First Alert Home Security System FA148CP User Manual

FA168CPS / FA168CPSSIA

FA148CP / FA148CPSIA

Security Systems

Programming Guide

READ

ARM

A260

READ

OFF

AWA

A560

K5305-5PRV5 11/08 Rev. B

PROGRAMMING MODE COMMANDS

TO ENTER PROGRAMMING MODE (using an alpha keypad connected to the control):

A. POWER UP, then press [ ] and [#] at the same time, within 50 seconds of powering up (this method must be used if 98

was used to exit program mode). OR

✱

B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.

PROGRAMMING COMMANDS

Task

Command/Explanation

Go to a Data Field

Entering Data

Press [∗] + [Field Number], followed by the required entry.

When the desired field number appears, simply make the required entry. When the last entry

for a field is entered, the keypad beeps three times and automatically displays the next data

field in sequence. If the number of digits that you need to enter in a data field is less than the

maximum digits available (for example, the phone number fields *41, *42), enter the desired

data, then press [∗ ] to end the entry. The next data field number is displayed.

Press [#] + [Field Number].

Review a Data Field

Data will be displayed for that field number. No changes will be accepted in this mode.

Deleting an Entry

Press [∗] + [Field Number] + [∗]. (Applies only to fields ∗40 thru *46, *94, and pager fields)

Press ∗96. Initializes download ID and subscriber account number.

Press ∗97. Sets all data fields to original factory default values.

Press ∗56. Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800

RF transmitters.

Initialize Download ID

Reset Factory Defaults

Zone Programming

Function Key Programming

Zone Programming

(Expert Mode)

Press ∗57. Unlabeled keypad keys (known as ABCD keys) for special functions

Press ∗58. Same options as *56 mode, but with fewer prompts. Intended for those familiar

with this type of programming, otherwise *56 mode is recommended.

Output Device Mapping

Output Programming

Zone List Programming

Alpha Programming

IP/GSM Programming

Exit Program Mode with

installer code lockout

Press ∗79. Assign module addresses and map individual relays/powerline carrier devices

Press ∗80. 4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers

Press ∗81. Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.

Press ∗82. Zone alpha descriptors

Press ∗29. For programming the IP/GSM options.

Press ∗98. Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0.

To reenter programming mode, the system must be powered down, then powered up. Then

use method A above. See field *88 for other *98 Program mode lockout options.

Exit Program Mode

Press ∗99. Exits program mode and allows re-entry by: Installer Code + 8 + 0 + 0 or method A

above.

Enter code + [#] +64. Create schedules to automate various system functions.

Installer code + [#] + 1 (perform while system is disarmed and in normal mode)

Scheduling Mode

Site-Initiated Download

AVS QUICK PROGRAMMING COMMANDS (for AAV sessions using the AVS system)

For controls with the following firmware revision levels, these commands automatically configure the control for AVS

operation. FA148CP = version 6.0 or higher; FA168CPS = version 7.0 or higher

• installer code + [#] + 03: enable AVS operation

• installer code + [#] + 04: enable AVS operation and enable panels sounds on the AVST speaker

• installer code + [#] + 05: remove all programming options that were set if [#] + 03 quick command was performed

• installer code + [#] + 06: remove all programming options that were set if [#] + 04 quick command was performed

Refer to the AVS SYSTEM ENABLE and QUICK PROGRAMMING COMMANDS section for details on the specific options

that are set with each command, depending on the control used.

To select the AAV session communication path (phone line/communication device), see field ∗55 Dynamic Signaling Priority.

To enable AAV operation, use ∗91 Options field (option 4).

Special Messages

OC = OPEN CIRCUIT (no communication between Keypad and Control).

EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).

After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.

This will revert to a “Ready” message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this

delay by pressing [#] + [0].

If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after

you correct the programming.

IMPORTANT: The Real-Time Clock must be set before the end of the installation. See procedure in the Setting

the Real-Time Clock section of this manual.

– 3 –

DATA FIELD PROGRAMMING FORM

FA148CP/FA148CPSIA

only to

controls, except entries shown in dashed boxes, which apply

Entries apply to the FA168CPS/FA168CPSSIA and

the FA168CPS (partition entries) and are not applicable to the FA148CP/FA148CPSIA controls

/FA168CPSSIA

SIA-Compliant Controls: Where noted, certain fields have special settings when used with the FA168CPSSIA and FA148CPSIA SIA-Compliant

controls (indicated by in reverse type and heavy borders for easy identification).

SIA-Compliant Controls

Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.

SIA Guidelines for Non-SIA-Compliant Controls: Notes in certain fields give instructions for programming the FA168CPS/FA148CP for False

Alarm Reduction (these controls can be programmed to reduce false alarms, but they are not fully SIA compliant).

✱

SYSTEM SETUP ( 20– 29)

Installer Code

∗20

[4112]

Enter 4 digits, 0-9

The Installer Code is used to assign the 4-digit Master Security Code.

The Installer Code can perform all system functions except it cannot

disarm the system unless it was used to arm the system.

Quick Arm Enable

∗21

[0,0]

0 = no

Part. 1

Part.2

1 = yes

If enabled, users can press the [#] followed by an arming key to arm

the system instead of using a security code. The security code is

always needed to disarm the system.

RF Jam Option

0 = no RF Jam detection

1 = send RF Jam report

∗22

[0]

If enabled, a report is sent if the system detects an RF jamming signal.

UL: must be 1 if wireless devices are used

Quick (Forced) Bypass

∗23

[0,0]

0 = no quick bypass

Part. 1

Part. 2

1 = allow quick bypass (code + [6] + [#] )

Zones bypassed by this function will be displayed after the bypass is

initiated.

UL: must be 0

RF House ID Code

∗24

∗26

[00,00,00]

00 = disable all wireless keypad use

01–31 = using 5827, 5827BD or

5804BD keypad

Common

The House ID identifies receivers and wireless keypads. If a 5827 or

5827BD Wireless Keypad or 5804BD Transmitter is being used, a

House ID code must be entered and the keypad set to the same

House ID. You can assign RF house ID for each partition

Chime By Zone

[0]

0 = no (chimes on fault of any entry/exit

or perimeter zone when chime

mode on)

If “yes,” list chime zones on zone list 3 using *81 Menu mode.

If enabled, you can define the specific zones intended to chime when

faulted while the system is in Chime mode.

1 = yes (chimes on fault of specific

zones listed in chime zone list 3

when Chime mode on)

Powerline Carrier Device (X–10)

House Code

∗27

∗28

[0]

Powerline Carrier devices require a House ID, identified in this field.

Program Powerline Carrier devices in interactive modes ∗79, ∗80 and

0 = A

1 = B

2 = C

3 = D

4 = E

5 = F

6 = G

7 = H

8 = I

#11 = L

#12 = M

#13 = N

#14 = O

#15 = P

∗81.

UL: not for fire or UL installations

9 = J

#10 = K

Access Code For Phone Module

00 = disable

1st digit: enter 1–9

2nd digit: enter # + 11 for "∗", or # + 12

for "#".

[00]

(Partition 1 only)

You must assign a 2-digit access code for the 4286 Phone Module, if

used. Example: If desired access code is 7∗, then 7 is the first entry,

and [#] + 11 (for ∗) is the second entry.

NOTE: A 0 in either digit disables the phone module.

UL: must be 00 for UL Commercial Burg. installations

∗29 Enable IP/GSM – Communication Device Menu Mode (pass-through programming)

This is a Menu Mode command, not a data field, for programming IP/GSM communication device options. See ∗29 Menu

Mode section later in this document.

– 4 –

Single Alarm Sounding Per Zone

0 = unlimited sounding

1 = one alarm sounding per zone

∗31

[0]

If enabled, limits alarm sounding on the bell output to once per zone

per armed period.

SIA-Compliant Controls: If “0”

selected, “alarm sounding per zone”

will be the same as the “number of

reports in armed period” set in field

*93 (1 if one report, 2 if 2 reports,

unlimited for zones in zone list 7).

Fire Alarm Sounder Timeout

0 = sound stops at timeout selected in

field ∗33

∗32

∗33

∗34

[0]

This control complies with NFPA requirements for temporal pulse

sounding of fire notification appliances. Temporal pulse sounding for a

fire alarm consists of the following: 3 pulses – pause – 3 pulses – pause – 3

pulses.

1 = no timeout; sounds until manually

turned off

UL: must be 1 for fire installations

Alarm Sounder (Bell) Timeout

[1]

0 = none

1 = 4 min

2 = 8 min

3 =12 min

4 = 16 min

This field determines whether the external sounder will shut off after

time allotted, or continue until manually turned off.

UL: For residential fire alarm installation, must be set for a minimum of 4 min

(option 1); for UL Commercial Burglary installations, must be minimum 16 min

(option 4)

Exit Delay

00 - 96 = 0 - 96 secs

97 = 120 secs

[60,60]

Part. 1

Part. 2

The system waits the time entered before arming entry/exit zones. If

the entry/exit door is left open after this time expires, an alarm will

occur. Common zones use same delay as partition 1.

SIA Guidelines: minimum exit delay is 45 seconds

Common zones use part. 1 delay.

UL installations: For UL Commercial Burglar Alarm and UL Residential Burglar

Alarm installations with line security, total exit time must not exceed 60

seconds.

SIA-Compliant Controls:

45 - 96 = 45 - 96 secs; 97 = 120 secs

NOTE: Entries less than 45 will result

in a 45-second delay.

Entry Delay #1

00 - 96 = 0 - 96 seconds

97 = 120 secs

98 = 180 secs

99 = 240 secs

∗35

[30,30]

Part. 1

Part. 2

Upon entering, the system must be disarmed before the time entered

expires, otherwise it sounds an alarm.

Common zones use same delay as part 1.

SIA Guidelines: minimum entry delay is 30 seconds

SIA-Compliant Controls:

For UL Residential Burglary Alarm installations, must be set for a maximum of

30 seconds; entry delay plus dial delay should not exceed 1 min. For UL

Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.

Upon entering, the system must be disarmed before the time entered expires,

otherwise it sounds an alarm.

30-96 = 30 - 96 secs; 97 = 120 secs;

98 = 180 secs; 99 = 240 secs

NOTE: Entries less than 30 will result

in a 30-second delay.

Entry Delay #2

∗36

∗37

[30,30]

See *35 Entry Delay 1 for entries.

Part. 1

Part. 2

Audible Exit Warning

0 = no; 1 = yes

[1,1]

Part. 1

Part. 2

Warning sound consists of slow continuous beeps until the last 10

seconds, and then it changes to fast beeps. Sound ends when exit time

expires.

SIA-Compliant Controls: Feature

always enabled; field does not exist.

SIA Guidelines: must be enabled

Confirmation Of Arming Ding

0 = no

1 = yes (wired keypads and RF)

2 = yes, RF only (except 5827,

5827BD)

∗38

[0,0]

Part. 1

Part. 2

Confirmation of arming is 1/2-sec external sounder “ding.”

If 1 selected, ding occurs when closing report is sent if open/close

reporting is enabled, or at the end of Exit Delay. If 2 selected, ding

occurs upon reception of the wireless arming command.

UL: must be 1 for UL Commercial Burglar Alarm inst.

– 5 –

When the system powers up armed, an alarm will occur 1 minute after

arming if a zone is faulted. Note that if the previous state was armed

Away or Stay, the system ignores sensor changes for 1 minute, which

allows sensors such as PIRs to stabilize.

UL: must be 1

SIA Guidelines: must be 1

Power Up In Previous State

0 = no, always power up disarmed;

1 = yes, power up in previous state

∗39

SIA-Compliant Controls: Feature

always enabled; field does not exist.

✱

DIALER PROGRAMMING ( 40 – 42)

PABX Access Code or Call

Waiting Disable

Enter up to 6 digits.

∗40

Call Waiting: If the subscriber’s phone service has “call waiting” (and

is not using PABX), enter “*70” (“# + 11”) plus “# + 13” (pause) as the

PABX entry to disable “call waiting” during control panel calls. If the

subscriber does not have “call waiting” and is not using PABX, make

no entry in this field.

To clear entries, press ✱40✱.

If call waiting is used, enter call waiting

disable digits “∗ (#+11) 70” plus “# +

13” (pause).

NOTES:

SIA-Compliant Controls: If call

waiting is used, enter call waiting

disable digits as described above,

and also set Call Waiting Disable

option in field *91.

1. The call waiting disable feature cannot be used on a PABX line.

2. Using Call Waiting Disable on a non-call waiting line will prevent

successful communication to the central station.

Primary Phone No.

Secondary Phone No.

Do not fill unused spaces.

∗41

∗42

0–9

#+11 for ' '

✱

✱ respectively

Enter up to 20 digits. To clear entries, press 41 or 42

Enter the respective phone numbers. If fewer than the maximum digits

entered, exit the field by pressing [∗]. The next data field number is displayed.

✱

#+12 for '#'

#+13 for a 2-second pause

∗43

∗44

∗45

∗46

| | | / | | | | |

[FFFFFFFFFF]

Partition 1 Primary Acct. No.

Part. 1 Secondary Acct. No.

Partition 2 Primary Acct. No.

[FFFFFFFFFF]

Partition 2 Secondary Acct. No.

Enter 4 or 10 digits, as chosen in *48

Report Format. Enter digits 0–9; #+11

for B; #+12 for C; #+13 for D; #+14 for

E; #+15 for F.

Enter [∗] as the fourth digit if a 3-digit account number (for 3+1 dialer

reporting format) is used. Enter 0 as the first digit of a 4-digit account

number for 0000-0999. E.g., For Acct. B234, enter: #+11 + 2 + 3 + 4

To clear entries in a given field, press *43*, *44*, *45*, or *46* based

on the field being programmed

Phone System Select

∗47

∗48

[1]

If Cent. Sta. is not on a WATS line:

0=Pulse Dial; 1=Tone Dial

Select the type of phone service for the installation.

If Cent. Sta. is on a WATS line:

2 = Pulse Dial ; 3 = Tone Dial

Report F ormat

[77]

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD;

2 = 4+2 ADEMCO L/S STAND.

3 = 4+2 RADIONICS STANDARD

5 = 10-digit ADEMCO CONTACT ID®

REPORTING

primary

secondary

Select the format for primary/secondary phone numbers

6 = 4+2 ADEMCO EXPRESS

7 = 4-digit ADEMCO CONTACT ID®

REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXP.;

9 = 3+1, 4+1 RADIONICS EXP

Split/Dual Reporting

0 = Standard/backup reporting only (all

to primary)

∗49

[0]

Backup Reporting: All reports are sent only to the primary number

unless unsuccessful after 8 attempts. If unsuccessful, the system will

make up to 8 attempts to send all reports to the secondary number. If

still unsuccessful after the 16 attempts, the system displays the

“COMM. FAILURE” message (FC for fixed-word displays).

1-5 = see table at right

Primary Phone No.

2nd Phone No.

Others

Open/Close, Test

All

1 = Alarms, Restore, Cancel

2 = All except Open/Close, Test

3 = Alarms, Restore, Cancel

4 = All except Open/Close, Test

5 = All

– 6 –

Burglary Dialer Delay

Delay Time:

0 = no delay

∗50

[2,0]

Delay

Time

SIA-Compliant Controls:

Delay Disable

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

Provides delay of “BURGLARY ALARM” report to the central station,

which allows time for the subscriber to avoid a false alarm transmission.

This delay does not apply to zone type 24 alarms (silent burglary) or to

24-hour zone types 6, 7, and 8 (silent panic, audible alarm, auxiliary

alarm), which are always sent as soon as they occur.

