ZBd6890NII
GE Monogram® Fully Integrated Built-In dishwasher
Dimensions and Specifications (in inches)
Custom Panel for Model ZBD6890NII
These dishwashers require a field installed 3/4” thick custom
panel and custom handle. An installation template is
packed with these models and may be obtained in advance.
Order Pub. No. 31-30569-1. Complete panel installation
instructions are included on the template.
• The dishwasher must be installed so that the drain hose
is no more than 10 feet in length for proper drainage.
• Water and power supply should enter in the
shaded area.
• Electrical and water connections are at the right front
of the dishwasher. The hot water line should extend
forward 30" to 40" from the rear wall. The electrical
must extend forward at least 24" to reach the junction
box.
CUSTOM PANEL SIZE REQUIREMENTS
HEIGHT
Panel height must
be between
30-1/16" and 30-1/4".
• To prevent siphoning, an air gap must be used when
the waste tee or disposer connection is less than 18"
above the floor.
• If the panel height is
more than 30-1/4” it
30-1/16" Min.
30-1/4" Max.
will prevent the door
from swinging open.
• If the panel height is
less than 30-1/16” it
will not cover the
dishwasher door
This Wall Area
must be Free of
23-3/4"
Pipes or wires
Cabinets
24"
34-1/2" Min.
Underside of
Countertop
to Floor
Square
and
5"
5"
Min.
4"
frame.
4"
• The top of the custom panel must be flush with the top
of the door. The 1/2” minimum gap between the top
of the door and the bottom of the countertop must be
maintained.
Plumb
6"
24" Min.
34"
Countertop
Adjustable
to 35"
Floor MUST
be Even with
Room Floor
WIDTH
Panel width must be 23-3/4".
1/2" min.
• If the panel width is less than
23-3/4” it will not cover the
dishwasher frame.
Minimum 1/2" gap
for Clearance
*24"
24"
*dishwasher models
ZBd6890 and ZBd0700
require a 3/4" thick
custom panel and will be
24-3/4" deep.
IMPORTANT: To ensure
optimum door balance
performance, the custom panel must not weigh
more than 14 lbs.
Accessories for custom panel model ZBD6890
ZPR0700S door panel provides a professional-style handle
on a stainless steel door panel.
ZTB700 stainless steel tubular handle for installation onto a
custom panel.
Electrical Requirements
The dishwasher must be supplied with 120V, 60Hz, and
connected to an individual properly grounded branch
circuit protected by a 15- or 20-amp circuit breaker or
time-delay fuse.
Before installing refer to installation instructions for
details. Pub. No. 31-30586
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
As an EnErgy StAr®
Listed by
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
Underwriters
Laboratories
Specification Revised 2/08
150043
ZBd6890NII
GE Monogram® Fully Integrated Built-In dishwasher
Features and Benefits
• Stainless Steel Interior
• Hidden, Integrated Top Controls
• Long door design
• Powerful Forced-air drying System
• CleanSensor Technology
• Nylon upper and Lower Racks
• NSF® Certified to Sanitize
• ENERGy STAR® Qualified
• Model ZBd6890NII – Requires custom panel
Specification Revised 2/08
150043
|