Frigidaire Dehumidifier D25D User Manual

Dehumidifier  
D25D, D50D, D70D  
Models  
D25D Volts: 115/60Hz Capacity: 25 Pints Moisture Removal: 25 Pint/Day  
D50D Volts: 115/60Hz Capacity: 50 Pints Moisture Removal: 50 Pint/Day  
D70D  
Volts: 115/60Hz Capacity: 70 Pints Moisture Removal: 70 Pint/Day  
920-198-10 (3-10)  
 
920-198-10  
DESCRIPTIONOFCOMPONENTS  
DEHUMIDIFIED  
DRY AIR VENT  
Figure 1  
CONTROL PANEL  
AIR FILTER  
HANDLE  
MOIST AIR  
INTAKE  
DRAIN PUMP OUTLET  
(ONLY ON 50 AND 70 PINT MODELS)  
CONTINUOUS  
DRAINAGE OUTLET  
DRAIN BUCKET  
ROLL CASTERS  
FRD001  
FUNCTIONEXPLANATION  
Figure 2  
BUCKET FULL LAMP DEFROST LAMP  
CURRENT TEMP / TIMER SET DISPLAY  
LAMP LIGHTS WHEN LAMP LIGHTS WHEN UNIT IS  
WHEN THE UNIT IS RUNNING THE CURRENT TEMP IS DISPLAYED.  
WHEN THE TIMER BUTTON IS PRESSED THIS WINDOW DISPLAYS  
THE TIMER SETTING THEN REVERTS BACK TO THE TEMPERATURE  
AFTER 10 SECONDS.  
DRAIN BUCKET IS  
FULL AND NEEDS TO  
BE EMPTIED.  
DEFROSTING (SEE PAGE 5).  
°C/°F SELECTOR  
PRESS THE °C/°F  
SWITCH BUTTONS  
IT WILL SWITCH  
TIMERS  
CURRENT HUMIDITY DISPLAY  
FAN SPEED  
HIGH/LOW  
WHEN THE UNIT IS ON PRESS THE DISPLAYS THE CURRENT  
TIMER BUTTON TO DISPLAY THE  
POWER OFF TIMER.  
RELATIVE HUMIDITY (RH) IN  
THE ROOM. WHEN THE  
IS PRESSED THE HUMIDITY  
SETTING IS DISPLAYED.  
OR  
POWER  
ON/OFF  
BETWEEN °C AND °F.  
SELECT FROM 1-24 HOURS OF  
RUNNING TIME UNTIL THE UNIT  
SHUTS OFF AUTOMATICALLY.  
WHEN THE UNIT IS OFF PRESS THE  
TIMER BUTTON TO DISPLAY THE  
POWER ON TIMER. SELECT FROM  
1-24 HOURS UNTIL THE UNIT WILL  
TURN ON AUTOMATICALLY.  
SET HUMIDITY  
ADJUST THE HUMIDITY % FROM  
30% TO 90% RH BY PRESSING THE  
BUTTONS. HUMIDITY IS  
ADJUSTED IN 5% INCREMENTS.  
OR  
FRD002  
3
 
920-198-10  
OPERATIONINSTRUCTIONS  
INSTALLATIONINSTRUCTIONS  
Follow the steps below for unpacking and set up your unit.  
WARNING  
STEP 1.  
STEP 2.  
STEP 3.  
Remove unit from carton and inspect.  
Remove accessories from drain bucket.  
Electrical Hazards  
Install Roll Casters (D25D models only) per installation  
instructions below.  
STEP 4.  
Set up unit in position with adequate clearance. Installation  
of unit is complete.  
Do not fold power cord as shown at left.  
Roll Caster Installation (D25D Models only)  
STEP 1.  
STEP 2.  
STEP 3.  
Locate Roll Casters removed during STEP 2 above.  
Lay unit on its side for ease of installation.  
Insert Roll Casters in slots as shown (See Figure 3) until they  
click into place.  
Make sure the plug is placed fully and  
firmly into the receptacle.  
Figure 3  
ROLL CASTER  
Do not use multiple sockets as shown at  
left.  
Make sure the plug is clean.  
FRD031  
Set the unit upright. Roll Caster installation is complete.  
Allow unit to sit upright 1 hour before operating.  
STEP 4.  
STEP 5.  
After turning the unit off please take plug  
out of the receptacle.  
Allow 8 inches of space on all sides of the unit.  
Figure 4  
Do not have wet hands when connecting  
the power plug.  
8’’  
Do not pull the power cord to avoid a  
broken cord, which can lead to danger.  
8’’  
8’’  
8’’  
FRD032  
4
 
