®
FRAMING NAILER
34 DEGREE & 28 DEGREE MAGAZINE ANGLES
Models 91053, 91054, 92147, & 92185
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
5.
6.
Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are certain applications for which
this tool was designed. It will do the job better and more safely at the rate for
which it was intended. Do not modify this tool and do not use this tool for a pur-
pose for which it was not intended.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear
are recommended when working. Wear restrictive hair covering to contain long
hair.
7.
8.
Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines or air hoses.
Use eye and ear protection. Always wear ANSI approved impact safety
goggles and appropriate hearing protection. Wear a full face shield if you
are producing metal filings or wood chips. Wear an ANSI approved dust
mask or respirator when working around metal, wood, and chemical dusts
and mists. Other people in the work area must also wear ANSI approved
impact safety goggles.
9.
Maintain tools with care. Keep tools clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords
and air hoses periodically and, if damaged, have them repaired by an authorized
technician. The handle must be kept clean, dry, and free from oil and grease at
all times. Do not operate a tool if any portion of the tool’s operating controls are
inoperable, disconnected, altered or not working properly.
10.
11.
12.
Disconnect Air Hose and release any built-up air pressure. Never service the
Nailer, clear jams, or disassemble with the air hose attached. Always release any
built-up air even after disconnecting hose. Disconnect the Nailer when not in use.
Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before attaching to
an air source.
Avoid unintentional starting. Be sure the trigger is in the Off position when not
in use and before plugging in. Do not carry any tool with your finger on the trig-
ger, whether it is attached to an air source or not. Do not point the tool towards
yourself or anyone whether it contains fasteners or not.
13.
Stay alert. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
14.
Check for damaged parts. Before using any tool, any part that appears dam-
aged should be carefully checked to determine that it will operate properly and
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 3
perform its intended function. Check for alignment and binding of moving parts;
any broken parts or mounting fixtures; and any other condition that may affect
proper operation. Any part that is damaged should be properly repaired or re-
placed by a qualified technician. Do not use the tool if the trigger does not oper-
ate properly.
15.
16.
Guard against electric shock. Prevent body contact with grounded surfaces
such as pipes, radiators, ranges, and refrigerator enclosures.
Replacement parts and accessories. This product is to be repaired and ser-
viced only by a qualified technician. When this product is serviced, only identical
replacement parts should be used. Use of any other parts will void the warranty.
Only use accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
17.
18.
Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes
are impaired while taking drugs. If there is any doubt, do not operate the tool.
Use proper size and type extension cord. If an extension cord is required, it
must be of the proper size and type to supply the correct current to the compres-
sor without heating up. Otherwise, the extension cord could melt and catch fire,
or cause electrical damage to the tool. Check your air compressor’s manual for
the appropriate size cord. It is also possible that the use of an extension cord
may cause your circuit breaker to trip or your panel fuse to break. If this happens,
either use the compressor without an extension cord or find a larger amperage
circuit to use.
19.
Maintenance. The maintenance outlined in the maintenance section should be
performed regularly. For your safety, this product should be serviced or repaired
regularly only by a qualified technician.
20.
21.
Compressed air only. Never use combustible gas as a power source.
Do not load nails with the trigger or safety depressed. Unintentional
firing may occur. Do not load nails when the air hose is connected to
the tool. Always assume the tool contains fasteners.
22.
23.
Disconnect air supply before loading the Nailer. Before reloading (or making
any adjustments to) the Nailer, make sure the compressed air is disconnected.
Fire fasteners into an appropriate work surface only. Do not attempt to fire
fasteners into surfaces too hard to penetrate. Do not drive fasteners on top of
other fasteners, or at too steep an angle. Fasteners can ricochet causing per-
sonal injury. Never fire the Nailer into the air, or point it toward yourself or another
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 4
person. Always wear ANSI approved safety goggles during use, maintenance,
and reloading.
24.
25.
Do not fire fasteners too close to the edge of a workpiece. They may split the
workpiece and fly free, causing personal injury.
Take caution, as some woods contain preservatives such as copper chro-
mium arsenate (CCA) which can be toxic. When working with these materials
extra care should be taken to avoid inhalation and minimize skin contact.
26.
WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contain chemicals known (to the State of
California) to cause cancer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
* Lead from lead-based paints
* Crystalline silica from bricks and cement and other masonry products
* Arsenic and chromium from chemically treated lumber.
(California Health & Safety Code § 25249.5, et seq.)
26.
27.
Stay within air pressure capacity. Never operate the Nailer above 125 PSI.
Hold tool away from head and body. During operation the Nailer may kick back
causing injury.
28.
29.
