FUJITSU SEMICONDUCTOR
DATA SHEET
DS04-21358-4E
ASSP
Single Serial Input
PLL Frequency Synthesizer
On-chip 2.5 GHz Prescaler
MB15E07SL
■ DESCRIPTION
TheFujitsuMB15E07SLisaserialinputPhaseLockedLoop(PLL)frequencysynthesizerwitha2.5GHzprescaler.
The 2.5 GHz prescaler has a dual modulus division ratio of 32/33 or 64/65 enabling pulse swallowing operation.
The supply voltage range is between 2.4 V and 3.6 V. The MB15E07SL uses the latest BiCMOS process, as a
result the supply current is typically 3.5 mA at 2.7 V. A refined charge pump supplies well-balanced output currents
of 1.5 mA and 6 mA. The charge pump current is selectable by serial data.
MB15E07SL is ideally suited for wireless mobile communications, such as GSM (Global System for Mobile
Communications) and PCS.
■ FEATURES
• High frequency operation: 2.5 GHz Max
• Low power supply voltage: VCC = 2.4 to 3.6 V
• Ultra Low power supply current: ICC = 3.5 mA Typ (VCC = Vp = 2.7 V, Ta = +25°C, in locking state)
ICC = 4.0 mA Typ (VCC = Vp = 3.0 V, Ta = +25°C, in locking state)
• Direct power saving function: Power supply current in power saving mode
Typ 0.1 µA (VCC = Vp = 3.0 V, Ta = +25°C), Max 10 µA (VCC = Vp = 3.0 V)
(Continued)
■ PACKAGES
16-pin plastic SSOP
16-pad plastic BCC
(FPT-16P-M05)
(LCC-16P-M06)
MB15E07SL
■ PIN DESCRIPTIONS
Pin no.
Pin
I/O
Descriptions
name
SSOP
BCC
16
1
1
2
3
4
OSCIN
OSCOUT
VP
I
Programmable reference divider input. Connection to a TCXO.
Oscillator output.
O
–
–
2
Power supply voltage input for the charge pump.
Power supply voltage input.
3
VCC
Charge pump output.
Phase of the charge pump can be selected via programming of the FC bit.
5
4
DO
O
6
7
5
6
GND
Xfin
–
I
Ground.
Prescaler complementary input, which should be grounded via a capacitor.
Prescaler input.
8
7
fin
Clock
Data
LE
I
I
I
I
Connection to an external VCO should be done via AC coupling.
Clock input for the 19-bit shift register.
Data is shifted into the shift register on the rising edge of the clock.
(Open is prohibited.)
9
8
Serial data input using binary code.
The last bit of the data is a control bit. (Open is prohibited.)
10
11
9
Load enable signal input. (Open is prohibited.)
When LE is set high, the data in the shift register is transferred to a latch
according to the control bit in the serial data.
10
Power saving mode control. This pin must be set at “L” at Power-ON.
(Open is prohibited.)
PS = “H”; Normal mode
12
13
14
11
12
13
PS
ZC
I
I
PS = “L”; Power saving mode
Forced high-impedance control for the charge pump (with internal pull up
resistor.)
ZC = “H”; Normal Do output.
ZC = “L”; Do becomes high impedance.
Lock detect signal output (LD)/phase comparator monitoring output (fout).
The output signal is selected via programming of the LDS bit.
LDS = “H”; outputs fout (fr/fp monitoring output)
LD/fout
O
LDS = “L”; outputs LD (“H” at locking, “L” at unlocking.)
Phase comparator N-channel open drain output for an external charge
pump. Phase can be selected via programming of the FC bit.
15
16
14
15
φP
φR
O
O
Phase comparator CMOS output for an external charge pump. Phase can
be selected via programming of the FC bit.
