Instructions for Installation and Use
60cm Gas Cooker
GW74
C367G
To the Installer:
Before installation, fill in the product details on the back cover of this books.
The information can be found on the rating plate.
To the Use:
You must read the instructions prior to installing and using the appliance and
then retain them for future reference.
Introduction
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET
CAREFULLY.
Your new cooker is guaranteed and will give lasting service.
The guarantee is only applicable if the cooker has been installed in accordance
with the Installation Instructions.
The cooker is designed specifically for domestic use and responsibility will not
be accepted for use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a
window or use an extractor fan) and that persons who may be sensitive to the
odour avoid any fumes. It is suggested that any pets be removed from the room
until the smell has ceased. This odour is due to any temporary finish and also
any moisture absorbed by the insulation.
Our policy is one of continual improvement in design and development,
therefore strict accuracy of illustrations and descriptions cannot be
guaranteed.
This appliance conforms to the following EEC Directive:
Gas Appliances
90/396/EEC
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
3
For your Safety
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS make sure you understand the controls before using the cooker.
ALWAYS check that all controls on the cooker are turned off after use.
ALWAYS stand back when opening an oven door to allow heat to disperse.
ALWAYS use dry, good quality oven gloves when removing items from the ovens.
ALWAYS take care when removing items from the top oven/grill when the main
oven is on, as the contents may be hot.
ALWAYS keep the oven and grill doors closed when the cooker is not in use.
ALWAYS place pans centrally over the hotplate burners and position them so
that the handles cannot accidentally be caught or knocked or become
heated by other burners.
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can
cause a fire.
ALWAYS allow the cooker to cool before cleaning.
ALWAYS follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ALWAYS keep ventilation slots clear of obstructions.
ALWAYS turn off the electricity supply before cleaning or replacing an oven
lamp.
ALWAYS refer servicing to CORGI registered appliance service engineers.
4
For your Safety
NEVER . . .
NEVER leave children unsupervised where the cooker is installed as all
surfaces will get hot during and after use.
NEVER allow anyone to sit or stand on any part of the cooker.
NEVER store items that children may attempt to reach above the cooker.
NEVER heat up unopened food containers as pressure can build up causing the
container to burst.
NEVER store chemicals, food stuffs, pressurised containers in or on the
cooker, or in cabinets immediately above or next to the cooker.
1
3
NEVER fill a deep fat frying pan more than / full of oil, and never use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
NEVER place flammable or plastic items on or near the hotplate.
NEVER use proprietary spillage collectors on the hotplate.
NEVER use the cooker as a room heater.
NEVER dry clothes or place other times over or near to the hotplate or
oven/gril doors.
NEVER wear garments with long flowing sleeves whilst cooking.
NOTE: The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Always ensure that the kitchen is
well ventilated; keep natural ventilation holes open or install a mechanical
ventilation device (mechanical extractor hood).
In particular when using the grill or more than one hotplate burner, open a
window if a mechanical ventilation device is not operating.
5
Oven Timer Operation
The oven timer offers you the following features:
1. Time of Day
2. Automatic Cooking
3. Minute Minder
AUTOMATIC COOKING
The main oven can be controlled automatically.
GUIDANCE ON AUTOMATIC COOKING
1. Select foods which will take the same time to cook.
2. Set the oven timer so that the food has just finished or is just about to finish
cooking on your return to the oven. This will ensure the food has not cooled down
and does not require reheating before serving.
3. Food should be as cold as possible when it goes into the oven, ideally straight
from the refrigerator. Frozen meat and poultry should be thawed thoroughly
before it is put in the oven.
4. Warm food should never be placed in the oven if there is to be a delay period. Stews
prepared by frying the meat and vegetables should be cooked as soon as possible.
5. Dishes containing left-over cooked poultry or meat, for example Shepherds Pie,
should not be cooked automatically if there is to be a delay period.
6. Stews and joints should be cooked by the long slow method, so that the delay
period is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,
joints, etc) the delayed start should be kept to a minimum.
8. Wine or beer may ferment and cream may curdle during the delay period, so it is
best to add these ingredients just before serving.
9. Foods which discolour should be protected by coating in fat or tossing in water to
which lemon juice has been added, prior to placing food in the oven.
10. Dishes containing liquid should not be filled too full to prevent boiling over.
11. Food should be well sealed (but not airtight) in a container to prevent the loss of
liquid during cooking. Aluminium foil gives a good seal.
12. Ensure food is cooked thoroughly before serving.
6
Oven Timer Operation
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will
remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible tone and
the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:–
–
–
When the timer is in manual mode, or
During the actual Cook Period.
‘AUTO’ will light up:–
–
When the timer is first turned on it will flash. It will go out when a time of day
is set or when the timer is set to manual.
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indi-
cate that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,
turn the oven controls off, ensure that the correct time of day is set, and press
the “Manual” button – The ‘AUTO’ symbol will go out).
TIMER FUNCTION BUTTONS
Minute Minder
Button
Here you can set a time period of up to 23 hours 59 minutes, that will count down.
When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button Cook Period is the actual length of time for which, the timer will switch the oven(s)
on as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
End Time Button
The time of day at which you want an “Auto Cooking” programme to end.
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear
a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.