UL: Delay Time must be 0

SIA Guidelines: delay must be minimum of 15 seconds

SIA-Compliant Controls:

Delay Time:

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

Delay Disable:

0 = use delay set in entry 1

1 = dial delay disabled for zones

listed in zone list 6 (use zone list 6

to enter those zones that require

dial delay to be disabled; these

zones ignore the setting in entry 1)

UL: Dial delay plus entry delay must not

exceed one minute; use zone list 6 to

disable dial delay from appropriate zones,

if necessary.

SESCOA/Radionics Select

0 = Radionics (0-9, B-F)

1 = SESCOA (0-9 only reporting)

∗53

∗54

Enter 0 for all non-SESCOA formats.

Dynamic Signaling Delay

0 = no delay (both signals sent)

1 = 15 secs

[0]

Select delay from 0 to 225 secs, in 15-sec increments.

Intended for reporting via a communication device on the ECP bus

(LRR). This field lets you select the time the panel should wait for

acknowledgment from the first reporting destination (see ∗55) before it

attempts to send a message to the second destination. Delays can be

selected from 0 to 225 seconds, in 15-second increments. This delay is

per message. If 0 is entered in this field, the control panel will send

redundant reports to both Primary Dialer and LRR.

2 = 30 secs, etc.

UL: If using line security, must be 0.

Reports will be sent to both the dialer and

the communication device.

Dynamic Signaling Priority /

∗55

[0]

AAV Path Select

0 = Primary Dialer first / AAV via phone

line

1 = Communication Device (LRR) first /

AAV via communication device

path (see AAV Path Select

paragraph at right)

This field selects the primary communication path for reporting (dialer

or communication device) of primary phone number events (see ∗49

Split/Dual Reporting) and selects the communication path used for

AAV sessions (phone line or communication device path). Use ∗29

IP/GSM menu mode to enable the communication device being used.

For Dynamic Signaling Priority:

for messages as follows:

Select the initial reporting destination

Primary Dialer First selected (0):

• If acknowledged before delay expires (see ∗54), then message will

not be sent via LRR.

For UL Commercial Burglary installations

that use a DACT and LRR, this field must

be 0.

• If not acknowledged before delay expires, message is sent to both

the Primary Phone No. and via LRR.

Long Range Radio First selected (1):

• If acknowledged before delay expires, then message will not be sent

to the primary dialer.

• If not acknowledged before delay expires, message is sent to both

the Primary Phone No. and via LRR.

For AAV Path Select:

• If using the UVS system or AVS system with non-ECP connection,

option 0 must always be used.

• If using the AVS system with ECP connection, either option (0 or 1)

may be used, but note the following:

IMPORTANT: If option “1” is selected, a 2-way voice (AAV) device

compatible with the communication device path must be used (ex.

GSMV communicator). When selected, AAV sessions always occur

via the GSMV communicator, even if reporting reverts to phone line

backup due to GSMV communicator path reporting failure.

∗56, ∗57, ∗58 Menu Modes

These are Menu Mode commands, not data fields, for Zone Programming, Function Key Programming, and Expert Mode

Zone Programming respectively. See page 3 and respective sections later in this document.

– 7 –

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (∗59 thru ∗68, *70 thru ∗76, and ∗89):

For 3+1 or 4+1 Standard Format: Enter a code in the first box:

1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.

A 0 (not #+10) in the first box disables a report. A 0 (not #+10) in the second box results in advance to the next field.

For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A 0 (not #+10) in the second box will eliminate the expanded message for that report. A 0 (not #+10) in both boxes will disable

the report.

For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the

second boxes are ignored).A 0 (not #+10) in the first box disables the report.

UL: Report codes are required in fields *61, *65, *71, *72, for UL Commercial Burglar Alarm installations.

Report codes are required in fields *60, *62, *63, *64, *70, *73, *74, *75, *76, for UL Commercial Burglar Alarm installations and required for

Residential Fire Alarm installations

✱

SYSTEM STATUS REPORT CODES ( 59– 68)

Exit Error Alarm Report Code

See above for entries.

∗59

[0]

After arming the system, entry/exit and interior zones remaining open

after exit delay expires cause an alarm sound at the keypad and

external sounder (keypad also displays “EXIT ALARM”), and entry

delay begins. Disarming before the end of the entry delay stops the

alarm sounding and no message is sent to the central station. The

keypad will display “CA” (fixed-word) or “ALARM CANCELED” (alpha

display).

SIA-Compliant Controls:

[1] Always enabled.

If the system is not disarmed before entry delay expires, an “EXIT

ALARM” message (SIA-Compliant Controls: also zone alarm

message) will be sent to the central station. The keypad will display “EA”

(fixed-word ) or “EXIT ALARM” (alpha display), and alarm sounding

continues until the system is disarmed (or timeout occurs).

An Exit Alarm condition will also result if a fault occurs in an exit or

interior zone within 2 minutes following the end of the exit delay, and an

“EXIT ALARM” message will be sent to the central station (except for

SIA-Compliant Controls, see field *69 Recent Closing report). With

Contact ID format, the message will contain the zone number

and error code 374 (“ALARM–EXIT ERROR”).

Trouble Report Code

See above for entries.

∗60

[10]

Sent if a zone has a trouble condition.

See UL System Reporting Note above *59.

Bypass Report Code

See above for entries.

∗61

[00]

Sent when a zone is manually bypassed.

See UL System Reporting Note above *59.

AC Loss Report Code

See above for entries.

∗62

[10]

Timing of this report is random with up to a 4-hour delay. If AC restores

before the report goes out, there is no “AC LOSS” report.

See UL System Reporting Note above *59.

Low Bat Report Code

See above for entries.

∗63

[10]

Sent when the system’s backup battery has a low-battery condition.

See UL System Reporting Note above *59

Test Report Code

∗64

[00]

See above for entries.

Periodic Test Report Scheduling

Commands:

Sent periodically to test that the communicator and phone lines are

operational.

Frequency of report is set in Scheduling mode (event 11) or by the key

commands listed at left:

Each mode sets schedule 32 (FA168CPS) or schedule 08 (FA148CP)

to the stated repeat option; first test report sent 12 hours after

command.

See System Reporting UL Note above *59.

† NOTE: Make sure the Real-Time Clock is set to the proper time before

entering the test report schedule command to ensure that test reports are sent

when expected. (see Setting the Real-Time Clock section)

installer code +[#] + [0] + 0 = report

every 24 hrs

installer code +[#] + [0] + 1 = report once

per week

installer code +[#] + [0] + 2 = report

every 28 days

†

Open Report Code

See above for entries.

∗65

[0,0,0]

Part. 1

Part. 2

Common

Sent upon disarming the system in the selected partitions.

See UL System Reporting Note above *59.

– 8 –

Arm Away/Stay Rpt Code

See above for entries.

∗66

[0,0,0,0,0,0]

Away Stay

Part. 1

Away Stay

Part. 2

Away Stay

Common

This option allows for independent programming of Away and Stay

reports for each partition, including the common lobby.

NOTE: “OPEN” reports are not sent if the associated closing report is

not enabled.

RF Trans. Low Bat Report Code

∗67

∗68

[00]

See above for entries.

Sent when a transmitter low-battery condition exists.

UL: must be enabled if wireless devices are used

Cancel Report Code

See above for entries.

[00]

Sent upon disarming the system after an alarm condition was reported.

SIA-Compliant Controls: [10]

Report enabled.

Recent Closing Report Code

Not applicable to FA148CP/FA168CPS

See above for entries.

∗69

[11]

SIA-Compliant Controls: Field does not apply to other controls.

Similar to the Exit Error condition described in field *59, but occurs if

any burglary zone is faulted within two minutes after the initial exit

delay expires. Disarming the system within the two minutes stops the

alarm sound and displays "ALARM CANCELED " or "CA" and faulted

zone number. No message is sent to the Central Monitoring Station.

If the system is not disarmed within two minutes, the alarm sound

continues and a “recent closing” and a “zone alarm” message are

sent to the Central Monitoring Station (after dial delay expires).

SIA-Compliant Controls:

Always enabled.

✱

RESTORE REPORT CODES ( 70 – 76)

Alarm Restore Rpt Code

See above for entries.

∗70

[0]

Alarm restore signals indicate that respective alarm zone(s) are no

longer faulted. Alarm restore reports are sent to the central station at

bell timeout (field *33), if the zone(s) in alarm are actually restored to a

non-faulted state at that time. Otherwise, alarm restore report(s) for

respective alarm zones are sent when the system is disarmed.

See UL System Reporting Note above *59.

If Reports Per Armed Period Per Zone (*93) is also programmed, the

system will report alarm and restore codes as described above until the

“Reports Per Armed Period” count is reached. Disarming and rearming

will reset the “Reports Per Armed Period” count.

Trouble Restore Rpt Code

See above for entries

∗71

[00]

Sent when a trouble in a zone is restored and code + OFF performed.

See UL System Reporting Note above *59.

Bypass Restore Rpt Code

See above for entries.

∗72

[00]

Sent when a zone that has been bypassed is unbypassed.

See UL System Reporting Note above *59.

AC Restore Rpt Code

See above for entries.

∗73

[00]

Sent after AC power has been restored after an AC power outage.

See UL System Reporting Note above *59.

Low Bat Restore Rpt Code

See above for entries.

∗74

[00]

Sent after a system low-battery condition is restored to normal.

See UL System Reporting Note above *59.

RF Trans. Lo Bat Rst Rpt Code

See above for entries.

∗75

[00]

Sent when a transmitter’s low battery condition is restored (i.e., new

battery installed).

UL: must be enabled if wireless devices are used. See UL System Reporting

Note above *59.

Test Restore Rpt Code

See above for entries.

∗76

[00]

This is sent when the Test mode is exited or upon timeout (4hrs).

See UL System Reporting Note above *59.

– 9 –

✱

OUTPUT AND SYSTEM SETUP ( 77 – 93)

Daylight Savings Time Start/End

Month

0 = Disabled

1-9 = January-September

(1 = Jan, 2 = Feb, etc)

#+10 = October

#+11 = November

#+12 = December

∗77

[3][11]

Enter the start and end month for daylight savings time, if applicable to

the region.

Daylight Savings Time Start/End

∗78

[2][1]

Weekend

0 = disabled

1 = first

Enter the start and end weekend for daylight savings time, if applicable

to the region.

4 = fourth

5 = last

2 = second

3 = third

6 = next to last

7 = third to last

∗79, *80, *81, *82 Menu Modes

These are Menu Mode commands, not data fields, for Output Device Mapping, Output Programming, Zone List Programming,

and Alpha Programming respectively. See page 3 and their respective sections for procedures.

Auto Stay Arm

0 = no

∗84

[FA168CPS: 3; FA148CP: 1]

If enabled, the system will automatically change AWAY mode to STAY

mode if the entry/exit door is not opened and closed within the exit

delay time after a user arms in AWAY mode from a wired keypad (non-

RF device). An Opening report followed by an Armed Stay report is

sent to the Central Station.

1 = partition 1 only

2 = partition 2 only

3 = both partitions

If the door is opened and closed within the exit delay period, the

system remains in AWAY mode.

Any RF device that arms the system AWAY overrides this feature and

the system remains armed AWAY.

Cross Zone Timer

∗85

∗86

[0]

0 = 15 secs 6 = 2-1/2 min #+12 = 8 min

Sets the maximum amount of time in which two cross zones must be

tripped in an armed system to send an alarm message to the Central

1 = 30 secs 7 = 3 min

2 = 45 secs 8 = 4 min

3 = 60 secs 9 = 5 min

4 = 90 secs #+10 = 6 min

#+13 = 10 min

#+14 = 12 min

#+15 = 15 min Station. If only one cross zone is tripped during this time, a trouble

message (CID code 380) for that zone is sent to the Central Station.

#+11 = 7 min

This option not for use in UL installations.

5 = 2 min

Assign cross zones on zone list 4, using *81 Menu mode.

NOTE: Cross zoning takes effect only after Exit Delay expires.

Cancel Verify Keypad Display

0 = no “alarm canceled” display

1 = display “Alarm Canceled” when

system is disarmed after an alarm has

occurred. (To clear the “ALARM

CANCELED” display, the user must

enter the security code + OFF again.)

[1]

This feature causes a “ALARM CANCELED” display on the LCD

keypad under the following conditions:

• After the kissoff of the cancel message to the Central Station,

indicating a successful transmission.

• When an alarm is successfully canceled before the Central Station

received the Alarm message. E.g., if an alarm is incorrectly triggered

and the user presses code + OFF before the dial delay time has

expired, the message will never go out to the CS.

When the Cancel report is not enabled and the system is disarmed:

a. before dialer delay expires (alarm report not sent) message

“Alarm Canceled” is displayed.

•

b. after dialer delay expires message “Alarm Canceled” is not

displayed

Misc. Fault Delay Time

∗87

[0]

0 = 15 secs 6 = 2-1/2 min #+12 = 8 min

(used with Configurable Zone Types “digit 6”)

Used with zones assigned to a configurable zone type with fault delay

#+15 = 15 min on (configurable zone type digit “6”), and sets a zone response time of

15 seconds to 15 min. It can be assigned to zones with sensors that

provide a trouble indication when an oil tank is low, or similar

applications for critical condition monitoring where a non-alarm

response is desired.

1 = 30 sec

7 = 3 min

#+13 = 10 min

#+14 = 12 min

2 = 45 secs 8 = 4 min

3 = 60 secs 9 = 5 min

4 = 90 secs #+10 = 6 min

5 = 2 min

#+11 = 7 min

UL: may only be used on non-burglar alarm/ non-fire alarm zones when used

in fire and/or UL burglar alarm installation

– 10 –

Program Mode Lockout Options

0 = standard *98 installer code lockout

(reentry only by [∗] + [#] within 50

secs after power up)

1 = lockout [∗] + [#] reentry after *98

exit (reenter via installer code or

downloader only)

2 = not applicable (option doesn’t exist)

3 = lockout local programming after *98

exit (reenter by downloader only)

∗88

[0]

This table summarizes the Program Mode Lockout options:

Exit

*88

Reentry By:

Command Entry Installer

Power-up† Downloader

*99

*98

n/a

yes

† pressing [∗] + [#] within 50 seconds of power up

Event Log Full Report Code

See box above field *59 for report code

entries.

∗89

∗90

[00]

If an Event Logging selection is made in field ∗90, a message can be

sent to the central station receiver when the log is 80% full. If the log

becomes full, new messages overwrite the oldest messages in the log.

Event Log Enables

0 = None

[3]

This system can record various events in a history log (FA168CPS =

100 events; FA148CP = 50 events). At any time, the downloader

operator can then upload the log and view or print out all or selected

categories of the log. The downloader operator can also clear the log.

Event log can also be viewed at an alpha keypad. The display/printout

at the central station will show the date, time, event, and description of

the occurrences.

1 = Alarm/Alarm Restore

2 = Trouble/Trouble Restore

4 = Bypass/Bypass Restore

8 = Open/Close. Example: To select

“Alarm/Alarm Restore”, and

“Open/Close”, enter 9 (1 + 8);

To select all, enter #15.

Data Entry Example: To select Alarm/Alarm Restore” and

“Open/Close”, enter 9 (1+ 8); to select all events, enter #15.

NOTE: System messages are logged when any non-zero entry is made.

Option Selection

0 = None

2 = Sounder Delay (delays sounding by

15 seconds)

1 = Bell Supervision Processing†

4 = AAV

8 = Exit Delay Restart/Reset ††

#+12 = AAV and Exit Delay

Restart/Reset

∗91

[8, 0]

Options

SIA-Compliant Controls:

Call Wait Disable

Select the desired options by adding the values of each desired option.

Sounder Delay: If enabled, delays external sounding by 15-seconds.

IMPORTANT: AAV should not be used when Paging or Alarm Reports

are sent to a secondary number unless the monitoring zone option is

used (which pauses calls). Otherwise, the call to the secondary number

by the communicator after the alarm report will prevent the AAV from

taking control of the telephone line, and the AAV “Listen in” session

cannot take place.

