LED LCD TV
OWNER' S MANUAL
MODEL: LE32B50
Please READ this manual carefully
before operating your TV, and retain
it for future reference
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
CAUTION
2) Keep these instructions.
RISK OFELECTRIC SHOCK
DO NOTOPEN!
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install
in accordance with the instructions.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
8) Do not install near any heat sources such as
radiations, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized plug. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
The symbol indicates that dangerous
voltages constituting a risk of electric shock
are present within this unit.
The symbol indicates that there are
important operating and maintenance
instructions in the literaturaccompanying this
unit.
10) Protected the power cord from being walked
on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
WARNING:
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
11) Only use attachments/accessories specified
by the manufacturer.
WARNING:
The batteries shall not be exposed to
excessive heat such as sunshine, fire or the
like.
12) Unplug this apparatus during lighting
storms or when unused for long periods of time.
13) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user accessible
parts. When servicing use only
14) Mains plug is used as the disconnect device,
the disconnect device shall remain readily
operable.
identical replacement parts.
15) The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted
candles, should be placed on the apparatus.
17) Attention should be drawn to the
environmental aspects of battery disposal.
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from
18) The use of apparatus in moderate climate.
19) The apparatus shall not be exposed to
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
the apparatus.
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose
the television receiver to rain or moisture.
Do not place your television on an unstable cart, stand,
shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
When the television receiver is not used for an
extended period of time, it is advisable to disconnect
the AC power cord from the AC outlet.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of
electrical components.
Avoid exposing the television receiver to direct sunlight
and other sources of heat. Do not stand the television
receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
Dim:515*320mm(不
包
括
底
座
）
Do not trap the power supply cord under the television
receiver.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
-3-
INTRODUCTION
Accessories
Main features
①
②
③
④
5
Used as Television, display terminal, PC display；
High luminance, wide viewing angle；
Can store 200 TV programs；
HDMI interface；
Infrared Remote Controller............1
Battery(AAA)...............................2
User’s Manual...............................1
Multi-Media player (USB);
Main parameter
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
32 inch
1366x768
16 : 9
TV System
PAL/BG PAL/I PAL/DK SECAM/BG SECAM/DK
PAL/NTSC/SECAM
Video Signal System
Receiving Channel
1-200
Input Power Voltage
Power consumption
AC 100-240V 50/60Hz
50W
（THD 7%） 2x8W
Audio Output Power
Signal Input/Output
Analog RGB(VGA) x 1
High-Definition Multimedia Interface (HDMI) x 2
Composite Video Input x 1
Composite Video output x1
Audio Input x 2
Headphone x 1
YCb (Pb)Cr (PR) x 1
USB x 1
RF x 1
Composite Video input >=350
Horizontal definition（TV line）
Y Cb(Pb ) Cr(Pr)
>=400
-4-
INSTALLATION
KEYBOARD
Front panel
1
2
3
4
5
SOURCE
MENU
CH+
CH-
VOL-
VOL+
STANDBY
1
3
2
30 30
USB
MUTE
PICTURE AUDIO ASPECT SLEEP
1．SOURCE：
Display the input source menu.
2．MENU：
Display main MENU.
3．CH+/CH-
DISPLAY
MENU
RECALL
INPUT
OK
CH.LIST
VOL-
EXIT
CH+
VOL+
CH-
PLAY/PAUSE STOP
PREV
NEXT
In TV mode，press“CH+”or“CH-”to change
the channel up and down.
In MENU mode, press “CH+”or“CH-”to select
items.
1: Remote control sensor.
2: Indicator LED: BLUE
RED
4．VOL+/VOL-
Adjust sound level.
POWER ON.
STANDBY.
In MENU mode, press“VOL+”or“VOL-”to
adjust the item that you selected.
5. STANDBY
3: Key board
Press this button to turn the unit ON from
STANDBY mode.
Press it again to turn the set back to STANDBY.
