BATTERY DRIVE, MICRO LINE THERMAL PRINTER
2” TYPE MECHANISM AND INTERFACE BOARD
WITH MINIATURE CUTTER
FTP-624MCL303/304/FTP-624DSL113
■ OVERVIEW
FTP-624MCL303/304 is a high speed, battery driven thermal
printer with a miniature cutter, printing on 2-inch wide paper
(58mm/60mm). A newly developed, long life, compact, light
weight cutter has been partnered with a FTP-624MCL
mechanism to produce this new product.
The design allows easy maintenance, head cleaning, head
replacement, and cutter replacement.
This printer is suitable for a variety of applications, such as
hand held POS terminals, measurement and medical
FTP-624MCL303/304
instruments.
A dedicated LSI (microcontroller) for driving the printer or an
interface board mounting this LSI is also available.
■ HIGHLIGHTS
• Long life
Due to our proprietary cutter driving mechanism, the life of
the cutter is 300,000 cuts.
FTP-624CU
• High speed printing
It can print at 60 mm/s (480 dotlines) maximum by using
Fujitsu's unique head drive control.
• Paper auto loading function
Thermal paper can be loaded without head-up lever
operation.
• Two types of cut functions
Full and partial cut are possible.
• UL Recognized
File No. E171434
FTP-624DSL113
1
FTP-624MCL303/304/FTP-624DSL113
(Continued)
Item
For head
Specifications
Voltage: 4.2-8.5 VDC
Peak current: approx. 2.6 A (conditions: room temp., 7.2 VDC, 64 dots on)
Voltage: 4.2-8.5 VDC
Peak current: approx. 0.8 A (conditions: room temperature, 7.2 VDC)
For motor
Power
supply
Voltage: 5.0 VDC ± 5%
Current: 0.2 A maximum
For logic
For cutter
Voltage: 5.0 VDC ± 5%
Current: Approximately 5.0A (in-rush)
Approximately 1.0A (average)
Mechanism
97 (W) × 57 (D) × 38 (H) mm
131 (W) × 89 (D) × 24 (H) mm
Approximately 280 g
Dimensions
Interface board
Weight (Mechanism)
Mechanism
Pulse durability: 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard
driving method)
Expected life
Wear resistance: 50 km (at 25% print ratio)
Cutter
300,000 cuts minimum
Operating temperature
Operating humidity
Storage temperature
Storage humidity
Head temperature
0 to +50°C*1
20 to 85% RH (no condensation)
–20 to +60°C (excluding paper)
5 to 95% RH (no condensation)
By thermistor (applied energy control, abnormal temperature detection)
Environmental
conditions
Detection
Paper out/Mark detect
Head-up
By photointerrupter
By microswitch
For front insertion use (58 mm width) : FTP-020PU001, FTP-020P0104/
P0701
For rear insertion use (60 mm width) : FTP-020P0020, FTP-020P0105/
P0702
In Europe (58 mm width)
· Oji Paper
· NIPPON Paper
: FTP-021P0060-45
Recommended thermal sensitive paper
: PD150R, PD160R-N, PD170R
: TF50KS-E4,TF60KS-E,TF50KS-E
: P220VBB-1, AFP-235
· MITSUBISHI Paper Mills
*1: Guarantee +5°C to +40°C.
3
FTP-624MCL303/304/FTP-624DSL113
■ DIMENSIONS
Printer mechanism
Unit: mm
4
FTP-624MCL303/304/FTP-624DSL113
Interface board
130.8
120.7
105.4
71.1
33.0
5.1
5.1
15.2
CN9
CN10
CN6
CN5
4-ø3.6
CN3
CN11 CN1 CN2
CN4
5.1
56.7
69.9
86.4
5.1
105.4
120.7
17.0
1.6
5.0
Mounting height
Mounting height
23.6
Unit: mm
5
FTP-624MCL303/304/FTP-624DSL113
■ CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM
1. Thermal Head
Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent
Board side : PHR-16 (J.S.T.) or equivalent
*1: Symbol: " " means a negative logic signal
Thermal head heat sink
Motor
Head up level
1, 2, 3, ......................................15, 16
Connector Pin No.
2. Motor connectors
3. Sensor connectors
Motor side : PHR-4 (J.S.T.) or equivalent
Board side : B4B-PH-K-S (J.S.T.) or equivalent
Sensor
: PHR-5 (J.S.T.) or equivalent
Board side : B5B-PH-K-S (J.S.T.) or equivalent
6
FTP-624MCL303/304/FTP-624DSL113
3. Cutter
Mech side : EHR-4 (J.S.T.) or equivalent
Board side : B4B-EH (J.S.T.) or equivalent
■ FUNCTION
Item
Item
1.
2.
3.
4.
Test print function
8.
9.
Cutter abnormality detection
Motor power saving function
Paper out detection
Paper near end detection
Head up detection
10. Mark detection function
11. MCU operation abnormality detection
Thermal head temperature abnormality
detection
5.
12. Power ON/OFF sequence protection
6.
7.
Blow-out fuse detection
13. Motor over-current protection
14. Hardware timer
Head voltage abnormality detection
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
Fujitsu Component Limited
Gotanda-Chuo Building
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Fujitsu Components
International
Headquarter
Offices
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 06/2002
7
|