SIA-Compliant Controls:

Options: Same as for

FA148CP/FA148CPS.

Call Waiting Disable:

0 = call waiting not used

UL: must use ADEMCO UVCM module; Exit Delay Restart/Reset must be

disabled

UL: If Sounder Delay used, entry delay (*35) must be 30 sec. max.

1 = call waiting disable digits (*70)

entered in field *40; (when selected,

the system dials the entry in field *40

only on alternate dial attempts; this

allows proper dialing in the event call

waiting service is later canceled by

the user).

SIA Guidelines: Exit Delay should be enabled.

† If bell supervision is selected, you must also cut the red PCB Bell Supervision

jumper.

††“Exit Delay Restart/reset” option allows use of the [∗] key to restart the exit

delay at any time when the system is armed STAY or INSTANT. This feature

also enables automatic exit delay reset, which resets exit delay if the entry/exit

door is re-opened and closed before exit delay time expires after arming AWAY.

Automatic Exit Delay Reset occurs only once during an armed AWAY period.

Phone Line Monitor Enable

∗92

[0,0]

Entry 1:: 0 = disabled, 1-15 = 1 min - 15

min

Entry 1: Sets the length of time a phone line fault must remain after

detected before the second digit option is activated.

Entry 2: Selects the desired phone line fault response.

Option 2 may be used even if a relay unit or Powerline carrier device is

not connected to the control.

Programmed Output Device must either be programmed to be

STOPPED in field ∗80 or STOPPED by entry of [security code] + [#] + 8

+ device number. Partition in ∗80 should be set to “0,” for STOP.

UL: Field *92 must be enabled for fire alarm installations, UL commercial

burglar alarm installations and UL residential burglar alarm installations.

(#+10 = 10 min; #+11 = 11 min; #+12 =

12 min;

#+13 = 13 min; #+14 = 14 min; #+15 =

15 min)

Entry 2:

0 = Keypad display when line is faulted

1 = Keypad display plus keypad trouble

sound. Each partition turns off its

own trouble sound. No automatic

timeout.

If the control unit is used on a UL commercial burglar alarm system which

requires 2 methods of remote communication, then the control unit’s DACT

and the other method of signal transmission must monitor each other against

communication failure and line fault. The fault must be received and

annunciated within 200 seconds of its occurrence.

2 = Same as “1”, plus programmed

output device STARTS. If either

partition is armed, external sounder

activates also. External sounder

will be turned off by normal bell

timeout, or by security code plus

OFF from either partition (it does

not have to be the one that was

armed).

– 11 –

Reports In Armed Period Per

∗93

[1,0]

Zone (Swinger Suppression)

Restrict Report Pairs:

0 = Unlimited Reports

1 = 1 report pair per zone per armed

period

Restrict

SIA-Compliant Controls:

Report Pairs Unlimited Reports Enable

Selection limits the number of alarm/alarm restore message pairs per

zone sent to the CS in an armed period. Swinger suppression applies

to burglary zones only.

2 = 2 report pairs per zone per armed

period

SIA Guidelines: Must be set for option 1 or 2

SIA-Compliant Controls:

Restrict Report Pairs:

1 = 1 report pair; 2 = 2 report pairs

Unlimited Reports Enable:

0 = restrict reports to the setting in

entry 1

1 = unlimited reports for zones listed

in zone list 7; (use zone list 7 to

enter those zones that require

unlimited reporting; these zones

ignore the setting in entry 1)

✱

DOWNLOAD INFORMATION ( 94, 95)

Download Phone No.

∗94

✱

Enter up to 20 digits, 0–9; #+11 for ' ';

#+12 for '#'; #+13 for a 2-second pause.

Do not fill unused spaces. If fewer than

Enter the phone number of the downloading computer.

UL: downloading may be performed only if a technician is at the site.

Up/downloading via the Internet has not been evaluated by UL.

✱

20 digits, exit field by pressing . To

clear entries from field, press 94 .

✱

Ring Count For Downloading

0 = Disable Station Initiated Download;

1–14 = number of rings (1–9, # +10 =10,

# +11 =11, # +12 =12, # +13 =13,

# +14 =14);

15 = answering machine defeat

(# +15 =15).

∗95

[15]

Refer to the chart below and program accordingly.

phone

module machine

answer

down-

loading Set field ∗95 to…

yes

1-14 (not 0)

greater than rings set on answer machine

(e.g., if ans. machine is 4 rings, set this

field to 5). This allows access to the

phone module if the answer machine is

off.

NOTE: Do not enter 0 if using 4286

Phone Module.

yes

1-14 (not 0)

yes

15 (bypasses answer machine^†)

1-14

† NOTE: If “15” is entered to bypass an answering machine, and a 4286

Phone Module is included in the system, you should note the following:

When calling in from an off-premises phone, the user should make the initial

call, allow 1 or 2 rings only, then hang up, then call again. The phone module

will now seize the line, and 2 long tones sound, followed by the usual voice

prompt for the access code. If this procedure is not followed, phone module

operation will not be possible.

These are commands, not data fields. See page 3.)

∗96, ∗97 Initialize/Reset Defaults (

These are commands, not data fields. See page 3.)

∗98, ∗99 Exit Commands (

PAGER OPTIONS (✱160- ✱172)

The system can send various reports to several pagers (FA168CPS = up to 4; FA148CP = up to 2).

To program pager reporting, do the following:

1. Enter the pager phone number(s), preface characters, and pager report options in data fields *160 - *171.

2. Enable Pager Delay, if desired, in field *172 (delays alarm reporting for ALL pagers).

3. Make sure appropriate user open/close pager reports are enabled (see Security Codes section in User Guide). Users

that perform actions in partition 1 will, if enabled, attempt to report to all pagers enabled for open/close reporting in

partition 1. Users that perform actions in partition 2 will, if enabled, attempt to report to all pagers enabled for open/close

reporting in partition 2.

4. If using latchkey pager report, define the latchkey report schedule using Scheduling mode (master code + [#] [6] [4] then

select event type 03). System must be armed for the Latchkey report to be sent.

5. If using a function key to manually send a message to a pager, use *57 Function Key Menu mode to define the key

(function 01).

6. If reporting zone alarms and troubles to a pager, use *81 Zone List menu mode to assign the zones associated with each

†

pager (zone lists 9-12 ).

FA148CP supports zone lists 9 and 10 only.

†

– 12 –

Pager 1 Phone No.

Enter up to 20 digits.

0–9

∗160

∗161

If entering fewer than 20 digits, exit by pressing [∗] + next field number.

To clear entries, press ∗160∗.

✱

#+11 = ' '

#+12 = '#'

#+13 = 2-second pause

Pager 1 Characters

Enter the optional prefix characters, up

Up to 16 optional characters may be sent as a prefix to the 7-digit

system status code sent to Pager #1 (if used). Phone number in field

*160 must have been entered. If fewer than 16 characters, exit by

pressing [∗] and next field number. To clear entries: press ∗161∗.

The 16 characters may be composed of the following:

PIN number, Subscriber account number,

to 16 digits.

0–9

✱

#+11 = ' '

#+12 = '#'

#+13 = 2-second pause

∗ (enter # + 11 to send ∗), # (enter # + 12 to send #), Pause (enter # +

13 to allow a 2-second pause),^†

special character(s) the user may decide to transmit

† Some paging systems require pause(s) before the prefix.

The Pager format for the 7-digit status code is defined as follows: XXX-

YYYY where:

XXX

= 3-digit event code: 911 = Alarm, 811 = Trouble,

101 = Opening (disarm), 102 = Closing (arm AWAY)

YYYY = 4-digit user or zone number (depending on type of event).

The first digit indicates partition (0 = system, 1 = part 1, 2 =

part 2, 3 = common), followed by the 3-digit user or zone

number.

Display Example 1. 9 1 1 – 1 0 0 4 Indicates an alarm (911) caused by

a fault in zone 4 (0004) in part. 1.

Display Example 2. 1 0 2 – 2 0 0 5 Indicates the system is reporting a

closing–system arming (102) by User 5 (0005) in partition 2.

Pager 1 Report Options

∗162

[0,0,0]

0 = no reports sent

P1 P2

comm

†

1 = Opens/closes all users

For each partition, select from the listed options.

4 = All alarms and troubles

5 = All alarms / troubles, and

opens/closes for all users

12 = Alarms / troubles for zones

entered in zone list 9

13 = Alarms / troubles for zones

entered in zone list 9, and

opens/closes for all users

† For users enabled for paging. Reports to pager only when arming

(close)/disarming (open) from a keypad using a security code; auto-

arming/disarming, arming with assigned button, and keyswitch arming

do not send pager messages.

Pager 2 Phone No.

See field ∗160 for entries.

∗163

∗164

∗165

If entering fewer than 20 digits, exit by pressing [∗] + next field number.

To clear entries, press ∗163∗.

Pager 2 Characters

See field ∗161 for entries.

If fewer than 16 characters, exit by pressing [∗] and next field number.

To clear entries, press ∗164∗.

Pager 2 Report Options

See field *162 for reporting options.

[0,0,0]

P1 P2 comm

Select for each partition (use zone list 10 for options 12 or 13)

Pager 3 Phone No.

See field ∗160 for entries.

∗166

∗167

If entering fewer than 20 digits, exit by pressing [∗] + next field number.

To clear entries, press ∗166∗

Pager 3 Characters

See field ∗161 for entries.

If fewer than 16 characters, exit by pressing [∗] and next field number.

To clear entries, press ∗167∗.

[0,0,0]

Pager 3 Report Options

∗168

∗169

P1 P2 comm

See field *162 for reporting options.

Select for each partition (use zone list 11 for options 12 or 13).

Pager 4 Phone No.

See field ∗160 for entries.

If entering fewer than 20 digits, exit by pressing [∗] + next field number.

To clear entries, press ∗169∗.

Pager 4 Characters

See field ∗161 for entries.

∗170

If fewer than 16 characters, exit by pressing [∗] and next field number.

To clear entries, press ∗170∗.

– 13 –

[0,0,0]

P2 comm

Pager 4 Report Options

∗171

∗172

See field *162 for reporting options.

Select for each partition (use zone list 12 for options 12 or 13).

Pager Delay Option For Alarms

0 = none

1 = 1 minute

2 = 2 minutes

3 = 3 minutes

[3]

This field determines the delay of alarm reports to the pager. This gives

the Central Station enough time to verify the alarm report it received

before the dialer attempts to dial the pager.

This delay is for ALL pagers in the system.

MISCELLANEOUS SYSTEM FIELDS (*174-*181)

Clean Me Reporting Options

0 = disable

∗174

[0] For ESL smoke detectors

This is a maintenance feature for ESL 2-wire smoke detectors on Zone

1. If used, this option limits the number of smoke detectors to a

maximum of 10, rather than 16. To enable the “clean me” feature, a

time response setting of “3” (1.2 seconds) must be entered in ∗56 Zone

Programming for zone 1.

1 = Clean Me signal reports

NOTE: If Clean Me is enabled, you must enter “3” in field ∗56

programming for zone 1 response time.

Device Duration 1, 2

∗177

[0] [0]

0 = 15 secs 6 = 2-1/2 min #+11 = 7 min

1 = 30 secs 7 = 3 min

2 = 45 secs 8 = 4 min

3 = 60 secs 9 = 5 min

4 = 90 secs #+10 = 6 min #+15 = 15 min

5 = 2 min

#+12 = 8 min

#+13 = 10 min

#+14 = 12 min

(used in *80 Menu mode-Device Actions 5/6)

These entries set the duration for output action options 5 (duration 1)

and 6 (duration 2) programmed in ∗80 Output Function Programming.

50/60 Hertz AC Operation

0 = 60 Hz; 1 = 50 Hz

∗181

[0]

Select the type of AC power applied to the control (option is used for

Real-Time Clock synchronization)

CONFIGURABLE ZONE TYPE OPTIONS (*182-*185)

(see Configurable Zone Type Worksheet)

• The system allows you to define custom zone types (FA168CPS supports 4 [types 90-93]; FA148CP supports 2 [types 90,

91]), based on the options described at right.

• All configurable zone types can be programmed via the downloader. Zone types 90-91 can also be programmed from a

keypad using data fields *182-*185.

• IMPORTANT: Be careful when selecting combinations of options for configurable zone types. Contradictory options can

cause unpredictable results.

Configurable Zone Type Options

Auto Restore (entry 2): Faults on zones set for this option are cleared; restore messages sent upon restoral of faults.

Vent Zone (entry 2): Zones set for this option are ignored if faulted when arming the system, but are protected if the zone is

later restored (e.g., an open window can be ignored when arming, but if the window is later closed, it will be protected;

opening the window again causes an alarm.)

Bypass Disarmed (entry 4): Zones set for this option can be bypassed only while the system is disarmed.

Bypass Armed (entry 4): Zones set for this option can be bypassed when the system is armed.

Dial Delay (entry 6): Alarms on zones set for this option participate in dial delay central station reporting, if system dial delay

enabled in field *50.

Fault Delay (entry 6): Faults on zones set for this option are delayed by the time set in field *87. Do not use this option if

using entry/exit delay for this zone type.

Faults Display (entry 7): Selects how faults on zones set for this zone type are displayed.

Power Reset/Verification(entry 7): Selects whether the system resets power (when user enters code + OFF), and whether

the system performs alarm verification (see description for zone type 16 in Zone Type Definitions section) when a fault

occurs on these zones.

Use Entry Delay (entry 8): Selects whether to use the system’s entry delay times.

Use Exit Delay (entry 8): Selects whether to use the system’s exit delay time.

Interior Type (entry 8): Zones set for this option are treated same as standard zone type 4 (bypasses when armed STAY,

faults displayed).

Alarm Sounds (entry 9): Selects the type of alarms sound for zones set for this zone type.

Bell Timeout (entry 9): Alarm sounding on zones set for this option remain for the duration set in fields *32 / *33.

Fire Zone (entry 9): Zones set for this option respond in the same manner as if programmed for zone type 9. Do not set fire

zones to respond as a “fault” in entries 1-6.

Trouble Sounds (entry 10): Selects the type of trouble sounds for zones set for this zone type (periodic beeps = once every

30 seconds; trouble beeps = rapid beeping).

Chime Enable (entry 10): Zones set for this option cause a chime when Chime mode is on.

– 14 –

Configurable Zone Type 90

(0-9, #+10=10, #+11=11, #+12=12,

#+13=13, #+14=14, #+15=15).

∗182

∗183

Enter the appropriate value for each entry, 1-10, based on the charts

provided in the Configurable Zone Type Worksheet section. Each entry

is the sum of the values of its selected options

To calculate the value for each entry, add the values of the selected

options in each of the entry’s columns shown in the respective chart

(one option per column). For example, to program entry 2 for “alarm

response to short,” “auto restore on,” but not a “vent zone,” enter 5 (“1”

for alarm short + “4” for auto restore-yes + “0” for vent zone-no).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

Enter the desired 3-digit Contact ID® report codes for alarms and

troubles occurring on zones assigned to this zone type. Enter the

codes sequentially (all 6 digits). When entering digits, [#] moves cursor

back, [∗] moves forward.

Zone Type 90 Report Codes

90 ALARM ID: XXX

TROUBLE ID: XXX

NOTE: Zone alarm report codes and trouble report code (∗60) and

relevant restore codes must be enabled in order to report configurable

zone type codes.

Press [∗] when done to continue.

Important Notice on Report Codes: To avoid confusion at the central

station, it is recommended that existing Contact ID® codes be used

with configurable zone types whenever possible. Check with the central

station for a complete list of Contact ID® report codes. If none of the

codes are suitable, choose a code in the reserved range of 750-789

and make sure to define the code with your central station.

