gogo Kidz™ Travelmate
Operating &
Safety Manual
Model # NMJ2
Model # GGK2
Go-Go Babyz Corporation
7011 Realm Drive, Suite A5
San Jose, CA 95119
phone: 1.888.686.2552
Fax: 1.408.360.7967
Email: [email protected]
Web: www.gogobabyz.com
Go-Go Babyz Corporation
never leave child alone with the gogo
kidz assembled onto the car seat. unit
may rotate backwards and create injury
to your child.
!
!
WARNING
WARNING
CARE AND MAINTENANCE
Before connecting the gogo Kidz™ to your Britax® car seat, make sure the
unit is assembled correctly and all parts and fasteners are secure.
Excessive weight, parcels, or accessory
items placed or hung on the handle may
cause the unit to become unstable.
After assembly pull horizontally on the back of the gogo Kidz to
make certain the guides are aligned properly and there is no slippage.
- Do not place parcels or accessory items on the handle.
- Do not allow children to play with or hang onto the stroller.
Confirm that knobs are tight and there is no space between the gogo Kidz
plate and the car seat.
Do not allow children to climb into or
out of the car seat while gogo Kidz is
secured.
!
WARNING
Periodically check for worn parts and loose screws. Also, check that the
handle, axle and wheels are secure.
Never use stroller on stairways or
WARNING escalators.
!
Replace any damaged parts immediately.
Clean with a damp cloth and wipe dry.
Always ensure knobs are tight when-
ever the gogo Kidz is attached to
the car seat
!
WARNING
Do not store unit outside exposed to rain or extreme sunlight.
Do not place heavy items on top of unit when storing it.
- Injury to your child could result if the unit where to come off accidentally
when traveling with your child.
The stroller is designed to roll.
!
WARNING
WARNING
Do not leave the gogo Kidz attached
to the Britax car seat while driving
in an automobile. The gogo Kidz has
not been tested in combination with
the Britax seats in any crash testing
program and injury to your child
could occur.
!
How to properly
Assemble your gogo Kidz™ Travelmate
For the Roundabout®, Marathon™ & Decathlon™
Special Instructions for transporting
your child in the gogo Kidz™ Travelmate
Step 1. Lay seat face down and insert retainer bar in between seat-belt
holder of car seat.
The gogo Kidz needs no special instructions when transporting the Britax®
seat from place to place. However, when transporting a child over 35 lbs.,
strapped in the seat, follow these instructions:
Step 1. Attach the gogo Kidz to the Britax car seat by following the assembly
instructions. After the gogo Kidz is attached to the Britax seat, and the
handle is in the collapsed position, pull 10 inches of the “versa-tether”
strap from the pouch that is located on the rear of the seat near the top.
Tether Pouch
Step 2. Align the bottom tabs with the bottom of the car seat and lay the
gogo Kidz plate on the back of the car seat.
Step 2. Pull the strap over the handle and tighten the “versa-tether” by
pulling on the end of the tether strap. Place excess strap back into the pouch.
Tuck in all remaining latch and tether straps in order not to get tangled when
in use.
Step 3. Insert the screws into the holes on the back of the plate and tighten.
You may need to pull up on the bar while screwing.
Step 3. Always secure your child with the safety harness provided by the car
seat manufacturer.
Special Instructions for Inserting the Retainer
Bar with the Wizard® or Boulevard™ car seat
Please follow the instructions above for complete assembly.
To attach the Wizard/Boulevard Retainer Bar,
roll the cut out portion around the bar in the
back of the seat, starting from the bottom with
the cut out prtion facing the top of the seat.
The two conical sections should be facing
towards you at this point. Use the fingers of
one hand to align the conical shapes with the
holes int he main plate and thred the Thumb-
screws with the other hand.
|