Grizzly Vacuum Cleaner H0602 User Manual

12V CORDLESS VACUUM  
MODEL H0602  
INSTRUCTION MANUAL  
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN CHINA  
 
Safety Instructions For Power Tools  
9. USE PROPER EXTENSION CORD  
14. MAINTAIN TOOLS WITH CARE.  
for the charger. Make sure your  
extension cord is in good condition.  
Conductor size should be in accor-  
dance with the chart below. The  
amperage rating should be listed on  
the motor or tool nameplate. An  
undersized cord will cause a drop in  
line voltage resulting in loss of power  
and overheating. Your extension  
cord must also contain a ground wire  
and plug pin. Always repair or  
replace extension cords if they  
become damaged.  
Keep tools sharp and clean for best  
and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
15. DISCONNECT TOOLS before ser-  
vicing and changing accessories,  
such as blades, bits, cutters, and  
the like.  
16. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Make sure  
switch is in off position before plug-  
ging in.  
17. USE RECOMMENDED ACCES-  
SORIES. Consult the owner’s man-  
ual for recommended accessories.  
The use of improper accessories  
may cause risk of injury.  
Minimum Gauge for Extension Cords  
AMP  
RATING  
0-6  
LENGTH  
50ft  
16  
25ft  
18  
18  
16  
14  
12  
10  
100ft  
16  
14  
14  
12  
18. CHECK  
DAMAGED  
PARTS.  
7-10  
16  
16  
12  
12  
Before further use of the tool, a  
guard or other part that is damaged  
should be carefully checked to  
determine that it will operate proper-  
ly and perform its intended function.  
Check for alignment of moving  
parts, binding of moving parts,  
breakage of parts, mounting, and  
any other conditions that may affect  
its operation. A guard or other part  
that is damaged should be properly  
repaired or replaced.  
11-12  
13-16  
17-20  
21-30  
10  
No  
10  
10. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neck-  
ties, rings, bracelets, or other jewel-  
ry which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear protective hair cover-  
ing to contain long hair.  
11. ALWAYS USE SAFETY GLASSES.  
Also use face or dust mask if cutting  
operation is dusty. Everyday eye-  
glasses only have impact resistant  
lenses, they are NOT safety glass-  
es.  
No list of safety guidelines can be  
complete. Every shop environment is  
different. Always consider safety  
first, as it applies to your individual  
working conditions. Use this and  
other machinery with caution and  
respect. Failure to do so could result  
in serious personal injury, damage to  
equipment or poor work results.  
12. SECURE WORK. Use clamps or a  
vise to hold work when practical. It’s  
safer than using your hand and frees  
both hands to operate tool.  
13. DON’T OVERREACH. Keep proper  
footing and balance at all times.  
-2-  
H0602 12V Cordless Vacuum  
 
ADDITIONAL SAFETY  
1. Read all instructions and warn-  
7. If charger light fails to come on  
check the incoming power supply. If  
power source is okay, then the fuse  
inside the charger needs replace-  
ment. Charger should be serviced  
by a qualified electrical technician  
only.  
ings on the battery and charger  
before charging the battery.  
2. Charge only using the supplied  
charger and battery. Do not use  
with other batteries, chargers or trim  
saws.  
8. Charger plug has a polarized  
plug (one prong is wider than the  
other). Do not attempt to modify the  
plug. Modifying the plug will result  
in a safety hazard and will void the  
warranty.  
3. Do not expose battery or charger  
to wet or rainy conditions.  
Moisture greatly increases the risk  
of a shock hazard.  
4. Do not touch battery poles with  
any conductive materials. Touching  
any two poles at the same time  
causes a short condition and can  
cause sparks or electrical shock.  
9. Charger is designed to operate at  
110-120 volts. Never try to plug  
into any circuit that is not 110-120  
volts. Never modify or change the  
plug that is attached to the charger  
unit to attempt to plug into 220 volt.  
This can cause serious electrical  
damage to the unit, possible fire or  
explosion.  
5. Do not store battery with conduc-  
tive materials. Storing the battery  
in a box of screws or nails can  
cause shorting across the battery  
poles.  
6. Do not throw battery in fire.  
Combustion of some of the batter-  
ies’ component materials can cause  
toxic fumes and possible explosion.  
BATTERY MUST BE RECYCLED OR DISPOSED  
OF PROPERLY. Consult your local Yellow Pages  
directory under the category “Recycling” to locate a  
battery recycler in your area.  
-3-  
H0602 12V Cordless Vacuum  
 