Configurable Zone Type 91

(0-9, #+10=10, #+11=11, #+12=12,

#+13=13, #+14=14, #+15=15)

∗184

See ∗182 for entries.

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

See ∗183 for entries.

Zone Type 91 Report Codes

91 ALARM ID: XXX

TROUBLE ID: XXX

∗185

∗189

AUI Device Enables

(for Touch Screen Style Keypads)

FA168CPS: Enter each touch screen

keypad’s home partition

0 = disable

1 = partition 1

2 = partition 2

3 = partition 3 (common)

[1, 1, 0, 0]

AUI 1

AUI 2 AUI 3 AUI 4

System supports touch screen style keypads (e.g., Symphony

Advanced User Interface, and 6270 Touch Screen Keypad;

FA168CPS = up to 4; FA148CP = up to 2).

NOTE: Use of touch screen style keypads does not affect the number

of standard keypads supported.

AUI Compatibility Note: To ensure proper AUI device operation, use

AUI devices with the following rev levels: FA700KP series use

version 1.0.9 or higher; 8132/8142 (Symphony) series use version

1.1.175 or higher.

FA148CP:

0 = disable

1 = enable

Touch Screen (AUI) device 1: Must set device address to 1

Touch Screen (AUI) device 2: Must set device address to 2

Touch Screen (AUI) device 3: Must set device address to 5

Touch Screen (AUI) device 4: Must set device address to 6

– 15 –

KEYPAD OPTIONS *190-*199

To enable keypads:

1. Set desired address at keypad (refer to keypad’s instructions for setting the address).

2. Use data fields *190-*196 to enable keypad addresses, assign a partition, enable sound options in field.

3. Use fields *197, *198, and *199 to turn on partition number display, exit time interval display, and select fail display mode.

4. Set keypad-related data fields as appropriate: *21 Quick Arm Enable, *23 Forced Bypass, *84 Auto STAY Arm

NOTES: 1. Options for keypad 1, address 16, are set by the factory and cannot be changed.

2. Each keypad must be assigned a unique address. Keypads programmed with the same address will give

unpredictable results.

Keypad 2 Device Address 17

∗190

[0] [0]

Partition/ Enable:

Partition/

Enable

Sound

FA168CPS: Enter partition where:

0 = keypad disabled

Partion/Enable: For FA168CPS, enter the partition in which the

keypad is located; for FA148CP, enter 1 to enable, or 0 to disable the

keypad.

1-3 = part. no. (3 = common)

FA148CP:

0 = disable

1 = enable

Sound: 0 = no suppression

1 = suppress arm/disarm and Entry/Exit

beeps

Sound: Enter the desired sound option for this keypad.

2 = Suppress chime beeps only

3 = suppress arm/disarm, Entry/Exit,

and chime beeps

Keypad 3 Device Address 18

See field ∗190 for entries.

∗191

∗192

∗193

∗194

∗195

∗196

∗197

[0] [0]

Part/Enable Sound

Keypad 4 Device Address 19

See field ∗190 for entries.

[0] [0]

Part/Enable Sound

Keypad 5 Device Address 20

See field ∗190 for entries.

[0] [0]

Part/Enable Sound

Keypad 6 Device Address 21

See field ∗190 for entries.

[0] [0]

Part/Enable Sound

Keypad 7 Device Address 22

See field ∗190 for entries.

[0] [0]

Part/Enable Sound

Keypad 8 Device Address 23

See field ∗190 for entries.

[0] [0]

Part/Enable Sound

Exit Time Display Interval

0 = no display

[0]

If enabled, keypads display the exit time remaining after arming the

system, updated at the interval selected (i.e. if the exit delay is 30

seconds and “2” is selected in this field, the keypad display refreshes

every 2 seconds, displaying 30, 28, 26, 24, etc.).

1-5 = seconds between display refresh

An interval greater than “1” may be necessary for some older keypads

to allow users time to enter key presses between display updates.

NOTE: If enabled and using only 2-digit fixed-word keypads (e.g.,

FA245RF), do not set exit delay time greater than 96 seconds. Using a

longer delay time may cause end-user confusion because 2-digit

display keypads cannot display times greater than “99.” If longer exit

time is required by the installation, it is recommended that the Exit

Time Display option be disabled (“0”).

TOUCH SCREEN DEVICE NOTE: If using more than one touch screen

device (e.g., FA700KP, Symphony) with the system, leave field *197

Exit Time Display Interval set to the default value “0.” The FA700KP

automatically displays remaining exit time in one-second increments.

[0]

Display Partition Number

0 = no

1 = yes (partition no. displayed)

∗198

∗199

(FA168CPS; for Alpha Display Keypads)

If selected, the partition number is displayed in the upper-left corner of

the display. This is useful when using the GOTO partition function.

ECP Fail Display

0 = 3-digit display

“1” + device address)

1 = 2-digit fixed-display as “91

[0]

Select “0” if using Alpha keypads and/or 3-digit Fixed-Word Display

keypads. ECP faults will display “1” plus the device address (00-30) of

device causing the fault (e.g., faults on device 07 display as “107”).

Select “1” if using 2-digit Fixed-Word Display keypads (e.g., certain

6128 series keypads). If selected, ECP faults for all devices will display

as “91” on 2-digit displays, and “191” on 3-digit or Alpha keypads.

– 16 –

CONFIGURABLE ZONE TYPES WORKSHEETS

Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data

fields*182-*185. Configurable zone types 92 and 93 (FA168CPS only) can only be programmed using the

downloader software.

Programming Configurable Zone Type options involves making 10 entries in data field *182 for zone type 90 and

field *184 for zone type 91, where each entry represents the sum of the values of the various options shown in the

tables below. Use fields *183 and *185 to program Contact ID report codes for these zone types.

Entries for Fields *182 and *184

ENTRY 1 (See note 5 for RF zones) ENTRY 2 (See note 5 for RF zones)

Entry Zone Type 90

(field *182)

Zone Type 91

(field *184)

Response when system disarmed and zone is:

Auto

Restore

Vent Zone

Intact EOL

Open

RF zone N/A

Shorted

RF zn off-normal

RF zone normal

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = normal

4 = alarm

8 = trouble

12 = fault

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = no

4 = yes

0 = no

8 = yes

Entry 1 = EOL + Open

Entry 2 = Short + auto restore + vent zone

ENTRY 3 (See note 5 for RF zones) ENTRY 4 (See note 5 for RF zones)

Response when armed STAY and zone is:

Byp. when

disarmed

Byp. when

armed

Intact EOL

RF zone normal

Open

RF zone N/A

Shorted

RF zn off-normal

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = normal

4 = alarm

8 = trouble

12 = fault

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = no

4 = yes

0 = no

8 = yes

To calculate the value for each entry:

Simply add the values of the selected options

in each of the entry’s columns (one option per

column). For example, to program Entry 2 for

“alarm response to short,” “auto restore on,”

but not a “vent zone,” enter 5 (“1” for alarm

short + “4” for auto restore yes + “0” for vent

zone no).

Entry 3 = EOL + Open

ENTRY 5 (See note 5 for RF zones) ENTRY 6 (See note 5 for RF zones)

Response when armed AWAY and zone is: Dial Delay

Entry 4 = Short + byp. disarmed + byp. armed

Fault Delay

(see field *50) (see field *87)

Intact EOL

Open

RF zone N/A

Shorted

RF zn off-normal

RF zone normal

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = normal

4 = alarm

8 = trouble

12 = fault

0 = normal

1 = alarm

2 = trouble

3 = fault

0 = no

4 = use delay

0 = no

8 = use delay

see note 1

Entry 5 = EOL + Open

Entry 6 = Short + dial delay + fault delay

INTACT

EOL

OPEN

SHORTED

ENTRY 7

ENTRY 8

ZONE-003-V0

Zone Conditions Represented

in Entries 1-6

Display Faults

Power Reset/

Verification

Use Entry

Delay 1/2

Use Exit

Delay

Respond as

Interior Type

0 = show alarms 0 = no

0 = no

1 = delay 1

2 = delay 2

0 = no

4 = use exit

delay

0 = no

8 = yes

NOTES:

when armed 4 = power reset

1. Do not use the “fault delay” option with a

configurable zone type if it is set for an

entry or exit delay, otherwise

& disarmed

1 = don’t show

alarms when

after fault

(by code + OFF)

12 = verification

(see zone

see note 2

unpredictable results may occur.

armed (show

alarms, trbles,

faults when

2. To create an interior type zone, select

“respond as interior zone type” (entry 8,

interior type = yes), and set zone

response to “fault” in entries 3-4 to ensure

fault displays; do not set as “normal,”

“alarm,” or “trouble.”

3. Do not set fire zones to respond as a

“fault” (entries 1-6), otherwise faults will

not display unless the [∗] key is pressed.

4. 4219/4229 modules must use EOLRs or

unpredictable results may occur.

5. RF Zones: The “open” option in entries 1,

3, and 5 is not applicable for RF zones.

Use the “intact EOL” option for normal RF

zone conditions and “shorted” for off-

normal RF zone conditions.

type 16)

disarmed)

3 = never show

any alarms,

trbles, faults

Entry 7 = fault display + power

reset/verification

Entry 8 = entry delay 1/entry delay 2 + exit delay +

interior zone type

ENTRY 9

ENTRY 10

Alarm Sounds

Use Bell

Timeout

Respond as

Fire Zone

0 = no

Trouble

Sounds

0 = none

1 = periodic

beep

2 = trouble

beeps

Chime when

Chime Mode On

0 = no

0 = none

1 = steady

keypad

0 = no

4 = yes

8 = yes

4 = yes

2 = steady bell see fields *32,

and keypad *33

3 = pulsing bell

see zone type

09; see note 4

6. a. Zone-Doubling/Double-Balanced: A

short on either zone of a zone-doubled

pair or on a double-balanced zone

causes a tamper condition.

and keypad

Entry 9 = alarm sounds + bell timeout + fire zone

Entry 10 = trouble sounds + chime

b. For double-balanced zones, this entry

must be “0.”

c. For zone-doubled zones, both zones

of the doubled pair must be assigned

the same response to a short.

– 17 –

∗56 ZONE PROGRAMMING MENU MODE

(press *56 while in Program mode) The Zone Programming Worksheet is on page 36.

Zones and Partitions

Each protection zone needs to be programmed with various attributes using *56 Zone Programming mode or 58 Expert

Programming Mode. Using this mode, enter the zone number to be programmed and make appropriate entries at the

prompts. Finally, Confirm the serial number of wireless transmitter zones.

✱

The FA168CPS system can control two independent areas of protection (known as partitions) for use by independent users, if

desired, by simply assigning zones to one or the other partition during zone programming. The FA168CPS, by default,

automatically distributes users between the two partitions. The master user can change the user number distributions.

Zones can also be assigned to a common partition, which is an area shared by users of both partitions (such as a lobby in a

building). This allows either partition to arm, while leaving the common partition disarmed for access into the other partition.

The following describes the functioning of the FA168CPS common partition:

• The common zone sounds and reports alarms only when both partitions are armed. If only one partition is armed, the

system ignores faults on the common zone.

• Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to arm

unless the common zone is first bypassed or the fault is corrected.

• Faults on the common zone are displayed on common zone keypads, and will also appear on another partition’s keypad

when that partition is armed.

• Either partition can clear and restore the common zone after an alarm.

∗56 Menu Mode

PROMPT

VALID ENTRIES

EXPLANATION

This display appears upon entry into this mode.

The default is 0 (No).

Confirm?

0 = no

1 = yes

SET TO CONFIRM?

0 = NO 1 = YES 0

If 1 (Yes) is entered, you will be prompted to confirm each

transmitter after entering the serial and loop numbers (at the

“XMIT TO CONFIRM” prompt later).

[∗] to continue

Enter the zone number that you wish to program. Zone 10 has

been entered in the example display at left.

Enter a report code for zone 91 to enable addressable device

reporting.

Enter a report code for zone 92 to enable duress reporting.

95, 96, 99 are emergency (panic) key zones.

Zone Number

FA168CPS:

wired 01-08 (and 09-48†);

wireless 09-48; RF button

zones 49-64

Enter Zn Num.

(00 = Quit) 10

FA148CP:

wired 01-06 (and 07-22†);

wireless 09-34; RF button

zones 49-56

† if zone expanders are used.

Both Controls:

91 = addr. device report enable

92 = duress report enable

95, 96, 99 =emerg. zones

[∗] to continue

00 to quit

“IN: L” appears for wireless zones and indicates input type and

loop.

“IN: AD” appears for hardwire expansion zones (AW) and

indicates the module’s address (AD), which is based on the

zone number.

Summary Screen

[∗] to continue

Zn ZT P RC In:

10 00 1 10 RF:

“HW: RT” appears for hardwire zones and indicates

configuration (EOL, NO, NC, zone doubling, double-balanced)

and response time selection.

Each zone must be assigned to a zone type, which defines the

way in which the system responds to faults in that zone. Enter the

Zone Type code from the list below:

Zone Type (ZT)

See table at right.

10 Zone Type

Perimeter

Note: If 00 is entered, Delete Zone ? will be displayed.

00 = Not used

07 = 24-Hr Audible

08 = 24-Hr Aux

09 = Fire

20 = Arm–STAY*

21 = Arm–AWAY*

22 = Disarm*

01 = Entry/exit #1

02 = Entry/exit #2

03 = Perimeter

23 = No Alarm Resp

10 = Interior w/Delay

04 = Interior Follower 12 = Monitor Zone

24 = Silent Burglary

05 = Day/Night

06 = 24-Hr Silent

14 = Carbon Monoxide 77 = Keyswitch

16 = Fire w/Verify

81 = AAV Mon. Zone

*5800 button-type transmitters only

Enter the Partition number for this zone. Partition 1 is shown

entered.

Partition No. (P)

(FA168CPS)

1-3 = partition

(3 = common)

[∗] to continue

10 Partition

– 18 –

Enter the report code for this zone, which consists of 2

hexadecimal digits, each in turn consisting of 2 numerical digits.

For example, for a report code of “10,” enter 01 and 00.

For Contact ID®, entering any non-zero entry as the first digit

enables the report code for this zone.

Report Code (RC)

10 Report Code

First Digit: 1-9, 10 for 0, 11 for

B, 12 for C, 13 for D, 14 for E,

15 for F

1st 01 2nd 00 10

00 to disable

Second Digit: same as above

[∗] to continue

This prompt appears only for zone numbers 02-08.

Zone 1 is automatically set for EOL operation.

Hardwire Type

0 = EOL

1 = NC

02 HARDWIRE TYPE

EOL

† FA168CPS

2 = NO

3 = zone doubling (ZD) ^†;

4 = double-balanced (DB)^†

[∗] to continue

Appears only for hardwire zones 01-08 (zone 02 is the display

shown).

Option 3: used for “clean me” option on zone 1 (see field ∗174).

NOTE: If zone doubling is being used, the response time

selected for zones 02-08 automatically applies to each zone’s

associated doubled zone.

Response Time (RT)

0 = 10mSec;

1 = 350mSec

2 = 700mSec

3 = 1.2 seconds

[∗] to continue

02 Response Time

This prompt is skipped for zones 2-8, or 2-16 if zone-doubling

was enabled at “Hardwire Type” prompt.

All of the RF transmitters have one or more unique factory-

assigned input (loop) ID codes. Each of the inputs requires its

own programming zone (e.g., a 5804's four inputs require four

programming zones).

Input Device type (In)

2 = AW (Aux wired zone)

3 = RF (supervised RF

transmitter

4 = UR (unsupervised RF

transmitter)

5 = Button type RF

transmitter

(unsupervised).

[∗] to continue

10 INPUT TYPE

RF TRANS

RF Transmitters can be enrolled as one of the following types:

Type

Description

Sends periodic check-in signals, as well as

fault, restore, and low-battery signals. The

trans. must stay within receiver's range.