Notes:
-
When setting an Auto Cooking programme you will need to set the oven
control(s) to the required temperature(s) when you set the timer.
If an Auto Cooking programme has been set the oven(s) will only operate during
the pre-programmed time.
-
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to
Manual operation.
“+” and “–” Buttons Used to adjust the various timer function settings.
7
Oven Timer Operation
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press & hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”
or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day.
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been
set.
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will
disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be checked at any
time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by
pressing and holding the Minute Minder button and then at the same time
pressing the “–” button until 0.00 appears in the display window.
8
Oven Timer Operation
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches
off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the ‘cookpot’ symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook Period
using the “+” and “–” buttons.
Release the buttons and the timer display will revert to the time of day with the
‘Auto’ symbol and ‘cookpot’ symbol lit.
Step 5 Press and hold in the End Time button.
The display will read the earliest possible end time for the Cook Period
that you have set above.
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.
Step 6 With the End Time button still held in, use the “+” and “–” buttons to set
the ‘End Time’ (i.e. The time you require the oven to switch off).
Release all the buttons and the timer will revert back to the time of day.
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme has
been set. The ‘cookpot’ symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if necessary
select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an
intermittent bleeping sound will be heard.
The audible tone will continue unless cancelled.
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual
operation (see below).
Step 8 Press the Manual button, the audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
9
Oven Timer Operation
Note 1 When cooking automatically the Cook Period can be checked at any time by simply
pressing the Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by simply
pressing the End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK
PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven
function.
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the
‘cookpot’ symbol will light up.
With the Cook Period button still held in set the required Cook Period using the
“+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
The timer display will revert to the time of day with the ‘Auto’ symbol lit &
‘cookpot‘ symbol remaining lit.
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent
audible tone will be heard.
NOTE: The Cookpot symbol disappears
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to
flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual button. The audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
10
Oven Timer Operation
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press the Manual button to return the oven(s) to “Manual” operation.
The ‘Auto’ symbol will go out.
Note 1
When cooking automatically the Cook Period can be checked at any time by simply pressing
the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook
Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time
button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device within the
timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity supply to
the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated
and completely cooked.
6. To set each function always press and hold the required function button and at the same time press “+” or
“–” buttons.
11
Hotplate
The hotplate lid is fitted with a safety device which cuts off the gas supply to
the hotplate burners unless the lid is fully open. Do not use the safety device as
a means of controlling the hotplate burners.
The hotplate has two high speed burners and two simmering burners which will
1
accommodate pans between 100mm (4”) and 240mm (9 /2”) diameter. All pans
should be positioned centrally over the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the lid and then raise it
to its fully open position.
2. Press the ignition button and then push in and turn the control knob
of the chosen burner anti-clockwise to the large flame symbol.
Continue to press the ignition button until the sparks light the gas.
3. Turn the control knob anti-clockwise to reduce the heat input.
Only turn the control knob between the large flame symbol and the
small flame symbol when adjusting the setting.
4. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid
lighting of the burners every time they are used, the ignitors must be kept clean
and dry. Remove any food spillage or cleaning materials from the ignitor using a
small nylon brush such as a tooth brush. Access to the ignitor can be achieved by
lifting off the loose burner parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful
not to drop any food particles or cleaning materials into the burner bases, to
avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top
edge of the pan support fingers. See ‘Care and Cleaning’ section for cleaning
information.
12
Hotplate
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the
hot oil or fat. Frozen foods in particular will cause frothing and
spitting if added too quickly.
5. Always keep the outside of the pan clean and free from streaks of oil
or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish
the fire.
Do not use water or a fire extinguisher as the force of it may spread
the burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
13
Grill
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
The grill is fitted with a safety device that will cut off the gas supply to the
burner if the flame is extinguished for any reason. Each time the grill is used,
the safety device has to be activated by pushing and holding in the control knob
for 3 seconds after the gas has lit.
A gentle flow of air will be blown from underneath the control panel when the
grill or top oven is in use. If the fan fails to blow air when the grill is in use, you
should contact your service engineer immediately.
GRILL PAN AND HANDLE
The grill pan handle is detachable from the pan to facilitate cleaning and
storage. The handle can be fixed as follows :
1. Remove the screw and washer from the grill pan bracket.
2. Tilt the handle over the recess. (A)
3. Slide the handle towards the centre of the pan. (B)
4. Locate the handle over the bracket. (C)
For a fixed handle, replace the screw and washer and ensure they are fully
tightened.
If a detachable handle is required, do not replace the screw and washer.
Warning : Ensure when using the grill pan handle in the detachable manner it is
centralised and secure.
The grill pan can be stored in the top compartment with the handle attached by
placing the shelf in the middle or lower position and tilting the grill pan over the
rear edge of the shelf.
A
B
C
14
Grill
TO USE THE GRILL
1. Open the top oven/grill door and remove the grill pan.
2. Remove the heat shield from the rear of the shelf for maximum grilling area.
3. Place the shelf in the appropriate position.
4. Press the ignition button and then push in and turn the control knob
clockwise to the large flame symbol. Continue to push in the control knob
for a further 3 seconds after the gas has lit, to allow time for the safety
device to operate.
If the burner extinguishes when the control knob is released, repeat the
procedure ensuring the control knob is fully depressed and allowing more
time for the safety device to operate.
