Graco Water Pump 220575 User Manual

Instructions – Parts List  
55 GALLON SUPPLY PUMPS  
3:1 Presidentr, 4:1 Presidentr,  
307745G  
and 2:1 Monarkr  
With drum cover and agitator  
Model 220575, Series B  
with 3:1 Ratio President Pump  
500 psi (3.5 MPa, 35 bar) MAXIMUM FLUID WORKING PRESSURE  
Model 230992, Series C  
with 4:1 Ratio President Pump  
400 psi (2.8 MPa, 28 bar) MAXIMUM FLUID WORKING PRESSURE  
Model 230993, Series C  
with 2:1 Ratio Monark Pump  
200 psi (1.4 MPa, 14.0 bar) MAXIMUM FLUID WORKING PRESSURE  
Read warnings and instructions.  
See page 2 for table of contents.  
04281A  
Model 230992 Shown  
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441  
Copyright 1985, Graco Inc. is registered to I.S. EN ISO 9001  
 
WARNING  
MOVING PARTS HAZARD  
D The air motor piston can pinch or amputate your fingers.  
D The rotating blades of the agitator can pinch or amputate your fingers or other body parts and can  
cause splashing in the eyes or on the skin.  
D Always shut off the agitator and disconnect the air line before adjusting the angle of the agitator,  
removing the agitator from the drum, or checking or repairing any part of the agitator.  
D Keep clear of all moving parts when starting or operating the equipment.  
D Before servicing the equipment, follow the Pressure Relief Procedure on page 7 to prevent the  
equipment from starting unexpectedly.  
307745  
3
 
WARNING  
FIRE AND EXPLOSION HAZARD  
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and  
result in a fire or explosion and serious injury.  
D Ground the equipment and the object being sprayed. Refer to Grounding on page 5.  
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-  
ing immediately. Do not use the equipment until you identify and correct the problem.  
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid  
being sprayed.  
D Keep the spray area free of debris, including solvent, rags, and gasoline.  
D Electrically disconnect all equipment in the spray area.  
D Extinguish all open flames or pilot lights in the spray area.  
D Do not smoke in the spray area.  
D Do not turn on or off any light switches in the spray area while operating or if fumes are present.  
D Do not operate a gasoline engine in the spray area.  
TOXIC FLUID HAZARD  
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,  
inhaled, or swallowed.  
D Know the specific hazards of the fluid you are using.  
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,  
state and national guidelines.  
D Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and  
solvent manufacturer.  
4
307745  
 
Setup  
NOTES:  
Object being sprayed: Follow your local code.  
Fluid supply container: Follow your local code.  
Solvent pails used when flushing: Follow your local  
code. Use only metal pails, which are conductive,  
placed on a grounded surface. Do not place the pail  
on a nonconductive surface, such as paper or card-  
board, which interrupts the grounding continuity.  
To maintain proper grounding continuity when flushing  
or relieving pressure, always hold the metal part of the  
spray gun firmly to the side of a grounded metal pail,  
then trigger the gun.  
D Reference numbers and letters in parentheses in  
the text refer to the callouts in the figures and the  
parts drawing.  
D Accessories are available from your Graco repre-  
sentative. If you supply your own accessories, be  
sure they are adequately sized and pressure-rated  
to meet the system’s requirements.  
Grounding  
Positioning the Unit  
WARNING  
Select a convenient location for the unit. The air  
valves for the pump (37) and agitator (5) must be fully  
accessible.  
System Accessories  
FIRE AND EXPLOSION HAZARD  
Before operating the pump, ground the  
system as explained below. Also read  
the section FIRE AND EXPLOSION  
HAZARD on page 4.  
WARNING  
Proper grounding is an essential part of maintaining a  
safe system.  
A bleed-type master air valve (N) and a fluid drain  
valve (K) are required in your system. These  
accessories help reduce the risk of serious injury,  
including splashing of fluid in the eyes or on the  
skin, and injury from moving parts if you are adjust-  
ing or repairing the pump or agitator.  
The bleed-type master air valve relieves air  
trapped between this valve and the pump after the  
air is shut off. Trapped air can cause the pump to  
cycle unexpectedly. Locate the valve close to the  
pump. A red–handled bleed–type ball valve is  
supplied to relieve air trapped in the air motor.  
The fluid drain valve assists in relieving fluid pres-  
sure in the displacement pump, hose, and gun.  
Triggering the gun to relieve pressure may not be  
sufficient. Order Part No. 210071.  
To reduce the risk of static sparking, the mounting  
cover and all electrically conductive objects or devices  
in the spray area must be properly grounded. Check  
your local electrical code for detailed grounding  
instructions for your area and type of equipment.  
Agitator and drum cover: Connect one end of the  
ground wire (Y) to the ground connector (X) on the rim  
of the drum cover. See Fig. 1. Connect the other end  
of the ground wire to a true earth ground. See the  
pump instruction manual (307986 for 230992, 307985  
for model 230993, or 308793 for model 220575) for  
instructions on grounding the pump.  
X
Y
Fig. 1  
Air and fluid hoses: Use only electrically conductive  
hoses with 500 ft. (150 m) maximum combined hose  
length to ensure grounding continuity.  
Air compressor: Follow manufacturer’s recommenda-  
tions.  
Spray gun or dispensing valve: Ground through con-  
nection to a properly grounded fluid hose and pump.  
307745  
5
 