REAR AV Connections
AV INPUT
L
AV OUTPUT
L
VIDEO
R
VIDEO
R
AC-INPUT
100-240V~50/60Hz
All the terminals are(from left to right):
AC POWER SOCKET, AV INPUT, AV OUTPUT.
Note: VIDEO and YPbPr share one audio channel.
REAR AV Connections(SIDE)
USB
HDMI2
HDMI1
HEADPHONE
PC AUDIO
VGA
RF
Y
Pb
Pr
All the terminals are (from left to right):
USB, HDMI2,HDMI1, YPbPr INPUT, HEADPHONE, PC AUDIO, VGA, RF.
Note: When HDMI port get DVI signal, the audio signal receives from the PC
Audio channel.
-5-
INSTALLATION
ANTENNA
Note:
Aerial connections: IEC(female).
Input impendance: 75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are
set to Power off.
1.Connect VGA and audio cable.
2.Connect the power cord.
3.Power on the TV, switch to PC mode.
4.Power on the PC.
This sequence is very important.
USB
HDMI2
HDMI1
HEADPHONE
PC AUDIO
VGA
RF
Y
Pb
Pr
-6-
INSTALLATION
AV INPUT
L
AV OUTPUT
L
VIDEO
R
VIDEO
R
AC-INPUT
100-240V~50/60Hz
PRESET MODE (PC)
V.Freq.(Hz)
H.Freq.(KHz)
RESOLUTION
1
2
3
800*600
60
37.88
1024*768
1360*768
60
60
48.36
47.7
NOTE: PC V.Freq.(Hz) not more than 60Hz.
PRESET MODE (HDMI)
V.Freq.(Hz)
H.Freq.(KHz)
RESOLUTION
1
2
3
4
5
800*600
1024*768
1360*768
1280*768
1920*1080
60
37.88
60
60
60
60
48.36
47.7
47.3
67.5
-7-
INSTALLATION
AV EQUIPMENT
This TV provides one group of AV ,one group of YPbPr for convenient connection to VCR, DVD
or other video equipment. Please refer to the owner's manual of the equipment to be connected
as well.
You can use the input terminals on TV set rear as follows.
USB
HDMI2
HDMI1
HEADPHONE
PC AUDIO
VGA
RF
Y
Pb
Pr
G
B
R
VIDEO EQUIPMENT with YPbPr
HDMI
W
R
G
B
R
Y
R
W
R
B
G
Yellow (video)
Red (audio R)
White(audio L)
Red(Pr or Cr)
Blue(Pb or Cb)
Green(Y)
R
W
AV INPUT
L
AV OUTPUT
L
VIDEO
R
VIDEO
R
AC-INPUT
100-240V~50/60Hz
W
R
Y
W
R
Y
VIDEO EQUIPMENT
VIDEO EQUIPMENT
W
R
W
R
Y
TO VIDEO
INPUTS
TO VIDEO
OUTPUTS
TO AUDIO INPUTS
TO AUDIO OUTPUTS
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,
video game or stereo system, etc.....
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080P.
Note:
1.AV and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the
audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys
nonstandard signal.
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT
signal is AV; other sources have no AV OUT signal.
-8-
REMOTE CONTROLLER
The remote control cannot be operated unless the batteries are properly loaded inserted.
When using the remote control, aim it at the remote control sensor on the TV.
Function introduction
1
2
1.Press to turn on and off the TV.
2.USB:Press to launch the USB multimedia mode
3.Switches the TV sound on or off.
4.Press repeatedly to cycle through the available
picture modes.
USB
MUTE
3
PICTURE AUDIO ASPECT SLEEP
13
14
4
5
5.Press to cycle through the different sound mode
settings
6.Press to change a channel.
6
7.Press to display the TV status information on the bottom.
8.Press to open the on-screen menu
9.Open the channel list in TV mode.
15
16
RECALL
INPUT
7
8
DISPLAY
MENU
10.Press CH+ or CH- to go to the next or previous
channel. Press VOL+ or VOL- to increase or
decrease the volume.