5. Slide the grill pan along the shelf towards the rear of the grill compartment
until it stops.
6. Turn the control knob anti-clockwise to reduce the heat input. Only turn the
control knob between the large flame symbol and the small flame symbol
when adjusting the setting.
7. To turn off, turn the control knob anti-clockwise to the symbol O.
The grill cannot be used at the same time as the top oven.
If for any reason the grill burner has not lit after 15 seconds, turn the control
knob to the off position, leave the grill goor open and wait for at least one
minute before attempting to light the burner again.
An odour may be noticed when first using the grill – this should cease after a
short period of use.
DO NOT use the grill with the door closed.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat,
intensify the heat and create a fire hazard.
RELIGHTING THE BURNER
In the event of the burner flames being accidentally extinguished, turn off the
burner control and do not attempt to re-ignite the burner for at least one
minute.
Grilling can be started from cold but for best results preheat for approximately
two minutes. Most cooking is done with the heat on full, but it may be desirable
to reduce it for thicker pieces of meat or for keeping food warm.
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked
Alaska, place the dish on the floor of the grill compartment. The base of the grill
pan can be used for warming fruit garnishes on the reduced setting.
REMOVE HEAT SHIELD
FROM SHELF WHEN
GRILLING FOR MAXIMUM
GRILLING AREA.
NOTE: Strong detergents used in dishwashers may damage the grill pan grid
finish; clean in soapy water as described in CARE AND CLEANING section.
Always ensure that the grill pan handle is correctly fitted to the grill pan.
If necessary tighten any loose screws with a screwdriver.
15
Main Oven
The main oven is fitted with a safety device that re-lights the burner if the
flame has been extinguished for any reason and another safety device that
reduces the gas flow to a safe level if, for any reason, the burner fails to light.
The oven has different heat zones – the thermostat settings refer to the
temperature on the middle shelf position; above this shelf it is hotter and below
it is cooler. Two shelves provide six possible cooking levels enabling full use of
the different temperatures inside the oven.
Each shelf has a safety stop to prevent if from being pulled out too far when
attending to food. Shelves are removed from the oven by pulling them out to
the stop and then lifting them at the front to withdraw.
The maximum size of baking tray that should be used is 325mm x 350mm (13” x 14”).
TO USE THE MAIN OVEN
1.
Check that the timer is set to manual.
2.
Place the oven shelves in the appropriate positions (refer to cooking
charts).
3. Push in and turn the oven control knob fully anti-clockwise. Sparking will
continue until the burner is lit.
4.
Turn the control knob clockwise to the required setting (refer to cooking
chart).
There is a delay of about one minute whilst the safety device operates
before the burner comes on full.
5. To turn off, turn the control knob fully clockwise the the symbol O.
Never place dishes over the burner.
An odour may be noticed when first using the oven – this should cease after a
short period of use.
16
Main Oven
COLD START COOKING
Anything requiring long slow cooking such as casseroles and rich fruit cakes can
be put into a cold oven. Satisfactory results can also be obtained with creamed
mixture, rich pastries or yeast mixtures, but for perfection we recommend pre-
heating the oven for about 15 minutes at the gas mark you require for cooking.
ROASTING OF LARGE POULTRY
The maximum weight of poultry that can be accommodated is 11.5kg (25 lbs) of
suitable shape.
It is important to check that the bird DOES NOT overhang the burner at the
back of the oven.
STORAGE AND RE-HEATING OF FOOD
It is vitally important to strictly adhere to the basic principles of food handling
and hygiene to prevent the possibility of bacterial growth.
1. If food is to be frozen or not served immediately, cool it in a clean container
as quickly as possible.
2. Completely thaw frozen food in the refrigerator before re-heating.
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven,
Mk. 6, and then serve immediately.
4. Only re-heat food once.
‘COOK CHILL’ DISHES
These should always be placed in a pre-heated oven ideally on the first or
second shelf position. Follow the packet instructions for cooking time.
ALUMINIUM FOIL
If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.
17
Main Oven Cooking Chart
The following times and setting are for guidance only. You may wish to alter the
setting to give a result more to your satisfaction. When a different setting to
that shown below is given in a recipe, the recipe instructions should be followed.
Allow 15 minutes preheat for best results.
Always turn the thermostat knob to Mark 9 first, before turning back to the
required Gas Mark.
Shelf position 1 is the highest.
Gas
Mark
Shelf
Food
Positions Approx. Cooking Time and Comments
STARTERS
Patés and Terrines
FISH
1
2
3 or 4
4
1 / - 2 hrs
25 mins - 1 hr, depending on recipe
and size of fish
Oily Fish (whole)
4 or 5
4 or 5
3
3
White Fish (fillets & steaks)
25 - 30 mins.
MEAT AND POULTRY
Veal
5
4
25 mins per lb (450g) + 25 mins
Beef
4 or 5
4
25 - 30 mins per lb (450g) + 25 mins
40 mins per lb (450g) covered in foil
+ 40 mins per lb (450g) uncovered
Ham
5
4
Lamb
5
4
30 - 35 mins per lb (450g) + 30 mins
40 mins per lb (450g) + 40 mins
25 mins per lb (450g) + 25 mins
25 mins per lb (450g) + 25 mins
15 - 20 mins per lb (450g) + 20 mins
Pork
5
4
Chicken
Duckling & gosling
Turkey
5
4
4
5
4 or 5
6
4 or 5
4
50 mins. Remove bacon for last 15 mins.