3
MB15E07SL
■ BLOCK DIAGRAM
fr
(16)
1
(15)
16
OSCIN
φR
φP
Reference
oscillator
circuit
Phase
comparator
(14)
15
(1)
2
OSCOUT
Lock
detector
SW FC
CS
LDS
Binary 14-bit
reference counter
(13)
14 LD/fout
(2)
3
LD/fr/fp
selector
14-bit latch
. .
4-bit latch
VP
fp
C
19-bit shift register
N
T
(12)
13
(3)
4
ZC
PS
VCC
. . .
. . .
7-bit latch
11-bit latch
(11)
12
(4)
5
Intermittent
mode control
(power save)
DO
Binary 11-bit
programmable
counter
Binary 7-bit
swallow counter
(10)
11 LE
(5)
6
GND
1-bit
control
latch
(9)
10
(6)
7
Data
Xfin
fin
MD
Prescaler
32/33
64/65
(7)
8
(8)
9
Clock
: SSOP
) : BCC
(
4
MB15E07SL
■ ABSOLUTE MAXIMUM RATINGS
Rating
Parameter
Symbol
Condition
Unit
Remark
Min
–0.5
VCC
Max
4.0
VCC
VP
–
V
V
Power supply voltage
Input voltage
–
6.0
VI
–
–0.5
GND
GND
–55
VCC +0.5
VCC
V
VO
Except Do
V
Output voltage
VO
Do
–
VP
V
Storage temperature
Tstg
+125
°C
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
Value
Parameter
Symbol
Unit
Remark
Min
2.4
Typ
3.0
–
Max
3.6
VCC
VP
VI
V
V
Power supply voltage
VCC
5.5
Input voltage
GND
–40
–
VCC
+85
V
Operating temperature
Ta
–
°C
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
5
MB15E07SL
■ ELECTRICAL CHARACTERISTICS
(VCC = 2.4 to 3.6 V, Ta = –40 to +85°C)
Value
Unit
Parameter
Symbol
Condition
Min
Typ
Max
fin = 2500 MHz, VCC = VP = 2.7 V
(VCC = VP = 3.0 V)
3.5
(4.0)
0.1*2
Power supply current*1
Power saving current
ICC
–
–
mA
*1
IPS
fIN
ZC = “H” or open
–
700
3
10
2500
40
µA
fin
–
–
–
MHz
MHz
Operating frequency
OSCIN OSCIN
–
50 Ω system
*3
fin
Pfin (Refer to the measurement
circuit.)
–15
–
+2
dBm
Vp-p
Input sensitivity
*3
OSCIN
VOSC
–
–
0.5
–
–
VCC
“H” level input voltage
“L” level input voltage
Data,
Clock,
LE,PS,
ZC
VIH
VCC × 0.7
–
V
VIL
–
–
–
VCC × 0.3
*4
“H” level input current
“L” level input current
Data,
Clock,
LE, PS
IIH
–
–
–1.0
–1.0
–
–
+1.0
+1.0
µA
µA
*4
IIL
“H” level input current
“L” level input current
“H” level input current
“L” level input current
“L” level output voltage
“H” level output voltage
“L” level output voltage
“H” level output voltage
“L” level output voltage
IIH
–
–
–
0
–100
–1.0
–100
–
–
–
–
–
–
–
–
–
–
+100
0
OSCIN
*4
IIL
*4
IIH
+1.0
0
ZC
µA
V
*4
IIL
Pull up input
φP
VOL
VOH
Open drain output
0.4
–
VCC = VP = 3.0 V, IOH = –1 mA
VCC = VP = 3.0 V, IOL = 1 mA
VCC – 0.4
–
φR,
LD/fout
V
VOL
0.4
–
VDOH
VDOL
VCC = VP = 3.0 V, IDOH = –0.5 mA VP – 0.4
Do
V
VCC = VP = 3.0 V, IDOL = 0.5 mA
–
0.4
High impedance cutoff
current
VCC = VP = 3.0 V,
VOFF = 0.5 V to VP – 0.5 V
Do
IOFF
–
–
2.5
nA
“L” level output current
“H” level output current
“L” level output current
φP
IOL
IOH
IOL
Open drain output
1.0
–
–
–
–
–1.0
–
mA
–
–
φR,
LD/fout
mA
mA
1.0
–
–
CS bit = “H”
–6.0
–1.5
6.0
1.5
3
–
*4
VCC = 3 V,
“H” level output current
“L” level output current
IDOH
CS bit = “L”
CS bit = “H”
CS bit = “L”
–
–
VP = 3 V,
VDO = VP/2
Ta = +25°C
Do
–
–
IDOL
–
–
*5
IDOL/IDOH IDOMT
VDO = VP/2
–
–
%
%
%
Charge pump current
rate
*6
IDOVD
vs VDO
vs Ta
0.5 V ≤ VDO ≤ VP – 0.5 V
– 40°C ≤ Ta ≤ +85°C
–
10
10
–
*7
IDOTA
–
–
*1 : Conditions; fosc = 12 MHz, Ta = +25°C, in locking state.
