Table of Contents
Quick Start
1
2
3
3
4
4
5
6
7
8
Controls and Indicators
Using iH17
Charging your iPod
Listening to your iPod
Listening to non-docking iPod or other audio devices
A Consumer Guide to Product Safety
Trouble Shooting
Solución De Problemas
Warranty Information
Maintenance
•
•
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material
should be placed between it and the furniture.
•
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine,
thinner or similar materials can damage the surface of the unit.
Quick Start
1:power
2:inserts
3:iPod
RESET
R E S E T
TESTT E S T
Insert iPod into dock with proper
insert (iPod must not be in a skin
or case). iPod will charge while
docked.
Press the power button on the
iH17 to play the iPod.
Select the dock insert for your
iPod model from the table below
and place insert in dock.
Never dock an iPod without an
insert in place.
Attach the AC adaptor cable to
the jack on the back of the iH17
and plug the other end into a
working wall socket.
iPod touch 2G
insert 16
nano 4G
insert 17
thin iPod with video (30 GB)
Insert 9
Use this insert
For this iPod
thin (30 GB) iPod with video
thin (80GB, 120GB)
iPod classic
iPod Touch 2G
nano 4G
NOTE: If you do not have an insert for your iPod, please visit
1
Controls and Indicators
Front Panel
Power Button
Press to power unit
ON or OFF
iPod Docking
Volume Down Button
Decrease volume
Volume Up Button
Power LED
Glows to indicate
unit is ON
Increase volume
Back Panel
Aux-in Jack
DC Jack
Connect aux audio source
Connect AC adptor
2
Using iH17
Install AC Adaptor
Connect the AC adaptor cable plug into the jack on the back of the iH17, then plug the AC
adaptor into the wall outlet.
Install iPod Insert
Your iH17 comes with inserts to ensure your iPod fits properly in the dock.
To place an insert:
1. Select the insert for your iPod (see table on page 1).
2. Gently press the iPod insert into the dock.
3. Carefully place your iPod into the dock. The iPod must not be in a case or “skin”.
Install iPod Insert
Installing/Replacing Batteries for Portable Operation
The iH17 uses 4 “AA” batteries for portable operation. The iH17 will not charge your iPod while operating on batteries.
If sound becomes weak or distorted, it is time to replace the batteries.
• Open the battery compartment cover located on the bottom of the unit.
• Insert 4 “AA” batteries as indicated.
• We recommend the use of alkaline batteries for longer life.
Batteries information:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium)
Install / Replace Batteries
batteries.
Charging Your iPod
Note: Please make sure you are using the correct insert for your iPod (see Install iPod Insert) and that your iPod is properly
docked into the iH17.
1. While your iPod is docked in the unit and the unit is connected to AC power, it recharges until fully charged. iPod will
not be overcharged. Unit will not charge iPod when operating on batteries.
3
Listening to Your iPod
1. Dock an already playing iPod and the iH17 will automatically turn on.You will hear the music playing from your iPod.
Note: If the volume on the playing audio is too low on the iPod, the iH17 may not detect that the iPod is in play mode.
Press the button once to play iPod.
2. When the iPod is docked and in standby mode, press the
3. Press play/pause on your iPod to pause play; press again to resume it.
4. Press the or buttons on the iH17 to adjust the system volume.
5. To turn off the unit, press the button on the iH17. Your iPod will continue charging while in the dock.
button on the iH17 to play your iPod.
Listening to non-docking iPod or other audio devices
1. Plug one end of an audio cable (available at www.ihomeaudio.com) into the headphone or line-out jack on your device
and the other end of the patch cord into the iH17 Aux-in Jack.
2. Press the button to turn the iH17 on.
3. Press the
4. To turn off the iH17, press the
or
Buttons on the iH17 to adjust the system volume. You may need to adjust your device volume, too.
button. Please remember to turn off your device, too.
NOTE: Do not connect and try to play an aux audio device while a docked iPod is playing or you will hear both.
4
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in
these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through
the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where
it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning
instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings
or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power
cable should be unplugged from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.