Add extra 15 mins if roasting brace
Game birds
Casseroles
1
2
3
3 or 4
1 / - 6 hrs. (depending on type of meat)
PUDDINGS
1
1
4
2
2 / - 2 / hrs stand dish on a baking tray and
started with warm milk
Milk Puddings
3
3
4
3
3 or 4
Baked Custard
Baked sponges
Baked Apples
3 or 4
45 mins in bain-marie
3
4
40 - 50 mins
30 - 45 mins depending on the size
and type of apples
Meringue
puddings
14
or
55
1
mins
or
until
Apple Pie 1x9" (230mm)
Fruit crumbles
6
3
3
45 - 55 mins stand dish on a baking tray
35 - 45 mins
5 or 6
18
Main Oven Cooking Chart
Gas
Mark
Shelf
Positions
Food
Approx. Cooking Time and Comments
CAKES, PASTRIES AND BISCUITS
Small cakes - 2 trays
5
5
4
5
2
4
2
6
5
7
2 & 4
2 or 3 only
2 & 4
2
17 - 25 mins
"
- 1 tray
Victoria sandwich 2x8" (205mm)
25 - 35 mins
Fatless sponge 2x7" (180mm) -
3 egg mix
20 - 25 mins. 2 tins side by side
1
2
Christmas cake
3 or 4
3
4 - 6 / hrs depending on recipe
1
1
4
2
Madeira cake 7" (180mm)
Rich Fruit cake 9" (230mm)
Shortcrust pastry
Rich Shortcrust pastry - 1 tray
Flaky & puff pastry - 2 trays
- 1 tray
1 / - 1 / hrs
1
2
3
3 - 3 / hrs.
2 or 3
2
15 mins - 1 hr depending on recipe
20 - 40 mins depending on recipe
10 - 30 mins depending on recipe
1 & 3
2 or 3
2
"
"
"
"
Choux pastry - éclairs 1 tray
Scones - 2 trays
6
7
35 - 40 mins
10 - 15 mins
"
2 & 4
2 or 3
4
- 1 tray
Shortbread - 7" (180mm) round
Biscuits - 2 trays
2
4
55 - 1hr depending on thickness
15 - 20 mins depending on recipe
1 and 3
2 or 3
- 1 tray
"
"
"
"
YEAST MIXTURES
Bread
7 or 8
7 or 8
5
3 or 4
2 or 3
2 or 3
45 - 50 mins
15 - 20 mins
30 - 40 mins
Rolls
Chelsea buns
MISCELLANEOUS
Yorkshire Pudding - large
7
7
1 or 2
1 or 2
3
45 - 50 mins
25 - 30 mins
30 mins
- individual
Soufflés
4
2 - 5 hrs starting on shelf 4 until 'set'
and then on the baseplate until dried
out - turn when necessary.
Meringues
Slow Cook
4 &
baseplate
1
2
Baked Potatoes
4 or 5
3
1 / - 3 hrs until soft, depending on size
When baking with two trays or tins on two levels, the top tray is removed first and the lower
tray moved up to the top position for a few minutes longer.
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and
not those indicated on the cooking chart.
19
The Slow Cook Setting
The ‘Slow Cook’ setting on the main oven thermostat is used for slow cooking,
keeping food warm and warming plates for short periods.
USING THE ‘SLOW COOK’ SETTING FOR SLOW COOKING
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum 6
hours. They will ‘hold’ at this setting for a further hour but marked deterioration
in appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at Mk. 6 for 30 minutes before
turning to the ‘Slow Cook’ setting and never be cooked lower than the middle
shelf position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not be
cooked using the ‘Slow Cook’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air
circulation.
5. A meat thermometer should be used when cooking pork joints and poultry.
The internal temperature of the food should reach at least 88˚C.
6. This method is unsuitable for stuffed meat and stuffed poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the
oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be
cooked lower in the oven whilst other dishes requiring greater heat can be
cooked above them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day
cooking sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten m inutes after
soaking, before inclusion in any dish.
20
Top Oven
The top oven can be used to cook small quantities of food or used in conjunction
with the main oven to provide additional cooking space.
The top oven is fitted with a safety device that will cut off the gas supply to the
burner if the flame is extinguished for any reason. Each time the top oven is
used, the safety device has to be activated by pushing and holding in the control
knob for 3 seconds after the gas has lit.
A gentle flow of air will be blown from underneath the control panel when the
grill or top oven is in use.
The shelf in the top oven has a heat shield fitted at the rear.
The shield can be removed for cleaning and grilling, but should
be replaced when using the oven for best cooking results. It has
a safety stop to prevent it from being pulled out too far when
attending to food. The shelf is removed from the oven by
pulling it out to the stop and then lifting at the front to withdraw.
The maximum size of baking tray that should be used is 300mm x 350mm (12” x 14”).
