Fujitsu Crib FPCCR05 User Manual

F u j i t s u C o m p u t e r S y s t e m s  
Charge-Only Cradle  
User’s Guide  
FPCCR05  
I N S T R U C T I O N S  
The charge-only cradle is designed for a desktop, counter  
top, or wall-mounted installation where a quick connection  
to a DC power source is needed. The Tablet PC can be  
placed in the charge-only cradle and used while external DC  
power is supplied to the cradle. The connector pins on the  
cradle are “high-usage” type pins and are designed to with-  
stand a large number of insertions and removals. The cradle  
includes two adapters that fit over the Tablet PC’s DC-in  
port to make it more suitable for the high-usage environ-  
ment.  
The cradle can accommodate a Tablet PC with a standard  
main battery or an optional high-capacity battery. A remov-  
able spacer is included with the cradle to make the cradle  
usable with either battery.  
 
Verifying Battery Size  
Determine whether your Tablet PC has a standard main  
battery or an optional high-capacity main battery installed.  
If your Tablet PC has a high-capacity main battery  
installed, remove the spacer (Figure 2) that is located  
inside the cradle on the right. Pull it upwards to  
remove it from the slot.  
Stow the spacer in the spacer tray inside the charge-  
only cradle so that it will be available for occasions in  
which you use the standard battery. To remove the  
spacer from the tray, press down on the right side of the  
spacer, causing its left side to lift up.  
If your Tablet PC has a standard main battery installed,  
be sure the spacer is installed in the slot on the inside  
right of the cradle (Figure 2).  
Spacer  
Slot  
Spacer Tray  
Figure 2. Inside the Charge-Only Cradle  
3
 
Installing the Tablet PC in the Charge-Only Cradle  
1. Place the cradle on the flat, stable location in which it  
will be used.  
2. After verifying that the spacer is configured correctly  
and the DC adapter is attached to the DC-in port, hold  
the system in landscape mode, with the buttons  
arranged across the top (Figure 3).  
Figure 3. Installing the Tablet PC in the Cradle  
3. Insert the tablet into the cradle until it rests securely on  
the bottom of the cradle.  
4. Plug the system AC adapter into the DC-in port on the  
right side of the cradle, and the other end into a power  
outlet.  
4
 
DC-In Port  
Figure 4. DC-In Port on Cradle  
Removing the Tablet PC from the Charge-Only Cradle  
While holding the base of the cradle with one hand, gently  
pull the Tablet PC out of the cradle.  
Mounting the Cradle on a Wall  
The charge-only cradle is designed so that it can be easily  
mounted to a wall. The cradle consists of two large compo-  
nents: a base and a cradle. Before mounting the cradle to a  
wall, the base component must be removed.  
To separate the two components, perform the following  
steps:  
1. Holding the cradle portion with one hand and the base  
portion with the other, lift the cradle section while  
pushing down on the base section until the two halves  
disengage at the separation point (Figure 5).  
5
 
Cradle Section  
Separation Point  
Base  
Section  
Figure 5. Separating the Cradle  
2. Once disengaged, store the base section in a safe place  
for future use.  
3. The back of the cradle section has four holes for wall-  
mounting and six holes for reattaching the base section.  
Wall-mount Holes  
Base Attachment Holes (6 total)  
Figure 6. Wall-Mount holes  
6
 
4. Attach four screws (sheet metal, #14 panhead, zinc-  
plated recommended, or equivalent) to the wall as  
shown in Figure 7. The screw heads should extend from  
the wall approximately 0.25.  
12.25" (311.0 mm)  
4.26" (108.0 mm)  
Figure 7. Wall-mount Screw Dimensions  
5. Align the wall-mount holes on the cradle (Figure 6)  
with the mounting screws so that the screw heads  
extend into the round portions of the wall-mount  
holes. (Figure 8)  
Slotted portion  
Round portion  
Figure 8. Wall-mount Hole  
6. When the four screw heads are aligned, press the cradle  
firmly against the wall and slide it to the right and  
downwards, so that the screws move to the top of the  
slotted portion of the holes, locking it in place.  
7
 
Fujitsu Computer Systems Corporation  
1250 E. Arques Avenue (M/S 122)  
Sunnyvale, CA 94085  
For more information, visit our Web site  
at: us.fujitsu.com/computers  
For technical support call:  
1-800-8Fujitsu (1-800-838-5487)  
or e-mail us at: [email protected]  
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu, Ltd. All other trademarks  
mentioned herein are the property of their respective owners. We cannot guarantee the  
accuracy of the contents of this document. We disclaim liability for errors, omissions or  
future changes.  
© 2004 Fujitsu Computer Systems Corporation. All rights reserved.  
FPC58-1087-01  
8
 

Echo Brush Cutter SRM 2110 User Manual
Escort Radar Detector S2 User Manual
Fellowes Paper Shredder c120ci User Manual
First Alert Smoke Alarm SA511CN2 3ST User Manual
Fisher Price Baby Toy B9760 User Manual
Fisher Price Doll 73397 User Manual
Fostex Microcassette Recorder X 77 User Manual
Fostex Recording Equipment XR 3 User Manual
Gateway Computer Monitor 22 INCH WIDESCREEN LCD MONITOR User Manual
Genelec Speaker 1092A User Manual