Compact Power Relay
1 Pole—25A for Automotive Applications
RoHS compliant
FTR-G1 Series
n
FEATURES
l Compact for high density packaging (70% volumne of previ-
ous generation FTR-P3 series)
l High contact capacity with proven contact material (min.
100,000 operations, 14V, 25A achived, even with reduced
size)
l Coil power savings (640mW nominal achived with state-of-
the-art magnetic analysis/design)
l Ease of PCB layout (all terminals on perimeter, coil and con-
tact terminals separated)
l Lower noise (57dB average at 5cm)
l RoHS compliant since begining of production.
Please see page 7 for more information
n ORDERING INFORMATION
FTR-G1
C
N
010 W1
[Example]
(a)
(b) (c) (d) (e)
(a)
(b)
Series Name
Contact Arrangement
FTR-G1: FTR-G1 Series
C
: 1Form C
(c)
(d)
Contact Gap
N
: 0.3mm gap
Nominal Coil Voltage
009
010
012
: 09 VDC
: 010 VDC
: 012 VDC
(e)
(f)
Contact Material
W1
: Silver-tin oxide-indium
Custom Designation
To be assigned custom designation
Note: The designation name is stamped on the top of the relay case as follows:
Example: Ordering part number: FTR-G1CN010W1
Stamped on part number: G1CN010W1
n TYPICAL APPLICATIONS
l
l
l
Power window
l
Power seat
l
l
Tilt steering
Door lock
l
Wiper/IWW
Retractable antenna
Sun roof
1
FTR-G1 SERIES
n INSULATION
Item
Specification
Resistance
Minimum 100 MΩ 1 min.
500 VAC (50/60 Hz) 1 min.
500 VAC (50/60 Hz) 1 min.
Dielectric
Strength
open contacts
coil and contacts
n REFERENCE DATA
Operate/release voltage distribution
Contact resistance distribution
Contact current
100
10000
1000
100
100
FTR-G1CN012W1
Data: FTR-G1CN010W1
Units: n=100
Data: FTR-G1CN010W1
Units: n=100
80
60
40
20
0
80
25°C
60
Operate
Release
85°C
40
20
0
Failure mode:
Make contact open by short coil
10
0
10
20
30
40
50
60
70
0
10 20 30 40 50 60 70 80
0
10 20 30 40 50 60 70 80
Contact current (A)
Ratio to rated voltage (%)
Contact resistance (mΩ)
Ambient temperature vs voltage
Coil temperature rise
Coil temperature rise
1000
500
100
90
80
70
60
50
40
30
20
10
0
Coil voltage: 16VDC max.
0A
16
15
14
13
12
11
10
9
FTR-G1CN012W1 (25°C)
FTR-G1CN012W1
0.64W
FTR-G1CN012W1
10A
at : 25°C
25A
20A
Allowable voltage
100
50
10A
0A
no current
8
7
6
5
4
3
10
0.1
2
1
10
1
0
10
20
30
Coil power (W)
Applied time (m)
0
-40 -20
0
20
40
60
80 100
Ambient temperature (°C)
Vibration
Impact
1000
100
10
FTR-G1CN012W1
10 pieces
1000
FTR-G1CN012W1
10 pieces
Chattering more than 1 m sec.
(coil de-energized, Y direction)
800
600
400
200
0
Make (coil energized)
Break (coil de-energized)
2
44 m/s
Printed
face
Printed
face
Automotive
standard
Y
Y
Z'
X'
X
Z
Y'
2
1
Time: 11±1ms. half sign curve
Detection chattering more than 1 msec.
Coil voltage: rated voltage or 0V
1
10
100
1000
10000
Frequency (Hz)
X
X’
Y
Y'
Z
Z'
Direction
3
FTR-G1 SERIES
n DIMENSIONS
Schematic
+
13.7 0.5
-
G1CN012WI
0635F N1
F&T
JAPAN
Mounting hole layout
(bottom view)
Schematic
(1.00)
Type
(example)
Marking (example)
G1CN012W1
Lot No. (weekly code)
0612A
Manufacturer
Japan
Manufacture
country
Tube
375 1
0.2
17.9
Unit: mm
4
FTR-G1 SERIES
RoHS Compliance and Lead Free Relay Information
1. General Information
l
Relays produced after the specific date code that is indicated on each data sheet are lead-free
now. All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info.
(http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf)
Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu.
All signal and power relays also comply with RoHS. Please refer to individual data
sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that
are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE).
It has been verified that using lead-free relays in leaded assembly process will not cause any
problems (compatible).
l
l
l
l
l
l
“LF” is marked on each outer and inner carton. (No marking on individual relays).
To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office.
We will ship leaded relays as long as the leaded relay inventory exists.
Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC)
2. Recommended Lead Free Solder Profile
l
Recommended solder paste Sn-3.0Ag-0.5Cu.
Flow Solder condition:
Pre-heating:
Soldering:
maximum 120˚C
dip within 5 sec. at
260˚C soler bath
Solder by Soldering Iron:
Soldering Iron
Temperature: maximum 360˚C
Duration:
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3. Moisture Sensitivity
l
Moisture Sensitivity Level standard is not applicable to electromechanical realys.
4. Tin Whisker
l
Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in
house test.
5
FTR-G1 SERIES
Fujitsu Components International Headquarter Offices
Japan
Europe
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (81-3) 5449-7010
Tel: (31-23) 5560910
Fax: (81-3) 5449-2626
Fax: (31-23) 5560950
Email: [email protected]
Email: [email protected]
North and South America
Asia Pacific
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Fax: (1-408) 745-4970
Tel: (65) 6375-8560
Email: [email protected]
Fax: (65) 6273-3021
Email: [email protected]
©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property off their respective
owners.
Fujitsu Components America does not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu
Components America, Inc. reserves the right to change specifications/datasheets without prior notice. Rev. January 25, 2008.
6
|