TO USE THE TOP OVEN
1. Remove the grill pan and check that the heat shield is fitted to the shelf.
2. Place the top oven shelf in the appropriate position (refer to cooking chart).
3. Press in the ignition button and then push in and turn the control knob fully
anti-clockwise. Continue to push in the control knob for a further 3 seconds
after the gas has lit to allow time for the safety device to operate.
If the burner extinguishes when the control knob is released, repeat the
procedure ensuring the control knob is fully depressed and allowing more
time for the safety device to operate.
4. Turn the control knob clockwise to the required setting. (refer to cooking chart).
5. To turn off, turn the control knob clockwise to the symbol O.
Always push the door firmly closed to ensure that there is no loss of heat
through the door seal.
If for any reason, the oven burner has not lit after 15 seconds, turn the control
knob to the OFF position. Leave the top oven door open and wait for at least
one minute before attempting to light the burner again.
GUIDANCE ON USING THE TOP OVEN
1. Best results are obtained by pre-heating the oven for about 15 minutes.
2. Food which is higher than or will rise above 125mm (5”) cannot be cooked in
the top oven.
Never place dishes over the burner.
An odour may be noticed when first using the oven – this should cease after a
short period of use.
RELIGHTING THE BURNER
In the event of the burner flames being accidentally extinguished, turn off the
burner control and do not attempt to re-ignite the burner for at least one
minute
21
Top Oven Cooking Chart
The following times and setting are for guidance only. You may wish to alter the
setting to give a result more to your satisfaction. When a different setting to
that shown below is given in a recipe, the recipe instructions should be followed.
Allow 15 minutes preheat for best results. Always turn the thermostat knob to
Mark 8 first, before turning back to the required Gas Mark.
Gas
Shelf
Food
Mark
Position
Approx. Cooking Time and Comments
20-30 mins.
FISH
Oily and white fish
MEAT AND POULTRY
Beef (medium)
Ham (covered in foil)
Lamb
5
middle
4 or 5
lower
lower
lower
lower
lower
lower
lower
lower
25-30 mins per lb + 25-30 mins
40 mins per lb + 40 mins
5
5
5
5
5
4
3
30-35 mins per lb + 30 mins
40 mins per lb + 40 mins
Pork
Chicken
25 mins per lb + 25 mins
Duckling & Goose
Turkey
25 mins per lb + 25 mins
15-20 mins per lb + 15-20 mins
2-4 hrs. depending on meat used.
Casseroles
VEGETABLES
Baked jacket potatoes
PUDDINGS
1
2
5
middle
1 / - 2 hrs.
1
2
Milk Puddings (500ml/1pt)
Baked Custard (500ml/1pt)
Baked Sponge Puddings
Baked Apples
3
middle
middle
middle
middle
1 / - 2 hrs.
3
45 mins - 1 hr. in bain-marie of cold water.
30 - 45 mins
4
3
45 mins - 1 hr. depending on size
Meringue
Topped
Puddings
1middle
60 mins
45 - 50 mins
25
mins
until
ting
Apple Tart (1 x 205mm/8”)
Fruit Crumble
6
5
middle
middle
If using aluminium foil:
1. Remember it is important to increase the cooking time by one third.
2. Do not allow the foil to touch the sides of the oven.
3. Do not cover the oven interior with foil.
4. Do not cover the oven shelves with foil.
22
Top Oven Cooking Chart
Gas
Mark
Shelf
Positions
Food
Approx. Cooking Time and Comments
CAKES, PASTRIES AND BiSCUITS
Small Cakes (16 per tray)
Victoria sandwich (2 x 180mm / 7”)
Swiss Roll (3 egg quantity)
Christmas cake (1 x 205mm / 8”)
Madeira cake (1 x 180mm / 7”)
Rich Fruit cake (1 x 180mm / 7”)
Gingerbread
5
4
middle
middle
middle
middle
middle
middle
middle
middle
middle
middle
middle
middle
middle
middle
20 - 25 mins.
25 - 30 mins.
6
10 - 12 mins.
2
4 - 5 hrs depending on recipe
1 hr.
4
2
21/4 - 21/2 hrs.
3
11/2 - 13/4 hrs.
Scones - 16 per tray
Shortbread (1 x 180mm / 7”)
Biscuits
7
12 - 15 mins.
2
45 mins. – 1 hr. depending on thickness
15 - 25 mins.
4-6
6
Shortcrust Pastry
Rich Short Crust
15 mins. – 1 hr. depending on recipe
20 - 30 mins.
5
Flaky/Puff Pastry
7
10 - 30 mins. depending on recipe
25 - 35 mins.
Choux Pastry
6
YEAST MIXTURES
Bread - rolls, plait
7
middle or lower 25 - 35 mins
Tea breads etc.
5
middle
25 - 30 mins
MISCELLANEOUS
Yorkshire Pudding - small
- large
7
7
middle
middle
20 - 25 mins
30 - 40 mins
4
Meringues
1lower /2 21
-
hrs.
turn
when
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and
not those indicated on the cooking chart.
23
Care and Cleaning
Switch off the electricity supply and allow to cool before cleaning the cooker.
Clean the cooker regularly and wipe up spills soon after they occur to prevent
them from becoming burnt on. Never use biological washing powder, caustic
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or
oven chemical cleaners of any kind.
