Specifications
Safety Information
WMA MP3 CD Player/Receiver
■
■
Read the operating instructions for the unit and all other compo-
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any prob-
lems resulting from failure to observe the instructions given in this
manual.
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the mean-
ings of the pictographs in order to use this manual and the system
properly.
General
FM Stereo Radio
Frequency range
Usable sensitivity
Frequency response
Alternate channel selectivity
Stereo separation
Image rejection ratio
IF rejection ratio
Signal to noise ratio
❑
❑
Do not install the product where it is exposed to strong
vibrations or is unstable.
Caution
Power supply
:DC 12 V (11 – 16 V), test voltage
:87.50 MHz – 108.00 MHz
:6 dB/µV (S/N 30 dB)
:30 Hz – 15 kHz ( 3 dB)
:75 dB
:35 dB (1 kHz)
:70 dB
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
CQ-C1301W
14.4 V, negative ground
:Less than 2.2 A (CD mode; 0.5 W 4
channels)
Observe the following cautions when using this
unit.
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
This unit is designed for use exclusively in automo-
biles.
Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Current consumption
Maximum power output
Tone adjustment range
BAND
CQ-C1301W
APM
:50 W x 4 (at 1 kHz), volume control
maximum
PWR
CLOCK
DISP
Installation Angle
❑
MUTE
SCROLL
RANDOM
SCAN
REPEAT
SQ
SRC
1
2
3
4
5
6
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
Operating Instructions
:Bass: 12 dB at 100 Hz, Treble: 12
dB at 10 kHz
:100 dB
:62 dB
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
❑
❑
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
Dimensions (W x H x D)
Weight
:4 – 8 Ω
AM Radio
Frequency range
Usable sensitivity
tions. Failure to heed the instructions may result in
severe injury or death.
:2.5 V (CD mode, 1 kHz, 0 dB)
:200 Ω
Warning
Caution
injury or material damage.
:531 kHz – 1 602 kHz
:28 dB/µV (S/N 20 dB)
❑
❑
❑
Wear gloves for safety. Make sure that wiring is com-
pleted before installation.
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
:178 x 50 x 160 mm
:1.3 kg
Disc Player
❑
❑
Observe the following warnings when installing.
❑
Sampling frequency
:8 times oversampling
:1 bit DAC System
:Astigma 3-beam
:Semiconductor laser
:790 nm
:20 Hz – 20 kHz ( 1 dB)
:96 dB
:0.01 % (1 kHz)
:Below measurable limits
:75 dB
Warning
DA converter
Disconnect the lead from the negative (–) battery termi-
nal before installation.
Wiring and installation with the negative (–) battery terminal con-
nected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fix-
ing the product or its accessories.
Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if pos-
sible.
Never install the product in a location where it interferes
with your field of vision.
Never have the power cord branched to supply other
equipment with power.
Pick-up type
Observe the following warnings when using this
unit.
The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driv-
er from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
Light source
Observe the following cautions when handling the
battery for the remote control unit.
●
●
Wave length
Note:
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
❑
¡ Specifications and design are subject to modification without
notice due to improvements.
¡ Some figures and illustrations in this manual may be different
from your product.
Use only specified battery (CR2025).
Match the polarity of the battery with the (+) and (–) marks in
the battery case.
Observe the following cautions when installing.
Refer wiring and installation to qualified service per-
sonnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
●
●
Replace dead battery as soon as possible.
Remove the battery from the remote control unit when not using
it for an extended period of time.
Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
Dispose of the battery according to the local regulations.
Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
❑
❑
❑
Use the proper power supply.
❑
Accessories
●
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other bat-
tery systems, especially a 24 V DC battery system.
Instruction kit
Mounting Collar
Installation kit (YEP0FZ5698)
●
●
(YEFX0217263)
Operating Instructions
Lock Cancel Plate
Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
(English : YEFM285618)
Q'ty: 1
Q'ty: 1
❑
❑
❑
❑
(êÛÒÒÍËÈ : YEFM285640)
Trim Plate
(YEFC051002)
Q'ty: 2
Q'ty: 1
Q'ty: 1
In case of battery leakage
(
(
: YEFM285641)
: YEFM285642)
Mounting Bolt
●
●
●
Thoroughly wipe the battery liquid off the battery case and insert
new battery.
If any part of your body or clothing comes into contact with bat-
tery liquid, wash it with plenty of water.
