OPERATION –
UTILIZAÇÃO –
FONCTIONNEMENT –
FUNCIONAMIENTO
309402
Rev. C
Line Drivert
Model 233725
10 mph (16 kph) Maximum Operating Speed / de vitesse de fonctionnement maximum / de
velocidade operando se máxima / de la velocidad de funcionamiento máxima
Related manuals
Manuais associados
Manuels afférents
Manuales relacionados
All models not available in all countries.
Nem todos os modelos existem à disposição em todos os países.
Tous les modèles ne sont pas disponibles dans tous les pays.
Hay modelos que no se distribuyen en todos los países.
How To Perform:
S Component Identification . . . . . . . . . . . . . . . . 4
S Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
S Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
S Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 2001, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
WARNING
MOVING VEHICLE HAZARD
MOVING VEHICLE HAZARD
Careless and reckless behavior causes
accidents. Falling from vehicle, running into
people or objects, or being struck by other
vehicles may result in serious injury or
death.
Careless and reckless behavior causes
accidents. Falling from vehicle, running into
people or objects, or being struck by other
vehicles may result in serious injury or
death.
D
Use appropriate traffic control in all traffic
areas
D
Use appropriate traffic control in all traffic
areas
D
D
D
D
D
D
Do not step on forward/reverse pedals
Make turns slowly
D
D
D
D
D
D
Do not step on forward/reverse pedals
Make turns slowly
Do not carry passengers
Do not carry passengers
Do not operate on slopes greater than 15_
Loss of traction may occur going downhill
Do not operate on slopes greater than 15_
Loss of traction may occur going downhill
Reference Manual on Uniform Traffic
Control Devices (MUTCD), U.S. Depart-
ment of Transportation, Federal Highway
Administration or local highway and trans-
portation regulations for proper traffic
control.
Reference Manual on Uniform Traffic
Control Devices (MUTCD), U.S. Depart-
ment of Transportation, Federal Highway
Administration or local highway and trans-
portation regulations for proper traffic
control.
D
D
D
Do not make turns greater than 45_
Do not tow
D
D
D
Do not make turns greater than 45_
Do not tow
Use with line striping equipment only
Use with line striping equipment only
FIRE AND EXPLOSION HAZARD
Fuel spilled on a hot surface can
cause a fire or explosion and serious
bodily injury or death. Shut off engine
and let engine cool before filling tank.
FIRE AND EXPLOSION HAZARD
Fuel spilled on a hot surface can
cause a fire or explosion and serious
bodily injury or death. Shut off engine
and let engine cool before filling tank.
HOT SURFACE HAZARD
Engine and drive housing may be very
hot during operation and could burn skin
if touched.
HOT SURFACE HAZARD
Engine and drive housing may be very
hot during operation and could burn skin
if touched.
TOXIC FUMES HAZARD
TOXIC FUMES HAZARD
Engine produces carbon monoxide which is a
deadly gas. Do not operate in an enclosed
area. Breathing carbon monoxide may result
in serious injury or death.
Engine produces carbon monoxide which is a
deadly gas. Do not operate in an enclosed
area. Breathing carbon monoxide may result
in serious injury or death.
309402
3
Component Identification
T
L
S
A
K
J
M
R
B
P
N
C
D
Adjust coupler pressure
on 1–7/8 in. receiver ball
before use
H
E
F
G
A
B
C
D
E
Wheel Release
Engine
Engine ON/OFF
Light
Tires: inflate to equal and
Rated Pressure
F
G
H
J
Direction/Speed Pedals
Step Plate
Coupler
Hitch
K
L
Safety Pin Location
Handle Open
Handle Locked
Parking Brake
Storage
M
N
P
R
S
T
Seat Adjustment
Operator Seat
Hydraulic Fill Cap
4
309402
Setup
Unpack Line Driver
1. Remove Line Driver from packing.
2. Disengage drive wheels. This makes
it easier to roll the Line Driver.