If it is necessary to remove the cooker for cleaning, ensure that it is cool and
beware that it is heavy (approximately 70 kg 155 lbs). To move the cooker
forward, open the top oven/grill door and with both hands positioned under the
roof of the compartment, lift and pull forward. Replace by pushing the cooker
backwards. Check that the cooker is level. Take care not to damage any floor
coverings.
OVEN HEAT CLEAN LININGS
The oven side linings are coated with a special enamel which has a
continuous cleaning action. The higher the oven temperature the more effective
the action. In most cases this cleaning operation will proceed during normal
cooking. However, if roasting is done frequently, or high temperatures are not
used regularly, it may be necessary to occasionally operate the oven empty at
Mark 8 for about an hour.
It should not normally be necessary to clean the linings with water, but if
desired, wipe them over with a soapy cloth, followed by a wipe with a damp clean
cloth.
OVEN DOORS (GW74 only)
The door inner glass panels can be removed for ease of cleaning by simply
sliding the panels out of the frame.
REPLACEMENT OF OVEN LIGHT BULB
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK.
Light bulbs are not covered by the manufacturer’s guarantee.
A new 25W, 300˚C rated SES bulb can be obtained from your cooker supplier or
any major electrical retailer.
1.
Remove the shelves from the oven.
2.
Unscrew the lens using a thick cloth to protect your fingers in the unlikely
event of a lens fracture.
3. Unscrew bulb.
4.
Fit new bulb and refit lens.
24
Care and Cleaning
COOKER FINISH
CLEANING METHOD
Vitreous Enamel
Control panel (C367), door
inner panels (C367),
hotplate, pan supports,
burner caps, roasting dish,
grill pan, main oven base,
inside of grill compartment
Cloth wrung out in warm soapy water. Stubborn
stains can be removed with a cream paste,
liquid cleaner or by rubbing with fine steel wool
soap pads.
Check that the cleaning agent is approved by
the Vitreous Enamel Association.
Wash with a cloth wrung out in warm soapy
water only.
DO NOT USE ABRASIVES.
Paint
Control panel trim (GW74),
side panels, doors trims.
Similar to paint cleaning above. Use a nylon
brush to remove any cleaning materials, water
or dirt from the hotplate burner bodies.
Aluminium
Hotplate burner bodies, lid
rear trim.
Glass
As for enamel cleaning. Polish with a clean dry
cloth or kitchen roll.
Wipe with a cloth wrung out in warm soapy
water.
A fine steel wool soap pad e.g. Brillo, Ajax, or a
chrome or stainless steel cleaner may be used.
Chromium Plating
Oven shelves, grill pan grid,
grill pan handle support
Plastic
Grill pan handle, control
knobs
Wipe with a cloth wrung out in warm soapy
water.
Wipe with a cloth wrung out in warm soapy
water. Polish with a clean dry cloth or kitchen
towel. For stubborn stains, use a proprietary
stainless steel cleaner and follow the
instructions on the container.
Stainless Steel
25
Something Wrong with your Cooker
Before contacting your Service Centre or Installer, check the problem guide
below, there may be nothing wrong with your cooker.
PROBLEM
CHECK
If all burners fail to ignite:
Check that sparks appear at the burners; a
clicking noise should be heard.
If not;
Burner will not light:
Check that the electricity supply is turned on.
If the electricity supply has failed, the hotplate,
grill and top oven burners can be lit by a match.
Grill burner
If only one burner fails to ignite:
Check that the burner is dry and that spillage of
food or cleaning fluid remains are not affecting
the ignitor or burner ports.
Burner ports
Ignitor
Clean away any debris with a dry nylon brush such
as an old toothbrush. If a wire wool pad has been
used for cleaning around the burner ensure the
ignitor is free from any stray strands. Any water
on the burner should be dried with a cloth or
kitchen towel.
Hotplate burner
On the hotplate make sure that all the burner
parts are correctly seated.
Burner ports
Ignitor
26
Something Wrong with your Cooker
PROBLEM
CHECK
Slight odour or small
amount of smoke when
grill / oven used first
time.
This is normal and should cease after a short period.
Check that the gas mark and shelf positions are as
recommended in the Oven Cooking Charts. However, it
may be necessary to increase or decrease the
recommended setting slightly to suit your taste.
Oven cooks too fast or
too slow.
Cannot set an “Auto Cook” Read the Timer instructions in this book carefully
programme or cannot get remembering that the Cook period is the length of time
the timer to turn the oven that the timer will switch the oven(s) on as part of an
on or off at the required
times.
Auto Cooking Programme.
The electricity supply to the cooker may have been been
interrupted, but has now come back on again. set the
correct time of day by following the instructions given in
the timer section of this book.
Timer Display shows "0:00"
with "Auto" Flashing.
Main oven does not work,
but the grill, top oven and
hotplate burners work.
The timer may be set for an Auto Cooking Programme.
Check the timer to see if “AUTO” is illuminated. If it is,
follow the instructions given in the timer section of this
book to cancel the Auto Cooking Programme.
The oven lamp is not covered by the guarantee.
Oven lamp does not
work.
The part is easily changed (see the section on oven lamp
replacement). A new lamp may be obtained from our
Spare Parts department, see Key Contacts (back page).