*2 : VCC = VP = 3.0 V, fosc = 12.8 MHz, Ta = +25°C, in power saving mode
6
MB15E07SL
*3 : AC coupling. 1000 pF capacitor is connected under the condition of Min operating frequency.
*4 : The symbol “–” (minus) means direction of current flow.
*5 : VCC = VP = 3.0 V, Ta = +25°C (|I3| – |I4|) / [(|I3| + |I4|) /2] × 100(%)
*6 : VCC = VP = 3.0 V, Ta = +25°C [(|I2| – |I1|) /2] / [(|I1| + |I2|) /2] × 100(%) (Applied to each IDOL, IDOH)
*7 : VCC = VP = 3.0 V, VDO = VP/2 (|IDO(85°C) – IDO(–40°C)| /2) / (|IDO(85°C) + IDO(–40°C)| /2) × 100(%) (Applied to each IDOL, IDOH)
I1
I3
I2
IDOL
IDOH
I4
I2
I1
0.5
Vp/2
Vp − 0.5 V
Vp
Charge Pump Output Voltage (V)
7
MB15E07SL
■ FUNCTIONAL DESCRIPTION
1. Pulse Swallow Function
The divide ratio can be calculated using the following equation:
fVCO = [(M × N) + A] × fOSC ÷ R (A < N)
fVCO : Output frequency of external voltage controlled oscillator (VCO)
N
A
: Preset divide ratio of binary 11-bit programmable counter (3 to 2,047)
: Preset divide ratio of binary 7-bit swallow counter (0 ≤ A ≤ 127)
fOSC : Output frequency of the reference frequency oscillator
R
M
: Preset divide ratio of binary 14-bit programmable reference counter (3 to 16,383)
: Preset divide ratio of modulus prescaler (32 or 64)
2. Serial Data Input
Serial data is processed using the Data, Clock, and LE pins. Serial data controls the programmable reference
divider and the programmable divider separately.
Binary serial data is entered through the Data pin.
One bit of data is shifted into the shift register on the rising edge of the Clock. When the LE signal pin is taken
high, stored data is latched according to the control bit data as follows:
Table 1. Control Bit
Control bit (CNT)
Destination of serial data
For the programmable reference divider
For the programmable divider
H
L
(1) Shift Register Configuration
Programmable Reference Counter
LSB
1
MSB
Data Flow
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
C
N
T
R
1
R
2
R
3
R
4
R
5
R
6
R
7
R
8
R
9
R
R
R
R
R
10 11 12 13 14 SW FC LDS CS
CNT
: Control bit
[Table 1]
R1 to R14 : Divide ratio setting bit for the programmable reference counter (3 to 16,383)
[Table 2]
[Table 5]
[Table 8]
[Table 7]
[Table 6]
SW
FC
LDS
CS
: Divide ratio setting bit for the prescaler (32/33 or 64/65)
: Phase control bit for the phase comparator
: LD/fOUT signal select bit
: Charge pump current select bit
Note: Start data input with MSB first.
