Installation
Instructions
Advantium® 120V
Built-In SpeedCook
Ovens
PSB1200
PSB1201
ZSC1201
ZSC1202
For a Spanish version of this manual, visit our Website at ge.com.
Para consultar una version en español de este manual de instrucciones,
visite nuestro sitiode internet ge.com.
49-40593-1
MFL59060901
12-08 JR
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
21-1/2″
29-3/4″
1-1/8″
19″
13/16″
5/8″
13″
ADVANCE PLANNING
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
• #2 Phillips screwdriver
• Hand-held drill
• High speed drill bit, 3/32″ diameter
• 3/8″ slot-head screwdriver
• Level
• These ovens may be installed directly into a 30″ wide
oven cabinet.
• Cutout dimensions are NOT the same for installation
with or without an accessory storage drawer.
Make sure to use the correct cutout when preparing
the opening.
NOTE: ZSC1202 models CANNOT be installed
with an accessory storage drawer. See Installation
Preparation Without an Accessory Storage Drawer
for this model.
• Saw
• 2 x 4 or 2 x 2 lumber for installing runners
or 3/8″ plywood for floor (if required)
• Wood screws or other hardware for installing
• Allow for clearance to adjacent corners, walls,
drawers, etc.
runner or shelf to support oven (if required)
• Safety glasses or goggles
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone
to climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessory Storage Drawer
Assembly Instructions.
PARTS SUPPLIED
• 6 screws (3 required, 3 extra)
• 5 color-matched screws (4 required, 1 extra)
• Bottom trim (2)
3
Installation Preparation
ELECTRICAL REQUIREMENTS
Single Advantium 120 Installation:
This product requires a 120-volt, 60 Hz, 15-amp circuit
and draws 1.8 kilowatts. This product must be
connected to a supply circuit of the proper voltage
and frequency.
• Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating.
• The power supply cord and plug should be brought
to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 48" power cord.
IMPORTANT: (Please read carefully).
ELECTRICAL LOCATION
The power cord of this appliance is equipped with
a three-prong (grounding) plug that mates with
a standard three-prong grounding wall receptacle
to minimize the possibility of electric shock. The
customer should have the wall receptacle and
circuit checked by a qualified electrician to make
sure the receptacle is properly grounded and has
the correct polarity.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with
a properly grounded three-prong wall receptacle.
6”
9”
Locate outlet box in the shaded area
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Install a recessed electrical outlet in the back wall
of the opening within 6″ of either side and at least
9″ above the cutout floor.
DO NOT USE AN EXTENSION CORD.
4
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING
PREPARE THE OPENING (cont.)
The Advantium 120V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Installation over a GE/Monogram
Warming Drawer:
30″
23-1/2″
Construct
Single Advantium 120V Installation:
Order a 30″ wide single oven cabinet or cut
the opening in a wall to the dimensions shown.
Solid Bottom
Min. 3/8″
Plywood
Supported
by 2 x 4 or 2 x 2
Runners all
Four Sides
25-1/4″
30″
23-1/2″
17-1/2″
2″ Min.
(3″ Recommended)
25-1/4″
Per Warming
Drawer
Requirement
17-1/2″
Construct
Base
Min. 3/8″
Plywood
Supported
by 2 x 4 or
2 x 2 Runners
all Four Sides
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
• Allow 2-1/8″ case trim overlap on the sides,
1-1/16″ overlap on the top and 7/8″ overlap
on the bottom of the opening for all models.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2″ between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120V and the other
appliance overlaps.
Construct a solid oven floor of 3/8″ min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
5
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (cont.)
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram oven:
Installation over a GE/Monogram Oven and
Warming Drawer:
30″
23-1/2″
30″
23-1/2″
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
25-1/4″
25-1/4″
Four Sides
Four Sides
17-1/2″
2″ Min.
(3″ Recommended)
17-1/2″
2″ Min.
(3″ Recommended)
Per Oven
Requirement
Per Oven
Requirement
2″ Min.
(3″ Recommended)
Per Warming
Drawer Requirement
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium 120V and a single oven, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION:
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
6
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (cont.)
PREPARE THE OPENING (cont.)
Installation over another GE/Monogram
Installation under a GE/Monogram
Microwave Oven and over a Warming
Drawer:
Under-the-Counter (UTC) oven:
23-1/2″
30″
30″
23-1/2″
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
25-1/4″
25-1/4″
Four Sides
Four Sides
17-1/2″
2″ Min.