11. Play/Pause Stop
Previous
Next
17
18
12.Be used in programme edit:
Red: Delete
OK
Green: Rename
Yellow: Move
Blue: Skip
CH.LIST
VOL-
EXIT
CH+
9
19
VOL+
CH-
13.Press to display the sleep timer option.
14.To change the picture aspect ratio: Auto,4:3,
16:9,Zoom, Zoom2.
15.Press to go to the last viewed channel.
16.Show the input source menu.
10
11
12
PLAY/PAUSE STOP
PREV
NEXT
17.Press to confirm selections in an on-screen menu
or to open a submenu.
18.To move within the menu.
19.Exit On Screen Display.
-9-
TV OPERATION
1. CHANNEL MENU
The first item of the MENU is channel menu ( for
TV source only).
Delete
Delete
You can search channels and edit programs here.
Press
to choose the program.
Press
and press
to move, press OK button to confirm,
to adjust.
Press red button, the program will delete.
Rename
Rename
Move the cursor to the program, press
green button to rename the program.
Auto Tuning
Sound System
Manual Tuning
Programme Edit
Press
move the cursor.
to choose the character. Press
to
CHANNEL
Software Update(USB)
<
>
Press MENU button to exit edit, Press EXIT to exit
the menu.
Note: The TV programs name only can be 5 characters.
Move
Move
Move the cursor to the program, press
yellow button, it will show yellow cursor, Press
to move the program.
1).Auto tuning:
Search all the TV channels automatically.
Skip
Skip
2). Sound System：
You can change the sound system.
Press
to choose the program, press
blue button to skip this program, The icon
show on the right side of the program.
will
3). Manual tuning:
You can search the TV channels and fine tune the
channels, then storage the channels you selected.
Choose the skipped program, press the blue button
again, you can cancel the skip, Then the icon
disappear.
will
Manual Tuning
_
Storage To 2
+
5). Software update(USB):
Current CH 2
Search
Update the TV set' s software by USB.
2. PICTURE MENU
The second item of the MENU is PICTURE MENU.
You can adjust picture effect here, such as contrast,
brightness, etc.
Fine-Tune
Press
to move, press OK button to confirm,
to adjust.
Frequency 874.37 MHz
and press
Save
MENU
NOTE:
Picture Mode
Standard
Press red button to storage to channels
after manual tuning .
Color Temperature
Aspect Ratio
Noise Reduction
Screen
4). Program Edit:
You can Delete, Rename, Move, or Skip any programs.
PICTURE
<
>
Programme Edit
1
2
3
NOTE:
1).Tint is available in NTSC system only.
2).There are four color temperature modes
can be selected, such as medium, warm, cool, and user.
3).Screen is available in PC mode only, which
can adjust horizontal position, vertical position,
size and phase.
Skip
MENU
Delete
OK
Rename
Move
-10-
TV OPERATION
3. SOUND MENU
The third item of the MENU is the SOUND
MENU.
OSD Language
English
Restore Factory Default
You can adjust the sound effect here such as
treble, bass, balance etc.
Blue Screen
OSD Blend
Press
to move, press OK button to confirm,
to adjust.
OPTION
<
>
and press
Sound Mode
Balance
Standard
Auto Volume
Surround Sound
NOTE:
SOUND
<
>
Restore factory default will clear all the programs
and Reset all the settings to default value.
6. USB FUNCTION
You must enter the Source menu first,then choice the
USB and press OK button,the USB menu will appear.
Input Source
Note:
Auto volume: only available when the input
signal volume is too large or distortion.
TV
YPBPR
PC
4. TIME MENU
HDMI1
HDMI2
AV
The forth item of the menu is the TIME MENU
You can adjust the clock, power on/off time,
sleep time etc.
Press
to move, press OK button to confirm,
to adjust.
