FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits
SDI Technologies Inc.
1299 Main Street,
Rahway
NJ 07065
Tel. No.: (732) 574-9000
Getting Started
Thank you for purchasing the iHome iH64 Computer Speaker System for your iPod. Designed
specifically to work with your Computer and iPod, this system provides high quality audio
performance that brings out the best in your music.
Please read this instruction book carefully before operating the iH69 and keep it for future reference.
Check for iPod compatibility
iH64 is an advanced system and supports most updated iPod features. To make sure your iPod works properly with iH64,
please update your iPod firmware with the latest version via iTunes.
Quick Start: Connections
1:connections
2:power
3:inserts
Important: Turn off iH64 before
connecting or disconncting speakers!
1. Power off iH64.
2. Connect the right speaker to the
speaker jack on the back of main unit.
3. Connect the left speaker to the speaker
jack on the back of right speaker.
Attach the AC adaptor cable to
the jack on the back of the main
unit and plug the other end into a
working wall socket.
Select the dock insert for your
iPod model from the table below
and place insert in dock.
Never dock an iPod without an
insert in place.
Use this insert
For this iPod
3rd Gen nano
insert 13
iPod Touch
insert 14
thin iPod with video (30 GB)
Insert 9
iPod with video (60,80 GB)
Insert 10
thick (60, 80 GB) iPod with video
thick (160 GB) iPod classic
thin (30 GB) iPod with video
thin (80GB) iPod classic
3rd Gen nano
iPod Touch
to purchase the proper insert.
For portable operation,
Insert iPod into dock with
proper insert (iPod must
not be in a skin or case).
iPod will charge while
docked.
Press the Power button
on the iH64 then press
play/pause button on your
iPod to play the iPod.
4:iPod
5:batteries
remove the battery
compartment door on the
bottom of the main unit
and insert 4 AAA batteries
(match + and - polarity to
diagram in compartment).
Replace door. Will not
charge iPod when
operating on batteries.
1
Controls and Indicators
Top Panel
iPod sync Button
iPod sync LED
iPod sync
iPod Dock
Volume - Button
Volume + Button
Power LED
Power Button
Rear Panel
USB Port
Line-in Jack
Speaker Jack
iPod sync
AC Adaptor Jack
line-in
DC 7.5V 2A speaker
2
Using iH64
Install iPod Insert
Your iH64 comes with inserts to ensure your iPod fits properly in the dock.
To place an insert:
1. Select the insert for your iPod (see table on page 1).
2. Gently press the iPod insert into the dock.
3. Carefully place your iPod into the dock. The iPod must not be in a case or “skin”.
Connect Speakers
Important: You must turn off the iH64 before connecting or disconnecting speakers!
1. Power off iH64.
Install iPod Insert
2. Connect the right speaker to the speaker jack on the back of main unit.
3. Connect the left speaker to the speaker jack on the back of right speaker.
Install AC Adaptor
Connect the AC adaptor cable plug into the jack on the back of the main unit, then plug the AC adaptor into the wall outlet.
This AC adaptor is for use with the iH64 only. To avoid damage, do not use other
adaptor with the iH64.
Install/Replace Battery
1. Open the battery compartment cover located on the bottom of the unit.
2. Insert 4 “AAA” batteries, checking that the polarity (the + and – ends of the batteries)
matches the drawing inside the battery compartment. We recommend the use of alkaline
batteries for longer life.
3. Close the compartment cover.
Batteries information:
•
•
•
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
Make sure you dispose of batteries properly (see your local regulations).
Install batteries
Note: The iPod does NOT charge when the iH64 is operating on batteries.
Charging Your iPod
Note: Please make sure you are using the correct insert for your iPod (see Install iPod Insert) and that it is properly docked
into the iH64.
1. While your iPod is docked in the unit and the unit is connected to AC power, it recharges until fully charged. iPod will
not be overcharged. Note that other non-docking iPods will NOT charge. Your iPod will NOT charge when the unit
is running on battery power.
Listening to Your iPod
1. Dock the already playing iPod. The iH64 will automatically turn on and you will hear the music playing from your iPod.
Note: If the volume of the song/music playing is too low on the iPod itself, iH64 may not detect iPod is in play mode.
Press the Power Button on the main unit once to play your iPod.