5
Trouble Shooting
Symptom
Possible Problem
Solution
Plug the AC adaptor into a wall outlet and plug the
connector into the supply jack on the unit
AC adaptor isn’t plugged to a wall
outlet or the connector is not
plugged into the power supply jack
on the back of the unit
Unit doesn’t
respond
(no power)
Wall outlet is not functioning
Plug another device into a wall outlet (same outlet) to confirm
the outlet is working
Batteries are weak/dead
Replace current batteries with fresh ones
Using no or wrong iPod insert
Dock or connector is obstructed
Make sure the dock insert is the proper fit to your iPod
iPod does not
dock properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iPod is not docked properly
iPod does not
respond to the
unit
Your iPod software is too old
iPod is locked up
Upgrade software on your iPod via iTunes
Please refer to your iPod manual for details.Please make
sure your iPod is working properly before docking in
the unit.
iPod touch and iPhone (touchscreen
units) will not respond if turned off
completely
Press and hold the wake/sleep button on top of your
iPhone/iPod touch to turn it on.
Unit will not charge iPod when running on batteries.
Connect unit to AC adaptor to charge iPod
Unit is operating on batteries/not
connected to AC adaptor
iPod doesn’t
charge up
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Then reseat it in the dock.
iPod is not docked properly
iPod is locked up/frozen
iPod battery has problem
Volume level is set too high
Please refer to your iPod manual for details. Please make
sure your iPod is working properly before dock into the unit.
Decrease the volume.
Sound is distorted
If iPod original sound source is poor quality, distortion and
noise are easily noticed with high-power speakers.
Try a different audio source such as a music CD.
Sound source is distorted
If you are using an iPod Shuffle or external sound source
like older generation iPod, try reducing the output volume
on the device itself. Also, try reducing bass.
Batteries are weak/dead
Replace current batteries with fresh ones
6
Solución De Problemas
Síntoma
La unidad no
responde
(no enciende)
Causa Posible
Solución
Conecte el adaptador AC al tomacorrientes y el cable a la
ficha de entrada de la unidad.
El adaptador de AC no ha sido
conectado a la corriente eléctrica
o el cable no ha sido conectado
a la parte posterior de la unidad.
Conecte otro aparato al mismo tomacorrientes para
verificar si se encuentra activo.
El tomacorrientes no funciona.
Las baterías están gastadas
Reemplace las baterías
El encastre no es el correcto o no
ha colocado encastre alguno.
La muesca o el encastre están
obstruidos.
Verifique tener el encastre correspondiente antes de
intentar acoplarlo al aparato.
El iPod no
encastra
correctamente
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
El iPod no está colocado
correctamente.
El iPod no se
comunica con
la unidad
El software (programa) de su
iPod es obsoleto
Actualice su programa vía iTunes.
Verifique el correcto funcionamiento de su iPod antes de
acoplarlo a la unidad. Por favor, refiérase al Manual del
Usuario de su iPod para mayor información.
El iPod está trabado
El iPod Touch y el iPhone (unidades
con pantalla “touch”)
Oprima el botón de Encendido en la parte superior de su
iPhone/iPod Touch para encender la unidad.
El iPod no está colocado
correctamente.
Retire el iPod de la muesca y elimine la obstrucción.
Vuelva a acoplar su iPod.
El iPod no carga
El iPod está trabado.
Verifique el correcto funcionamiento de su iPod antes de
acoplarlo a la unidad. Por favor, refiérase al Manual del
Usuario de su iPod para mayor información.
La batería del iPod tiene algún
problema.
El sonido sale
distorsionado
El nivel de volumen está alto
Baje el nivel de volumen. Apague la función EQ/3D.
Si la grabación original de sonido del iPod o MP3 era de
mala calidad, escuchará ruido/distorsión al ser amplificada
mediante los parlantes de alta potencia. Intente utilizar
otra fuente de sonido como la música de un CD.
La fuente de sonido está
distorsionada
Si utiliza un iPod Shuffle o una fuente de sonido externa como un iPod de
generaciones anteriores, intente bajar el volumen del aparato en sí.
También puede intentar reducir los bajos.
Las baterías están gastadas
Reemplace las baterías
7
Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects
in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center
listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is
$20.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($20.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Drive
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
© 2009 SDI Technologies, Inc. All rights reserved
or call 1-800-288-2792 Toll Free
8
iH17-022409-Eng-B
Imprimé en Chine
|