Setup  
The installation shown in Fig. 2 is only a guide for selecting and installing system components and accessories.  
Contact your Graco representative for assistance in designing a system to suit your particular needs.  
D The fluid line must include a fluid drain valve (K),  
Connecting the Unit and Accessories  
which helps relieve fluid pressure in the hose and  
D Ground the unit as described in Grounding on  
gun.  
page 5.  
D You should install an air line filter (J) to remove dirt  
D The main air supply must include a bleed-type  
master air valve (N) for shutting off air pressure to  
the unit (supplied with Model 230992).  
and moisture from the air supply.  
D Downstream from the air filter, you should install an  
air line lubricator (H) for automatic air motor lubrica-  
tion.  
D Connect a grounded air supply hose to the bleed  
type pump air valve (N).  
MAIN AIR SUPPLY LINE  
FLUID SUPPLY LINE  
F
E
G
J
203  
206a  
204 3  
201  
B
A
Y
C
D
K
H
N
206b  
SECONDARY FLUID RETURN  
M
L
MAIN FLUID RETURN  
KEY  
A
B
C
D
E
F
Air Filter/Regulator to Gun  
Fluid Pressure Regulator  
Fluid Shutoff Valve  
Fluid Filter  
Surge Tank  
Bleed–type Master Air Valve  
H
J
K
L
Air Line Lubricator  
Air Filter to Pump  
Drain Valve  
Air Spray Circulating Gun  
Back Pressure Valve  
Y
3
Drum Cover/Agitator Ground Wire  
Agitator  
201 Air Supply Hose  
203 Back Pressure Valve  
204 Air Regulator  
206a Return Fluid Hose  
206b Supply Fluid Hose  
M
(same as 203 except customer supplied)  
Bleed–type Pump Air Valve  
G
Pump Ground Wire  
N
04283A  
Fig. 2  
6
307745  
 
Operation  
Flush the pump before first use. The pump is  
Pressure Relief Procedure  
tested with lightweight oil, which is left in to protect the  
pump parts. If the fluid you are using may be contami-  
nated by the oil, flush it out with a compatible solvent.  
WARNING  
PRESSURIZED EQUIPMENT HAZARD  
The system pressure must be manually relieved to  
prevent the system from starting or spraying acci-  
dentally. To reduce the risk of an injury from acci-  
dental spray from the gun, splashing fluid, or  
moving parts, follow the Pressure Relief Proce-  
dure whenever you:  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure at left.  
D are instructed to relieve the pressure,  
D stop spraying,  
To clean any settled particles out of the system, flush  
the entire system at least once each 90 days or less. If  
possible, circulate the solvent and leave it in the lines  
for two days, such as over the weekend, to help loosen  
any dried paint.  
D check or service any of the system equipment,  
D or install or clean the spray nozzle.  
1. Relieve the pressure.  
1. Lock the gun trigger safety.  
2. Shutdown the system as explained in Shutdown  
and Care of the Pump on page 9.  
2. Shut off the air supply to the pump.  
3. Close the bleed-type master air valve (required in  
your system). On Model 230992, this is the red–  
handled ball valve, assembled next to the air  
regulator.  
3. Start the pump and operate it at about 30 cycles  
per minute.  
4. Lubricate the agitator, if you haven’t already done  
so, and then close its air valve to stop agitation.  
4. Unlock the gun trigger safety.  
5. Hold a metal part of the gun firmly to the side of a  
grounded metal pail, and trigger the gun to relieve  
pressure.  
WARNING  
Failure to shut off the agitator before raising the  
pump assembly may result in serious injury from  
splashing paint in the eyes or contact with the  
blades of the agitator.  
6. Lock the gun trigger safety.  
7. Open the drain valve (required in your system),  
and have a container ready to catch the drainage.  
8. Leave the drain valve open until you are ready to  
spray again.  
5. Raise the pump out of the paint while it is still  
running and let it run itself dry to force the paint  
back into the drum. Shut off the pump.  
If you suspect that the spray tip or hose is completely  
clogged, or that pressure has not been fully relieved  
after following the steps above, very slowly loosen the  
tip guard retaining nut or hose end coupling and relieve  
the pressure gradually. Then loosen it completely.  
Then clear the tip or hose.  
CAUTION  
Never leave water or water-based fluid in the pump  
overnight. Flush with a compatible solvent to protect  
the parts from corrosion.  
Flushing  
WARNING  
6. Remove the paint drum and place a 55 gallon  
drum, containing enough solvent to thoroughly fill  
and flush the system, under the pump. Lower the  
pump.  
FIRE AND EXPLOSION HAZARD  
Before flushing, read the section FIRE  
AND EXPLOSION HAZARD on page  
4. Be sure the entire system and  
flushing pails are properly grounded.  
Refer to Grounding on page 5.  
7. Start the pump again and allow the solvent to  
circulate for at least one hour.  
307745  
7
 