If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
❑
❑
(YEFM285643:
)
Take care not to damage the leads.
Power Connector
(YEAJ02877)
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
Q'ty: 1 set
Rubber Bushing
Do not disassemble or modify the unit.
Installation Instructions
(English, êÛÒÒÍËÈ,
Q'ty: 1
Do not disassemble, modify the unit or attempt to repair the prod-
uct yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Servicenter.
,
POWER
SOURCE MENU
SEL
SRC
Remote Control Unit
(includes a battery)
(EUR7641010)
YEFM293903)
VOL
SET
:
BAND
MUTE
1
2
3
REPEAT
6
R
A
N
D
O
M
S
C
A
N
4
5
7
TUNE
8
0
9
TUNE
(YEFM293904:
)
#
NUMBER
DISP
❑
❑
❑
CAR AUDIO
❑
❑
❑
Q'ty: 1 set
Do not use the unit when it is out of order.
❑
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to over-
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
Q'ty: 1
Note:
After installation and wiring, you should check the nor-
mal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufactur-
er before installation.
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment.
The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engi-
neer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
TEXT
❑
heat and will result in fire or other damage.
¡Please read these instructions carefully before using this product and keep this manual for future reference.
❑
❑
Make sure the leads do not interfere with driving or get-
ting in and out of the vehicle.
Panasonic welcomes you to our constantly growing family of electronic products owners.
Caution
Insulate all exposed wires to prevent short circuiting.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected compo-
nents, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring
you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a
member of our family.
THIS PRODUCT IS A CLASS 1 LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
Matsushita Electric Industrial Co., Ltd.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
YEFM285618A NT1204-1015
Printed in China
Preparation
Maintenance
Notes on Discs
Notes on MP3/WMA
Note: MP3/WMA encoding and writing software is not sup-
Folder selection order/file playback order
This unit is designed and manufactured to ensure the minimum of maintenance. Use a dry, soft cloth for routine exteri-
or cleaning. Never use benzine, thinner, or other solvents.
If you use commercial CDs, they must have the label
shown at right.
Some copy-protected music CDs are not playable.
plied with this unit.
Set your car's ignition switch to the ACC
Press [DISP] (Display).
The demonstration screen is canceled, and no more
appears.
1
2
Root Folder
1
(Root Directory)
or ON position.
TEXT
Points to remember when making MP3/WMA files
The demonstration screen appears.
2
q
How to hold a disc
¡ Do not touch the underside of a disc.
¡ Do not scratch on a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Common
Folder Selection
4
Printed side
C
ON
AC
Press [SRC] (PWR: Power).
¡ High bit rate and high sampling frequency are recom-
mended for high quality sounds.
e
r
1
8
In the order
–
3
3
w
File Selection
In the order
¡ Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
¡ The playback sound quality differs depending on the
encoding circumstances. For details, refer to the user
manual of your own encoding software and writing soft-
ware.
Note: If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR) for more than 4 seconds.
–
5
6
q
y
Do not use irregularly shaped discs.
If the replaced fuse fails, contact your nearest authorized Panasonic Service Center.
8
Do not leave discs in the following places:
¡ Direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ Seats and dashboards
t
y
7
Warning
Tree 1
Tree 2
Tree 3
Tree 4
Tree 8
(Max.)
Pull the insulation film out from
the backside of the remote con-
trol gently.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest
authorized Panasonic Service Center.
MP3
Maximum number of files/folders
¡ Maximum number of files: 999
¡ Maximum number of files in one folder: 255
¡ It is recommended to set the bit rate to “128 kbps or
Do not use irregularly shaped discs.
<Wrong>
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
more” and “fixed”.
¡ Maximum depth of trees: 8
WMA
<Correct>
Do not attach any seals or labels to your discs.
¡ Maximum number of folders: 255 (Root folder is includ-
¡ It is recommended to set the bit rate to “64 kbps or
more” and “fixed”.
ed.)
Do not write on the disc label with a ballpoint pen or
other hard-point pens.
¡ Do not set the copy protection on the WMA file to enable
this unit to play back.
Note:
Anti-Theft System
¡ This unit counts the number of folders irrespective of the
presence or absence of MP3/WMA file.
¡ If the selected folder does not contain any MP3/WMA
files, the nearest MP3/WMA files in the order of playback
will be played.
¡ Playback order may be different from other MP3/WMA
players even if the same disc is used.