2. When the iPod is docked and in standby mode, press the Button on the iH64 and then press Play/Pause on your
iPod to play it. The blue LED Power indicator will stay on to show the power is on.
3. Press Play/Pause on your iPod to pause play; press again to resume it.
4. Press the
and Button on the iH64 to adjust the system volume.
5. Press Button to turn iH64 and iPod off.
3
Listening to non-docking iPod or other audio devices
If you are using an iPod without a docking port or other MP3 player or portable audio device, you can play it through the iH64
via the Line-in Jack.
1. Plug one end of an audio cable (available at www.ihomeaudio.com) into the headphone or line-out jack on your device
and the other end of the audio cable into the iH64 Line-in Jack.
2. Press the Button to turn the iH64 on.
3. Press the or
Buttons to adjust the system volume. You may need to adjust your device volume, too.
4. Press the Button to turn the iH64 off. Please remember to turn off your device, too. Note: do not connect and play
an external audio device while a docked iPod is playing or you will hear both audio signals.
Syncing your iPod to a Computer through iH64
The iH64 allows you to sync your docked iPod with a computer directly from the iH64 without removing the iPod.
1. Plug the USB cable into a powered USB port on your computer and the other end to the iH64’s USB port located on the
back of the main unit.
2. Make sure the iPod is properly docked. Press the iPod Sync Button located on the top of iH64. A green LED under the
iPod Sync Button will light up to indicate computer sync mode is active. The unit will take a few seconds to start syncing
with iTunes. When an iPod is syncing, DO NOT undock your iPod or press the iPod Sync Button. During computer sync
mode, you cannot control your iPod through the iH64 remote.
3. Once syncing is completed, you must eject your iPod through iTunes before pressing the iPod Sync Button to
exit sync mode.
When an iPod is syncing, DO NOT undock your iPod OR press the Sync Button
Changing the Speaker Panels
The iH64 comes with 3 pairs of detachable speaker panels (one is already installed).
1. Pull out the speaker panel from speaker to remove the speaker panel.
2. To replace the speaker panel into the speaker, simply line up the panel and press firmly
into place. Make sure the panel is placed properly so it does not vibrate.
Operating the Remote On/Off Switch
To save battery power, switch the Remote On/Off Switch on the bottom of the main unit
to Remote Off. Doing so disables the remote control. The switch will not function while using
the AC adaptor.
remote
off
remote
on
Remote On/Off Switch
4
Using the Optional Remote Control
Power Button turns unit ON and OFF
Volume Buttons raise and lower volume on the unit.
Pressing FWD/REV while iPod is inserted will FWD/REV to next/previous track
docked will s
Pressing and holding FWD/REV while iPod is
within currently playing track.
can forward/reverse
Pressing Play/Pause from power off mode will play iPod.
Pressing Play/Pause while iPod is
Press again to resume play.
aying will pause iPod.
docked and pl
Pressing the up/down buttons for Bass and Treble, will raise or lower bass or treble
iR70
Pressing the SRS WOW button will toggle the SRS WOW sound enhancement effect on
and off.
Remote not included
with all iH64
models.
To order a remote,
please visit
Pressing the reset button will reset Bass and Treble level to 0 and turn SRS WOW
sound effect on.
Pressing the mute button will mute unit.While unit is muted, LED will flash as long
as unit is muted. Pressing mute again or pressing volume up or down will unmute.
The up, down, fwd, rev, menu, and enter buttons are used to navigate the iPod.
The shuffle and repeat buttons will activate/deactivate the iPod’s shuffle
and repeat modes.
Install/Replace the Remote Control Battery
The remote control battery is already installed at the factory. When the remote control stops operating or its range seems
reduced, it is time to replace the battery with a new one.
1. The battery compartment is located on the back end of the unit.
2. Slide the battery compartment door to release the battery door.
3. Remove the old battery and insert a new CR2032 battery, checking that the + and – sides
of the battery match the drawing on the battery door.
4. Replace the battery door on the remote control.
Note: Make sure you dispose of batteries properly (see your
local regulations).
