HSK140HD
®
319-349
1.25 MILLION CANDLE POWER
CORDLESS RECHARGEABLE SPOTLIGHT
ROTATING HANDLE AREA UTILITY LIGHT
OWNER’S MANUAL
& WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USING, READ AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS,
PLUS YOUR VEHICLE’S BATTERY MANUFACTURER GUIDELINES. FAILURE TO DO SO COULD
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312
TOLL FREE: 800-916-7004
• Recharges from North American Standard household outlet.
• Separate ON/OFF switches for spotlight and area light.
• Comfortable folding, locking, 90° pistol grip.
• Flat area stand provides stability on tabletops and other flat surfaces.
NOTE: This unit is shipped in a partially charged state. Initially charge unit using the AC
charger for 15 hours. Charge after each use.
FIGURE 1
FIGURE 2
RUBBER BEZEL
FOLDED HANDLE
RECHARGE PORT
AREA LIGHT
HANDLE
RELEASE
BUTTON
HOUSING
SCREWS
WORK STAND
AREA LIGHT
SPOTLIGHT SWITCH
2. OPERATION
Two switches (Spotlight and Area Light) control On/Off operation of both lights. The SpotLight
can be continuously lit for up to 25 minutes on a full battery charge. The Area Light can be lit for
up to 15 hours on a full battery charge. Figure 1 shows locations of the handle, handle release
button and flat area stand. Figure 2 rear view, shows Spotlight/Off/Area light switch and
area light.
The handle rotates ninety degrees and locks in two different positions. The handle is released
from either locked position by pressing on the Handle Lock Button (located near two handle
screws) and rotating the handle to the new position. When the handle is close to the body of
the light (folded) the spotlight is carried with the weight of the unit below the handle. When the
handle is rotated to be perpendicular to the body of the unit, the unit is carried pistol style with
the unit’s weight on top. It is your choice of operating positions, depending on your needs
and comfort.
FIGURE 3
RECHARGING
PORT
FIGURE 4
90° SWIVEL
HANDLE
AREA
LIGHT
HANDLE AFTER
ROTATING 90°
FIGURE 5
3. RECHARGING
DC RECHARGING
ADAPTER
AC and DC Recharge requires use of either
of these supplied recharge adapters.
Do not charge spotlight using any other adapters.
(see figure 5)
DURING AC RECHARGE/OR DC RECHARGE:
a) Never turn on while charging.
b) After recharge – disconnect cord and wait 5 minutes before use.
AC RECHARGING
ADAPTER
3
Charging with 12 VOLT DC Adapter - Plug the DC fused Recharge Adapter (included)
into the Recharge Port (barrel receptacle) just behind the rubber Bezel and then insert the ciga-
rette lighter plug into the cigarette lighter socket of your vehicle or other 12 VDC power source.
Make sure the Locking Trigger Switch is in the OFF position. Allow approximately 3 hours
charging time if the engine is running.
WARNING: Use the supplied DC Recharge Adapter, do not substitute.
1. Move the rubber plug from the Recharge Port. It is there to keep out dust and moisture.
2. Connect the DC Recharge Adapter’s large cigarette lighter type plug to a 12 volt DC source.
3. Plug the adapter’s barrel connecter into the Recharge Port located near the rubber bezel.
4. Recharge for 3 hours maximum.
5. After recharge, disconnect the barrel connector from the Recharge Port and store the adapter.
6. Replace the rubber plug in the Recharge Port.
AC RECHARGE
Make sure that the AC source is 110/120 volts, 60 Hz.
WARNING: Use the supplied AC Recharge adapter, do not substitute with any other.
1. Lift the rubber plug from the Recharge Port. (see figure 3) It is there to keep out dust
and moisture.
2. Connect the AC adapter into wall outlet. (see figure 3)
3. Plug the adapter’s barrel connecter into the Recharge Port.
4. Recharge for 10 hours maximum.
5. After recharge, disconnect the barrel connector from the Recharge Port and store the adapter.
6. Replace the rubber plug in the Recharge Port.
4. PERIODIC MAINTENANCE
All batteries lose charge over time, especially when they are warm. AC recharge is recom-
mended every two months, when not in frequent use. Use the AC recharger and charge for the
recommended time. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with
a soft cloth moistened with a mild solution of water and detergent.