Sends all the signals that the “RF” type

does, but the control does not supervise

the check-in signals. The transmitter may

therefore be carried off-premises.

(Supervised RF)

(Unsupervised RF)

Sends only fault signals. It will not send a

low-battery signal until it is activated. The

transmitter may be carried off-premises.

(Unsupervised

Button RF)

NOTE:

• For the built-in hardwired zones, the Input Device type is

automatically displayed as HW and cannot be edited.

• To change the input type of a previously programmed wireless

device (type RF, UR, BR) to a wired zone (type AW), you must

first delete transmitter’s serial number (see To Delete A Serial

Number prompt)

Input Serial number and

Loop Number

[∗] to continue

Used only when enrolling

wireless transmitters.

Enroll the transmitter’s serial number and loop number as

follows:

1. a. Transmit two open/close sequences (for button-type trans,

press and release the button twice, waiting about 4 secs

before pressing the button the second time).

10 INPUT S/N:

A022-4064

b. Manually enter the 7-digit serial number printed on the label

of the transmitter. Press the [∗] key to move to the “L”

position, then enter the loop number.

Use the [A] (Advance) and [B] (Back) keys to move the

cursor forward and back within the screen. Pressing the [C]

(Copy) key will insert the previously enrolled serial number,

if desired (used when programming a transmitter with

several input loops).

To delete an existing serial number, enter 0 in the loop

number field. The serial number will change to 0's. If 0

was entered in error, simply re-enter the loop number or

press [#], and the serial number will return to the display.

2. Press [∗] to continue. The system now checks for a duplicate

serial/loop number.

If no duplicate is found, the display shows the serial number

and loop number.

3. Press [∗] to continue to confirmation screen.

– 19 –

NOTE: If the [C] key is used to copy the previously enrolled

serial number, the cursor will move to the Loop column (L) with

the previous serial number displayed, and display a highlighted

question mark for the loop number.

Loop Number Change

[∗] to continue

10 INPUT S/N

A022-4064

Enter the loop number and press [✱]. The system will now

check for a duplicate serial/loop number combination.

This prompt will only appear if you answered “Yes” at the first

prompt in this section.

The system will enter a confirmation mode so that the operation

of the actual programmed input can be confirmed.

Confirmation Option

[∗] to continue

XMIT TO CONFIRM

PRESS ✱ TO SKIP

Activate the loop input or button that corresponds to this zone.

If the serial number transmitted does not match the serial

number entered, a display similar to the one shown appears. If

the loop number does not match, it will also be displayed.

If so, activate the loop input or button on the transmitter once

again. If a match is not obtained (i.e., summary display does not

appear), press the [#] key twice and then enter (or transmit) the

correct serial number.

If Serial or Loop

Numbers do not match

after activating the

transmitter

Entd A022-4063 1

Rcvd A022-4064

[∗] to continue

To delete an existing serial number, enter 0 in the loop number

field. The serial number will change to 0's.

If 0 was entered in error, simply re-enter the loop number or

press [#], and the serial number will return to the display.

To Delete a Serial No.

0 = delete serial number

# = undo deletion

10 INPUT S/N:

A000-0000

[∗] to continue

If the serial number transmitted matches the serial

number entered, the keypad will beep 3 times and a

summary display will appear, showing that zone's

programming. Note that an “s” indicates that a

transmitter’s serial number has been enrolled.

Summary Screen

[∗] to continue

Zn ZT RC In: L

10 03 10 RF: 1s

Press [∗] to accept the zone information and continue.

If you want to program descriptors for zones now, enter 1 (Yes)

and refer to the ∗82 Descriptor Programming section for

available descriptors.

Alpha Descriptors

0 = no

1 = yes

PROGRAM ALPHA?

0 = NO 1 = YES

[∗] to continue

If 0 (No) was entered above, the system will return you to the

ENTER ZN NUM. prompt for the next zone.

When all zones have been programmed, enter 00 to quit

Next Zone Number

[∗] to continue;

00 = quit

ENTER ZN NUM.

(00 = QUIT) 11

Completing Zone Programming

• When you have finished programming all zones, test each zone using the system’s TEST mode.

• Do not use the Transmitter ID Sniffer Mode for checking wireless transmitting devices, as it will only check for

transmission of one zone on a particular transmitter, NOT the zones assigned to each additional loop.

∗58 EXPERT ZONE PROGRAM MODE

(press ∗58 while in Data Programming mode)

This method is designed for use by installers with previous experience in programming First Alert Professional control panels.

This mode is also used to program wireless keys using pre-defined templates.

Select whether you want confirmation of wireless device

enrollment. (See “XMIT TO CONFIRM” prompt later in this

section.) We recommend that you confirm the programming

of every transmitter.

Confirm?

0 = no; 1 = yes; [∗] to

continue

SET TO CONFIRM?

0 = NO 1 = YES 0

If 1 (Yes) is entered, you will be prompted to confirm each

transmitter after entering the serial and loop numbers (at the

“XMIT TO CONFIRM” prompt later).

A summary screen appears, showing zone 1’s currently

programmed values.

Summary Screen

01-64 = zone number;

[∗] to continue;

Zn ZT P RC HW: RT

01 09 1 10 EL

Enter the zone number being programmed, then press [∗], which

displays a summary screen for that zone and the cursor moves

to the Zone Type location. The cursor then automatically moves

to the next locations after each entry is made.

If programming a wireless key, press the [D] key then skip to

the Wireless Key Programming Templates section following this

section. When [D] is pressed, you can choose from a series of

preset templates for easy programming of wireless key zones.

00 = quit

[D] to go to prompts for

wireless key programming

templates

When all zones have been programmed, press 00 at this prompt

to quit this menu mode.

– 20 –

A summary screen with the selected zone’s current

programming appears.

Zone Programming

ZT = see Zone Type chart

shown in *56 Menu

Mode “Zone Type”

prompt

P = partition 1, 2, 3

(common);

RC = 1 (send CID report); 0

(no report)

IN = input type;

Zn ZT P RC IN: L

10 00 1 10 RF 1

Begin programming zone information as follows:

• Enter Zone Type (ZT), Partition (P), Report Code (RC; 0-9

only; use *56 mode to enter hex codes), and Input Device

Type (IN)* sequentially, but not the Loop No. (L).

• Use the [A] (Advance) and [B] (Back) keys on the keypad to

move the cursor within the screen.

• Use the [C] key to copy the previous zone’s attributes.

Press [✱] to save the programming and continue to the serial

number/loop number prompt. If needed, you can press the [#]

key to back up without saving.

L = loop number

[∗] to continue

* If HW (hardwired) or AW (Auxiliary) is entered for Input Device

Type, the next screen will be similar to the prompt shown, except

that HW or AW will be displayed under “IN”.

If RF, BR, or UR is entered, a prompt for Serial and Loop

number will be displayed, as described in ∗56 Menu mode

section.

When done, the display returns to the initial summary screen

prompt to let you program the next zone.

To exit this mode, enter 00 at the Summary Screen prompt.

WIRELESS KEY PROGRAMMING TEMPLATES

(press the [D] key from *58 Menu mode Summary Screen)

This procedure programs the wireless keys, but a key is not active for arming/disarming until it is assigned to a user

number (see System Operation section, Assigning Attributes Command in the User Guide).

•

Enter Template number 1–6 (see chart on next page).

See the defaults provided for each template in the chart that

follows these procedures.

Template Number

1–3 = 5804 templates; 4–6

= 5804BD templates

TEMPLATE ?

1–6

•

Select from templates. Press [∗] to display template (1

shown selected).

NOTE: If necessary, press [#] to back up and re-enter

template number.

•

Press [#] if you want to return to *58 Menu mode summary

screen.

When [∗] is pressed, the selected template will be displayed.

Top line of display represents loop numbers; bottom line

represents zone type assigned for each loop.

Press [∗] to accept template.

Template Display

01 02 03 04

23 22 21 23

•

Enter the partition in which the key is to be active, then press

[∗] to continue.

Partition

FA168CPS. 1 = partition 1;

2 = partition 2

PARTITION

•

The system will search for the highest available consecutive

4-zone group (the four zones in the case of the 5804 and

5804BD), and display the lowest zone number of the group.

If you want to start at a different zone, enter the zone desired,

and press [✱]. If that zone number is displayed, the system

has the required number of consecutive zones available,

beginning with the zone you entered. If not, the system will

again display a suggested zone that can be used.

Start Zone Number

ENTER START ZONE

00 = QUIT

If the required number of consecutive zones is not available

at all, the system will display “00”.

To quit this mode and return to *58 Menu mode, enter 00 at

this prompt.

•

Press [∗] to accept.

Manually enter the serial number printed on the label for the

wireless key or press and release the button to transmit its

serial number.

Serial Number

INPUT S/N

AXXX-XXXX

–

•

Press [∗] to accept the serial number. The system will check

for a duplicate.

If necessary, press the [#] key to back up without saving, and

re-enter the serial number.

Use the [A] key to move forward within the screen, and the

[B] key to move backward.

– 21 –

•

If “Yes” was entered at the SET TO CONFIRM? prompt

previously (see first prompt following entry into the ∗58

Expert Programming Mode), the display on the left will

appear. Confirm serial and loop numbers by activating the

wireless key.

Confirm

[∗] to continue

XMIT TO CONFIRM

PRESS ✱ TO SKIP

IMPORTANT:

When confirmed, the key is not active for arming/disarming until

it is assigned to a user number (using the assigning attributes

command, attribute “4”). See System Operation section for

procedure.

If the serial number transmitted does not match the serial

number entered, a display similar to the one shown will appear.

If the loop number does not match, it will also be displayed.

If so, activate the button on the wireless key once again. If a

match is not obtained (i.e., summary display does not appear),

press the [#] key and then enter the correct serial number.

Not Confirmed

[∗] to continue

Entd A022-4063

Rcvd A022-4064

If the serial number transmitted matches the serial number

entered, the keypad will beep 3 times and will return you to the

Zone Number prompt to enter the starting zone for the next

wireless key.

Or you can return to *58 Menu mode by pressing 00 at the Zone

Number prompt.

NOTE: Following the successful enrollment of each wireless

device, remove ONE of the serial number labels from the device

and affix it in the appropriate column on the ZONE

PROGRAMMING worksheet of the Programming Form; then

enter the other information (zone number, zone type, loop

number, etc.) relevant to that device.

Wireless Key Predefined Default Templates

LOOP 3

GREEN/YELLOW

LED

LOOP 2

YOU MUST

PROGRAM

THIS BUTTON

LOOP 4

OFF

LOOP 2

LOOP 1

Note:

These transmitters

are not intended for

use in UL

RED/YELLOW

LED

LOOP 4

(YOU MUST

PROGRAM

THIS BUTTON)

LOOP 3

installations.

LOOP 1

•

• •

•

• •

•

ENROLL AS "BR"

5804BD-007-V0

5804-001-V1

5804BD 2-Way Wireless Key

Transmitter

5804 Wireless Key Transmitter

For 5804

For 5804BD

TEMPLATE 1

Loop Function

Zone Type

TEMPLATE 4

Loop

Function

No Response

Arm Away

Disarm

Function

No Response

Arm Stay

Arm Away

Disarm

Function

24-hour audible

Arm Stay

Zone Type

No Response

Disarm

Arm Away

No Response

Function

No Response

Disarm

TEMPLATE 2

TEMPLATE 3

Loop

Zone Type

TEMPLATE 5

TEMPLATE 6

Loop

Zone Type

Arm Away

Arm Stay

Function

24-hour audible

Disarm

Loop

Zone Type

Loop

Zone Type

Arm Away

Arm Stay

Arm Away

Disarm

– 22 –

∗57 FUNCTION KEY PROGRAMMING MENU MODE

∗

(press 57 while in Data Programming mode).

The system provides the ability to program each of the four keypad function keys to perform one of 12 system operations. The

end user can then activate the function by simply pressing and holding the programmed key for 2 seconds. Typical functions

(listed below) include single-button arming, turning lights on/off, or single-button paging.

To assign emergency key functions (function key option “00”), first program the respective emergency zone number (95 for

“A” key, 96 for “C” key, 99 for “B” key) with the desired zone type using ∗56 (or ∗58) Zone Programming mode, then use ∗57

Function Key menu mode to assign the desired key.

To use a function key to activate a relay action (∗57 Menu mode key function 07), use ∗79 Menu mode to map the output, and

use ∗80 Menu mode to define the output’s action; select system operation type “66.”

To use a function key for a user macro, use ∗57 menu mode to activate the desired key, then define the actual macro

functions using the user code + [#] + [6] [6] command.

Press the desired function key (A-D) you want to program.

NOTE: A key programmed as a function key is no longer

available to be used as an end-user macro key or panic key.

Function Key

Press the desired function

key, A-D.

Press Key to Pgm

0 = Quit

[∗] to continue

OFF

AWAY

TEST

CODE

STAY

0 = Exit this mode

BYPASS

CHECK

MAX

INSTANT

READY

Enter the partition in which the function key is active.

Partition Number

Partition

(FA168CPS)

1 = partition 1

2 = partition 2

3 = common partition

[∗] to continue

Enter the desired function for this key, 00 to 12, from the options

listed. (00 selected for example display shown at left). Press [∗]

to returns to key number prompt with the next function key letter

Define Key Function

00-12 = see list at right

[∗] to continue; returns to

key number prompt with the

next function key letter

displayed

Key "A" Func

Zone 95

displayed.

†

For the Function key selected, the functions are predefined as

follows:

If A selected = Zone 95 (emergency key, same as [1] [∗] pair)

If B selected = Zone 99 (emergency key, same as [∗] [#] pair)

If C selected = Zone 96 (emergency key, same as [3] [#] pair)

If D selected = Single-button paging

01 = Single-button paging (sends a 999-9999 message to pager)

02 = Display time

03 = Arm AWAY (reports as User 00 if closing reports are enabled)

04 = Arm STAY (reports as User 00 if closing reports are enabled)

05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled)

†††

06 = Step Arming (arms STAY, then NIGHT-STAY

, then AWAY)

07 = Output Device Command (for device programmed as system

operation type 66–function key in *80 Menu Mode)

08 = Communication Test (sends Contact ID code 601)

09 = Macro Key 1 (define macro by user code + [#] [6] [6] command)

10 = Macro Key 2 (define macro by user code + [#] [6] [6] command)

††

11 = Macro Key 3 (define macro by user code + [#] [6] [6] command)

††

12 = Macro Key 4 (define macro by user code + [#] [6] [6] command)

† System defaults to these function key settings.

†† Macros 11-12 apply to FA168CPS only.

††† If Night-Stay zones are listed in zone list 5

– 23 –

OUTPUT DEVICE PROGRAMMING GENERAL INFORMATION (*79/*80 Menu Mode)

Output Devices:

The FA168CPS system supports up to 16 relays and/or Powerline Carrier devices (X-10 devices)

plus 2 built-in trigger outputs in any combination. These 18 “outputs” are assigned to system-wide

output numbers (01-18). Use *79 Menu Mode to assign output numbers and map them to device

addresses.

The FA148CP supports 8 relays and 2 built-in trigger outputs (total 10 outputs).

Output Functions:

The system also provides installer-defined output functions, which can be assigned to any of the

physical outputs. Therefore, the action of any one of the outputs can be based on as many of these

defined functions as desired. This lets a single relay or X-10 device perform many functions.

The control supports: FA168CPS = up to 48 defined functions; FA148CP = up to 24 functions

Use *80 Menu Mode to define output functions.

WARNING: Relays and output devices are not recommended for life safety applications.

✱

NOTE: When navigating the *79 and *80 menus: The [ ] key is used to accept an entry and advance to the next prompt.

✱

The [#] key is used to revert back to the last question to check or change an entry. Press [ ] to go forward again.

