Gateway Computer Monitor VX760 User Manual

USER GUIDE  
Gateway VX760/VX765 Monitor  
 
Contents  
Using Your VX760/VX765 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
Setting up the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Adjusting settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
On-screen display menu options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Maintaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Safety, Regulatory, and Legal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
i
 
Contents  
ii  
 
Using Your VX760/VX765 Monitor  
• Setting up the monitor  
• Adjusting settings  
• Maintaining  
• Troubleshooting  
• Specifications  
1
 
 
Using Your VX760/VX765 Monitor  
Setting up the monitor  
Read all instructions before using the monitor and save them for later use.  
Follow all warnings and instructions marked on the product.  
To set up the monitor:  
Attach the base  
Connect the video and power cables  
To attach the base:  
1 Carefully set the monitor on its side.  
2 Hold the base with the tab facing the back of the monitor and align the  
hooks on the base with the corresponding slots on the bottom of the  
monitor.  
3 Slide the base toward the front of the monitor so all hooks are securely in  
place. A retaining latch built into the base clicks into place when the base  
is correctly attached.  
4 Carefully set the monitor upright and place it on a sturdy, level surface.  
To connect the video and power cables:  
1 Position the monitor and your computer so you can easily get at the back  
panel of each. Make sure that all power cables can reach a correctly  
grounded electrical outlet.  
2 Connect the video cable to the matching (blue) video port on the back of  
your computer.  
3 Tighten the screws on the video cable connector to keep it from coming  
loose. Tightening the screws also prevents radio and TV interference.  
2
 
 
Setting up the monitor  
Caution  
4 Connect the power cable that came with the monitor to the AC power  
connector on the back of the monitor. Only use the power cable that came  
with the monitor.  
The openings in the monitor cabinet are  
for ventilation. Do not block or cover  
these openings. Do not insert anything  
into these openings. If you put the  
monitor in a bookcase or some other  
enclosed space, make sure to leave at  
least six inches (15 cm) around it for  
ventilation.  
AC power  
connector  
5 Plug the other end of the power cable into a correctly grounded electrical  
outlet.  
To turn on the monitor:  
1 Press the power button on the front of the monitor.  
EXIT button  
MENU button  
Power button  
Brightness/ button  
Contrast/ button  
2 Turn on your computer.  
3
 
Using Your VX760/VX765 Monitor  
Adjusting settings  
Power button. Turns the monitor on and off.  
Power indicator. Turns blue when the monitor is operating normally, then  
flashes when the monitor is in energy saving mode.  
MENU button. Enters the on-screen display (OSD) menu or selects an OSD  
menu option.  
Brightness/ button. OSD inactive: Adjusts the brightness.  
OSD active: Navigates to and adjusts the OSD menu options.  
Contrast/ button. OSD inactive: Adjusts the contrast.  
OSD active: Navigates to and adjusts the selected OSD menu option.  
Exit. Exits the OSD menu or sub-menu.  
To adjust monitor settings:  
1 Press the MENU button. The OSD menu opens.  
2 Press the  
or  
buttons to highlight an OSD menu option, then press  
the MENU button to select the option.  
3 Press the or buttons to adjust an OSD menu option.  
4 Press the EXIT button to save changes. Press the  
or  
buttons to  
highlight a different OSD menu option.  
- OR-  
If you have finished making all adjustments, press the EXIT button twice  
to save your settings and exit the OSD.  
4
 
 
Adjusting settings  
On-screen display menu options  
Icon  
Description  
CONTRAST. Adjusts the level of white between the lightest and darkest portions of an  
image.  
BRIGHTNESS. Adjusts the amount of light in the darkest portion of the picture.  
H. POSITION. Controls the horizontal position of the display image.  
H. SIZE. Controls the horizontal size of the display image.  
V. POSITION. Controls the vertical position of the display image.  
V. SIZE. Controls the vertical size of the display image.  
ROTATION. Rotates the display image.  
PINCUSHION. Curves the sides of the display image inward or outward.  
TRAPEZOID. Increases or decreases the trapezoid distortion of the display image.  
PARALLELOGRAM. Slants the display image to the left or right.  
PIN BALANCE. Curves the display image to the left or right.  
ADVANCED SELECT. Opens a submenu that contains menu options to adjust the top  
and bottom corners of the display and horizontal and vertical moire.  
MORE  
COLOR. Adjusts color balance. Select from two preset factory options (9300°K and  
6500°K) or USER. USER lets you adjust the red, green, and blue colors separately.  
OSD ADJUSTMENT. Opens a submenu that contains menu options that let you change  
the position of the OSD menu on the screen and the length of time the OSD menu is  
visible.  
OSD  
RESET. Resets the monitor settings to the factory default settings.  
LANGUAGE. Changes the display language for the OSD.  
EXIT. Displays current settings and exits the OSD menu.  
DEGAUSS. Demagnetizes the screen.  
R
EXIT  
5
 