920-198-10  
Start Operation  
When Bucket Full Lamp Is On  
STEP 1.  
Place the unit in an upright position on a flat, steady, stable and  
When the drain bucket is full, the Bucket Full lamp will illuminate and the  
unit will stop operating. The drain bucket should be carefully removed from  
the unit by sliding it outwards (See Figure 6) and should be emptied. Then  
place the empty drain bucket back to its proper position, (See Figure 7)  
the unit will start operating and run normally.  
heat resistant surface. Make sure there is nothing flammable  
or heat sensitive within 39 inches. Operating the product in  
any other position could cause a hazard.  
Figure 6  
WARNING  
Electrical Shock Hazard  
Make sure your electrical receptacle has the  
same configuration as your dehumidifier’s  
plug. If different, consult a Licensed Electrician.  
Do not use plug adapters.  
Do not use an extension cord.  
Do not remove ground prong.  
Always plug into a grounded 3 prong oulet.  
Failure to follow these instructions can result in  
death, fire, or electrical shock.  
PLEASE USE BOTH HANDS  
TO CAREFULLY EMPTY THE  
DRAIN BUCKET.  
FRD005  
STEP 2.  
STEP 3.  
Insert the plug into a suitable wall  
socket. The dehumidifier is suitable  
for operation on an electricity supply  
having the same voltage as that  
shown on its rating label.  
Defrost  
When the unit is operated in low temperatures (less than 54 °F  
the surface of the evaporator will accumulate a layer of frost which will  
reduce the efficiency of the dehumidifier. When this happens the unit will go  
into periodic defrost mode automatically. The Defrost Lamp will illuminate  
on control panel, this is quite normal (See Figure 7).  
Make sure the Drain Bucket is correctly placed in the proper  
position (See Figure 5). (After switching the unit 'ON" for the  
first time, if the Bucket Full lamp illuminates, just pull out  
the drain bucket; check to ensure that the float lever is able  
to move freely, then return the drain bucket to the correct  
position).  
The dehumidifier will operate in temperatures down to 41 °F. The time it  
takes to defrost may vary. If the unit freezes up it should be turned off at the  
power supply for a few hours and then re-started. If the room temperature  
remains below 41 °F the unit should be switched off. It is not recommended  
to use the dehumidifier in temperatures below 41 °F.  
Figure 5  
Figure 7  
DEFROST LAMP  
BUCKET FULL LAMP  
DRAIN BUCKET  
DRAIN BUCKET  
FRD004  
FRD006  
5
 
920-198-10  
Do not use insect, oil or paint spray around the unit (See Figure 11), it might  
cause damage to the plastic parts or start a fire.  
OPERATINGDO'SANDDON'TS  
Do not place anything on top of the unit or control panel (See Figure 8).  
Figure 11  
Figure 8  
FRD014  
Do not place the unit on an uneven surface (See Figure 12), to avoid  
shaking, noise and leakage of water.  
FRD007  
Figure 12  
Do not place anything over the inlet or outlet points (See Figure 9).  
Figure 9  
FRD015  
Do always keep the unit 8 in. away from the wall (See Figure 13) to dissipate  
the heat properly.  
Figure 13  
FRD008  
Do not wet the unit or the control panel (See Figure 10).  
8.00 IN.  
Figure 10  
FRD010  
FRD016  
6
 
920-198-10  
Do not put any foreign objects into the unit, it is dangerous and will result  
in damage to the unit (See Figure 14).  
When moving or putting unit in storage, do not place the unit on its side or  
upside down and avoid violent shaking (See Figure 16).  
Figure 16  
Figure 14  
FRD020  
Do ask professional service technicians to service the unit as required  
(See Figure 17).  
Figure 17  
FRD017  
Do close all open windows to reach the maximum possible efficiency of  
dehumidifier removing moisture (See Figure 15).  
Figure 15  
FRD012  
FRD018  
7
 