(3″ Recommended)
Per Oven
3.5″ Min.
(4.5″ Recommended)
Requirement
17-1/2″
17-1/2″
2″ Min.
(3″ Recommended)
Per Warming
Drawer Requirement
• If you are mounting an Under-the-Counter
GE/Monogram oven over another, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION:
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
7
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
23-1/2″
PREPARE THE OPENING (cont.)
Installation beside another GE/Monogram
Built-in Speedcook Oven:
• If you are mounting one Under-the-Counter
GE/Monogram oven beside the other, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 4-1/2″ minimum shown.
25-1/4″
25-1/4″
17-1/2″
17-1/2″
4-1/2″ Min.
(5-1/2″ Recommended)
PREPARE THE OPENING (cont.)
Installation under a GE/Monogram 30″ or 36″ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout
size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly
grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36″
or wider base cabinet.
1-1/2″ Min.
25″
Cooktop
Cooktop
″
36
Countertop
Height
″
17-1/2
″
25-1/4
Cooktop height including depth
of electrical box on some models.
Refer to cooktop installation
instructions.
No minimum clearance required
between cooktop and oven.
″
23-1/2
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
4″ High
Toekick
8
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4
″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (cont.)
PREPARE THE OPENING (cont.)
The Advantium 120V can be installed in
combination with other GE/Monogram appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Installation over a GE/Monogram
Warming Drawer:
23-1/2″
30″
Single Advantium 120V Installation:
Order a 30″ wide single oven cabinet or cut
the opening in a wall to the dimensions shown.
Construct Solid
Bottom Min. 3/8″
Plywood Supported
by 2 x 4 or 2 x 2
25-1/4″
Min.
30″
23-1/2″
Runners all Four Sides
21″
2″ Min.
(3″ Recommended)
25-1/4″
Min.
Per Warming
Drawer
Requirement
36-3/4″
Min.*
21″
*Required for
Construct Base
Min. 3/8″ Plywood
Supported by 2 x 4
or 2 x 2 Runners
all Four Sides
Monogram models
36-3/4″
Min.*
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
*Required for
Monogram models
• Allow 2-1/8″ case trim overlap on the sides,
1-1/16″ overlap on the top and 7/8″ overlap
on the bottom of the opening for all models.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2″ between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120V and the other
appliance overlaps.
Construct a solid oven floor of 3/8″ min. thick plywood
supported by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
9
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4
″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (cont.)
PREPARE THE OPENING (cont.)
Installation over a GE/Monogram Oven:
Installation over a GE/Monogram Oven and
Warming Drawer:
30″
23-1/2″
30″
23-1/2″
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
25-1/4″
Min.*
25-1/4″
Min.*
Four Sides
Four Sides
21″
2″ Min.
(3″ Recommended)
21″
2″ Min.
(3″ Recommended)
Per Oven
Requirement
Per Oven
Requirement
36-3/4″
Min.
45-1/4″
45-1/4″
2″ Min.
(3″ Recommended)
Recommended*
*Required for
Monogram models
Per Warming
Drawer Requirement
* For existing cutouts, a maximum width of 28-1/2″
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium 120V and a single oven, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
* For existing cutouts, a maximum width of 28-1/2″
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION:
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30-pound
drawer, plus additional oven loads of up to
50 pounds or a total weight of 160 pounds.
10
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4
″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (cont.)
PREPARE THE OPENING (cont.)
Installation over another GE/Monogram
Installation under a GE/Monogram
Microwave Oven and over a Warming
Drawer:
Under-the-Counter (UTC) oven:
30″
23-1/2″
23-1/2″
30″
Construct Solid
Bottom Min.
3/8″ Plywood
Supported by
2 x 4 or 2 x 2
Runners all
Construct Solid
Bottom Min. 3/8″
Plywood Supported
by 2 x 4 or 2 x 2
Runners all Four
Sides
25-1/4″
25-1/4″
Four Sides
21″
2″ Min.
(3″ Recommended)
Per Oven
Requirement
3.5″Min.
(4.5″Recommended)
21″*
21″*
2″ Min.
*Profile models only
(3″ Recommended)
Per Warming
Drawer Requirement
*Profile models only
• If you are mounting an Under-the-Counter
GE/Monogram oven over another, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2″ minimum shown.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
CAUTION:
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds
or a total weight of 130 pounds.
11
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4
″.
MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT
AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
23-1/2″
PREPARE THE OPENING (cont.)