Operation  
8. Shut off the air to the pump, open the bleed–type  
5. When the paint returns through the return line in a  
steady stream, turn on the air to one gun, open  
both fluid shutoff valves (C) near the gun, and  
adjust the fluid regulator (B). See the manuals  
supplied with these components for pressure  
range and adjustment . Repeat for all gun stations.  
master air valve, and open the drain valve (K).  
Leave the solvent in the system overnight or, if  
possible, all weekend.  
9. Start the pump and circulate it again for 30 min-  
utes. Raise the pump out of the solvent and let it  
dry to force out the solvent. Drain solvent from all  
outlet loops and filters.  
6. Paint line pressure is controlled by the back pres-  
sure regulator (203). This regulator restricts flow of  
paint in the line so there is sufficient paint pressure  
at all gun stations. Turn the regulator handle  
clockwise to increase and counter–clockwise  
to decrease pressure.  
10. Place the paint supply drum under the pump,  
agitate the paint, install the gun and hoses.  
11. Reset the air and fluid pressure regulators to  
complete the system flushing.  
Adjust the regulator so there is about 10 psi  
(0.6 bar) more fluid pressure at the regulator  
than is required at the last gun in the line.  
Adjusting the Unit  
Install supply drum under cover/pump. Make sure that  
the cover is supported by the drum.  
NOTE: As you increase fluid line pressure, you must  
also increase air pressure to the pump, so the pump  
can handle the heavier load. However, never increase  
the pressure so much that you exceed the maximum  
working pressure of any component in the system.  
7. As you start to spray, adjust the air and fluid  
pressures to the gun to obtain the best results.  
CAUTION  
Shortened or recycled drums may cause the pump  
or agitator to bottom out in the drum, causing  
damage. Contact your fluid supplier to order a  
standard size drum.  
1. Unscrew the filter bowl and remove the filter  
screen. Replace the bowl. Flush the unit until  
clear solvent comes from the gun, then reinstall  
the filter screen.  
CAUTION  
Do not allow the pump to run dry. It will quickly  
accelerate to a high speed, causing damage. If  
your pump is running too fast, stop it immediately  
and check the fluid supply. If the container is  
empty and air has been pumped into the lines, refill  
the container and prime the pump and the lines, or  
flush and leave it filled with a compatible solvent.  
Eliminate all air from the fluid system.  
2. Before operation, ensure that all fasteners and  
tube connections are tightened securely.  
Starting and Adjusting the Pump  
1. Close the air regulator (204).  
2. Start the agitator (3). Agitate the paint just fast  
enough to keep all paint particles suspended.  
Over–agitating causes air bubbles in the paint  
which can cause poor gun performance and poor  
surface finish.  
WARNING  
COMPONENT RUPTURE HAZARD  
To reduce the risk of overpressurizing  
your system, which could cause compo-  
nent rupture and serious injury, never  
exceed the specified Maximum Incoming Air Pres-  
sure to the pump. (see Technical Data on  
page 15.)  
3. Open the red–handled ball valve. Open the pump’s  
bleed-type master air valve (N).  
4. Slowly open the air regulator until the pump starts.  
Adjust it until the pump cycles slowly – about 50  
cycles per minute.  
8
307745  
 