Disposal of your product
To minimise the risk of injury to children please dispose of your product carefully and
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off
flush with the appliance and always ensure that no plug is left in a condition where it
could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the disposal
of your product.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances must be collected separately in
order to optimise the recovery and recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
27
Installation
Prior to installation, ensure that the local distribution conditions (nature of the
gas and gas pressure) and the adjustment conditions are compatible. The
adjustment conditions for this appliance are stated on the data badge which is
fitted on the back panel.
This appliance is not designed to be connected to a combustion products
evacuation device. It must be installed and connected in accordance with
current installation regulations. particular attention should be given to the
relevant requirements regarding ventilation.
MODEL NUMBERS GW74, C367G
Category II2H3+ (GB)
These models are set to burn NATURAL GAS (G20) at 20 mbar but can be
converted for use on BUTANE (G30) at 28-30mbar or PROPANE (G31) at 37mbar
with the use of the LPG conversion kit that can be obtained free of charge, if
you contact our Genuine Parts and Accessories department (see Key Contacts,
back page).
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in
accordance with the current edition of the above regulations. It is in your
interest and that of safety to ensure compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice.
The cooker must also be installed in accordance with BS 6172.
Failure to install the cooker correctly could invalidate the warranty liability
claims and could lead to prosecution.
LOCATION
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but
not in a room containing a bath or shower. The cooker must not be installed in a
bed-sitting room of less than 20m3.
When adjusted for use on Butane (G30) or Propane (G31), the cooker must not
be installed in a room or internal space below ground level, e.g. in a basement.
PROVISION FOR VENTILATION
The room containing the cooker should have an air supply in accordance with
BS 5440: Part 2.
The room must have an opening window or equivalent; some rooms may also
require a permanent vent. If the room has a volume between 5 and 10m3, it will
require an air vent of 50cm2 effective area unless it has a door which opens
directly to outside. If the room has a volume of less than 5m3, it will require an
air vent of 100cm2 effective area. If there are other fuel burning appliances in
the same room, BS 5440: Part 2 should be consulted to determine air vent
requirements.
28
Installation
TECHNICAL DATA
1
1
2
2
Gas connection
Rp / ( / " BSP female)
Pressure test point
Gas rate adjustment
Aeration adjustment
Front left hotplate injector
None
None
Electrical connection
Flexible cord fitted with a 3 pin 13 amp plug
230/240V a.c. 50Hz. 13A fuse.
G30 at 28-30mbar
G20 at 20mbar
G31 at 37mbar
HEAT
INPUT
HEAT
INPUT
INJECTOR
116
INJECTOR
BURNER
HOTPLATE
Front left and rear right
3.0 kW
2.0 kW
3.0 kW (220g/h) 86
2.0 kW (145g/h) 70
HOTPLATE
Front right and rear left
103
GRILL
3.7 kW
2.5 kW
1.9 kW
150
115
100
3.4 kW (245g/h) 92
2.3 kW (165g/h) 72
MAIN OVEN
TOP OVEN
1.9 kW (135g/h)
65
29
Installation
SPACE FOR FIXING
The cooker can be close fitted below hotplate level. This requires a minimum
distance of 600mm between cupboard units of hotplate height.
When installing next to a tall cupboard, partition or wall, for a minimum distance
of 400mm above hotplate level, allow a side clearance of at least 65mm.
The diagram below illustrates the minimum clearance between the cooker and
adjacent walls, cupboards etc.
The wall behind the cooker, 50mm below and 450mm above, and the width of the
cooker, must be a non-combustible material such as ceramic wall tiles.
If the cooker is to be fitted close to a corner on the left hand side, ensure that
there is a clearance of at least 50mm to allow the main oven door to open fully
for when removing oven shelves.
65 mm Min
600 mm Min
COOKER HOODS
If a cooker hood is to be installed, refer to the cooker hood manufacturers’
instructions regarding fixing height.
30
Installation
UNPACKING THE COOKER
Unpack the components from inside the grill and oven: Check that the following
parts are present.
Grill pan and grid
Pan supports
Enamelled burner caps (4)
Aluminium burner bodies(4)
Top oven/grill shelf heat shield
Main oven shelves (2)
Top oven/grill shelf (1)
Literature
LEVELLING
Four skid feet are fitted which can be adjusted up or down to level the cooker.
CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31)
Each burner requires the injector to be replaced and bypass screws adjusted or
replaced as follows:
1.
Remove the loose hotplate burner parts.
2.
Using a 7mm socket, replace the hotplate injectors as appropriate (see table
on previous page).
3.
4.
5.
Re-position the loose burner parts.
Remove the enamelled baffle at the front of the grill (2 screws).
Remove the screw on the right hand side of the burner and gently slide the
burner off the injector.
6.
Using a 7mm socket, replace the grill injector as appropriate (see table on
previous page).
7.
Re-assemble the burner and baffle.
8.
Inside the top oven, remove the central screw securing the burner retainer.
Slide the retainer to the right slightly and lift away.
Lift the burner assembly and place on the floor of the oven to the right of the
burner opening.
9.
10. Using a 7mm socket, replace the oven injector as appropriate (see table on
previous page).
11. Re-assemble the oven burner and retainer.
12. Replace the main oven injector following the same procedure as for the top
oven.
13. From behind the cooker, remove the screws securing the rear panel and swing
the left hand side outwards (viewed from the rear) to gain access to the main
oven flame supervision device.