Battery Compartment
5
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in
these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through
the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where
it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning
instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings
or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power
cable should be unplugged from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.
or call 1-800-288-2792 Toll Free
6
Trouble Shooting
Symptom
Possible Problem
Solution
Unit doesn’t
AC adaptor isn’t plugged to a wall
outlet or the connector is not
plugged into the power supply jack
on the back of the unit
Plug the AC adaptor into a wall outlet and plug the
connector into the supply jack on the unit
respond
(no power)
Wall outlet is not functioning
Plug another device into the same outlet to
confirm the outlet is working
iPod does not
dock properly
Using no or wrong iPod insert
Dock or connector is obstructed
Make sure the dock insert is the proper one for your iPod
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iPod does not
respond to the
unit
iPod is not docked properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
Your iPod software is too old
iPod is locked up
Upgrade software on your iPod via iTunes
Please refer to your iPod manual for details.Please make
sure your iPod is working properly before docking in
the unit.
iPod doesn’t
charge up
iPod is not docked properly
Using 3rd generation iPod
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iH64 doesn’t support 3rd generation iPod
iPod is locked up/frozen
Please refer to your iPod manual for details. Please make
sure your iPod is working properly before dock into the unit.
iPod battery has problem
Unit is operating on battery power
Connect to AC outlet with AC adaptor
Sound is distorted Volume level is set too high
Sound source is distorted
Decrease the volume. Turn off EQ/SRS WOW effect
If iPod original sound source is poor quality, distortion and
noise are easily noticed with high-power speakers.
Try a different audio source such as a music CD.
If you are using an iPod Shuffle or external sound source
like older generation iPod, try reducing the output volume
on the device itself. Also, try reducing bass.
Remote Control
doesn’t work
Remote Battery is weak/dead
Remote Control is too far way
Remote switch is in OFF position
Replace with new remote battery
Use the Remote Control closer to unit
Make sure Remote switch on bottom of unit is ON
7
Solucionando Problemas
Síntoma
Causa Posible
Solución
La unidad no
El adaptador de AC no ha sido
conectado a la corriente eléctrica
o el cable no ha sido conectado
a la parte posterior de la unidad.
Conecte el adaptador AC al tomacorrientes y el cable a la
ficha de entrada de la unidad.
responde
(no enciende)
El tomacorrientes no funciona.
Conecte otro aparato al mismo tomacorrientes para
verificar si se encuentra activo.
El iPod no
encastra
correctamente
El encastre no es el correcto o no
ha colocado encastre alguno.
Verifique tener el encastre correspondiente antes de
intentar acoplarlo al aparato.
La muesca o el encastre están
obstruidos.
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
El iPod no se
comunica con
la unidad
El iPod no está colocado
correctamente.
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
El software (programa) de su
iPod es obsoleto
Actualice su programa vía iTunes.
El iPod está trabado
Verifique el correcto funcionamiento de su iPod antes de
acoplarlo a la unidad. Por favor, refiérase al Manual del
Usuario de su iPod para mayor información.
El iPod no carga El iPod no está colocado
correctamente.
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
El iPod es de 3ra generación.
El iPod está trabado.
El iH64 no soporta iPods de 3ra generación.
Verifique el correcto funcionamiento de su iPod antes de
acoplarlo a la unidad. Por favor, refiérase al Manual del
Usuario de su iPod para mayor información.
La batería del iPod tiene algún
problema.
El sonido sale
distorsionado
El nivel de volumen está alto
Baje el nivel de volumen. Apague la función EQ/SRS WOW.
Si la grabación original de sonido del iPod o MP3 era de
mala calidad, escuchará ruido/distorsión al ser amplificada
mediante los parlantes de alta potencia. Intente utilizar
otra fuente de sonido como la música de un CD.
La fuente de sonido está
distorsionada
Si utiliza un iPod Shuffle o una fuente de sonido externa
como un iPod de generaciones anteriores, intente bajar el
volumen del aparato en sí. También puede intentar reducir
los bajos.
El control remoto Las pilas están descargadas.
no funciona
Coloque pilas nuevas.
El control remoto está fuera del rango Acerque el control remoto al parlante izquierdo.
del parlante izquierdo.
8
Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects
in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center
listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is
$30.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Drive
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
© 2008 SDI Technologies, Inc. All rights reserved
or call 1-800-288-2792 Toll Free
iH64-060508-A
Printed in China
|