8
MB15E07SL
Programmable Counter
MSB
LSB
1
Data Flow
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
C
N
T
A
1
A
2
A
3
A
4
A
5
A
6
A
7
N
1
N
2
N
3
N
4
N
5
N
6
N
7
N
8
N
9
N
N
10 11
CNT
: Control bit
[Table 1]
[Table 3]
[Table 4]
N1 to N11 : Divide ratio setting bits for the programmable counter (3 to 2,047)
A1 to A7 : Divide ratio setting bits for the swallow counter (0 to 127)
Note: Data input with MSB first.
Table 2. Binary 14-bit Programmable Reference Counter Data Setting
Divide ratio (R) R14 R13 R12 R11 R10 R9
R8
0
R7
0
R6
0
R5
R4
0
R3
0
R2
1
R1
1
3
0
0
⋅
0
0
⋅
0
0
⋅
0
0
⋅
0
0
⋅
0
0
⋅
0
0
⋅
4
⋅
0
0
0
0
1
0
0
⋅
⋅
⋅
⋅
⋅
⋅
⋅
16383
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note : Divide ratio less than 3 is prohibited.
Table 3. Binary 11-bit Programmable Counter Data Setting
Divide ratio (N)
N11
N10
N9
0
N8
0
N7
0
N6
N5
0
N4
0
N3
N2
1
N1
3
0
0
⋅
0
0
⋅
0
0
⋅
0
1
⋅
1
0
⋅
4
⋅
0
0
0
0
0
0
⋅
⋅
⋅
⋅
⋅
⋅
2047
1
1
1
1
1
1
1
1
1
1
1
Note : Divide ratio less than 3 is prohibited.
Table 4. Binary 7-bit Swallow Counter Data Setting
Divide ratio (A)
A7
0
A6
0
A5
A4
0
A3
0
A2
A1
0
1
0
0
⋅
0
0
⋅
0
1
⋅
0
0
0
0
⋅
⋅
⋅
⋅
⋅
127
1
1
1
1
1
1
1
9
MB15E07SL
Table 5. Prescaler Data Setting
SW
Prescaler divide ratio
H
L
32/33
64/65
Table 6. Charge Pump Current Setting
CS
Current value
±6.0 mA
H
L
±1.5 mA
Table 7. LD/fout Output Select Data Setting
LDS
LD/fOUT output signal
H
L
fout signal
LD signal
(2) Relation between the FC Input and Phase Characteristics
The FC bit changes the phase characteristics of the phase comparator. Both the internal charge pump output
level (DO) and the phase comparator output (φR, φP) are reversed according to the FC bit. Also, the monitor pin
(fOUT) output is controlled by the FC bit. The relationship between the FC bit and each of DO, φR, and φP is shown
below.
Table 8. FC Bit Data Setting (LDS = “H”)
FC = High
FC = Low
φR
DO
H
φR
φP
L
LD/fout
DO
L
φP
Z*
L
LD/fout
fr > fP
fr < fP
fr = fP
L
H
L
H
L
L
L
Z*
Z*
fout = fr
H
fout = fp
Z*
Z*
Z*
* : High-Z
10
MB15E07SL
When designing a synthesizer, the FC pin setting depends on the VCO and LPF characteristics.
* : When the LPF and VCO characteristics are similar
to (1), set FC bit high.
(1)
* : When the VCO characteristics are similar to (2), set
FC bit low.
VCO
Output
Frequency
PLL
LPF
VCO
(2)
LPF Output Voltage
3. Do Output Control
Table 9. ZC Pin Setting
ZC pin
Do output
H
L
Normal output
High impedance
4. Power Saving Mode (Intermittent Mode Control Circuit)
Table 10. PS Pin Setting
PS pin
Status
H
L
Normal mode
Power saving mode
The intermittent mode control circuit reduces the PLL power consumption.
By setting the PS pin low, the device enters into the power saving mode, reducing the current consumption. See
the Electrical Characteristics chart for the specific value.
