SUBMERSIBLE TRAILER LIGHT KIT
Model 94137
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS.
©
Copyright 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
instruction sheet or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
PRODUCT SPECIFICATIONS
Item
Description
12 Volt DC / Negative Ground
Submersible Design
2 Combination, Class A, Stop-Tail-Turn Lights
License Plate Bracket
Power Source
Design Type
Features
25 Ft., Split Y-Style Harness
4 Ft., Color Coded Trunk Harness
18 LED’s Per Light (not serviceable)
Yes
Light Type
DOT Approved
Weight
3 Pounds
SAVE THIS INSTRUCTION SHEET
You will need this instruction sheet for the safety warnings and precautions, assembly instructions, parts
list, and assembly diagram. Keep your invoice with this instruction sheet. Write the invoice number on the
front of this instruction sheet. Keep this instruction sheet and invoice in a safe and dry place for future
reference.
UNPACKING
When unpacking, check to make sure all the parts shown on the Assembly Diagram are included. If any
parts are missing or broken, please call Harbor FreightTools at the number above as soon as possible.
SAFETY WARNINGS AND PRECAUTIONS
1.
2.
Use eye protection. Make sure to wear ANSI approved safety impact eye goggles when installing this
Light Kit.
Prior to installing this product, make sure to read and understand all instructions and safety precau-
tions as outlined in the(trailer, camper, etc.) manufacturer’s manual onto which the Light Kit will be
installed.
Trailer Light Mounting And Connection:
1.
Mount the Stop-Tail-Turn Light (1), marked “L.H.” (with the License Window), on the left rear of the
trailer with its side marker to the outside of the trailer. Then, mount the License Plate Bracket (2) with the
Stop-Tail-Turn Light. (See Illustration on previous page)
2.
3.
Mount the Stop-Tail-Turn Light (1), marked “R.H.” (without the License Window), on the right rear of
the trailer with its side marker to the outside of the trailer. (See Assy. Diagram)
Use the Metal Frame Clips included in the Mounting Hardware Package (5) to mount each half of the
Split Y-Style Harness (3) down each side of the trailer. Run the YELLOW and BROWN wires down the
left side and GREEN and BROWN wires down the right side of the trailer. (See Assy. Diagram)
4.
5.
Connect the YELLOW and BROWN wires to the left hand Stop-Tail-turn Light (1) with the Wire Nut
Connectors included in the Mounting Hardware Package (5). (See Assy. Diagram)
Connect the GREEN and BROWN wires to the right hand Stop-Tail-turn Light (1) with the Wire Nut
Connectors included in the Mounting Hardware Package (5). (See Assy. Diagram)
6.
7.
Attach the WHITE GROUND wire to the trailer tongue or frame. (See Assy. Diagram)
Connect the Split Y-Style Harness (3) Plug to the Color Coded Trunk Harness (4) Plug.
(See Assy. Diagram)
8.
9.
Turn on the towing vehicle’s headlights. The two Stop-Turn-Tail Lights (1) should turn on. The brighter
Stop Lights should turn on only when the vehicle’s brake pedal is depressed, or when the vehicle’s turn
signal is activated (ignition key must be in its “on” position).
If the Light Kit fails to illuminate, check all ground connections. If the turn signals on the Light Kit do not
illuminate, check the connections between the towing vehicle’s wiring and the Color Coded Trunk Har-
ness (4). (See Assy. Diagram.)
1
1
3, 4
2
5: MOUNTING HARDWARE
NOT SHOWN.
(Due to continuing improvements, actual product may differ slightly from the product described herein.)
Part #
1
2
3
Description
Qty.
Part #
4
5
Description
Color Coded Trunk Harness
Mounting Hardware (1 package)
Qty.
1
1
Stop-Tail-Turn Light
License Plate Bracket
Split Y-Style Harness
2
1
1
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF
ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT
OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 94137
For technical questions, please call 1-800-444-3353
PAGE 3
|