 
Using Your VX760/VX765 Monitor  
Video modes  
The monitor supports several video modes from 720 × 400 to 1280 × 1024. The  
recommended video mode is 800 × 600 @ 85 Hz. Factory preset video modes  
include:  
Mode  
Resolution  
720 × 400  
640 × 480  
640 × 480  
800 × 600  
800 × 600  
800 × 600  
800 × 600  
1024 × 768  
1024 × 768  
1024 × 768  
1280 × 1024  
HF  
VF  
70  
60  
85  
75  
60  
85  
100  
60  
75  
85  
75  
1
31.47  
31.47  
43.27  
46.87  
37.88  
53.67  
63.90  
48.36  
60.02  
68.67  
60.30  
2
3
4
5
6
7
8
9
10  
11  
HF - Horizontal frequency (KHz)  
VF - Vertical frequency (Hz)  
Maintaining  
To keep the monitor in optimal working order:  
Do not block the ventilation holes.  
Do not expose the monitor to rain or use near water.  
Keep the monitor away from radiators or heat vents.  
Keep the monitor out of direct sunlight.  
Keep the monitor away from any equipment that generates a magnetic  
field.  
Use a screen saver to avoid permanent image burn-in. For more information  
about screen savers, see the documentation that came with your computer.  
Cleaning  
Warning  
Clean the monitor using a soft cloth lightly moistened with water. Wipe the  
cabinet, glass panel, and controls.  
When the monitor is turned off, a small  
amount of electrical current still flows  
through the monitor. To avoid electrical  
shock, always unplug all power cables  
and modem cables from the wall outlets  
before cleaning the system.  
Do not use any type of abrasive pad or glass cleaner. You will permanently  
scratch the glass panel.  
6
 
     
Troubleshooting  
Troubleshooting  
No picture  
Make sure that the monitor is turned on.  
Make sure that the power cord is connected correctly to both the back of  
the monitor and the wall outlet.  
Make sure that the video cable is connected securely to the back of your  
computer.  
If the power indicator is blinking:  
Make sure that your computer is turned on.  
Move the mouse or press any key on the keyboard to bring the  
monitor out of energy saving mode.  
Restart your computer with the monitor turned on.  
Make sure that the video cable is not damaged.  
Check the end of the video cable for any pins that might be bent or pushed  
in.  
Picture is scrambled  
If the picture is scrambled or does not look right, use the Reset option in the  
OSD to return the monitor to its factory default settings.  
Display colors are wrong  
Restart your computer with the monitor turned on.  
Make sure that the video cable is connected securely to the back of your  
computer.  
Make sure that the video cable is not damaged.  
Check the end of the video cable for any pins that might be bent or pushed  
in.  
Picture is fuzzy  
Adjust the contrast and brightness controls to improve the display image.  
Picture bounces, jitters, or has waves  
Make sure that:  
Non-shielded speakers are not placed too close to the monitor.  
The monitor is not positioned too close to another monitor, power  
transformer or adapter, electric fan, fluorescent light, metal shelf, or laser  
printer.  
If none of these suggestions solves the problem, try plugging the monitor into  
another outlet, preferably one on a different circuit.  
7
 
 
Using Your VX760/VX765 Monitor  
Picture has shadows or “ghosts”  
Remove any extension cables or switchboxes.  
Make sure that the video cable is connected securely to the back of your  
computer.  
Make sure that the video cable is not damaged.  
Check the end of the video cable for any pins that might be bent or pushed  
in.  
Color is not uniform  
Make sure that:  
The monitor warms up for at least 30 minutes before making a final  
judgment about color uniformity.  
Non-shielded speakers are not placed too close to the monitor.  
The monitor is not positioned too close to another monitor, power  
transformer or adapter, electric fan, fluorescent light, metal shelf, or laser  
printer.  
You demagnetize the screen using the Degauss option in the OSD.  
Image is not sized or centered correctly  
Use the size and position controls in the OSD to adjust the image.  
Image cannot be adjusted full screen  
Some video modes used by the monitor produce images that cannot be  
adjusted all the way out to the bezel edge (the edge where the screen glass and  
monitor casing meet).  
This condition does not indicate that the monitor is defective.  
8
 