The phase detector output, Do, becomes high impedance.
For the signal PLL, the lock detector, LD, remains high, indicating a locked condition.
Setting the PS pin high, releases the power saving mode, and the device works normally.
The intermittent mode control circuit also ensures a smooth startup when the device returns to normal operation.
When the PLL is returned to normal operation, the phase comparator output signal is unpredictable. This is
because
of the unknown relationship between the comparison frequency (fp) and the reference frequency (fr) which can
cause a major change in the comparator output, resulting in a VCO frequency jump and an increase in lockup
time.
To prevent a major VCO frequency jump, the intermittent mode control circuit limits the magnitude of the error
signal from the phase detector when it returns to normal operation.
When power (VCC) is first applied, the device must be in standby mode, PS = Low, for at least 1 µs.
11
MB15E07SL
Note : PS pin must be set “L” for Power-ON.
OFF
ON
≥
tV 1 µs
VCC
Clock
Data
LE
≥
tPS 100 ns
PS
(1)
(2)
(3)
(1) PS = L (power saving mode) at Power ON
(2) Set serial data 1 µs later after power supply remains stable (VCC > 2.2 V).
(3) Release power saving mode (PS: L → H) 100 ns later after setting serial data.
12
MB15E07SL
■ SERIAL DATA INPUT TIMING
1st data
2nd data
Control bit Invalid data
∼
∼
∼
Data
MSB
LSB
Clock
t1
t2
t3
t6
t7
LE
∼
t4
t5
On the rising edge of the clock, one bit of data is transferred into the shift register.
Parameter Min
Typ
–
Max Unit
Parameter Min
Typ
–
Max Unit
t1
t2
t3
t4
20
20
30
30
–
–
–
–
ns
ns
ns
ns
t5
t6
t7
100
20
–
–
–
ns
ns
ns
–
–
–
100
–
–
Note : LE should be “L” when the data is transferred into the shift register.
13
MB15E07SL
■ PHASE COMPARATOR OUTPUT WAVEFORM
fr
fp
tWU
tWL
LD
[FC = “H”]
DO
[FC = “L”]
DO
Notes : • Phase error detection range: –2π to +2π
• Pulses on Do signal during locked state are output to prevent dead zone.
• LD output becomes low when phase is tWU or more. LD output becomes high when phase error
is tWL or less and continues to be so for three cycles or more.
• tWU and tWL depend on OSCIN input frequency.
tWU > 2/fosc (s) (e. g. tWU > 156.3 ns, fosc = 12.8 MHz)
tWU < 4/fosc (s) (e. g. tWL < 312.5 ns, fosc = 12.8 MHz)
• LD becomes high during the power saving mode (PS = “L”).
14
MB15E07SL
■ MEASURMENT CIRCUIT (for Measuring Input Sensitivity fin/OSCIN)
1000 pF
0.1 µF
1000 pF
0.1 µF
1000 pF
S • G
S • G
fin
8
Xfin GND DO
VCC
VP OSCOUT OSCIN
50 Ω
50 Ω
7
6
5
4
3
2
1
9
10
11
12
13
14
