staple gun
3-way tacker kit
Model 96755
set up and Operating instructiOns
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe tHis Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
general saFety rules
warning! read all instructions
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
1.
2.
keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
keep bystanders, children, and visitors away while using this product.
Distractions can cause you to lose control. Protect others in the work area from
debris such as staples. Provide barriers or shields as needed. Keep children
out of the work area.
3.
stay alert. watch what you are doing, and use common sense when
operating the staple gun. do not use this product while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating this product may result in serious personal injury.
4.
5.
dress properly. do not wear loose clothing or jewelry. contain long hair.
keep your hair, clothing, and gloves out of the way of the jaws. Loose
clothes, jewelry, or long hair can be caught in moving parts.
do not overreach. keep proper footing and balance at all times. Proper
footing and balance enables better control of this product in unexpected situa-
tions.
6.
7.
use safety equipment. always wear eye protection. Always wear ANSI-ap-
proved safety goggles when working with this tool.
use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
8.
do not force the product. use the correct product for your application.
The correct product will do the job better and safer at the rate for which it is
designed. Do not force the product and do not use the product for a purpose for
which it is not intended.
9.
store idle products out of reach of children and other untrained persons.
This product is dangerous in the hands of untrained users.
10.
11.
never aim the staple gun at any person, child or animal.
Maintain this product with care. Do not use a damaged product. Tag dam-
aged products “Do not use” until repaired.
12.
check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the product’s operation. if damaged,
have the product serviced before using. Many accidents are caused by
poorly maintained products.
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 3
13.
14.
use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one product may become hazard-
ous when used on another product.
when servicing a product, use only identical replacement parts. Follow
instructions in the “inspection, Maintenance, And cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
15.
Maintain labels and nameplates on the product. These carry important in-
formation. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
16.
17.
Maintain a safe working environment. Make sure there is adequate surround-
ing workspace. Do not use this product in a damp or wet location.
always keep hands away from work piece. This Staple Gun has enough
power to force a staple through skin causing serious injury.
speciFicatiOns
Stapler Dimensions
Trigger
6-5/16” x 5-1/2” W x 1-3/16” diameter
Palm Squeeze type
Fastener Types Included Standard staples, brad nails and U-shaped staples
Magazine
Spring loaded slide strip
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
list of contents
part(s)
description
Q’ty
1
Staple Gun
Standard
Staples
(500) T50, 3/8” crown x 5/16” L
500
Brad Nails
(500) 3/8”
500
500
U-Shaped
Staples
(500) 1/4” crown x 1/2” L
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 4
set up instructiOns
read the entire iMpOrtant saFety inFOrMatiOn section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
loading the staples
Figure 1
Push in and down to release the
Staple Channel Latch.
1.
Push the End Clip forward and down to release the Staple Channel Latch. Pull
out the Staple Channel-see Figure 1.
Figure 2
Standard
staple
U-Shaped
staple
Brad
2.
Load the staples or brad nails into the Staple Channel. Each of the fasteners is
to be loaded into the Staple Channel with its sharp end facing the base of the
Staple Channel-see Figure 2.
Staples are to be inserted into the center of the Staple Channel as shown in
Figure 2. Brad nails are to be inserted on either side of the Staple Channel, as
in Figure 2, but not placed in the center of the Staple Channel.
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 5
Figure 3
Depth Adjustment
Knob (1)
3.
To adjust force that will be exerted on the fastener to drive it deeper into the
work piece, use the Depth Adjustment Knob located at the top of the Staple
Gun-see Figure 3. Turn the Depth Adjustment Knob clockwise to increase
the force to drive the fastener, and counterclockwise for less force driving the
fastener.
Operating instructiOns
read the entire iMpOrtant saFety inFOrMatiOn section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
general operating instructions
1.
2.
Push the End Clip forward and down to release the Staple Channel latch. Pull
out the Staple Channel-see Figure 1.
Insert a full strip of fasteners into the Staple Channel. Push the Staple Channel
back into the Staple Gun Body (1). Make certain that it is pushed all the way
back into place before operating the Staple Gun.
3.
Determine whether or not the object being stapled will necessitate extra force
from the Staple Gun. This will depend primarily on the thickness of the item be-
ing stapled. For instance, a large pad of papers will need more force than one
or two sheets being stapled together.
4.
5.
Set the Depth Adjustment Knob (1) accordingly.
Place the item to be stapled below the Driver located on the front of the Staple
Gun.
6.
7.
Grasp the Staple Gun with your fingers inserted into the opening in the Hous-
ing (8) and your palm resting on the Handle (2). Squeeze and pull down on the
Handle (2) to fire a fastener.
Test the Staple Gun using a scrap work piece. Make certain that you have the
Depth Adjustment Knob (1) set correctly, and that the fasteners are placed as
you desire.
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 6
Maintenance and serVicing
cleaning and removing the staple channel
1.
2.
Push the Retaining Clip at the front of the Staple Gun forward to release the
Staple Channel. Pull the two tabs (located midpoint on the bottom of the Staple
Gun) toward the back of the Staple Gun.
The Staple Channel is now free of the Staple Gun and can be cleared of any
jammed fasteners and debris.
cleaning, maintenance, and lubrication
1.
2.
BeFOre eacH use, inspect the general condition of this product. Check for
loose screws, cracked or broken parts and any other condition that may affect its
safe operation.
Remove dirt and debris from the Staple Gun using a clean, soft cloth. Do not
use flammable corrosive or abrasive solvents to clean the Staple Gun.
trOuBlesHOOting
problem
Staple Gun does not staple
possible causes
probable solutions
1. Staples not loaded
1. Verify that staples are loaded into
the Magazine Unit flat and with
prongs facing upward.
correctly.
2. Magazine Unit not fully
and properly inserted into
Staple Gun.
2. Check that Magazine Unit is fully
inserted.
3. Lever not pulled
completely up and then
fully pressed down.
Stapler jams during operation 1. Staples jammed in
1.
2.
Pull out the Staple Channel.
channel.
Remove jammed fasteners
from the channel. You may
need to use long-nosed pli-
ers (not included).
3.
4.
Make certain that you are
using correct size fasteners.
Replace Staple Channel.
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 7
please read tHe FOllOwing careFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN
FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
parts list
part
description
Depth Adjustment Knob
Handle
Q’ty
part
description
Staple Tab
Q’ty
1
2
3
4
1
1
1
1
5
6
7
8
1
1
1
Staple Channel Latch
Retaining Clip
Housing
Handle Ring
Staple Channel
parts diagraM
1
2
8
3
7
6
5
4
SKU 96755
For technical questions, please call 1-800-444-3353.
Page 8
|