Transport Nailer safely. Always disconnect air supply when moving the tool in
the workplace. Carry the tool by the handle to avoid contact with the trigger.
Avoid working alone. If an accident happens, an assistant can bring help.
Note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage. Extension cord usage may also affect the tool
performance.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It must
be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure all parts shown in the Parts List on page 12
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number on the cover of this manual as soon as possible.
REV 11/06
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 5
Operation
For best service, you should incorporate an oiler, regulator, and inline filter, as
shown in the diagram below. Hoses, couplers, oilers, regulators, and filters are all avail-
able at Harbor Freight Tools.
TO
ROOFING
NAILER
1.
To connect this tool, we recommend you use the included quick connector.
Note: If you are not using an automatic oiler system, before operation, add a few
drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after
each hour of continual use.
2.
3.
Set the air pressure on your compressor from 75-125 PSI. Do not exceed the
maximum air pressure.
Check the air connection for leaks.
Note: The amount of air pressure effects how deep the nails/staples will be
driven. It is suggested that you experiment on scrap material.
4.
Check the air connection for leaks and disconnect the Nailer/Stapler.
Testing the Full Sequential Safety Trip Mechanism
Warning: Even though the nailer should be empty during this procedure,
ALWAYS point the nailer at a piece of scrap wood when testing.
1.
2.
3.
Make sure the tool is disconnected from the power supply.
Completely empty the Magazine (74) of nails.
The Nailer should not fire if the Lower Safety (32) is not depressed against the
workpiece.
REV 11/06
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 6
4.
5.
6.
Make sure the Trigger (48) and Lower Safety (32) move freely, without sticking -
see the illustration below.
Connect the air supply to the tool at the Quick Connector (87). Set the regulator at
the recommended 75 to 125 PSI.
Test the tool by depressing the Lower Safety (32) against the workpiece without
pulling the Trigger (48). The Tool must not cycle (fire). If it cycles (fires), stop
immediately and have it repaired by a qualified service technician.
7.
8.
Hold the tool away or off of the workpiece. The Lower Safety (32) of the tool
should return to its original position. Squeeze the Trigger (48). The tool should
not cycle (fire). If the tool fires, stop immediately and have it repaired by a
qualified service technician.
Depress the Lower Safety (32) against the workpiece and squeeze the Trigger
(48). The tool must cycle (fire) only once. Release the Trigger and squeeze it
again. The tool must not cycle (fire). With the Trigger held, carefully lift the
nailer and press it against the workpiece again. The tool must not cycle (fire).
If it fails to perform in the manner explained in bold, have it repaired by a qualified
service technician.
QUICK CONNECTOR (87)
TRIGGER (48)
LOWER SAFETY (32)
TRIGGER (48)
LOWER SAFETY (32)
REV 11/06
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 7
Loading Nails
ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN
RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL.
Other people in the work area must also wear ANSI approved impact safety
goggles.
Warning! Make sure the Nailer is not attached to the air hose whenever loading the
tool.
1.
2.
Slide the Tab (64) back and the Latch (78) will hold it in place.
Holding the nailer with the nose pointing slightly down, load a stick of nails into the
top slot.
3.
While holding the Tab back, carefully press the Latch. BE CAREFUL. When you
press the Latch (78), theTab (64) will spring forward with force. Slowly and cautiously
allow the tab to slide forward.
NAILS (91)
TAB (64)
(PULLED
BACK)
LATCH
(78)
MAGAZINE
(74)
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 8
Operating the Nailer
1.
Attach the Nailer to the air supply at the Quick Connector (87). Start your com-
pressor, and check the pressure making sure it is set at the recommended 75-125
PSI and not to go over the maximum PSI.
2.
3.
Rotate the Exhaust Cover (3) so that the exhaust air blast will be directed away
from the operator.
To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if
the nose is not depressed. Once depressed, gently and briefly squeeze the
Trigger (48) once. Do not fire repeatedly. Nails could bounce off of one an-
other, damaging the workpiece or causing PERSONAL INJURY.
4.
5.
6.
Do not press the Lower Safety (32) of the Nailer against the work surface with
excessive force. Allow the tool to do the work. Always allow the tool to recoil off
the workpiece.
Caution: While working, dirt and sawdust may build up on the Lower Safety (32)
of the Nailer. This can prevent normal operation. Remove buildup using com-
pressed air.
When finished using the Nailer, always disconnect the tool from its compressed
air supply. Empty the Magazine (74) completely of nails. Attempt to fire the
Nailer into a piece of scrap wood to ensure it is disconnected and is incapable of
firing any nails.
7.
Make sure to store the Nailer in its Carrying Case in a clean, dry, safe location
out of reach of children.