Specifications  
Specifications  
Specifications are subject to change without obligation or notification.  
Flat 17-inch diagonal (16.0 inches viewable),  
anti-reflective/anti-glare, 90° deflection, 0.25 mm dot pitch  
CRT  
Horizontal frequency: 30-70 KHz  
Vertical frequency: 50-160 Hz  
Synchronization range  
Resolution  
Maximum: 1280 × 1024 @ 60 Hz  
Recommended: 800 × 600 @ 85 Hz  
110 MHz  
Dot rate  
Input voltage: AC 100-240 V @ 50/60 Hz  
Max power consumption: 68W (at 1152 × 864 resolution)  
Power supply  
Video: Analog 0.7 Vp-p/75 Ohms  
Sync: Separate sync, TTL level  
Input signal  
Unlimited colors  
Display analog input  
Weight  
Net: 40.7 lbs (18.5 kg)  
Gross: 46.2 lbs (21.0 kg)  
15.98 × 16.02 × 16.42 inches  
(406 × 407 × 417 mm)  
Dimensions (W×H×D)  
Operating conditions  
Storage conditions  
Temperature: 41°F to 104°F (5°C to 40°C)  
Humidity: 20% ~ 80%  
Temperature: -4°F to 140°F (-20°C to 60°C)  
Humidity: 10% ~ 90%  
9
 
 
Using Your VX760/VX765 Monitor  
10  
 
Safety, Regulatory, and Legal Information  
• Important safety information  
• Environmental information  
• Regulatory compliance statements  
• Notices  
11  
 
 
Important safety information  
Important safety information  
Warning  
Always follow these instructions to help  
guard against personal injury and  
damage to your Gateway product.  
Your Gateway product is designed and tested to meet the latest standards for safety of information technology equipment. However, to  
ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed.  
Setting up your system  
Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and  
operating instructions for future use.  
Do not use this product near water or a heat source such as a radiator.  
Set up the system on a stable work surface.  
The product should only be operated from the type of power source indicated on the rating label.  
If your product has a voltage selector switch, make sure that the switch is in the proper position for your area. The voltage selector switch  
is set at the factory to the correct voltage.  
Openings in the monitor case are provided for ventilation. Do not block or cover these openings. Make sure you provide adequate space,  
at least 6 inches (15 cm), around the system for ventilation when you set up your work area. Never insert objects of any kind into the  
monitor ventilation openings.  
Some products are equipped with a three-wire power cord to make sure that the product is properly grounded when in use. The plug on  
this cord will only fit into a grounding-type outlet. This is a safety feature. If you are unable to insert the plug into an outlet, contact an  
electrician to install the appropriate outlet.  
If you use an extension cord with this system, make sure that the total ampere rating on the products plugged into the extension cord  
does not exceed the extension cord ampere rating.  
If your system is fitted with a TV Tuner, cable, or satellite receiver card, make sure that the antenna or cable system is electrically  
grounded to provide some protection against voltage surges and buildup of static charges.  
Care during use  
Warning  
To prevent electric shock, never remove  
the cover. No user serviceable parts  
inside. Refer servicing to qualified service  
personnel.  
Do not walk on the power cord or allow anything to rest on it.  
Do not spill anything on the system. The best way to avoid spills is to avoid eating and drinking near your system.  
Do not expose the monitor to rain or use near water. If the monitor does get exposed to moisture, unplug it and allow it to dry for  
24 hours. Call Gateway Customer Care for advice on whether the monitor is safe to turn back on.  
When the monitor is turned off, a small amount of electrical current still flows through the monitor. To avoid electrical shock, always  
unplug all power cables and modem cables from the wall outlets before cleaning the system.  
Unplug the system from the wall outlet and refer servicing to qualified personnel if:  
The power cord or plug is damaged.  
Liquid has been spilled into the system.  
The system does not operate properly when the operating instructions are followed.  
The system was dropped or the cabinet is damaged.  
The system performance changes.  
Replacement parts and accessories  
Warning  
Do not use Gateway products in areas  
classified as hazardous locations. Such  
areas include patient care areas of  
medical and dental facilities,  
Use only replacement parts and accessories recommended by Gateway.  
oxygen-laden environments, or  
industrial facilities.  
12  
 