¡ “ROOT” appears when displaying the root folder name.
The 24-hour system is used for the clock.
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Clock Display at Power Off
Press [DISP] to change the display.
Caution
¡ You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make
playback impossible.
¡ Some CD-R/RWs cannot be played back successfully due
to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is
not closed.
¡ You may encounter trouble in playing MP3/WMA files or
displaying the information of MP3/WMA files recorded with
certain writing software or CD recorders.
¡ The file extension “.mp3“ or “.wma” should be assigned to
each file depending on the file format.
¡ This unit does not have the play list function.
¡ Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
Press [DISP] (CLOCK).
1
Never assign the “.mp3”, or “.wma” file name
extension to a file that is not in the MP3/WMA
format. This may not only produce noise from
the speaker damage, but also damage your
hearing.
(clock display)
Caution
¡ Do not touch the contacts on the face plate and the main
Display off
¡ This face plate is not waterproof. Do not expose it to
Hold down [DISP] (CLOCK) for more than
2 seconds.
unit, since this may result in poor electrical contact.
water or excessive moisture.
2
¡ If dirt or other foreign substances get on the contacts,
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
wipe them off with a clean and dry cloth.
Hours blinks
areas where the temperature rises high.
Clock display
Display Information
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Romeo
Adjust the hour.
3
Displayed items
¡ CD-TEXT
Disc title
Track title
Hours set
¡ MP3 (ID3 tag)
Album name
Removing
Mounting
Note: Apple HFS, UDF 1.50, MIX mode CD, CD Extra is not
[[]: sets the hour ahead.
supported.
¡ This player cannot play the CD-R/RW discs which contain
other than CD-DA or MP3/WMA data (Video CD, etc.).
¡ Be sure to observe the instructions of the CD-R/RW disc
for handling it.
Turn off the power.
Slide the left side of the face plate in place.
Title name/Artist name
1
1
2
[]]: sets the hour back.
¡ MP3/WMA
Folder name
File name
¡ WMA (WMA tag)
Album name
Compression formats
(Recommendation: “Points to remember when making
MP3/WMA files” on the right.)
Press [ ]. The face plate will open.
Press the right end of face plate until a
“click” is heard.
2
3
Press [DISP] (CLOCK).
4
Windows Media, and the Windows logo
are trademarks, or registered trade-
marks of Microsoft Corporation in the
United States and/or other countries.
Pull it out toward you.
Title name/Artist name
Minutes blinks
Recording MP3/WMA files on a CD-media
¡ MPEG 1 audio layer 3
Bit rate: 32 k – 320 kbps
¡ Windows Media
Audio Ver. 2, 8
Bit rate: 64 k – 192 kbps
VBR: No
Sampling frequency:
32, 44.1, 48 kHz
¡ You are recommended to minimize the chances of mak-
ing a disc that contains both CD-DA files and MP3/WMA
files.
¡ If CD-DA files are on the same disc as MP3 or WMA files,
the songs may not play in the intended order, or some
songs may not play at all.
¡ When storing MP3 data and WMA data on the same disc,
use different folders for each data.
¡ Do not record files other than MP3/WMA files and unnec-
essary folder on a disc.
Displayable characters
Adjust the minute.
5
¡ Name files and folders in accordance with the standard of
each file system. Refer to the instructions of writing soft-
ware for details.
VBR: Yes
Minutes set
Sampling frequency:
32, 44.1, 48 kHz
¡ MPEG 2 audio layer 3
Copyright
[[]: sets the minute ahead.
¡ ASCII character set and special characters in each lan-
guage can be displayed.
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself per-
sonally.
[]]: sets the minute back.
Bit rate: 8 k – 160 kbps
2
1
Press [DISP] (CLOCK).
VBR: Yes
Note:
6
¡ With some software in which MP3/WMA format files
have been encoded, the character information may not be
displayed properly.
¡ Undisplayable characters and symbols will be converted
into an asterisk ( ).
Sampling frequency:
16, 22.05, 24 kHz
Complete
No warranty
¡ The name of MP3/WMA file should be added by rules as
shown in the following descriptions and also comply with
the rules of each file system.
1
Note:
Above description complies with our investigations as of
December 2004. It has no warranty for reproducibility and
displayability of MP3/WMA.
¡ “ADJUST” is displayed before adjusting the clock.
¡ Hold down []] or [[] to change numbers rapidly.
2
|