5. PARTS REPLACEMENT
Three parts are replaceable by users. The quartz halogen bulb and sealed lead acid battery are
proprietary and are available through HUSKY. A substitute 6 volt H3 55 watt bulb may be used
instead of a HUSKY bulb. These can also be purchased from popular automotive parts suppliers
nationwide. The DC charging adapter fuse is replaceable. Contact HUSKY’s Technical Support De-
partment for replacement parts and any additional information that you may need. They may be
reached toll free (800) 916-7004.
DC PLUG FUSE REPLACEMENT
The fuse in the DC plug protects the charging circuit of the DC Recharge Adapter. This fuse may
blow if the spotlight is operated when the DC Recharge Adapter is powered and the DC cord is
connected to the recharge port. During DC recharge, if there is no slight warming of the DC
plug, you should suspect that 6 volts DC is not powering the plug or the fuse is opened.
To replace the fuse:
1. Unscrew the end cap of the DC Plug. (counterclockwise)
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate replacement fuse with same type and rating.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight-DO NOT OVER-TIGHTEN
7. Check for proper operation of DC Charger Adapter.
SPOTLIGHT BULB REPLACEMENT
To replace the H3 type 6 volt bulb, you will need a small Phillips type screwdriver and a replace-
4
ment bulb. Bulb life can be shortened by installing a bulb with dirt or fingerprints on it. The bulb
can be wiped clean with cloth moistened with alcohol. During bulb installation, avoid touching
the glass part of the bulb. (See Figure 6A and 6B for details)
1. Disconnect the unit from any charging adapters and lock the trigger switch OFF
2. Lift up the Recharge Port plug from the Recharge Port
3. Pull off the rubber bezel to reveal two small Phillips screws.
4. Using the screwdriver, remove (counter clockwise) the two screws. Set them aside.
5. Lift off the retaining ring, glass, and rubber ring and set them aside.
6. Carefully remove the reflector and bulb assembly.
7. Disconnect the bulb wire from the red power wire and set the burned out bulb aside.
8. Unsnap the hairpin retaining wires from the reflector’s flange.
9. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector
(no need to completely remove this screw).
10. Lift out the bulb and the attached wire.
11. Insert the replacement bulb into the reflector’s flange.
12. Put back and secure the hairpin retaining wires.
13. Connect the bulb power wire to the red power wire.
14. Tighten the retaining screw on the flange.
15. Place the reflector in position in the body of the spotlight.
16. Replace the rubber “O” ring in the groove around the perimeter of the reflector.
17. Replace glass and retaining ring so that the screw holes are aligned.
18. Secure retaining ring with two screws.
19. Replace rubber bezel so that Recharge Port Plug can plug into the Recharge Port
20. Operate switch to ensure proper operation of spotlight.
REPLACING THE BATTERY PACK
The sealed lead acid battery has a life of several years, if recharged promptly after each use.
When a fully charged battery only provides about ten minutes or less of spotlight operation, it
should be replaced with a new one. To replace the battery, you will need a narrow shaft Phillips
type screwdriver and a replacement battery. The battery pack can be replaced by doing the
following:
1. Complete the bulb replacement steps through step 7 (above) to remove the reflector
assembly.
2. Remove the Phillips screws (clockwise) that fasten the two halves of the housing body.
(see figure 1 for locations.)
3. Separate the two body halves.
WARNING: DO NOT ALLOW BARE WIRES OR CONNECTORS TO CONTACT EACH OTHER;
DANGEROUS SPARKING CAN OCCUR
4. Note polarity of battery. Note which color wire is on which terminal.
5. Disconnect the wires from the battery and set the battery aside.
6. Connect the replacement battery, making sure the correct color wires are on the new
battery terminals. Make sure POS (+) is red and NEG (-) is black.
CAUTION: Incorrectly connected wires will allow the spotlight to operate normally but when
recharge adapters are connected, there will be damage to the battery and recharge
adapters. Double check battery polarity before reassembly!
HAIRPIN RETAINING
FIGURE 6A
WIRES
REFLECTOR
FIGURE 6B
BULB
LENS
™
I
N
G
,
L
t
d
.