 
Environmental information  
Environmental information  
The product you have purchased contains extracted natural resources that have been used in the manufacturing process. This product may  
contain substances known to be hazardous to the environment or to human health.  
To prevent releases of harmful substances into the environment and to maximize the use of our natural resources, Gateway provides the  
following information on how you can responsibly recycle or reuse most of the materials in your “end of life” product.  
Waste Electrical and Electronic Equipment (commonly known as WEEE) should never be disposed of in the municipal waste  
stream (residential garbage collection). The “Crossed-Out Waste Bin” label affixed to this product is your reminder to dispose  
of your “end of life” product properly.  
Substances such as glass, plastics, and certain chemical compounds are highly recoverable, recyclable, and reusable. You can  
do your part for the environment by following these simple steps:  
When your electrical or electronic equipment is no longer useful to you, “take it back” to your local or regional waste collection  
administration for recycling.  
In some cases, your “end of life” product may be “traded in” for credit towards the purchase of new Gateway equipment. Call Gateway to  
see if this program is available in your area.  
If you need further assistance in recycling, reusing, or trading in your “end of life” product, you may contact us at the Customer Care  
number listed in your product’s user guide and we will be glad to help you with your effort.  
Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this  
product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by  
disposing of or recycling used batteries properly.  
With your help, we can reduce the amount of natural resources needed to produce electrical and electronic equipment, minimize the use of  
landfills for the disposal of “end of life” products, and generally improve our quality of life by ensuring that potentially hazardous  
substances are not released into the environment and are disposed of properly.  
13  
 
 
Regulatory compliance statements  
Regulatory compliance statements  
United States of America  
Federal Communications Commission (FCC) Unintentional emitter per FCC Part 15  
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits  
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  
radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment and receiver  
Connect the equipment to an outlet on a different circuit from that to which the receiver is connected  
Consult the dealer or an experienced radio/TV technician for help.  
Compliance Accessories: The accessories associated with this equipment are: shielded video cable. These accessories are required to be  
used in order to ensure compliance with FCC rules.  
FCC declaration of conformity  
Caution  
Changes or modifications not expressly  
approved by Gateway could void the FCC  
compliance and negate your authority to  
operate the product.  
Responsible party:  
Gateway, Inc.  
7565 Irvine Center Drive  
Irvine, CA 92618 USA  
This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) this device may  
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired  
operation.  
California  
Proposition 65 Warning  
This product contains chemicals,  
including lead, known to the State of  
California to cause cancer, birth defects  
or reproductive harm.  
Canada  
Industry Canada (IC) Unintentional emitter per ICES-003  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference  
regulations of Industry Canada.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B  
prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.  
14  
 
 
Notices  
Notices  
© 2005 Gateway, Inc.  
All rights reserved.  
Gateway, Inc.  
7565 Irvine Center Drive  
Irvine, CA 92618 USA  
All Rights Reserved  
This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any  
form, without prior consent in writing from Gateway.  
The information in this manual has been carefully checked and is believed to be accurate. However, changes are made periodically. These  
changes are incorporated in newer publication editions. Gateway may improve and/or change products described in this publication at any  
time. Due to continuing system improvements, Gateway is not responsible for inaccurate information which may appear in this manual. For  
the latest product updates, consult the Gateway Web site at www.gateway.com. In no event will Gateway be liable for direct, indirect,  
special, exemplary, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the  
possibility of such damages.  
In the interest of continued product development, Gateway reserves the right to make improvements in this manual and the products it  
describes at any time, without notices or obligation.  
Trademark Acknowledgments  
Gateway and eMachines are trademarks or registered trademarks of Gateway, Inc. in the United States and other countries. All other brands  
and product names are trademarks or registered trademarks of their respective companies.  
15  
 
 
Notices  
16  
 
 
MAN VX760/765 USR GDE R1 11/05  
 

Echo Brush Cutter SRM 210 User Manual
Eiki Flat Panel Television PLD 42UE User Manual
Eiki Projector LC 4300 User Manual
Eizo Computer Monitor F67 User Manual
Fostex Portable Speaker FE103E User Manual
Fujioh Ventilation Hood BUF 0 User Manual
Furuno Marine Radio DSC 5 User Manual
Garmin Marine GPS System 4010 User Manual
GE Clothes Dryer DBSR463G User Manual
Global Machinery Company Saw LSSCR User Manual