USB
and press
OK
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
TIME
<
>
USB 2.0
PHOTO
MUSIC
MOVIE
TEXT
NOTE:
Within 15 minutes there is no signal, the TV
will auto sleep.
Once you power off the TV set by AC, the clock time
will be reset.
Please make sure that the USB device have plugged in
the slot. There are four type media item can be selected,
such as photo, music, Movie and text. Select the type
media item by pressing
the disk selection menu.
, press OK button to enter
5. OPTION MENU
The fifth item of the MENU is the OPTION MENU.
You can adjust the OSD language, Restore factory
default, Blue Screen or OSD Blend.
In the movie mode, when you use FB, FF function, The
audio may be pause in several seconds to synchronize
the audio signal and video signal.
In text mode, press
to make page up and page down.
NOTE:
When the USB device isn't supported, it may be that the
power of the USB device isn't enough.
-11-
TV OPERATION
Press
to select the function icon, press OK button to
confirm the function.
1/1
Press
NOTE:
or EXIT button to exit the control bar.
You can adjust the audio track, subtitle, or program in
the Info menu while Playing the video file.
Choose the Info icon and press OK can display the Info
MENU.
Return
C
Sample1.ts
Press the
to select the right disk and press OK to
Resolution: 720x576
display media files and folder list or choose Return to
back to the media type selection menu.
AudioTrack:
Subtitle:
1/2
1/3
1/6
Program:
1/1
Size:
30574 KBytes
Resolution: 688x412
R
AudioTrack: 1/2
Subtitle:
1/3
1/5
Program:
Size: 511457 KBytes
M
Sample1.ts
Sample2.ts
Close
Sample1.ts
Sample3.ts
Sample4.ts
Select the media file by pressing
or
, then
the preview frame will pop up. Press the button
to play the media file in full screen. When the
media file (photo, music, Movie or text type) is
playing, press the OK or Info button can display the
control bar.
Music function need to put music and picture in the
same folder.
-12-
TV OPERATION
Hotel Mode:
Please press source key first,and then press number key
“1001” to enter into Hotel Mode.
HotelModeOperation
OFF
OFF
100
TV
Hotel Mode Operation
Panel key lock
Maxvolume
Start Source
Start Channel
1
Setup Menu display
Input source change
Save To USB
Yes
Yes
Load
Volume default
0
Hotel Mode Operation: Set Hotel mode on/off.
Panel key lock : Keypad will be locked, when Key Lock
mode is on.
Max volume: Set max volume limitted.This option allows
you to set the Max Volume Level.
Start Source：Choose source, the options as follow:
TV/YPBPR/PC/HDMI1/HDMI2/AV/USB, press the ◄ or ►
button to select the desired source.
Start Channel : In TV mode, you can select a channel
number to be set as the TV present channel. Press the ◄ or
► button to select the desired channel number .
Setup Menu display :Main menu lock , main menu will not
display when set to “No”
Input source change : Source lock，you can't change the
source, when set to “No”
Save To USB: Backup all TV setting data to USB disk.
(backup file named DATABASE.bin)
Load: Restore this data to TV from USB disk. When
restore is executed，the TV will reboot.
Volume default : Power on default volume, press the ◄ or
► button to select the desired volume.
-13-
TROUBLE SHOOTING
Trouble phenomenon
Picture
Audio
Inspection
antenna position, direction
or connection
Snow
Noise
antenna position, direction
or connection
Ghost
Normal audio
Noise
electronic equipment,car/
motorcycle,fluorescent light
Interfere
Volume(inspect wether the
mute function on the remote
control are started , or audio
system are correct or not)
Normal Picture
Mute
Power cord is not inserted
Power switch is not opened
Contrast and brightness/volume
setup
No picture
No color
Mute
Press standby key on the remote
control for inspecting
Normal audio
color control
Normal audio
or weak
retune channel
Scramble
No color
Audio system
Noise
Special Explanation：The accessories such as remote control is not belongs
to the guarantee。
-14-
|