Release
Engage
3. Hand tighten after use.
Connect Hitch Receiver to Line Striper – Hitch Receiver Kit 245321 Manual 309405
Connect Line Driver to Line Striper
1. Install Line Driver hitch coupler to LineLazer hitch receiver ball.
(M)
2. Latch coupler to locked position (M)
3. Insert safety pin in latch
309402
5
Setup
Individual Operator Adjustments
Seat
Adjust seat forward/backward with lever (R) below seat
Pedals
Suggestion: Adjust one pedal for full motion forward
and one for full motion in reverse. This reduces fatigue.
1. Loosen two bolts (C) at
underside of pedals
Example:
Reverse
Forward
2. Rotate pedal to desired position
3. Tighten bolts.
C
Striper Handle
Bars
Refer to your striper manual
6
309402
Startup
1. Check engine oil level. Add SAE 10W–30
(summer) or 5W–20 (winter), if necessary.
Note: Keep engine oil at full level to avoid
nuisance stalls because Oil Alert may sense
low oil levels during change of direction of
Line Driver
(cold)
2. Fill fuel tank.
3. Check hydraulic oil level. Add only Mobil 1 (15W–50)
synthetic oil. Hydraulic system capacity is 2 quarts.
Fill to baffle top
309402
7
Startup
4. Start engine
a. Engage parking brake
b. Move fuel valve to open
c. Move choke to closed
d. Set throttle to fast
a.
b.
d.
e. Set engine switch ON
f. Pull starter cord
c.
g. After engine starts, move
choke to open
h. Set throttle to desired speed for
striping.
e.
g.
f.
h.
8
309402
Operation
Note: Line Driver motion is forward
and reverse. Turns are made with the
striper.
1. Squeeze hand control and
release caster wheel.
2. Push striper handle bars to
begin desired turn.
309402
9
Operation
Note: Line Driver stops when both
feet are removed from pedals
1. Move pedal(s) forward to
drive Line Driver forward
2. Move pedal(s) reverse to
drive Line Driver reverse
3. Switching from forward to re-
verse creates a braking action
Reverse
Forward
4. Set parking brake when not
operating Line Driver
Note: The Line Driver can not be
started if the parking brake is not set.
The operator must be seated when
the parking brake is released or the
Line Driver will stop running.
RELEASE
ENGAGE
10
309402
Troubleshooting
PROBLEM
CAUSE
SOLUTION
Engine does not start
Parking brake not engaged. Engine
switch OFF, no gasoline or low oil
Set Brake. Consult engine manual, supplied
Engine races to high rpm – stalls
during operation
Worn governor
Consult engine manual, supplied
Engine operates, Line Driver does
not move forward or reverse
Low hydraulic oil
Fill with Mobil 1 (15W–50) synthetic oil
Engine operates, Line Driver moves Low hydraulic oil. Parking brake is set Fill with Mobil 1 (15W–50) synthetic oil. Release
slowly in forward and reverse
parking brake.
Wheel release is open.
Safety switch
Close; hand tight.
Engine shuts off when operator ex-
its Line Driver
Set parking brake
Engine continues to run when oper- Safety switch
ator exits Line Driver and parking
brake is not set
Adjust and set parking brake. Replace safety
switch and/or any connecting wires.
Engine misses during turns and for- Engine oil low
ward and reverse changes
Consult engine manual for proper oil
Adjust brake. Manual 309404.
Parking brake does not keep Line
Driver from moving
Parking brake needs adjustment
Line Driver creeps in forward or re-
verse direction
Control linkage needs adjustment
Adjust control linkage. Manual 309404.
309402
11
Graco Warranty
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special extended or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in
accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–690–2894 Toll Free.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
mm 309402
This manaul contains English, Portuguese, French, Spanish
Graco Headquarters: Minneapolis
International Offices: Belgium, Korea, China, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
10/2001, Revised 8/2006
12
309402
|