15
16
Clock Data LE
φP
φR
PS
ZC LD/fout
VCC
Oscilloscope
Controller (setting divide ratio)
Note: SSOP-16
15
MB15E07SL
■ TYPICAL CHARACTERISTICS
1. fin input sensitivity
Input sensitivity − Input frequency (Prescaler: 64/65)
Ta = +25 °C
10
0
SPEC
−10
−20
−30
−40
−50
VCC = 2.4 V
VCC = 3.0 V
VCC = 3.6 V
0
200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Input frequency fin (MHz)
Input sensitivity − Input frequency (Prescaler: 32/33)
Ta = +25 °C
10
0
SPEC
−10
−20
−30
−40
−50
VCC = 2.7 V
VCC = 3.0 V
VCC = 3.6 V
0
200
400
600
800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000
Input frequency fin (MHz)
16
MB15E07SL
2. OSCIN input sensitivity
Input sensitivity − Input frequency
Ta = +25 °C
10
SPEC
0
−10
−20
−30
−40
−50
VCC = 2.4 V
VCC = 3.0 V
VCC = 3.6 V
−60
0
50
100
150
200
Input frequency fOSC (MHz)
17
MB15E07SL
3. Do output current
1.5 mA mode
VDO - IDO
Ta = +25°C
VCC = 3.0 V
Vp = 3.0 V
10.00
2.000
/div
IDOL
0
IDOH
–10.00
0
4.800
.6000/div
Charge pump output voltage VDO (V)
6.0 mA mode
VDO - IDO
Ta = +25°C
VCC = 3.0 V
Vp = 3.0 V
10.00
IDOL
2.000
/div
0
IDOH
–10.00
0
4.800
.6000/div
Charge pump output voltage VDO (V)
18
MB15E07SL
4. fin input impedance
1 : 12.646 Ω
–57.156 Ω
1 GHz
22.156 Ω
–12.136 Ω
1.5 GHz
2 :
3 :
4 :
4
33.805 Ω
11.869 Ω
2 GHz
23.715 Ω
8.9629 Ω
2.5 GHz
3
2
1
START
500.000 000 MHz
STOP 2 500.000 000 MHz
5. OSCIN input impedance
1 : 9.917 Ω
–3.643 Ω
3 MHz
3.7903 Ω
–4.812 Ω
10 MHz
2 :
3 :
4 :
1.574 Ω
–3.4046 Ω
20 MHz
4
3
2
1
453.12 Ω
–1.9213 Ω
40 MHz
START
1.000 000 MHz
STOP
50.000 000 MHz
19
MB15E07SL
■ REFERENCE INFORMATION
Test Circuit
fVCO = 810.45 MHz VCC =VP = 3.0 V
KV = 17 MHz/V
fr = 25 kHz
fOSC = 14.4 MHz
VVCO = 2.3 V
Ta = +25 °C
CP : 6 mA mode
S.G
OSCIN
fin
LPF
Do
LPF
9.1 kΩ
4.2 kΩ
0.047 µF
4700 pF
1500 pF
Spectrum
Analyzer
VCO
PLL Reference Leakage
ATT 10 dB
25.0 kHz
–78.0 dB
REF –5.0 dBm
10 dB/
MKR
RBW
1 kHz
SAMPLE
VBW
1 kHz
SWP 1.0 s
CENTER 810.000 MHz
SPAN 200 kHz
ATT 10 dB
PLL Phase Noise
2.28 kHz
–53.1 dB
REF –5.0 dBm
10 dB/
MKR
RBW
100 Hz
SAMPLE
VBW
100 Hz
SWP 10 s
CENTER 810.000 MHz
SPAN 20.0 kHz
(Continued)
20
MB15E07SL
(Continued)
PLL Lock Up time
1.30 ms
PLL Lock Up time
826 MH→810 MHz within ± 1 kHz
810 MH→826 MHz within ± 1 kHz
Hch→Lch
1.28 ms
Lch→Hch
846.000 MHz
838.000 MHz
826.000 MHz
806.000 MHz
818.000 MHz
798.000 MHz
500.0 µs/div
500.0 µs/div
810.004000MHz
826.004000 MHz
826.000000 MHz
810.000000MHz
809.996000MHz
825.996000 MHz
500.0 µs/div
500.0 µs/div
21
MB15E07SL
■ APPLICATION EXAMPLE
VP
10 kΩ
12 kΩ
OUTPUT
VCO
LPF
12 kΩ
10 kΩ
Lock Det.
