|
USB 10base-T Ethernet Adapter
HYNEU010001
USER GUIDE
Information in this document is subject to change without notice. All
rights reserved. All brand names are registered trademarks of their
respective companies.
small office/home office (SOHO) environments.
The Hypertec USB Ethernet plugs directly into the USB port located on
the back of most modern computers, and eliminates the need to open the
PC when adding an Ethernet connection.
About the Universal Serial Bus (USB)
Universal Serial Bus (USB) is a peripheral bus standard developed by
PC and telecom leaders such as Compaq, DEC, IBM, Intel, Microsoft,
NEC and Northern Telecom. PCs equipped with USB allow computer
peripherals once installed on a system to be automatically configured as
soon as they are physically attached without the need to reboot or run
setup. Thus, USB brings true "out of the box" plug-and-play to computer
peripherals. USB features fast I/O transfer rate of 12 Mbits/s and allows
up to 127 devices to run simultaneously on one computer.
Typically, there are several connectors on the back of a computer, each
of which accepts a specific kind of device connector and cable. As a
result, a maze of confusing cables can be found at the back of a
computer when a full range of peripherals are attached, USB eliminates
the need for variety of connectors and cables because a single, standard
type of connector and cable is used for every peripheral device,
connected in a "daisy chain' fashion.
running
•
•
•
•
•
•
•
Full Windows 98 support
Supports the energy-saving and suspend-and-resume functions
No external power supply is required
RJ-45 female connector for Ethernet 10Base-T connection
Dual LED status indicators for Link and Activity
Ideal for home PC users
Self diagnostics at initialisation
HyperNet USB 10baseT Ethernet Adapter
Remove the entire contents of the HyperNet USB Ethernet adapter
package and verify that the following items have been included and none
have been damaged during shipment:
·
·
·
HyperNet USB Ethernet Adapter
3.5" USB Ethernet Software driver diskette
Installation Guide
Connecting the USB Ethernet Adapter
The USB Ethernet adapter hardware installation is a simple two-step
process:
1. Connect the USB Type A plug into the USB port on the computer.
2. Attach a UTP or STP network cable (Category 3 or 5) to the RJ-45
connector located on the other side of the adapter.
The UTP or STP network cable also needs to be connected to a suitable
10base-T compatible HUB device.
Disconnecting the USB Ethernet Adapter
When you have finished working with the USB Ethernet adapter, you
can disconnect it from the computer by pulling the Type A plug from
your computer.
Note: Upon reconnecting the USB Ethernet adapter to the computer,
allow approximately up to one minute for the system to recognise the
reconnected adapter.
Figure 1.
3.
Choose Search for the best drivers for your device (see figure 2)
and click Next.
Figure 2.
Figure 3.
6. Click Next to confirm driver selection (see figure 4)
Figure 4.
Figure 5.
8. Click finish to complete network installation, remove the driver
disk and click Yes to restart the computer (see figure 6)
Figure 6.
If at any time during installation you experience difficulties, please
contact Hypertec Technical Support on +44 1488 686844
(01488 686844 in the UK).
Data Transfer Rate:
10 Mbits/sec
Ethernet Connector:
Unshielded RJ-45 female connector
Ethernet LED's:
Green - Activity
Yellow - Link
Weight:
1.85 oz, 51gr. (Including the USB cable)
Physical Dimensions:
Length - 2.28" (58 mm)
Width - 1.69" (43 mm)
Thickness - 0.98" (25 mm)
Operating Voltage:
5 V (powered via the USB connection)
Power Consumption:
80mA (Active)
120mA (max)
Operating Temperature:
0°-70°C
Operating Humidity:
0% - 90% non-condensing
Certifications:
FCC Part 15, Subpart B class B
become the property of Hypertec.
This warranty applies only to the original registered end user purchaser
of the product and does not include service to repair damage resulting
from accident, disaster, misuse, abuse or non-Hypertec modification of
the product.
Additional components installed by the dealer or end user are not
covered by this warranty. Apart from the above, no warranty is
expressed or implied, including warranty of merchantability or warranty
of fitness for use for a particular purpose.
The liability of Hypertec is limited to the repair or replacement of the
product with a functionally equivalent or better product. Hypertec is not
liable for any accidental, general, special, exemplary or consequential
damages resulting from any product failure, even if Hypertec has been
advised of the possibility of such damages.
Hypertec Limited
Units 1-3 Station Road
Hungerford, Berkshire RG17 0DY
Ph: +44 (0)1488 686844
Fax:
Web:
Email:
+44 (0)1488 686845
|