Installation beside another GE/Monogram
Built-in Speedcook Oven:
• If you are mounting one Under-the-Counter
GE/Monogram oven beside the other, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than
the 4-1/2″ minimum shown.
25-1/4″
25-1/4″
21″
21″
4-1/2″ Min.
(5-1/2″ Recommended)
PREPARE THE OPENING (cont.)
Installation under a GE Profile 30″ or 36″ Cooktop or Countertop:
Gas or electric cooktops may be installed
over this oven. See cooktop installation
1-1/2″ Min.
25″
Cooktop
instructions for the cutout size. See the
label on top of the oven for approved
cooktop models. This oven requires
a separate, properly
Cooktop
″
36
grounded 15-Amp,
Countertop
Height
120-Volt, 60Hz power
supply. The cooktop
requires a separate power
supply. Use a 36″ or wider
base cabinet.
IMPORTANT:
For Profile models only.
The Monogram oven
and drawer combination
cannot be installed below
a countertop.
″
21
″
25-1/4
Cooktop height including depth
of electrical box on some models.
Refer to cooktop installation
instructions.
No minimum clearance required
between cooktop and oven.
″
23-1/2
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
4″ High
Toekick
12
Installation Instructions
1 REMOVE THE PACKAGING AND PARTS
• Remove all packing material and tape.
• Locate parts package containing mounting screws.
• Remove the oven from the carton. Do not lift unit
by handle or conduit. Two people are required to lift
this oven.
• Open the door and remove any packaging in oven.
Rack
CAUTION:
If installing the Advantium
Owner’s
Manual
120V Oven below 36″, you must use the plastic
bottom trim due to burn risk to children. The
plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.
Installation
Instructions
Owner’s Manual
Bottom Trim – Plastic
Bottom Trim – Metal
Cooking
Guide
Cook Book
Glass Tray
Cooking Guide
Turntable Ring
5 Color-Matched Screws
(4 required, 1 extra)
6 Brass Screws
(3 required, 3 extra)
IMPORTANT: If installing the Advantium 120V Oven
with an accessory storage drawer, read the storage
drawer assembly instructions to assemble the
products together before proceeding to Step 2.
Metal Trays (2)
13
Installation Instructions
2 DOOR TRIM REMOVAL FOR ABOVE
3 SLIDE THE OVEN INTO THE CUTOUT
36″ INSTALLATION ONLY
CAUTION:
Two people are required to
If installing the Advantium 120V Oven above 36″
from the floor, you may remove the plastic trim
from the bottom of the door for esthetic purposes
if desired.
lift the oven into the opening. Grasp the bottom
at front and rear. DO NOT USE THE HANDLE TO LIFT
THE OVEN. DAMAGE WILL OCCUR.
CAUTION:
If installing the Advantium
120V Oven below 36″, do not remove the
plastic door trim due to burn risk to children.
The plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.
• If installing above 36″, remove the 3 screws that
secure the plastic trim to the bottom of the door.
• Discard plastic trim. Replace screws.
• Lift and hold the oven at the front of the opening.
Hold the oven at an angle and plug in the power
cord.
• Carefully, slide the oven into the cabinet part
way. Leave the oven a few inches forward of
the cabinet frame.
• Check to be sure the power cord is not trapped
under the oven or along the sides of the oven.
14
Installation Instructions
4 INSTALL BOTTOM TRIM
6 INSTALL MOUNTING SCREWS
CAUTION:
If installing the Advantium
120V Oven below 36″, you must use the plastic
bottom trim due to burn risk to children. The plastic
trim acts as insulation and will help prevent burns
to children from hot surfaces.
NOTE: If installing the Advantium 120V Oven
with an accessory storage drawer, the bottom trim
is not required. Proceed to Step 5.
• Installation Below 36″, align trim tabs on the plastic
trim to slots in the bottom of the oven.
• Slide the oven the remaining way into the opening
so that the side flanges and control panel are
against the cabinet frame. Make sure that the oven
is centered in the opening.
• Open the door, place a turntable tray in the oven
and make sure that the tray in the unit is level.
• Drill pilot holes through the side flanges.
Plastic Trim
• Drive the color-matched screws into the side
flanges. It is recommended that the screws
be hand tightened.
• Installation Above 36″, align trim tabs on the plastic
or metal trim to slots in the bottom of the oven.
If installing oven with an accessory storage
drawer:
• Open the drawer.
• Drill pilot holes through the side flanges.