920-198-10  
Insert the drain hose through the hole of the drain cover. Then connect the  
drain hose to the drain port (See Figure 20).  
CONTINUOUSDRAINAGE  
To save having to periodically empty the drain bucket, this unit can be  
configured for continuous drainage. You can use the supplied drain hose  
to connect to the continuous drainage connector (See Figure 18).  
Figure 20  
BACK OF UNIT  
Figure 18  
BACK OF UNIT  
DRAIN HOSE  
DRAIN HOSE  
DRAIN COVER  
FRD023  
DRAIN COVER  
Tighten the drain cover in clockwise direction onto the rear of the unit  
(See Figure 21).  
FRD021  
Unscrew and remove the drain cover at the rear of the unit (See Figure 19).  
Figure 21  
Remove the soft rubber stopper. Put it into the drain bucket for safe keeping  
(See Figure 19).  
BACK OF UNIT  
Figure 19  
BACK OF UNIT  
DRAIN COVER  
DRAIN HOSE  
SOFT RUBBER STOPPER  
DRAIN COVER  
FRD024  
Place the bucket in its original location (See Figure 22).  
Figure 22  
FRD022  
PUSH THE DRAIN BUCKET  
BACK INTO THE UNIT IN THE  
DIRECTION THE ARROW IS  
POINTING.  
DRAIN  
BUCKET  
DRAIN HOSE  
FRD025  
8
 
920-198-10  
Drain Hose Routings  
Continuous Draining using the Pump  
(D50D/D70D models only)  
Installation:  
When using the function of continuous drainage, the drain hose must be  
placed horizontally below the drainage hole (See Figure 23).  
You must avoid uneven ground and folding the hose (See Figure 23).  
STEP 1.  
STEP 2.  
STEP 3.  
Connect the attached continuous drainage adaptor (1) to the  
drain hole on the rear panel (2).  
Figure 23  
Connect the supplied water hose to the plug that fits into the  
drain hole.  
Lead the other end to a suitable location for drainage, like a  
drain or sink and insert the plug into the water drain.  
The maximum distance and the rise may be 15 ft from the unit. Exceeding  
this distance may damage the unit or cause leaks. When the unit’s drain  
bucket capacity reaches a certain water level, it will drain automatically  
(See Figure 24).  
Dismantle:  
Press the drain hole (3) on the unit rear panel. The automatic drainage  
adaptor will pull out (See Figure 24).  
Figure 24  
3
1
2
SUPPLIED  
WATER  
HOSE  
PLUG  
FRD027  
NOTICE  
In the automatic mode, the condensed moisture  
is always removed through the air exhaust hose.  
Removing the rubber plug from the water drain  
will allow the water to drain out at this point. The  
water drain can not be used.  
FRD026  
9
 
920-198-10  
Cleaning Steps  
MAINTENANCE  
STEP 1.  
Pull the air filter out gently (See Figure 25).  
WARNING  
Figure 25  
Electrical Shock Hazard  
AIR FILTER  
Make sure your electrical receptacle has the  
same configuration as your dehumidifier’s  
plug. If different, consult a Licensed Electrician.  
Do not use plug adapters.  
Do not use an extension cord.  
Do not remove ground prong.  
Always plug into a grounded 3 prong oulet.  
Failure to follow these instructions can result in  
death, fire, or electrical shock.  
For safety reasons, make sure the unit is  
unplugged before servicing or cleaning.  
FRD029  
STEP 2.  
Clean the air filter with a vacuum cleaner or wash it with clean  
water and dry with a dry cloth (See Figure 26).  
Cleaning the shell  
Figure 26  
STEP 1.  
STEP 2.  
Wipe the shell with a clean, soft cloth.  
If the unit is very dirty, use mild detergent then wipe off the  
detergent with half dried cloth.  
WARNING  
Water Hazard  
Do not wash the unit with a hose  
or immerse it in water. This may  
cause leakage of electricity or a  
shock hazard.  
FRD030  
Cleaning the air filter  
STEP 3.  
Put the clean air filter back in place and continue to operate  
the dehumidifier.  
The purpose of the air filter is to filter dust and other materials from the  
air. If the filter is blocked by dust the electricity usage will be greater than  
normal. For optimal moisture removal and efficiency, clean the filter every  
two weeks.  
10  
 