Programming Output Devices

1. Use *79 Menu Mode to assign module and output numbers and map them to device addresses.

NOTE: You must map output devices using *79 Menu Mode before you can use *80 menu Mode.

2. Use *80 Menu Mode to create output definitions, which control the output devices, if desired.

3. Use *81 Zone List Menu mode to define zone lists for use with output devices if the device action is based on more than

one zone.

• To program a device for manual activation (user code + [#] [7] / [#] [8] + 2-digit device number) or for scheduled automatic

activation, simply map the device using *79 Menu mode.

• To program a device to automatically activate upon a system event (or function key), use *79 Menu mode to map the device,

then use *80 Menu mode to define the automated device action.

∗79 RELAY/POWERLINE CARRRIER DEVICE (X-10) PROGRAMMING MENU MODE

∗

(press 79 while in Programming mode) The *79 Device Mapping Worksheet is on page Error! Bookmark not defined..

Use this menu to assign Relay Module device addresses and specific relay numbers, and Powerline Carrier unit numbers. The

system is based on predefined module addresses for 4204 and 4229 modules. Refer to the table shown at the “Module

Address” prompt on the next page and set the modules’ addresses (via module DIP switches) accordingly.

The following table shows how these outputs are identified.

Output Identification

This output…

is identified by…

Relays

the Relay Module’s device address and the relay position on that module (i.e. the physical relay

number, 1-4, on that module).

X-10 Device

Built-in Outputs

a house ID (entered in data field *27) and the unit number of the device.

the output number assigned, 17 for Trigger 1 and/or 18 for Trigger 2.

This is the logical (or reference) relay number as used in the

system. Relays and X-10 devices are numbered 01-16; the on-

board triggers are numbered 17 and 18 and can be programmed

for inverted output, if required.

Device Output Number

FA168CPS:

01-16 = relays/X-10

17, 18 = on-board triggers

ENTER OUTPUT NO.

00 = QUIT

FA148CP:

01-08 = relays/X-10

17, 18 = on-board triggers

[∗] to continue

00 to quit

(prompt appears only for Triggers 17 and 18)

Selecting 0 (no) sets the output level normally high (default

setting).

Output Normally Low

0 = no (standard default)

1 = yes

17 OUT NORM LOW

0 = NO 1 = YES

Selecting 1 (yes) sets the output normally low.

Output Trigger 17 can be used for resetting 4-wire smoke

detectors by connecting it to the negative power terminal of the

smoke detector, selecting 1 at this prompt, and setting as zone

type 54, fire zone reset, in *80 Menu mode.

[∗] to continue

After entry, display returns to Output Number prompt. Use *80

Menu mode to program the function of the trigger.

– 24 –

Select whether this is a relay or a Powerline Carrier (X-10)

device.

If Powerline Carrier is selected, go to “A” prompt.

If relay is selected, skip to “B” prompt.

Output Type

0 = delete

1 = relay on 4204/4229

module

XX OUTPUT TYPE

DELETE

2 = Powerline Carrier device

(X-10)

[∗] to continue

(prompt appears if X-10 is selected)

Enter the unit code (set at the device) and press [∗].

The system returns to the Output Number prompt.

“A”

Unit Number

01-16 = predefined address

[∗] to continue

XX UNIT No.

(prompt appears if relay is selected)

Enter the predefined address for this module as listed below.

Make sure the module’s DIP switches are set to the selected

address.

“B”

Module Address

07-15 = predefined address

[∗] to continue

XX MODULE ADDR

07-15

Module Addresses

Address

Module

1st 4229 (with zones 09-16)

2nd 4229 (with zones 17-24)

3rd 4229 (with zones 25-32)

4th 4229 (with zones 33-40)

5th 4229 (with zones 41-48)

1st 4204

09^†

10^†

11^†

2nd 4204

3rd 4204

4th 4204

14^†

15^†

† These addresses apply to FA168CPS only.

This is the actual (or physical) relay number with respect to the

Relay Module upon which it is located. For 4204 modules, relay

numbers are 1-4. For 4229 modules, relay numbers are 1-2.

The system returns to the Output Number prompt for

programming the next device.

Relay Position

1-4 = relay position

[∗] to continue

XX REL POSITION

1-4

∗80 OUTPUT FUNCTION MENU MODE

∗

(press 80 while in Programming mode) The Output Definition Worksheet is on page Error! Bookmark not defined..

Use this mode to program output function definitions (up to 48 functions) that provide automated control of any of the output

Each output definition is identified

devices, based on events occurring on individual zones or zones with certain zone types.

by an output function number, and includes the following components:

Output Definition Components

Component

Output Function No.

Activated By

Event

Description

A reference number that defines an output’s characteristics.

Determines whether the initiating event occurs on a zone, a zone list, or a zone type.

Event that triggers the output action. Can be an event occurring on a specific zone number or a

zone list, or a specific zone type.

Partition

If the output is activated by zone type, this defines the partition in which the programmed event is

to cause the device action.

Output Action

Defines the action of the relay/X-10 device when the defined event occurs. Can close for 2

seconds, stay closed until reset, continuously pulse (1-second close-open-close-open, etc.),

toggle the device state, or activate for a defined duration (set in data field *177).

Assigns this function to a specific output number (defined in *79 Menu Mode). This is the output

number that will perform this function upon the triggering event. Note that each defined function is

associated with only one output number. This means that if more than one output device needs to

perform this particular function, you need to define another output function number with the same

attributes, but assign the appropriate output number. (i.e. output devices can be assigned more

than one function number, but each function number can only be assigned a single output

number.

Output No.

For example, if you want to pulse a strobe light upon fire alarms on zone 4 using a relay mapped to output number 2 (as

programmed in *79 Menu Mode), program the following in *80 Menu Mode:

Prompt

Entry

Output Funct. #

Activated By:

Enter Zn No.

Output Action

Output Number

01 (assuming this is the first output function)

3 (zone number)

04 (requires 2-digit zone numbers)

3 (continuous pulse)

02 (device mapped in *79 Menu Mode)

– 25 –

80 Menu Mode

Enter the output function number to be defined (or 00 to exit)

Output Function No.

(FA168CPS: 01-48

(FA148CP: 01-24)

Output Funct. #

(00 = Quit)

[∗] to continue; 00 to quit

This screen displays a summary of the current output

programming (for this example, Zone List has been selected-this

is the default screen).

Summary Screen

[∗] to continue

01 A E P Trig

?00 0 0 – ZL=00

A = Output Action; E = Triggering event; P = Partition;

Trig = Trigger type

NOTE: A question mark in the summary screen indicates that the

device number shown has not been mapped. Use *79 Menu

mode to map the device.

Select where the initiating event for this output definition is to

occur as follows:

If you enter “0,” the following prompt appears:

Activated By

01 Activated By:

Zone List

0 = delete

1 = zone list (go to “A”)

2 = zone type (go to “B”)

3 = zone number (go to “C”)

[∗] to continue

Delete?

0 = NO, 1 = YES

Press 1 to delete this output definition. The system deletes the

output function and any previous programming.

A”

(prompt appears if zone list was selected)

Zone List

01-08 = zone list

[∗] to continue

Enter the desired zone list number associated with this output

number. At the ENTER EVENT prompt, enter the zone list event

that will activate this output

01 Zn List

NOTE: Do not use pager zone lists 09-12 in output definitions.

Enter Event

Alarm

0 = restore; 1 = alarm;

2 = fault; 3= trouble

NOTE: For alarm, fault, and trouble, an event on ANY zone in the

list activates the output, but ALL zones in the list must be

restored before the output is restored.

✱

Press [ ] to continue and skip to the “Output Action” prompt.

“B”

(prompt appears if zone type was selected)

Enter the desired zone type associated with this output number.

At the PARTITION prompt, enter the partition in which this zone

type will occur.

Zone Type

See list at right for available

zone types.

01 Enter Zn type

Perimeter

CHOICES FOR ZONE TYPES:

00 = Not Used

05 = Day/Night

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

09 = Fire

12 = Monitor Zone

01 = Ent/Exit #1

02 = Ent/Exit #2

03 = Perimeter

14 = Carbon Monoxide††

16 = Fire w/verification

23 = No Alarm Response

24 = Silent Burglary

04 = Interior Follower

10 = Interior w/Delay 77 = Keyswitch Zone

81 = AAV Monitor Zone

90-91 = Configurable

CHOICES FOR SYSTEM OPERATION:

20 = Arming–Stay

21 = Arming–Away

22 = Disarming

36 = **At Bell Timeout*** 58 = Duress

38 = Chime

60 = AAV

61 = AVS/GSMV session begin§

62 = AVS/GSMV session end §

39 = Any Fire Alarm

40 = Bypassing

31 = End of Exit Time

32 = Start of Entry Time 41 = **AC Power Failure 66 = Function Key†

33 = Any Burglary Alarm 42 = **System Battery Low 67 = Bell Fail

43 = Comm. Failure

52 = Kissoff

54 = Fire Zone Reset

68 = Telco Line Cut

78 = Keyswitch Red LED

79 = Keyswitch Green LED

** Use 0 (Any) for Partition No. (P) entry.

*** Or at Disarming, whichever occurs earlier.

† Use *57 Menu Mode to assign the function key (function “07”).

†† when used with an output function, the carbon monoxide zone type

activates upon CO alarms only. Does not activate for trouble conditions.

§ automatically set when appropriate AVS Quick Command performed.

Note: In normal operation mode:

Code + # + 7 + NN Key Entry starts Device NN.

Code + # + 8 + NN Key Entry stops Device NN.

Enter the partition in which this zone type will occur.

01 Partition

0 = any partition; 1 = partition 1;

2 = partition 2; 3 = common

Any partition

✱

Press [ ] to continue and skip to the “Output Action” prompt.

– 26 –

(prompt appears if zone number was selected)

Enter the desired zone number associated with this output

number. At the ENTER EVENT prompt, enter the zone event

that will activate this output.

“C”

Zone Number

✱

Press [ ] to continue.

01 Enter Zn No.

01 Enter Event

0 = restore; 1 = alarm/fault/trouble

Restore

✱

Press [ ] to continue to the “Output Action” prompt

Enter the desired device action.

Output Action

0 = off

1 = Close for 2 seconds

2 = Stay Closed

01 Output Action

Close for 2 sec

3 = Pulse on & off (1 sec

ON, 1 sec OFF)

4 = Change Device State

5 = Duration 1 (see data

field *177)

6 = Duration 2 (see data

field *177)

✱

Press [ ] to continue.

Enter the device output number (programmed in *79 Menu

Mode) you want associated with this output.

Output Number

Enter Output No.

R02

01-16 = FA168CPS outputs

01-08 = FA148CP outputs

17-18 = on-board triggers

✱

Press [ ] to continue.

A summary screen appears showing the programmed settings.

Press [∗] to return to OUTPUT FUNCTION NUMBER prompt

Summary Screen

02 A E P TRIG

R02 1 1 3 ZL=00

✱

Press [ ] to continue.

∗81 ZONE LIST MENU MODE

(press *81 while in Programming mode) The Zone List Worksheet is on page Error! Bookmark not defined..

select an appropriate

Zone lists let you group individual zones for use with certain system actions. Using this mode, simply

zone list number, then add the desired zone numbers to be included in that list.

The following table shows the available zone lists and their purposes:

List No.

1, 2

Used for…

general purpose (GP)

chime-by-zone (see field *26 to enable option)

cross zones (see note at right)

night stay zones

Notes

• Any list may include any or all of the system's zone numbers.

• A zone list can be assigned to more than one output relay.

• Zone List 4: When creating zone list 4 for cross zoning,

include only zones assigned to zone types 3, 4, or 5. Do not

include zones that have delays (entry/exit zones, interior

w/delay) or 24-hour zones, as these zone types may produce

unpredictable operation and may not function as intended.

See field *85 for Cross Zone Timer option.

general purpose

SIA-Compliant: dial delay disable

general purpose

SIA-Compliant: unlimited reports

general purpose

zones that activate Pager 1

zones that activate Pager 2

zones that activate Pager 3 (FA168CPS)

zones that activate Pager 4 (FA168CPS)

• Zone List 6: SIA-Compliant: See field *50 for Dial Delay Disable

option.

• Zone List 7: SIA-Compliant: See field *93 for Unlimited Reports

option.

*81 Menu Mode

✱

Enter the Zone List Number to program (or 00 to quit). Press [ ]

to advance.

In the following displays, zone list 01 has been selected.

Zone List Number

01-12 = zone list number

[∗] to continue

Zone List No.

(00 = Quit)

Enter each zone number to add to the zone list, followed by

pressing [ ] (example, 01 , 02 , 03 ). After all zones are

entered, press 00 to continue.

IMPORTANT: Do not include fire zones in zone lists that are

used to STOP device actions.

† FA168CPS = 01-64; FA148CP = 01-06, 09-34, 49-56.

Zone Number

01-64 = zone numbers

followed by [∗] to

accept each zone

00 to continue

01 Enter Zn Num.

✱

†

(00 = Quit)

To delete the zone list, enter 1. All zones in the zone list will be

deleted automatically and the system returns to the Zone List

No. prompt.

Deleting Zone Lists

0 = don’t delete list

1 = delete this zone list

[∗] to continue

01 Del Zn List?

0 = No 1 = Yes

To save the zone list, enter 0.

– 27 –

To save the zone list, enter 0 and the system returns to the Zone

List No. prompt.

To delete a zone or zones in a zone list, enter 1 to continue.

Deleting a Zone

0 = don’t delete zones

1 = go to next prompt to

delete zones

01 Delete Zone?

0 = No 1 = Yes

[∗] to continue

✱

Enter each zone to be deleted from the list, followed by [ ]. After

Delete the Zone

01-64 = zones to be

deleted from list

followed by [∗] to

accept each zone

00 to continue

01 Zn to Delete?

(00 = Quit)

all zones to be deleted are entered, enter 00 to return to the

Zone List No. prompt so that another list can be programmed, if

desired.

†

† FA168CPS = 01-64; FA148CP = 01-06, 09-34, 49-56.

∗82 ALPHA DESCRIPTOR MENU MODE

The system lets you assign zone descriptors for protection zones, keypad panics, and RF receiver supervision faults. Each

description can be composed of a combination of up to 3 words selected from a vocabulary of words stored in memory (see

Alpha Vocabulary List page). In addition, up to 10 installer-defined words can be added to those already in memory, plus 3

additional words can be assigned as partition descriptors. Thus, when an alarm or trouble occurs in a zone, an appropriate

description for that zone's location can be displayed at the keypad. Zone descriptors are recommended for systems using Alpha

display keypads, and are necessary if a 4286 Phone Module is used.

✱

NOTE: You can also enter zone descriptors when the zone is being defined in 56 Menu mode.

4286 NOTE: If using a 4286 Phone Module, select from those words in the Alpha Vocabulary List shown in boldface type.

The phone module will not provide annunciation of the other words.

If a Phone Module is added to an existing system, the Alpha descriptors presently in the system should be reprogrammed,

selecting from those words shown in boldface type in the Alpha Vocabulary List. The phone module will not provide

annunciation of any other words.

∗82 Menu Mode

The “Program Alpha ?” prompt will appear. Press 1 to continue.

Program Alpha

0 = no (quit Alpha mode)

1 = yes

Program Alpha ?

0=No, 1=Yes 00

[∗] to continue

The “Custom Words” prompt will appear.

Custom Words

0 = no

1 = yes

Custom Words ?

0=No, 1=Yes 00

Press 0 to program standard alpha descriptors from the fixed

vocabulary. The system then automatically displays the descriptor

for zone 1.

Press 1 to define custom words (see “Adding Custom Words”).

Note that this is a “Summary mode,” and that no entries can be

made. Entries can be made only when the display contains a

flashing cursor, which signifies Edit mode.”

