONS:  
ENGLISH, CHINESE  
ON, OFF  
ENGLISH, FRENCH, SPANISH, CHINESE,  
JAPANESE  
SCRN SAVER: OFF, ON  
SUBTITLE:  
DISC MENU:  
LOCALE:  
ENGLISH, FRENCH, SPANISH, CHINESE,  
JAPANESE, OFF  
SPEAKER SETUP  
DOWNMIX:  
LT/RT, STEREO  
ENGLISH, FRENCH, SPANISH, CHINESE,  
JAPANESE  
AUDIO SETUP  
CHINA, FRANCE, HONG KONG, JAPAN,  
TAIWAN, GBR, USA  
AUDIO OUTPUT: ANALOG, SPDIF/RAW, SPDIF/PCM  
OP MODE:  
LINE OUT, RF REMOD  
PARENTAL:  
PASSWORD:  
SMART NAV:  
DEFAULTS:  
OFF  
DUAL MONO:  
DYNAMIC:  
STEREO, L-MONO, R-MONO, MIX-MONO  
OFF to FULL (eight steps)  
OFF, ON,AUTO  
3308  
ON, OFF  
PRO LOGIC:  
RESTORE FACTORY SETTINGS  
24  
R5505  
 
TROUBLESHOOTING  
SPECIFICATIONS  
Tinnysound or low-level sound.  
Supply voltage: 12V DC Nominal, 11-16V operating voltage*  
Temperature: 0o to 50o Celsius*  
Current consumption: Less than 2A  
Check the Volume setting.  
Check the Downmixsetting in the SETUP menus and  
ensure that it is set to Stereo,not LT/RT.”  
Video:  
Television System: NTSC/PAL  
Aspect ratio: 4:3, 16:9  
TV encoder resolution: 10-bit DA converter  
Video Signal level: 1V peak-to-peak  
Discs played:  
No sound  
Check the Mute function on the remote control.  
DVD video discs—  
Is the Analog audio output turned off? Check the Setup Menu  
under Audio, Audio Out. Using the Digital output defeats the  
Analog audio output.  
5(12 cm) single-sided, single and double-layer  
3(8 cm) single-sided, single and double-layer  
Compact discs (CD-DA, VIDEO-CD, CD-R)—  
5(12 cm) disc  
3(8 cm) disc  
Picture distorts, rolls, appears black and white.  
Audio output level: 2V RMS @1kHz  
Check that the TV Type setting is correct for the monitors  
being used. PAL video often rollson NTSC monitors.  
Audio signal output characteristics:  
Frequency response:  
48khz sampling : 4Hz~22khz  
96khz sampling : 4Hz~44khz  
With a widescreen 16:9 monitor, I have black bars on the  
top and bottom of my screen.  
* Note: Use of the R5505 or R5506 beyond the safe operating ranges  
listed can cause temporary or permanent damage to the unit, and such  
damage may not covered by the manufacturer’s warranty.  
Change the TV Display mode to Wide.”  
R5505  
25  
 
26  
R5505  
 
 
Please read this entire document carefully  
before operating or installing this unit.  
866-GO ROSEN  
 

QVS Switch KVM102UEC User Guide
Radio Shack Speaker System 40 1430 User Guide
Raypak Electric Heater 552 1102 User Guide
Regency Fan Regatta User Guide
RocketFish Digital Camera RF WEB2C User Guide
Roper Microwave Oven MHE14XM User Guide
Ryobi Blower RGBV3100 User Guide
Saab Automobile 3 Sep User Guide
Samsung Digital Photo Frame SPF 71ES User Guide
Schumacher Battery Charger 520A PE User Guide