From
a controller
φR
φP
ZC
13
LE
11
Data
10
Clock
9
LD/fout
14
PS
12
16
15
MB15E07SL
1
2
3
4
5
6
7
8
OSCOUT
OSCIN
VP
GND
fin
DO
Xfin
VCC
1000 pF
1000 pF
1000 pF
0.1 µF
0.1 µF
TCXO
VP: 5.5 V Max
Notes : • SSOP-16
• In case of using a crystal resonator, it is necessary to optimize matching between the crystal
and this LSI, and perform detailed system evaluation. It is recommended to consult with a
supplier of the crystal resonator. (Reference oscillator circuit provides its own bias, feedback
resistor is 100 kΩ (Typ).)
22
MB15E07SL
■ USAGE PRECAUTIONS
To protect against damage by electrostatic discharge, note the following handling precautions:
-Store and transport devices in conductive containers.
-Use properly grounded workstations, tools, and equipment.
-Turn off power before inserting device into or removing device from a socket.
-Protect leads with a conductive sheet when transporting a board-mounted device.
■ ORDERING INFORMATION
Part number
MB15E07SLPFV1
MB15E07SLPV1
Package
Remarks
16-pin, Plastic SSOP
(FPT-16P-M05)
16-pad, Plastic BCC
(LCC-16P-M06)
23
MB15E07SL
■ PACKAGE DIMENSIONS
Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max).
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
16-pin plastic SSOP
(FPT-16P-M05)
15.00±0.10(.197±.004)
*
0.17±0.03
(.007±.001)
16
9
2 4.40±0.10 6.40±0.20
(.173±.004) (.252±.008)
*
INDEX
Details of "A" part
1.25 +0.20
–0.10
(Mounting height)
.049 +.008
–.004
1
8
LEAD No.
"A"
0.65(.026)
0.24±0.08
(.009±.003)
M
0.13(.005)
0~8˚
0.10±0.10
(.004±.004)
(Stand off)
0.50±0.20
(.020±.008)
0.25(.010)
0.60±0.15
(.024±.006)
0.10(.004)
C
2003 FUJITSU LIMITED F16013S-c-4-6
Dimensions in mm (inches
)
Note : The values in parentheses are reference values.
(Continued)
24
MB15E07SL
(Continued)
16-pad plastic BCC
(LCC-16P-M06)
4.55±0.10
(.179±.004)
0.80(.031)MAX
Mounting height
3.40(.134)TYP
0.65(.026)
0.325±0.10
(.013±.004)
TYP
0.40±0.10
(.016±.004)
14
9
9
14
0.80(.031)
REF
INDEX AREA
3.40±0.10
(.134±.004)
2.45(.096)
TYP
1.15(.045)
REF
"B"
"A"
0.075±0.025
(.003±.001)
(Stand off)
1.725(.068)
REF
1
6
6
1
Details of "A" part
0.75±0.10
Details of "B" part
0.60±0.10
(.024±.004)
(.030±.004)
0.05(.002)
0.40±0.10
0.60±0.10
(.016±.004)
(.024±.004)
C
1999 FUJITSU LIMITED C16017S-1C-1
Dimensions in mm (inches
)
Note : The values in parentheses are reference values.
25
MB15E07SL
FUJITSU LIMITED
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information, such as descriptions of function and application
circuit examples, in this document are presented solely for the
purpose of reference to show examples of operations and uses of
Fujitsu semiconductor device; Fujitsu does not warrant proper
operation of the device with respect to use based on such
information. When you develop equipment incorporating the
device based on such information, you must assume any
responsibility arising out of such use of the information. Fujitsu
assumes no liability for any damages whatsoever arising out of
the use of the information.
Any information in this document, including descriptions of
function and schematic diagrams, shall not be construed as license
of the use or exercise of any intellectual property right, such as
patent right or copyright, or any other right of Fujitsu or any third
party or does Fujitsu warrant non-infringement of any third-party’s
intellectual property right or other right by using such information.
Fujitsu assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result
from the use of information contained herein.
The products described in this document are designed, developed
and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use,
personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could
have a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export
of those products from Japan.
F0306
FUJITSU LIMITED Printed in Japan
|