To exit the Alpha Descriptor mode, press ∗ + 0 + 0 at the

summary display.

Summary Screen

✱

ZN 01

[∗] to continue to edit mode

[#] = return to Program

Alpha prompt (to quit)

Descriptor screen for zone 1 appears. To program a descriptor

(up to 3 words) for a zone, do the following:

1. Enter the desired zone number (existing descriptor, if any, is

displayed) and press [∗], then enter the zone number again to

start edit mode (flashing cursor appears).

2. a. Press [#] plus the 3-digit number from the Alpha Vocabulary

List for the first word.

b. Press [6] to accept the word and move the cursor for the next

word in the descriptor.

Edit Mode – Flashing

Cursor

✱

ZN 01

to edit = zone number then

[∗], then zone

number again

6 = save word and go to

next word in a

descriptor

3. Repeat steps 2a and 2b for the second and third words (if used).

4. When all words for that descriptor have been entered, press [8]

to save the descriptor for that zone. The summary screen

displays for that zone and the flashing cursor disappears.

5. Press [∗] at the summary screen and repeat steps 1-4 to

assign a descriptor for the next zone.

8 = save descriptor and go

to next zone

[#] = return to Program

Alpha prompt (to quit)

6. When all descriptors have been entered, press [#]) at the last

descriptor summary screen to return to the PROGRAM

ALPHA? prompt. Enter 0 (no) at the prompt to exit this mode

and return to Data Field mode.

– 28 –

EXAMPLE: “BACK DOOR”

Descriptor Example

EXAMPLE:

(a)

a. From the list, BACK = 013, so, after entering the zone number

to be edited (step 1), enter #013. If you accidentally enter the

wrong word, simply press [#] plus the correct 3-digit number for

the word you want.

✱

ZN 01

B ACK

b. Press [6] to accept the selected word and continue to the next

word. (if this is the only word you are using for the descriptor

press [8] to save it).

(b)

✱

ZN 01 BACK

c. Enter the 3-digit number for the next word, “DOOR,” whose

number is “057.” Enter # 0 5 7.

d. Because this is the last word in the example descriptor, press

[8] to save it. (If there was a third word in the descriptor, press

[6] to accept the selected word and continue to the third word.)

(c)

✱ ZN 01 BACK

D OOR

The summary screen displays with the selected descriptor.

(d)

✱ ZN 01 BACK

DOOR

The flashing cursor disappears, indicating that the word(s) are

saved for that zone, as shown in the summary display at the left.

Summary Screen

[∗] = to enter another zone

number

[#] = return to Program

Alpha prompt (to quit)

✱ ZN 01 BACK

DOOR

✱]

To enter a descriptor for the next zone, press [ plus the

desired zone number. The summary display appears. Repeat

the previous steps to enter the descriptor for the zone.

Adding Custom Words (will not be annunciated by 4286 Phone Module)

You can add up to 10 installer-defined words to the built-in vocabulary, which can then be used when programming zone

descriptors. Each of the 10 words can actually consist of a word string of one or more words, but no more than ten

characters can be used for each word or word string.

When adding custom words, the keypad keys perform the following functions:

[4] Moves cursor one space to the left.

[6] Moves cursor one space to the right.

[8] Saves the new word in the system's memory.

1. Select Custom Word mode (enter 1) when the prompt “CUSTOM WORD ?” is displayed.

2. Enter the number (01–10†) of the custom word or word string to be created, corresponding to index numbers 245 - 254

respectively (for example, if you are creating the first custom word or word-string, enter 01, for the second, enter 02, etc.).

A cursor will now appear at the beginning of the second line.

† or 11, 12, 13 for partition 1, partition 2 and common lobby descriptors respectively. See Assigning Partition

Descriptors paragraph below.

NOTE: Custom words 8, 9, and 10 are “reminder words” that are programmed using Scheduling Mode.

3. Refer to the Character List of letters, numbers, and symbols on a following page.

Press [#], followed by the two-digit entry for the first letter you would like to display (e.g., # 65 for “A”).

The cursor moves to the right, in position for the next character.

To delete a character, simply enter the SPACE character (#32) at the unwanted character’s location..

4. Repeat Step 3 to create the desired word(s). Note that the “4” key can be used to move the cursor to the left, if necessary.

Remember, no word or word-string can exceed 10 characters (except custom message/partition descriptor word numbers

11, 12, and 13, which can be a maximum of 16 characters).

5. When the word is complete, press the [8] key to save the custom word(s) and return to the “CUSTOM WORD ?” display.

Repeat Steps 2–5 for other custom words to be entered. To change a custom word, just overwrite it. When all words have

been programmed, press [0] to return to the Descriptor entry. The custom word(s) will be automatically added to the built-

in vocabulary.

Assigning Partition/Custom Message Descriptors

FA148CP: You can create a custom message display that appears on alpha keypads instead of “System Ready.” To assign a

custom message, use word number 11 as described below.

FA168CPS: You can assign a partition descriptor (up to 16 characters) for each partition plus the common lobby. The system

displays the appropriate partition’s word instead of “DISARMED READY TO ARM.”

Use the same procedure as for adding custom words (described above), but use these word numbers in step 2:

11 = partition 1 ___________________________________________

12 = partition 2 ___________________________________________ (FA168CPS only)

13 = common lobby ________________________________________ (FA168CPS only)

Once a custom word is entered in any of these word locations (11-13), the system displays the appropriate partition’s word

instead of the default “DISARMED READY TO ARM” message.

– 29 –

ALPHA VOCABULARY LIST (For Entering Zone Descriptors)

000 (Word Space)

– A –

• 001 AIR

• 002 ALARM ∗

004 ALLEY

005 AMBUSH

• 006 AREA

• 007 APARTMENT

• 009 ATTIC ∗

010 AUDIO

– L –

– R –

155 RADIO

– V –

209 VALVE

210 VAULT

212 VOLTAGE

– W –

• 057 DOOR ∗

• 059 DOWN

• 060 DOWNSTAIRS

061 DRAWER

• 062 DRIVEWAY

• 064 DUCT

– E –

• 065 EAST

066 ELECTRIC

067 EMERGENCY ∗

068 ENTRY

• 069 EQUIPMENT

• 071 EXIT ∗

072 EXTERIOR

– F –

• 073 FACTORY

075 FAMILY

• 076 FATHERS

• 077 FENCE

• 079 FIRE ∗

• 080 FLOOR ∗

081 FLOW

• 106 LAUNDRY ∗

• 107 LEFT

108 LEVEL

• 109 LIBRARY ∗

• 110 LIGHT

111 LINE

• 113 LIVING ∗

• 114 LOADING

115 LOCK

116 LOOP

117 LOW

• 118 LOWER

– M –

• 119 MACHINE

121 MAIDS

• 156 REAR

157 RECREATION

159 REFRIGERATION

160 RF

• 161 RIGHT

• 162 ROOM ∗

163 ROOF

213 WALL

214 WAREHOUSE

• 216 WEST

• 217 WINDOW ∗

• 219 WING

220 WIRELESS

– X –

222 XMITTER

– Y –

223 YARD

– Z –

– S –

164 SAFE

– B –

165 SCREEN

166 SENSOR

• 167 SERVICE

• 168 SHED ∗

169 SHOCK

• 012 BABY ∗

• 013 BACK ∗

• 014 BAR

• 016 BASEMENT ∗

• 017 BATHROOM ∗

• 018 BED

• 019 BEDROOM ∗

020 BELL

• 021 BLOWER

• 022 BOILER

023 BOTTOM

025 BREAK

224 ZONE (No.)

• 225 ZONE ∗

• 170 SHOP ∗

171 SHORT

122 MAIN ∗

• 123 MASTER ∗

• 125 MEDICAL ∗

126 MEDICINE

128 MONEY

129 MONITOR

• 130 MOTHERS

• 131 MOTION ∗

132 MOTOR

– N –

• 226

• 227

• 173 SIDE ∗

174 SKYLIGHT

175 SLIDING ∗

• 176 SMOKE ∗

• 178 SONS

• 179 SOUTH

180 SPRINKLER

• 182 STATION

184 STORE

• 228 1ST ∗

• 229

• 230 2ND ∗

• 231

• 232 3RD ∗

• 233

• 234 4TH

• 235

• 236 5TH

• 237

• 238 6TH

• 239

• 240 7TH

• 241

• 242 8TH

• 243

082 FOIL

• 083 FOYER

084 FREEZER

• 085 FRONT ∗

– G –

• 089 GARAGE ∗

• 090 GAS

091 GATE

• 092 GLASS

093 GUEST

094 GUN

• 026 BUILDING

– C –

028 CABINET

• 029 CALL

030 CAMERA

031 CAR

033 CASH

• 134 NORTH

135 NURSERY

– O –

• 136 OFFICE ∗

• 138 OPEN ∗

139 OPENING

• 140 OUTSIDE

142 OVERHEAD

– P –

143 PAINTING

• 144 PANIC ∗

145 PASSIVE

• 146 PATIO ∗

147 PERIMETER

• 148 PHONE

150 POINT

151 POLICE ∗

152 POOL ∗

• 153 POWER

• 185 STORAGE ∗

186 STORY

190 SUPERVISED ∗

191 SUPERVISION

192 SWIMMING

193 SWITCH

– T –

194 TAMPER

196 TELCO

197 TELEPHONE

• 199 TEMPERATURE

200 THERMOSTAT

• 201 TOOL

202 TRANSMITTER

– U –

• 205 UP

• 206 UPPER

• 207 UPSTAIRS ∗

• 208 UTILITY ∗

034 CCTV

035 CEILING

036 CELLAR

• 037 CENTRAL

038 CIRCUIT

• 040 CLOSED ∗

• 046 COMPUTER

047 CONTACT

– D –

• 048 DAUGHTERS

049 DELAYED

• 050 DEN ∗

051 DESK

– H –

• 095 HALL ∗

• 096 HEAT

098 HOLDUP

099 HOUSE ∗

100 INFRARED

• 101 INSIDE ∗

102 INTERIOR

103 INTRUSION

– J –

• 244 9TH

245 Custom Word #1

246 Custom Word #2

247 Custom Word #3

248 Custom Word #4

249 Custom Word #5

250 Custom Word #6

251 Custom Word #7

252 Custom Word #8

253 Custom Word #9

254 Custom Word #10

• 052 DETECTOR ∗

• 053 DINING ∗

054 DISCRIMINATOR

055 DISPLAY

104 JEWELRY

– K –

• 105 KITCHEN ∗

Note: Bulleted (•) words in boldface type are those that are also available for use by the 4286 Phone Module. If using a

Phone module, and words other than these are selected for Alpha descriptors, the module will not provide

annunciation of those words.

Italicized words followed by an asterisk indicate those words supported by the 6160V/6150V Voice Keypads

CHARACTER (ASCII) CHART (For Adding Custom Words)

32 (space)

)

;

–

(

– 30 –

SETTING SCHEDULES

(Installer Code + [#] + [6] [4])

The system provides schedules, which can be used to automatically control 11 types of system events at pre-defined times.

Some events are reserved for the installer only.

FA168CPS: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer.

FA148CP:

Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.

NOTES:

• The master code can only access schedules 01-16 (FA148CP = 01-04) and events 00-07.

• System clock must be set before schedules can take effect.

• Programmed schedules do not take effect until the next scheduled “start” time. (e.g., if programming a schedule time window

for 8AM to 5PM, the schedule does not take effect until 8AM after the schedule has been programmed.)

Schedule Mode

Enter the desired schedule number.

To Quit, enter 00.

Schedule Number

FA168CPS

01-16 = end-user schedules

17-32 = installer-only

FA148CP

ENTER SCHED NO.

00=QUIT

01-04 = end-user schedules

05-08- = installer-only

[∗] to continue

Enter the desired event number for event you want to occur at a

specified time.

Events 10-11 are reserved for the installer only.

Enter Event

ENTER EVENT

00 = clear event

01 = Relay On/Off

02 = User Access

Latch key report (option 03) is sent to all pagers in the user’s

partition and is active only when the system is armed (message

sent is 777-7777). User must be enabled for paging (see User

Attributes in System Operation section).

03 = Latch Key Report to

Pager

04 = Forced Stay Arming^†

05 = Forced Away Arming^†

06 = Auto Disarm

† Forced bypass is automatically enabled regardless of setting

in field *23.

†† If selected, system displays custom words 8, 9, and 10 at

defined time. Can be used as installer’s reminder message to

the end user.

07 = Display “Reminder”

10 = Display custom words ^††

11 = Periodic Test Report^†††

Press [∗] to continue.

††† See key commands in Test Report Code data field *64

section to quickly set periodic test reporting intervals.

NOTE: Events 07 and 10 cause the keypad to beep every 30 seconds

when messages are displayed. Stop the beeps by pressing any key.

(For event 01-relay on/off)

Device Number

FA168CPS:

01-18 = device number

FA148CP: 01-08, 17, 18

Press [∗] to continue.

DEVICE NUMBER

Enter the physical device number as programmed in ∗79 Menu

Mode, then press [*] to continue to the “Start” prompt.

Device numbers 17 and 18 designate built-in triggers 1 and 2

respectively.

(For event 02-user access)

Group Number

GROUP NUMBER

1-8 = group number

Press [∗] to continue to the

“Start” prompt.

(FA168CPS only; for events 03-07, 10)

Partition

0 = all partitions

1 = partition 1

PARTITION

2 = partition 2

3 = common

Press [*] to continue to the

“Start” prompt.

Enter the event’s start time and days of the week to occur.

To select days, position the cursor under the desired days using

the [∗] key to move forward, then press “1” to select the day.

Start Time

START

SMTWTFS

01-12 = hour

HH MMAM 0 0 1 0 0 0 0

00-59 = minute

0 = AM; 1 = PM

Days = place “1” under days

Press [∗] to continue.

(For events 01-relay on/off; 02-user access; 03-latch key report)

Enter the event’s stop time and days of the week to occur.

To select days, position the cursor under the desired days using

the [∗] key to move forward, then press “1” to select the day.

Stop Time

STOP

SMTWTFS

01-12 = hour

HH MMAM 0 0 1 0 0 0 0

00-59 = minute

0 = AM; 1 = PM

Days = place “1” under days

Press [∗] to continue.

– 31 –

Enter the desired repeat option for this schedule.

e.g., To make a schedule that happens everyday you would

select all days with a repeat count of 1. To make a schedule that

runs for one week then stops, select everyday with a repeat

count of 0.

Repeat Option

REPEAT OPTION

0 = do not repeat

0-4

1 = repeat weekly

2 = repeat biweekly (every

other week)

3 = repeat every third week

4 = repeat every fourth week

Press [∗] to continue.

(For events 01 and 11)

Randomize

RANDOMIZE

0=NO 1=YES

If selected, the scheduled start and stop times will vary within 60

minutes of the “hour” time. For example, if a schedule is set to

start at 6:15pm, it will do so the first time 6:15pm arrives, but on

subsequent days it will start anytime between 6:00 and 6:59 p.m.

0 = no

1 = yes

Press [∗] to continue and

return to ENTER SCHED

NO. prompt to program the

next schedule.

NOTE: Do not use the random option if the start and stop times

are within the same “hour” setting, otherwise unpredictable

results may occur (e.g., the randomized stop time may occur

before the start time).

AVS SYSTEM ENABLE and QUICK PROGRAMMING COMMANDS

Applies to an AVS system using an ECP connection to the control.

1. Install the AVS module according to its instructions.

2. Use one of the control’s AVS Quick Program commands as follows (see Quick Program Command Results below for

results of each command):

• installer code + [#] + 0 + 3: enable AVS operation without panel sounds on the AVST speaker

• installer code + [#] + 0 + 4: enable AVS operation and enable panel sounds on the AVST speaker

3. Use data field ∗55 Dynamic Signaling Priority to select the desired reporting paths (phone line and/or GSMV) and path for

AAV communication.