14. Replace the flame supervision device bypass screw.
15. Re-assemble the rear panel.
16. Carefully pull off the control knobs and timer buttons.
17. Remove the 2 screws securing the underside of the control panel. Slide the
control panel to the left slightly to remove.
continued...
31
Installation
18. Remove the 6 screws securing the timer mounting panel. Without completely
removing it, manoeuvre the timer mounting panel to gain access to the
thermostat bypass screws.
19. Using a narrow flat bladed screwdriver rotate the bypass screws fully
clockwise. The main oven thermostat bypass screw is located on the body of
the thermostat below the spindle, the top oven thermostat bypass screw is
located on the body of the thermostat to the right of the spindle and the
hotplate tap bypass screws are located down the centre of the spindle.
20. Re-assemble the control panel parts.
21. Secure the self-adhesive LPG conversion label over the gas details on the data
badge.
STABILITY CHAIN
A hole in the gas inlet valve bracket can be used to engage a stability chain.
CONNECTING TO GAS SUPPLY
Connection to the cooker should be made with an approved appliance flexible
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of
hose chosen should be such that when the cooker is in situ, the hose does not
touch the floor.
Those cookers converted to use on LPG should be connected with a hose
suitable for LPG and capable of withstanding a pressure of 50 mbar.
An adaptor backplate should be fitted within the shaded area shown, to allow
the cooker to be pushed fully to the wall and to ensure that the flexible hose is
only likely to come into contact with areas at the rear of the cooker that do not
exceed a temperature rise of 70˚C.
32
Electrical Connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
CONNECT TO A 230-240V A.C. SUPPLY ONLY.
Connection to the electricity supply should be made via a properly earthed, readily
accessible wall socket which is adjacent to but not directly above, and not more than
1.25m away from the appliance and capable of electrical isolation.
The mains lead should be routed such that it cannot touch hot parts of the cooker i.e.
the back panel above a height of 650mm from the floor.
Should this plug not fit the socket outlet in your home it should be cut off and replaced
with a suitable plug as outlined below.
NOTE: The removed plug cannot be used for any other appliance and should therefore be
properly disposed of and not left where children might find it and plug it into a supply
socket – with the obvious consequent danger.
IF THE FITTED PLUG IS REMOVED
The flexible mains lead must be correctly connected as below to a three pin plug of not
less than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a fuse
which is approved to B.S. 1362.
Green &
Yellow to
IMPORTANT: The wires in the mains lead fitted to this
Earth
appliance are coloured in accordance with the
following code:
Brown to
Live
Blue to
Neutral
GREEN AND YELLOW
BLUE
BROWN
– EARTH
– NEUTRAL
– LIVE
3 Amp
Fuse
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:– The
wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E or by the earth symbol
or coloured green or
green and yellow. The wire which is coloured blue must be connected to the terminal
which is marked with the N or coloured black. The wire which is coloured brown must be
connected to the terminal which is marked with the letter L or coloured red. When wiring
the plug, ensure that all strands of wire are securely retained in each terminal. Do not
forget to tighten the mains lead clamp on the plug. As the appliance must be earthed, do
not use 2-pin sockets outlets, if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be
carried out by a qualified electrician and should only be replaced with a flexible cord of
the same size i.e. 1.0mm2 cross sectional area PVC cable, available from our parts
department (see Back Cover).
IF A MOULDED PLUG IS FITTED
In the event of replacing a fuse in the plug supplied an ASTA approved fuse to BS1362
must be fitted.
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the
fuse cover the plug must not be used until a replacement fuse cover has been obtained
and fitted. A new fuse cover can be obtained from your local Electricity Board. The
colour of the correct replacement fuse cover is that of the coloured marks or inserts in
the base of the plug.
Make sure that the cable does not become trapped when pushing the cooker into position.
33
Installation
INSTALLATION AND OPERATIONAL CHECKS
After installation, check for gas soundness. The supply pressure can be checked
at the front left hotplate burner injector.
Fit the hotplate burner bodies and caps, pan supports and shelf shield(s).
Referring to the instructions for use where necessary,
1. Check that the hotplate burners ignite and cross-light to all ports. Check
for a steady flame on the low setting.
2. Check that the grill burner ignites and cross-lights to all ports and that the
flames remain when the control is released 3 seconds later, Check for a
steady flame on the low setting.
3. Check that with the main oven set to mark 9, the burner ignites at low rate,
and then increases to full rate within 60 seconds. Leave the oven full on with
the door closed for 10 minutes, and check that when the control is turned
to the ‘Slow Cook’ setting that the flame reduces.
4. Check that with the top oven set to mark 8, the burner ignites and that the
flames remain when the control is released 3 seconds later. Leave the oven
full on with the door closed for 10 minutes, and check that when the control
is turned to mark 1 that the flame reduces.
5. Check the operation of the oven timer and oven light(s).
Instruct the user on operation of the cooker.
On those models adjusted for use with LPG, it is normal for the oven and grill
burners to burn with yellow tips.
34
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, ensure that you can have
complete confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 0818 313 413
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK: 08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 0123 002 333
Genuine Parts and Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: 0818 313 413
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
06/2006 Part no. 195056871.01
|