Operation  
4. Open the bleed–type master air valve (N), and the  
Shutdown and Care of the Pump  
pump air regulator (204) to restart the pump.  
Circulate the paint to remove all trapped air before  
shutting down.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 7.  
5. Disconnect the gun’s fluid hose from the gun and  
the fluid regulator. Plug the regulator outlet. Blow  
compressed air and compatible solvent through  
the hose to clean it. Clean the gun according to the  
instructions supplied with it. Each month remove  
and clean the fluid regulator.  
Never allow paint to dry in the pump and lines.  
To shutdown the system  
1. Relieve the pressure. Stop the agitator, and  
lubricate it.  
6. If you are not using an air line lubricator, manually  
lubricate the motor at least once a day.  
2. If using a Graco fluid pressure regulator at the  
gun, reverse its regulating key and thread it into  
the regulator cap as far as it will go.  
7. Circulate the fluid in the lines often enough during  
the shutdown to prevent the paint from drying.  
3. Loosen the spray gun air cap about three turns,  
hold a rag over the front of the air cap and fully  
trigger the gun. This forces paint in the gun, hose  
and regulator back into the circulating line. Close  
the fluid shutoff valves (C) at that gun station,  
Repeat for the other gun stations.  
NOTE: To drain the circulating lines and flush the  
system, see Flushing on page 7.  
307745  
9
 
Parts Drawing  
Model 230992, Series B  
4:1 Ratio President Carbon Steel  
55 Gallon Drum System  
Model 230993, Series B  
2:1 Ratio Monark Carbon Steel  
55 Gallon Drum System  
Includes items 1 to 4, and 6 to 12  
Includes items 2 to 6, and 11  
6
1 or 5  
(MONARK PUMP SHOWN)  
8
9
10  
11  
12  
2
7
3
c
Fig. 3  
10  
307745  
 
 
Parts List  
Model 230992, Series B  
4:1 Ratio President Carbon Steel  
55 Gallon Drum System  
Includes items 1 to 4, and 6 to 12  
Model 230993, Series B  
2:1 Ratio Monark Carbon Steel  
55 Gallon Drum System  
Includes items 2 to 6, and 11  
Ref.  
Ref.  
No.  
No.  
Part No. Description  
Qty.  
Part No. Description  
Qty.  
1
223183  
237307  
203711  
223185  
237569  
4:1 RATIO PRESIDENT PUMP;  
See 307986 for parts.  
COVER, drum;  
See 308466 for parts.  
AGITATOR;  
See 306459 for parts.  
2:1 RATIO MONARK PUMP;  
See 307985 for parts  
GROUND WIRE AND CLAMP  
1
1
1
7
8
9
10  
160032  
158491  
113331  
156684  
NIPPLE; 3/4 npt x 2  
NIPPLE; 1/2 npt x 2  
BALL VALVE, air, bleed-type  
UNION, adapter, swivel; 1/2” npt(m)  
1
1
1
2
3
5
6
x 1/2 npt(f)  
1
11  
12  
158491  
159239  
162505  
FITTING, nipple(used on 230992) 1  
FITTING, nipple(used on 230993) 1  
1
1
UNION, swivel  
1
307745 11  
 
Parts Drawing  
Model 220575, Series B  
3:1 Ratio President Stainless Steel  
55 Gallon Drum System  
Includes items 1–35  
Remove and discard 1/2 x 3/8 npt nipple from outlet of  
1
air regulator (5a), and replace with 1/2 npt nipple (5c). Then  
connect air regulator assy to pump air inlet.  
Agitator (3) is tilted at a 6_ angle.  
2
1
1
Ref No. 5 includes  
4
items 5a–5c.  
5a  
5c  
35  
3 REF  
1 REF  
22  
23  
6d  
2
17  
6b,6c  
20  
3 REF  
Ref No. 6 includes  
items 6a–6d.  
6a  
19  
18  
3
2
7679A  
12  
307745  
 
Parts List  
Model 220575, Series B  
3:1 Ratio President Stainless Steel  
55 Gallon Drum System  
6
223319  
RETURN TUBE KIT  
Includes items 6a–6d  
Ref  
No.  
Part  
No.  
1
Description  
Qty  
Ref  
No.  
Part  
No.  
Description  
Qty  
1
220564  
237309  
222698  
220580  
223180  
203716  
205418  
158491  
PUMP, President  
See 308793 for parts  
COVER, drum, 55 gal. (200 liter)  
See 308466 for parts  
AGITATOR  
See 306840 for parts  
RISER TUBE KIT  
See 307837 for parts  
AIR REGULATOR KIT  
Includes items 5a–5c  
REGULATOR, air  
See 308167 for parts  
HOSE, air; buna-N; 1/2” ID;  
coupled 1/2 npt (mbe); 6 ft (1.9 m) lg  
NIPPLE; 1/2 npt  
1
1
1
1
1
1
6a  
6b  
6c  
185393  
178941  
185394  
TUBE, return; sst; 1” npt(m)  
NUT, hex; 1–5/8–18 unef–2b  
ADAPTER, return;  
1–5/8–18 unef–2a(m) x  
1” npt(f) x 1” npt(f)  
ELBOW, street; 1” npt (m x f)  
NIPPLE, half; 1–1/2” npt  
GASKET, agitator, guide  
SCREW, cap, hex hd  
WASHER, lock, spring  
PLATE, adapter  
SCREW, cap, hex hd  
WASHER, lock, 5/16 in.  
ELBOW, 1/8 npt (m x f)  
1
1
2
3
1
1
1
1
4
4
1
3
3
1
4
6d  
7
108761  
185466  
190192  
112896  
104123  
174092  
112894  
112904  
100839  
5
17  
18  
19  
20  
22  
23  
35  
5a  
5b  
5c  
1
1
307745 13  
 