EXHAUST COVER (3)
QUICK CONNECTOR (87)
TRIGGER (48)
LOWER SAFETY (32)
WORK SURFACE
REV 11/06
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 9
Anytime any maintenance or repairs are done (including clearing jams),
FIRST:
1.
2.
3.
Disconnect the Nailer from the air hose.
Empty the Magazine (74) completely.
Attempt to fire the Nailer into a piece of scrap wood to ensure that it is discon-
nected and is incapable of firing any nails.
Clearing Jams
1.
Occasionally a Nail may become jammed in the firing mechanism of the Nailer,
making the tool inoperative.
2.
3.
To remove a jammed nail, disconnect the Nailer from its compressed air supply.
Slide the Tab (64) back and empty the Magazine (74) completely of Nails. At-
tempt to fire the Nailer into a piece of scrap wood to ensure it is disconnected
and is incapable of firing any nails.
Use a pair of needle nose pliers (not included) to remove the jammed nail (usu-
ally from the Upper Safety (28) and/or Lower Safety (32) areas). While holding
the Tab back, carefully press the Latch. BE CAREFUL. When you press the
Latch (78), the Tab (64) will spring forward with force. Slowly and cautiously allow
the tab to slide forward.
4.
5.
6.
7.
Reconnect the air supply hose to the tool.
Press the Lower Safety (32) of the Nailer against a piece of scrap wood.
Test fire the Nailer several times, checking for proper operation.
If the Nailer is properly firing, you can continue to use the Nailer. Disconnect the
air supply to the Nailer, and reload the Nails. Then, reconnect the air supply and
continue working.
8.
When finished working, Disconnect the air supply. Remove the Nails. Then,
store the Nailer and nails in a location out of children’s reach.
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 10
Anytime any maintenance or repairs are done, FIRST:
1.
2.
3.
Disconnect the Nailer from the air hose.
Empty the Magazine (74) completely.
Attempt to fire the Nailer into a piece of scrap wood to ensure that it is discon-
nected and is incapable of firing any nails.
Inspection, Maintenance, and Cleaning
1.
Inspect the Nailer frequently and lubricate periodically with Pneumatic tool oil,
then wipe dry. Do not use detergent oil or additives as these lubricants will cause
accelerated wear to the internal seals.
2.
Inspect the air supply filter, if present, before each use and clean or replace as
necessary. Dirt and water in the air supply filter are major causes of pneumatic
tool wear. Use a filter/oiler for better performance and longer tool life. The filter
must have adequate flow capacity for the specific application.
3.
4.
5.
Clean the Nailer with a clean, wet cloth. Then dry.
Store the unit in a clean and dry location out of children’s reach.
All maintenance, service, or repairs not listed in this manual are only to be
attempted by a qualified technician.
Please Read the Following Carefully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
NOTE:
Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 11
Parts List
Part
1
Description
Set Screw
Shim
Part
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Description
Part
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Description
Trigger
Part
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
Description
Internal Hex Bolt
Support
O-Ring
Gasket
2
O-Ring
3
Exhaust Cover
Internal Hex Bolt
Shim
Body
Trigger Plate
Spring Pin
Bushing
4
Safety A
Magazine
5
Safety Spring
Lock Nut
O-Ring
Set Screw
6
Spring Washer
Flat Washer
Deflector
Packing
Trigger Valve Body
Pin
Spring Pin
Internal Hex Bolt
Latch
7
Internal Hex Bolt
Safety B
8
O-Ring
9
Safety Sleeve
Shelter
O-Ring
Latch Bushing
Latch Spring
Nail Guide
Lock Nut
10
11
12
13
14
15
16
17
19
20
21
22
23
24
Gasket
O-Ring
Inner Lining
Spring
Internal Hex Bolt
Outer Bumper
Inner Bumper
Spring Pin
Trigger Valve Piston
O-Ring
O-Ring
Compression Spring
O-Ring
Tail Hanger
Internal Hex Bolt
O-Ring
O-Ring
O-Ring
Driver Guide Bushing
O-Ring
Trigger Valve Stem
Inner Trigger Valve Seat
Tab
Head Valve Piston
Seal
End Cap
Driver Guide
Spring Washer
Internal Hex Bolt
Safety Guide
Spring Pin
Quick Connector
Plug
O-Ring
Pin
Driver Unit
Cylinder
Roller
Spring Washer
Flat Washer
Spring
Pusher Spring
Semicycle Soc.Hd.Screw
Flat Washer
Roller Seat
O-Ring
Seal
Pin
Flat Washer
Internal Hex Bolt
Lining Ring
Spring Pin
Assembly Diagram
91053, 91054
92147, & 92185
Skus
For technical questions, please call 1-800-444-3353.
Page 12
|