Plastic Trim
OR
Metal Trim
• Drive color-matched screws into the side flanges.
It is recommended that the screws be hand
tightened.
• Secure the bottom trim to the bottom of the oven
using 3 screws provided.
NOTE: If installing the Profile Advantium 120V Oven
with an accessory storage drawer, you must use
the Under-the-Counter (UTC) mounting bracket for
the drawer.
If installing the Monogram Advantium integrated
model ZSC1201 above 36″, the UTC mounting bracket
for the accessory storage drawer must be used.
5 INSTALL BOTTOM TRIM WITH
ACCESSORY DRAWER
If installing with an accessory drawer, see
installation instructions on page 17 or instructions
that come with the accessory drawer.
7 FINALIZE INSTALLATION
• Turn power on at the source. The interior light
should come on when the door is opened.
• Refer to Owner’s Manual for operating instructions.
15
GE Consumer & Industrial Appliances
Assembly Instructions
Advantium® Built-In Accessory Storage Drawer
JX2200, JX2201, ZX2201
MODELS AVAILABLE
BEFORE YOU BEGIN
Profile Models:
Read these instructions completely and carefully. Read
JX2200BB–Black
the Installation Instructions for the Advantium 120V or
240V oven completely and carefully for cutout
dimensions and step-by-step instructions.
JX2201SS–Stainless Steel
Monogram Models:
IMPORTANT — Save these instructions for
ZX2201SS–Stainless Steel (for installation above 36″ only)
local inspector’s use.
NOTE: Advantium 240V model ZSC2202SS and
Advantium 120V model ZSC1202 CANNOT be
installed with an accessory storage drawer. See
Installation Preparation Without an Accessory Storage
Drawer in the Installation Instructions for these models.
IMPORTANT — Observe all governing codes
and ordinances.
• NOTE TO INSTALLER: Be sure to leave these
instructions with the Consumer.
• NOTE TO CONSUMER: Keep these instructions with
your Advantium 120V or 240V Oven Owner’s Manual
for future reference.
PRODUCT DIMENSIONS AND CLEARANCES
• SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.
5″
• COMPLETION TIME: One hour with the installation
of an Advantium 120V or 240V oven.
Allow 15″ clearance
when fully open
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty. See the Advantium
120V or 240V Oven Owner’s Manual for warranty
information.
NOTE: Appearance will vary by model.
TOOLS REQUIRED
• #2 Phillips screwdriver
PARTS SUPPLIED
• 2 Side Supports
• Screws (8)
• Screws (color-matched) (5)
• Under-the-Counter Mounting Bracket (1)
16
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN
1 REMOVE PACKAGING AND PARTS
3 ASSEMBLING THE OVEN TO DRAWER
Place storage drawer on a surface with
the front of drawer hanging over the edge
of the surface. Not placing the front edge
of drawer over the edge of the surface may
result in damage to the drawer since the front
edge of drawer hangs below the bottom
of drawer.
A
• Remove the drawer from the carton.
• Remove all packing material and tape.
• Open the drawer and remove any parts inside.
• Locate parts.
Place the oven on top of the storage drawer.
Make sure that the back and sides of the oven
align with the back and sides of drawer.
B
Side Supports (2)
Assembly Instructions
Under-the-Counter (UTC)
Mounting Bracket
Screws
(6 required,
2 extra)
Color-Matched
Screws
(4 required,
1 extra)
NOTE: The bottom of the oven side flanges will
sit directly in front of the top of the storage
drawer side flanges.
2 UNDER-THE-COUNTER (UTC)
MOUNTING BRACKET INSTALLATION
NOTE: For UTC models PSB1200, PSB1201 and
ZSC1201 only.
Open the accessory drawer so you have
access to the top bracket.
A
B
C
Remove the three screws securing the top
bracket.
Install the new UTC mounting bracket using
the screws removed previously.
Close the drawer and proceed with the
installation.
D
17
ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN
ASSEMBLING THE OVEN TO DRAWER
(cont.)
Remove the front two bottom screws on each
side of the oven and the top center screw on
each side of the storage drawer.
C
Place the side supports into the tabs on the
drawer and secure using the screws supplied
and the screws removed in Step C.
D
Side
Support
120v only
The oven and storage drawer assembly is now
ready to be installed. Return to the Advantium
120V or 240V Built-In SpeedCook Oven
Installation Instructions to complete
the installation.
E
18
Notes
19
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Printed in Korea
|