INTRODUCTION  
Commentary  
We are proud to offer the Grizzly Model  
H0602 12V Cordless Vacuum. The Model  
H0602 is part of a growing Grizzly family  
of fine power tools. When used according  
to the guidelines set forth in this manual,  
you can expect years of trouble-free,  
enjoyable operation and proof of Grizzly’s  
commitment to customer satisfaction.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model H0602 as supplied when the manu-  
al was prepared. However, owing to  
Grizzly’s policy of continuous improve-  
ment, changes may be made at any time  
with no obligation on the part of Grizzly. If  
you have any comments regarding this  
manual, please write to us at the address  
below:  
The Model H0602 12V Cordless Vacuum  
is equipped with a high velocity motor  
capable of handling many clean-up jobs.  
The large collection chamber requires no  
special bags and is easy to empty.  
Vacuum also includes a 12V charging sta-  
tion.  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
Most importantly, we stand behind our  
tools. If you have any service questions or  
parts requests, please call or write us at  
the location listed below.  
We are pleased to provide this manual  
with the Model H0602. It was written to  
encourage safety considerations and  
guide you through general operating pro-  
cedures and maintenance. It represents  
our effort to produce the best documenta-  
tion possible.  
Grizzly Industrial, Inc.  
2406 Reach Road  
Williamsport, PA 17701  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
The Model H0602 was specifically  
designed for vacuuming dust, dirt  
and other small debris. Do not mod-  
ify and/or use this machine for any  
other purpose. Modifications or  
improper use of this tool will void  
the warranty. If you are confused  
about any aspect of this machine,  
DO NOT use it until you have  
answered all your questions.  
Serious personal injury may occur.  
Never leave a battery unattend-  
ed while charging. While charg-  
ing will make the battery and  
charging unit warm, if it  
becomes hot to the touch, dis-  
connect the charger immediate-  
ly. There is a possibility of fire  
hazard. Have the battery and  
charging unit checked by a qual-  
ified electrical service techni-  
cian.  
-4-  
H0602 12V Cordless Vacuum  
 
OPERATIONS  
Getting Started  
First review the contents of your cordless  
tool kit and familiarize yourself with the key  
components.  
3. Occasionally remove and clean the  
elastic filter sleeve from the inside of  
the collection chamber. Allow filter to  
completely dry before using the vacu-  
um.  
Cordless Vacuum  
Battery Pack  
Charging Stand  
Keeping Tools Clean  
The battery in your new cordless power  
tool will not be fully charged when you  
receive it. To maximize the storage capac-  
ity of the battery it should be completely  
discharged, then fully recharged 3-5 times.  
Plastic parts can easily be cleaned with a  
damp cloth, but never use water to clean  
any electrical parts. Solvents should also  
be avoided on plastic because of the pos-  
sibility of damage.  
For optimal life span, completely discharge  
the battery before charging. Follow the  
instructions below to charge your battery.  
Maintenance  
Battery charging with standard charger  
(1 piece charger):  
Your cordless power tool will give you hun-  
dreds of hours of operation time before  
ever needing service. The electrical com-  
ponents of this cordless vacuum are not  
user serviceable. Repair should always be  
undertaken by a qualified electrical repair  
technician.  
1. Plug the charger into an appropriate  
110/120V outlet.  
2. Insert the battery into the charger.  
The battery fits into the oval recess in  
only one way. Do not force the bat-  
tery. Insert until it locks into place.  
3. The red light will come on when the  
battery is inserted. Charge battery for  
3-5 hours.  
Always store the cordless vacuum in a dry  
place.  
4. When the battery is fully charged,  
remove the battery from the charger  
to complete of the charge cycle.  
The battery will require periodic recharg-  
ing, and eventually replacement after it has  
exceeded its recharge life (approximately  
800-1000 recharge cycles). You will notice  
extended charging times or shortened  
operation time as the battery experiences  
more cycles. Refer to the Grizzly catalog  
for replacement batteries.  
Using Your Vacuum  
1. Turn vacuum on by pressing the  
switch at located on the top of the  
unit.  
2. Empty the collection chamber by  
pressing the button located on the top  
of the unit  
-5-  
H0602 12V Cordless Vacuum  
 
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Number’’, which must be clearly posted on the outside as  
well as the inside of the carton. We will not accept any item back without this number. Proof  
of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
2406 Reach Road  
Williamsport, PA 17701  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon.  
-6-  
H0602 12V Cordless Vacuum  
 
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model # H0602 12V Cordless Vacuum  
Order #_______________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
___12" Table Saw  
___12" Jointer  
___Radial Arm Saw  
___Panel Saw  
___Lumber  
___Brass Hardware  
4. How long have you been a woodworker?  
___Paint & Finishing Supplies  
___Contractor’s Supplies  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
___Combination Planer/Jointer  
___Other_________________________________  
5. How would you rank your woodworking skills?  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
12. What new accessories would you like Grizzly  
Industrial to carry?  
6. What stationary woodworking tools do you own?  
Check all that apply.  
___Builders Hardware  
___Fasteners  
___Hand Tools  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
___Wood Components  
___Other_________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
13. What other companies do you purchase your tools  
and supplies from?  
_________________________________________  
_________________________________________  
_________________________________________  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
14. Do you think your purchase represents good value?  
___Other______________________________  
___Yes  
___No  
7. How many of your woodworking machines are  
Grizzly? _____________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
8. Which benchtop tools do you own? Check all  
that apply.  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___Yes  
___No  
___8" Table Saw  
___Scroll Saw  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___Other______________________________  
-7-  
H0602 12V Cordless Vacuum  
 
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
 

Heat Glo LifeStyle Indoor Fireplace DAKOTA AU User Manual
Honeywell Humidifier 69 2286EFS 03 User Manual
Hoshizaki Ice Maker IM 51BAE User Manual
HP Hewlett Packard Hearing Aid RM500SL User Manual
HP Hewlett Packard Satellite Radio HP 4945A User Manual
Humminbird Laminator LCR4 ID User Manual
Hustler Turf Lawn Mower Z XR7 User Manual
IDEAL INDUSTRIES Thermometer 61 633 User Manual
iLive MP3 Docking Station IC609 User Manual
Impex Home Gym IGS 16 User Manual