Notes  
14  
307745  
 
Technical Data  
Category  
Model 220575  
Model 230992  
Model 230993  
Ratio  
3:1  
4:1  
2:1  
Maximum fluid working  
pressure  
500 psi (3.5 MPa, 35 bar)  
400 psi (2.8 MPa, 28 bar) 200 psi (1.4 MPa, 14 bar)  
Maximum air input  
pressure  
166 psi (1.2 MPa, 11.6  
bar)  
100 psi (0.7 MPa, 7 bar)  
100 psi (0.7 MPa, 7 bar)  
11  
Pump cycles per 1 gallon  
(3.8 liters)  
6.3  
8
Fluid flow at 60 cycles per 9.2 gpm (35.1 liters/min)  
minute  
8 gpm (30.4 liters/min)  
5.5 gpm (21 liters/min)  
Fluid inlet size  
Fluid outlet size  
Air inlet size  
Weight  
1–1/2 npt(f)  
1 in. npt(f)  
1/2 npt(f)  
1–1/2 npt(f)  
1 in. npt(f)  
1–1/2 npt(f)  
1 in. npt(f)  
3/8 npt(f)  
3/8 npsm(f)  
110 lb (50 kg)  
180_F (82_C)  
110 lb (50 kg)  
110 lb (50 kg)  
180_F (82_C)  
Maximum pump operating 180_F (82_C)  
temperature  
* Sound pressure levels  
(dBa) (Input air pressures (0.3 MPa, 2.8 bar)  
at 15 cycles per minute)  
73.6 dB(A) @ 40psi  
73.6 dB(A) @ 40 psi  
(0.3 MPa, 2.8 bar)  
78.3 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
80.9 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
73.3 dB(A) @ 40 psi  
(0.3 MPa, 2.8 bar)  
75.9 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
77.7 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
78.3 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
80.9 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
* Sound power levels  
(dBa) (Input air pressures (0.3 MPa, 2.8 bar)  
at 15 cycles per minute)  
87.4 dB(A) @ 40 psi  
87.4 dB(A) @ 40 psi  
(0.3 MPa, 2.8 bar)  
92.1 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
94.6 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
87.0 dB(A) @ 40 psi  
(0.28 MPa, 2.8 bar)  
89.7 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
91.4 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
92.1 dB(A) @ 70 psi  
(0.5 MPa, 4.8 bar)  
94.6 dB(A) @100 psi  
(0.7 MPa, 7 bar)  
Wetted parts  
Chrome Plated Stainless  
Steel, Ultra–High  
Molecular Weight  
Polyethylene, Leather,  
PTFE  
Supply and Return Tubes: Nickel-plated carbon steel  
Air Motor Base: Aluminum  
Displacement Pump: Refer to manual 307983  
* Tested in accordance with ISO 9614–2.  
307745 15  
 
Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,  
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be  
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-  
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of  
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-  
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires  
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers  
to identify the distributor closest to you:  
1–800–328–0211 Toll Free  
612–623–6921  
612–378–3505 Fax  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Sales Office: Minneapolis  
International Offices: Belgium, Korea, Hong Kong, Japan  
PRINTED IN USA 307745 05/1986, Revised 04/2004  
16  
307745  
 

Haier Paint Sprayer DW12 CBE6 User Manual
Hamilton Beach Iron 840091300 User Manual
Hans Grohe Indoor Furnishings 10020XX1 User Manual
Harbor Freight Tools Air Compressor 47407 User Manual
Hasbro Games Dr Busby User Manual
Honeywell Ventilation Hood ER150C User Manual
Hotpoint Washer Dryer HF8B User Manual
HP Hewlett Packard Power Supply HP T1000 G3 User Manual
IBM Computer Monitor 31P6240 User Manual
Imation Computer Drive RDX User Manual