JUMBO TRICYCLE
WITH PNEUMATIC TIRES
94142
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
9. Use the right Tricycle for the situation. There are certain applications for which this
Tricycle was designed. Do not modify this Tricycle and do not use this Tricycle for a
purpose for which it was not intended.
10. Only one person allowed on the Tricyle at any time. Only one seated rider should be on the
Tricycle at a time. No other passengers should be standing on the rear of the frame, or sitting
on the handlebars.
11. The Tricycle is meant for off-road use and is not for use as transportation on main
streets and highways.
12. Do not exceed the maximum weight capacity of 250 Lbs.
13. Always make sure tires are properly inflated (see page 2).
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Tricycle with Pneumatic Tires, check to make sure all parts listed on page 5
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Assembly
Your Rolling Tricycle with Pneumatic Tires will require complete assembly. It is important that you
read the entire manual to become familiar with the product BEFORE you assemble and use the
Tricycle. Before assembling the Tricycle be sure that you have all parts described in the Parts List
and Assembly Diagram located on the last pages of this manual.
THE RIDER OFTHETRICYCLE MUST BE AT LEAST 48”TALLTO PROPERLY REACHTHE PEDALS.
Handlebars
1.
To attach the Handlebar (1), loosen Nut (31) and slide out Bolt (33) and Washer (32).
Insert Handlebar (1)-see Figure 1. Adjust Handlebar so that it is centered on the Stem (8)
and set at the angle that is most comfortable for the rider. Now insert Bolt (33) with
Washer (32) and thread on Nut (31). Tighten into place. Apply pressure to the
Handlebars(1) to make certain that they do not rotate.
2.
3.
Slide a Grip (2) onto the end of each Handlebar (1).
Insert the Handlebar (1) and Stem (8) down through the Locknut (5), Upper Cap (7),
and Bearing Ring (36) and into the Frame (13).
Figure 1
Lock Bolt (3)
Handlebar (1)
Bolt (33)
Washer (32)
Nut (31)
Stem (8)
SKU 94142
For technical questions please call 1-800-444-3353.
Page 3
CAUTION:
Make certain that the Stem (8) and Handlebar (1) are set at an appropriate height for
the rider. Make certain that the Stem (8) is not raised beyond where it is secure in the
Frame (13). Make certain it is stable and tightly in place before riding the Tricycle.
4.
To raise or lower the Stem (8), use a hex wrench to loosen the Lock Bolt (3). Gently pull up
on the Stem (8) or push it down until it is at the desired height. Make certain that it is
centered with the frame and Front Wheel (26). Tighten the Lock Bolt (3) into place-see
Figure 1.
Attaching the Seat and Seat Bracket
1.
2.
Line up the Seat Bracket (11) with one of the two sets of holes in the frame-see Figure 2.
Insert Bolt (9) and thread on Lock Nut (34).
If desired, the Seat (10) can be rotated up and down or moved forward or backward by
loosening the Nut located directly under the Seat (10).
Figure 3-Rear Wheel
Figure 2-Seat and Seat Bracket
Nut under
Seat (10)
Seat
Bracket (11)
Cotter
Pin (14)
Axle (35)
Attaching Rear Wheels
1.
1.
Slide one Rear Wheel (15) onto the Rear Axle (35). Slide on Washer (16) and insert Cotter
Pin (14) through the outside hole in the Axle (35)-see Figure 3. Repeat for second Rear
Wheel (15)-see Figure 3.
Replacing Front Wheel
To fix or replace the Front Wheel (26), first remove Screws (24) from Front Wheel (26) rim-
see Figure 4 and Assembly Diagram on page 6. Pull out Front Axle (25) and remove the
Front Wheel (26). To put it back in position, line up Front Wheel (26) with holes in the
Fork (29). Insert Front Axle (25), and thread in Screws (24).
Figure 4
Fork (29)
Front
Wheel (26)
Screw (24)
SKU 94142
For technical questions please call 1-800-444-3353.
Page 4
Inserting the Pin
1.
The Tricycle can be set-up to carry a small cart or trailer (neither is included) behind it by
attaching them to the rear of the Tricycle. Unhook the Pin (12) from the rear of the Tricycle.
Attach the cart to the Tricycle, and insert the Pin (12) back through the carrier and Tricycle-
see Figure 5.
Figure 5
Pin (12)
Maintenance
1.
2.
Check the tire pressure often. Make certain that tire PSI is correct (see Technical
Specification on page 2). A low tire inflation will force the rider to exert greater energy to
move the Tricycle. The tires may wear prematurely if the proper tire pressure is not
maintained.
Wheels and Hubs should be greased periodically.
Parts List
Part # Description
Quantity Part # Description
Quantity
1
2
3
4
5
6
7
8
Handlebar
Grip
Lock Bolt
Sleeve
Lock Nut
Lock
Upper Cap
Stem
Bolt M6
Seat
Seat Bracket
Pin
Frame
Cotter Pin
Rear Wheel
Washer
Nut M6
Washer
Crank (left)
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
4
2
2
1
19a
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Crank (right)
Pedal
Screw
Nylon Cap
Pin
Screw M6
Front Axle
FrontWheel
Lower Cap
Bearing Holder
Fork
Bearing
Nut M8
Washer
Bolt
Lock Nut
Rear Axle
Bearing Ring
Bolt M8
1
2
2
2
2
4
1
1
1
1
1
2
1
1
1
1
1
1
1
9
10
11
12
13
14
15
16
17
18
19
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Rev. 05/06
Page 5
SKU 94142
For technical questions please call 1-800-444-3353.
Parts and Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Rev. 05/06
SKU 94142
For technical questions please call 1-800-444-3353.
Page 6
|