Model GXT300/325/400/450 Series
®
TABLE OF CONTENTS
2
Introduction
3
Important Notice, FCC Licensing
LCD Display
4
5
Controls
5
Battery Installation
6
Installing the Belt Clip
Charging the Optional Battery Pack
Low Battery Level Indicator
OperatingYour Radio
External Speaker/Microphone Jack
Troubleshooting Guide
Use and Care
Specifications and Frequency Charts
Warranty Information
MIDLAND Family Products
Accessories
6
7
7
8 - 13
14
15
15
16
17
18
18
19
Accessories Order Form
Model GXT300/325/400/450 Series
®
CHARGINGTHE OPTIONAL BATTERY PACK
Your GXT300/325/400/450 Series is equipped for using an optional
rechargeable NiMH battery pack (not included) which can be
recharged using a desktop charger (not included). Initial charge time
is 24 hours with a charge time of 8-12 hours thereafter. For maximum
battery life, we recommend charging the battery pack when the low
battery icon comes on. Remove the radios from the charger when the
charge time expires.
To charge using a Desktop Charger:
1. Place the rechargeable battery packs in the radios.
2. Connect the AC adapter into an AC wall outlet.
3. Insert the AC adapter plug (or DC Cigarette Lighter adapter if
charging in vehicle) into the desktop charger jack.
4. Place the units into the desktop charger slot and note that the LED
indicator with RED color will light up, indicating charging function.
When the battery pack reached a substantial voltage level, the LED
indicator will change to GREEN color .
However, this does not ensure that the battery pack is fully
charged so it is recommended that the battery pack be charged
for at least 12 hours.
1. Only use our NiMH battery pack.
2. Do not attempt to charge alkaline batteries or any batteries
or battery packs other than the one indicated in the manual.
This may cause leakage and damage to the radio.
3. For long term storage of the radio, turn the radio OFF and
remove the batteries from the radio.
!
LOW BATTERY LEVEL INDICATOR
Your GXT300/325/400/450 Series has a LOW BATTERY ICON
which will only appear on the LCD display if the battery voltage level
is low. At this point, the battery needs to be charged for at least
12hrs.
Model GXT300/325/400/450 Series
®
GXT300/325 SERIES QUICK REFERENCE CHART
Roger Beep
Silent Operation
On/Off
eVOX
Call Tone
1~3
MENU
Channel
Privacy
Power
oF/1/2
1~22
oF~38
H/L
On/Off
GXT400/450 SERIES QUICK REFERENCE CHART
Roger Beep
Silent Operation
On/Off
Call Tone
1~5
eVOX
Vibrate
MENU
Channel
Power
Privacy
Press &
hold Menu
button
oF/1/2
On/Off
On/Off
1~22
H/M/L
oF~38
WX Channel
1~10
MONITOR
Pressing and holding the MONITOR button for 1 second will let you
hear noise so you can adjust the volume level of the radio when not
receiving a signal. This should be used to check activity on your
current channel before transmitting.
Press and hold the MONITOR button for 1 second again to get out
of MONITOR mode.
SCAN
Your GXT300/325/400/450 Series can scan all 22 channels for
activity. To enter, quickly press the SCAN button. Repeat the same
procedure to exit. Your radio will rapidly scan each of the 22 channels
and stop on any active channel for 5 seconds before resuming scan.
When you press the PTT button to transmit on an active channel, the
scanning function will stop and remain on the active channel. To
resume scanning, quickly press the SCAN button.
Model GXT300/325/400/450 Series
®
SETTING PRIVACY CODES
Your GXT300/325/400/450 Series has 38 Privacy codes available.
The selected Privacy Code may be different for each channel. To
select a Privacy Code for the current channel press the MENU button
twice, and then the
buttons to select one of the 38 Privacy
/
Codes. To confirm the selection, press the PTT button or press MENU
button again to move to the next feature setting.
Note : Selecting a Privacy Code of "oF" will disable the Privacy
feature. To communicate between two GXT300/325/400/450
Series radios, all radios in your group must be set to the same
!
channel and Privacy Code selections.
TRANSMIT (TX) POWER LEVEL SELECTION :
Your GXT300/325 Series has 2 transmit power levels and the
GXT400/450 Series has 3 power level settings. To select the power
level on channels 1~7 and 15~22, press the MENU button three times,
a “Pr” icon will appear blinking on the display. Then press the
/
buttons to select TRANSMIT POWER LEVEL icon (H: Hi/
M: Mid/L: Lo). To confirm, press the PTT button or press MENU
button again to move to the next feature setting. When the PTT
button is pressed during Low Battery Level condition, the TX
Power will automatically switch from Hi(H) to Lo(L) level.
Note : You cannot adjust the power setting on the FRS
channels (8~14). They are set to Low power per FCC
regulations.
!
eVOX (Hands-freeTransmission)
Your GXT300/325/400/450 Series has 2 eVOX level settings:
(oF/1/2).
To set eVOX, press the MENU button four times. The display shows
“VOX” blinking while on the right of the CHANNEL NUMBER display,
an “oF” icon appears. Select “1” or “2” by pressing the
buttons
/
and push the PTT key, or press MENU button again to move to the
next feature setting.
eVOX will be more sensitive on the “2” setting than on the “1” setting.
To turn eVOX off, press the MENU button four times. The display
shows “VOX” blinking while on the right of the CHANNEL NUMBER
display, a “1” or “2” icon appears. Select “oF” by pressing the
/
buttons and push the PTT key, or press MENU button again to
move to the next feature setting.
|