M
A
N
U
F
A
C
T
U
R
T
w
e
r
S
P
O
R
T
P
O
S
A
0
0
R
0
,
0
P
o
U
L
T
a
n
d
l
e
C
2
,
0
0
RUBBER
BEZEL
PHILLIPS
HEAD
SCREW
O RING
RUBBER
PHILLIPS HEAD SCREWS
RETAINING RING
RECHARGE
PORT PLUG
REFLECTOR
5
7. Replace handle and recharge port assemblies in one half of the housing body.
Make sure wires and connectors do not touch.
8. Place other half of housing body into position and replace three Phillips screws
(clockwise). Do not overtighten.
9. Follow steps 14 through 20 for bulb replacement to reassemble reflector, rubber “O” ring,
glass, retaining ring and rubber bezel. Charge the new battery using AC Recharge Adapter
for a minimum of 12 hours initially, then seven hours thereafter.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed
of properly. Recycling is required, contact your local authority for information. Failure to
comply with local, state and federal regulations can result in fines, or imprisonment.
Battery Disposal Warnings:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
• For more information on recycling this battery,
call toll-free (877) 288-7722.
RECYCLE NON-
SPILLABLE LEAD
ACID BATTERY
6. SPECIFICATIONS
Spotlight Bulb.......................................................................................... 6 volt, H3 series
Battery ......................................... Maintenance free, sealed lead acid, 6 volt, 6 Amp Hour
Weight ............................................................................................... 3 lbs 2 oz (1.5 kg)
Length................................................................................................... 8.5 in (21.6 cm)
Width .................................................................................................... 6.0 in (15.3 cm)
Height (folded) ..................................................................................... 6.5 in. (16.5 cm)
6
WARRANTY:
HUSKY 2 YEAR LIMITED WARRANTY PROGRAM
The Home Depot warrants this Husky Power Product to the original user to be free from defects in material
and workmanship for a period of two years from the date of purchase. If you believe that this unit is
defective during its original two-year warranty period, return the unit, with proper proof of purchase to The
Home Depot store or send the product to Husky Power Products at the address below.
This Husky Power Products is warranted, to the original purchaser only, to be free of defects in materials
and workmanship for two years from the date of purchase without additional charge. The warranty does
not extend to subsequent purchasers or users. Husky Power Products will not be responsible for any amount
of damage in excess of the retail purchase price of the product under any circumstances. Incidental and
consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial or rental application, only a 90 day warranty will apply in this
instance. This warranty does not apply to accessories or damage to units from misuse or incorrect
installation. Misuse includes wiring or connecting to improper polarity power sources.
RETURN/REPAIR POLICY: If you believe that the product is defective during the it’s two year Limited
Warranty period, return the unit, with proof of purchase to the Home Depot Store. Defective products, may
also be returned postage prepaid to Husky Power Products. Any defective product, other than accessories,
that is returned to Husky Power Products within 30 days of the date of purchase will be replaced free of
charge. If such a product is returned more than 30 days but less than two years from the purchase date,
Husky Power Products will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at Husky Power Products’
option. A unit may be replaced with a new or reconditioned unit of the same or comparable design. The
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period.
The customer is responsible for the shipping charges on all returned items. During the warranty period,
Husky Power Products will be responsible for the return shipping charges to the customer.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or
exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized
use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood,
and Acts of God.
If your problem is not covered by this warranty, call Husky Power Products Technical Support Department
at toll-free (800) 916-7004 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific
legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Husky Power Products Technical
Support by telephone, fax or mail. We suggest that you keep the original packaging in case you need to
ship the unit. When returning a product, include your name, address, phone number, dated sales receipt
(or copy), and a description of the reason for return and product serial number. After replacing the unit, we
will return it to you within four weeks.
All HUSKY products must be registered within (30) days of purchase to activate this warranty.
Mail the completed registration form, along with a copy of the original sales receipt to:
®
ATTN.: CUSTOMER SERVICE / HUSKY
4140 SW 28th Way, Ft. Lauderdale, FL 33312
TOLL FREE: (800) 916-7004
WARRANTY MUST BE WITHIN 30 DAYS OF PRODUCT PURCHASE DATE.
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
7
®
© 2002 HUSKY PROFESSIONAL TOOLS
4140 SW 28 WAY
FT. LAUDERDALE, FL 33312
MADE IN CHINA
8
|