920-198-10  
INCASEOFEMERGENCY  
If a problem occurs, unplug the unit and contact a qualified servicing center  
immediately. Do not disassemble the unit yourself.  
NOTICE  
If the power cord on this unit is damaged it must  
be replaced by the manufacturer, its service agent  
or qualified service technician in order to avoid a  
hazard.  
NOTICE  
This appliance is not intended for use by childern  
or other persons without assistance or supervision  
if their physical, sensory or mental capabilities  
prevent them from using it safely. Children should  
be supervised to ensure that they do not play with  
the appliance.  
11  
 
920-198-10  
Friedrich Air Conditioning Company  
P.O. Box 1540  
San Antonio, TX 78295  
210.357.4400  
DEHUMIDIFIERS  
LIMITED WARRANTY  
FIRSTYEAR  
ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from  
date of original purchase, FRIEDRICH will repair the product at no charge, provided the product is transported to a Friedrich  
Authorized Service Center for repair. ALL transportation charges are the sole responsibility of the owner. This remedy is expressly  
agreed to be the exclusive remedy within twelve months from the date of the original purchase.  
SECOND THROUGH FIFTH YEAR  
SEALED REFRIGERANT SYSTEM: If the Sealed Refrigeration System (defined for this purpose as the compressor, condenser  
coil, dehumidifying coil, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in your dehumidifier fails  
because of a defect in workmanship or material within sixty months from date of purchase, FRIEDRICH will pay a labor allowance  
and parts necessary to repair the Sealed Refrigeration System; PROVIDED FRIEDRICH will not pay the cost of diagnosis of the  
problem, removal, freight charges, and transportation of the dehumidifier to and from the Service Agency, and the reinstallation  
charges associated with repair of the Sealed Refrigeration System. All such cost will be the sole responsibility of the owner. This  
remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase.  
APPLICABILITY AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A.,  
District of Columbia, and Canada. This warranty is not applicable to:  
1. Air filters or fuses.  
2. Products on which the model and serial numbers have been removed.  
3. Products which have defects or damage which results from improper installation, wiring, electrical current  
characteristics, or maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication  
of the product and/or units installed in a corrosive atmosphere, default or delay in performance caused by war,  
government restrictions or restraints, strikes, material shortages beyond the control of FRIEDRICH, or acts of God.  
OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service  
Organization in your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty performance, write  
to: Room Air Conditioner Service Manager, Friedrich Air Conditioning Co., P.O. Box 1540, San Antonio, TX 78295-1540.  
LIMITATIONS: THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty  
notwithstanding, ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY  
SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND  
EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR  
IMPLIED WARRANTY.  
NOTE: Some states do not allow limitations on how long an implied warranty lasts, or do not allow the  
limitation or exclusion of consequential or incidental damages, so the foregoing exclusions and limitations  
may not apply to you.  
OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
PROOF OF PURCHASE: Owner must provide proof of purchase in order to receive any warranty related services.  
All service calls for explaining the operation of this product will be the sole responsibility of the consumer.  
All warranty service must be provided by an Authorized FRIEDRICH Service Agency, unless authorized  
by FRIEDRICH prior to repairs being made.  
(2-10)  
12  
 
920-198-10  
Friedrich Air Conditioning Co.  
Post Office Box 1540 • San Antonio, Texas 78295-1540  
4200 N. Pan Am Expressway • San Antonio, Texas 78218-5212  
(210) 357-4400 • FAX (210) 357-4480  
Printed in the U.S.A.  
13  
 

Earthquake Sound Speaker HoLeeS 12 User Manual
Faber Ventilation Hood 630006369 User Manual
Fagor America Electric Pressure Cooker uCOOK PRESSURE COOKER SET User Manual
Ferris Industries Lawn Mower 1000ZKAV21 48 User Manual
Fiat Automobile 11 User Manual
Fisher Price Child Tracker K7376 User Manual
FujiFilm Digital Camera S2 Pro User Manual
Fujitsu Network Card FMW43SA1 User Manual
Gamber Johnson Laptop Docking Station GD8000 User Manual
GE Water Dispenser GNSV70FBL User Manual