4. To undo the Quick Command programming, use the following commands:

• installer code + [#] + 0 + 5: remove all options that were set if [#] + 03 quick command was performed

• installer code + [#] + 0 + 6: remove all options that were set if [#] + 04 quick command was performed

Quick Program Command Results

When either the #03 or #04 Quick Program command is used, the following are automatically programmed and no longer

available for other control panel purposes.

Pre-Programmed

Output Function No.

(∗80 mode)

#03 Command

FA168CPS

22 (zone type 60, relay 07) 46 (zone type 60, relay 15) Same as #03 plus:

23 (zone type 61, relay 08) 47 (zone type 61, relay 16) 17 (zone type 14, relay 05) 41 (zone type 14, relay 13)

24 (zone type 62, relay 08) 48 (zone type 62, relay 16) 18 (zone type 22, relay 05) 42 (zone type 22, relay 13)

19 (zone type 39, relay 06) 43 (zone type 39, relay 14)

#04 Command

FA168CPS

Same as #03 plus:

FA148CP

20 (zone type 33, relay 06) 44 (zone type 33, relay 14)

21 (zone type 22, relay 06) 45 (zone type 22, relay 14

Output Relay No.

(∗79 mode)

07 (addr 08, relay pos 2)

08 (addr 08, relay pos 1)

15 (addr 11, relay pos 2)

16 (addr 11, relay pos 1)

Same as #03 plus:

05 (addr 08, relay pos 4)

06 (addr 08, relay pos 3)

Same as #03 plus:

13 (addr 11, relay pos 4)

14 (addr 11, relay pos 3)

Same as #03 command

Protection Zone

(∗56/∗58 mode)

Device Address

Data Field ∗91

4229 zn 24 (zt 81, addr 08) 4229 zn 48 (zt 81, addr 11) Same as #03 command

address 08 (AVS module)

AAV enabled

address 11 (AVS module)

AAV enabled

Same as #03 command

AAV enabled

Same as #03 command

AAV enabled

SETTING THE REAL-TIME CLOCK

IMPORTANT: The Real-Time Clock must be set before the end of the installation.

NOTE: All partitions must be disarmed before the date/time can be set.

1. Master Code + [#] + [6] [3]

2. Press [∗] when the time/date is displayed.

A cursor appears under the first digit of the hour.

To move cursor ahead, press [∗]. To go back, press [#].

• Enter the 2-digit hour setting.

• Enter the 2-digit minute setting.

• Press [1] for PM or [2] for AM.

• Enter the last two digits of the current year.

• Enter the 2-digit month setting.

• Enter the 2-digit day setting.

3. To exit, press [∗] when cursor is at the last digit, or wait 30 seconds.

– 32 –

∗29 COMMUNICATION DEVICE MENU MODE (Pass-Through Programming)

This mode is for programming an IP, GSM, or IP/GSM Communicator Module using an alpha keypad. Alternatively, these

options can be programmed via the AlarmNet Direct website. After programming is complete, the module must be registered

with AlarmNet before reporting via the communication device can occur. Refer to the device’s instructions for registration

procedures.

NOTE: The module must be set to device address 3.

IMPORTANT: The use of an IP/GSM Communicator Module

requires an AlarmNet–I account. Please obtain the account

information from the central station prior to programming this

module.

Using an Alpha Keypad as a 7720P Programming Tool

READY

ARMED

When programming with ∗29 menu mode, the alpha

keypad mimics the functions of the 7720P Programming

Tool. See figure to right and table below for 7720P key

functions. Each key has two possible functions: a normal

function and a SHIFT function.

SHIFT

FUNCTION

WHEN LIT

Normal functions: The numeric values labeled directly

on the keys and the left-hand functions shown in

diagram on the ABC keys. To perform a normal key

function, simply press the desired key.

SHIFT functions: Those functions shown in diagram

above the numerical keys and the right-hand functions

shown on the ABC keys. To perform a SHIFT key

function, press SHIFT key (D key), then press the

desired function key (shift function is indicated by the lit

READY LED).

BS/ESC

(A)

(B)

(C)

(D)

N / Y

SPACE

ENTER

SHIFT

FA560

FA560KP-005-V0

7720P Emulation Template for Alpha Keypads

∗29 IP/GSM Program Mode

Press ∗29 while in Data Field Programming mode. The following prompts appear.

If using a communication device, enter 1 at this prompt and

Enable IP/GSM?

0 = no, not using IP or GSM;

1 = yes using IP and/or

GSM module

ENABLE IP/GSM?

0=No, 1=Yes

enter 1-Prog at the next prompt to program and register the

device. Use the communication device’s Installation Guide for

details of the device’s programming prompts and instructions for

registration.

[∗] to continue

[Default = 0 (no IP and/or GSM)]

Select whether you want to program the communication device

or enter the device’s diagnostic mode.

Programming /

1=PROG 2=DIAG

0=QUIT

Diagnostics Select

1= Prog (program the

IP/GSM options)

2 = Diag (enter diagnostic

mode)

Diagnostic Mode Note: Diagnostic mode option available only

for communicators with firmware version 2.4.16 or higher.

0 = Quit; returns to data field

programming mode

Normal and SHIFT key Functions While in ∗29 Menu Mode

Key Normal Key Function

(A) = BS/ESC [BS]: Press to delete entry

SHIFT Key Function

[ESC]: Press to quit Program Mode

†

Also, can reset EEPROM defaults

(B) = ↓/↑

(D) = SHIFT

[↓]: Scroll down programming

[↑]: Scroll up programming

[N]: Press for "NO" answer

[Y]: Press SHIFT-Y for "YES" answer

Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a

key is pressed. Press again for each SHIFT function desired.

1/A

2/B

3/C

4/D

5/E

6/F

7/S

8/T

[1]: For entering the number 1

[2]: For entering the number 2

[3]: For entering the number 3

[4]: For entering the number 4

[5]: For entering the number 5

[6]: For entering the number 6

[7]: For entering the number 7

[8]: For entering the number 8

[9]: For entering the number 9

[∗]: Used to select programming options

[0]: For entering the number 0

[#] / ENTER: Press to accept entries

[A]: Used for entering C.S. ID number

[B]: Used for entering C.S. ID number

[C]: Used for entering C.S. ID number

[D]: Used for entering C.S. ID number

[E]: Used for entering C.S. ID number

[F]: Used for entering C.S. ID number

[S]: Press to display diagnostic status

[T]: Press to send TEST messages

[X]: Press to reset the IP/GSM

9/X

[∗] / SPACE

[SPACE]: Not used

[#] / ENTER

No SHIFT function

† Active only when the "REVIEW?" prompt is displayed

– 33 –

ZONE TYPE DEFINITIONS

Zone types define the way in which the system responds to faults in each zone.

Type 00 Zone Not Used

Type 12 Monitor Zone

Program a zone with this zone type if the zone is not used.

Type 01 Entry/Exit Burglary #1

• Assign to zones that are used for primary entry and exit.

• Provides entry delay when zone is faulted if control is armed in

the Away, Stay, or Night-Stay modes.

• Works as a dynamic monitor of a zone fault/trouble (not alarm). In

the case of a short/open, the message, "*ALARM*-24 Hr. Non-Burg.

-#XXX " (where XXX is the zone number) will be sent to the Central

Station. The system keypad will display a “check” message

indicating the appropriate zone (but keypad beeping does not

occur). Upon restoral of the zone, the message, "*RESTORE*-24

Hr. Non-Burg. -#XXX " will be sent to the Central Station.

• The “check” message will automatically disappear from the keypad

dynamically, when the zone restores; a user code + off sequence is

not needed to reset the zone.

• No entry delay provided when the panel is armed in the

Instant/Maximum mode.

• Entry delay #1 is programmable for each partition (field *35).

• Exit delay begins whenever the control is armed, regardless of

✱

the arming mode selected, and is programmable (field 34).

• Faults of this zone type are independent of the system, and can

exist at the time of arming without interference.

Type 02 Entry/Exit Burglary #2

• Assign to zones that are used for entry and exit and require

more time than the primary entry/exit point.

• Provides a secondary entry delay, similar to entry delay #1.

• Entry delay #2 is programmable for each partition (field *36).

• Exit delay is same as described for Type 01.

• Since this is a “trouble” zone type, do not use this zone type with

relays set to activate upon “alarm.”

Type 14 24 Hour Carbon Monoxide Monitor

• Assigned to any zone with a carbon monoxide detector.

• A carbon monoxide alarm produces keypad and detector sounding

(does not affect bell output).

• Always active and cannot be bypassed.

Type 16 Fire w/Verification

• Provides a fire alarm when zone is shorted, but only after alarm

verified.

Type 03 Perimeter Burglary

• Assign to all sensors or contacts on exterior doors and windows.

• Provides an instant alarm if the zone is faulted when the panel is

armed in the Away, Stay, Night-Stay, Instant or Maximum modes.

Type 04 Interior Follower

• Assign to a zone covering an area such as a foyer, lobby, or

hallway through which one must pass upon entry (to and from

the keypad).

• Provides a delayed alarm (using the programmed entry 1 time)

if the entry/exit zone is faulted first. Otherwise this zone type

gives an instant alarm.

• Active when the panel is armed in the Away mode.

• Bypassed automatically when the panel is armed in the Stay or

Instant modes; if armed in Night-Stay mode, zones assigned to

zone list 05 (night-stay zone list) are not bypassed when

system armed in Night-Stay mode.

• Verifies alarm by resetting smoke detectors after short is detected

(removes power 7 seconds for zone 1, 3 seconds for trigger output).

Another short circuit within 90 seconds triggers fire alarm.

• Provides a trouble response when zone is open.

Type 20 Arm-Stay (BR only)

• Arms the system in Stay mode when the zone is activated.

• Pushbutton units send the user number to the central station when

arming or disarming.

• User number for button must be assigned.

Type 21 Arm-Away (BR only)

• Arms the system in Away mode when the zone is activated.

• Pushbutton units send the user number to the central station when

arming or disarming.

• User number for button must be assigned.

Type 22 Disarm (BR only)

• Disarms the system when the zone is activated.

• User number for button must be assigned.

Type 23 * No Alarm Response

• Can be used on a zone when an output relay action is desired, but

with no accompanying alarm (e.g., lobby door access).

Type 24 Silent Burglary

• Usually assigned to all sensors or contacts on exterior doors and

windows where bells and/or sirens are NOT desired.

• Provides an instant alarm, with NO audible indication at any keypad

or external sounder, if the zone is faulted when the system is armed

in the Away, Stay, Instant, or Maximum modes.

• A report is sent to the central station.

Type 77 Keyswitch

• Assign to zone wired to a keyswitch.

• Do not use input type “BR” devices with this zone type.

Type 81 AAV Monitor Zone

• Assign to zone connected to AAV module.

• Monitors 2-way voice sessions as follows:

Type 05 Trouble by Day/Alarm by Night

• Assign to a zone that contains a foil-protected door or window

(such as in a store), or to a zone covering a sensitive area such

as a stock room, drug supply room, etc.

• Can also be used on a sensor or contact in an area where

immediate notification of an entry is desired.

• Provides an instant alarm if faulted when armed in the Away,

Stay, Night-Stay, Instant or Maximum (night) modes.

• During the disarmed state (day), the system will provide a

latched trouble sounding from the keypad (and a central station

report, if desired).

Type 06 24-hr Silent Alarm

• Usually assigned to a zone containing an emergency button.

• Sends a report to the central station but provides no keypad

display or sounding.

Type 07 24-hour Audible Alarm

• Assign to a zone that has an emergency button.

• Sends a report to the central station, and provides an alarm

sound at the keypad, and an audible external alarm.

Type 08 24-hour Auxiliary Alarm

• Assign to a zone containing an emergency button, or to a zone

containing monitoring devices such as water or temperature

sensors.

• Sends a report to the central station and provides an alarm

sound at the keypad. (No bell output.)

When the zone is faulted, all alarm sounding and dialer reporting

stops, except for fire alarms, which immediately terminate the

voice session and cause a fire report to be sent.

When the zone is restored (session ended), sounding resumes (if

bell timeout has not expired) and reports that were stopped are

sent.

Type 09 Supervised Fire

• Provides a fire alarm on short circuit and a trouble condition on

open circuit. A fire alarm produces a pulsing bell output.

• This zone type is always active and cannot be bypassed.

Types 90-93 Configurable

Type 10 Interior w/Delay

Allows for various custom responses. Options include response to

entry/exit delays, response opens/shorts, types of alarm/trouble

sounding, dial delay, and unique Contact ID report codes. Types 92

and 93 can only be programmed via downloader. UL installations:

Zone Types 90 -93 may not be used as fire or burglar alarm zones on

fire or UL burglar alarm installations.

• Provides entry delay (using the programmed entry time), if

tripped when the panel is armed in the Away mode.

• Entry Delay 1 begins whenever sensors in this zone are

violated, regardless of whether or not an entry/exit delay zone

was tripped first.

• Bypassed when the panel is armed in the Stay or Instant

modes; if armed in Night-Stay mode, zones assigned to zone

list 05 (night-stay zone list) are not bypassed when system

armed in Night-Stay mode.

* The system can still be armed when these zone types are in a

faulted condition.

– 34 –

UL NOTICES

∗

1. Entry Delay No. 1 and No. 2 (fields 35, 36) cannot be greater than 30 seconds for UL Residential Burglar Alarm

installations, and entry delay plus dial delay should not exceed 1 minute. For UL Commercial Burglar Alarm

installations, total entry delay may not exceed 45 seconds.

2. For UL Commercial Burglar Alarm and UL Residential Burglar Alarm installations with line security, total exit delay time

must not exceed 60 seconds.

∗

3. The maximum number of reports per armed period (field 93) must be set to “0” (unlimited) for UL installations.

4. Periodic testing (see scheduling mode) must be at least every 24 hours.

5. Alarm Sounder plus Auxiliary Power currents must not exceed 600mA total for UL installations (Aux power 500mA

max.).

6. All partitions must be owned and managed by the same person(s).

7. All partitions must be part of one building at one street address.

8. If used, the audible alarm device(s) must be placed where it/they can be heard by all partitions.

9. For UL commercial burglar alarm installations the control unit must be protected from unauthorized access. The

tamper switch installed to protect the control unit enclosure door is suitable for this purpose.

10.Remote downloading without an alarm company technician on-site (unattended downloading) is not permissible for UL

installations.

11.Auto-disarming is not a UL Listed feature.

12.As SIA limits for delay of alarm reporting and sounding can exceed UL limits for commercial and residential

applications, the following UL requirements per UL681 are provided:

The maximum time that a control unit shall be programmed to delay the transmission of a signal to a remote monitoring

location, or to delay the energizing of a local alarm sounding device to permit the alarm system user to enter and

disarm the system, or to arm the system and exit shall not exceed:

a) 60 seconds for a system with standard line security or encrypted line security,

b) 120 seconds for a system without standard line security or encrypted line security, or

c) 120 seconds for a system that does not transmit an alarm signal to a remote monitoring location.

13. This control is not intended for bank safe and vault applications.

SIA QUICK REFERENCE GUIDE

1. ∗31 Single Alarm Sounding per Zone: If “0” selected, “alarm sounding per zone” will be the same as the “number of

reports in armed period” set in field ∗93 (1 if one report, 2 if 2 reports, unlimited for zones in zone list 7).

2. ∗34 Exit Delay: Minimum exit delay is 45 seconds.

3. ∗35/*36 Entry Delay 1 and 2: Minimum entry delay is 30 seconds.

4. ∗37 Audible Exit Warning: Feature always enabled; field does not exist.

5. ∗39 Power Up in Previous State: Must be “1,” power up in previous state.

6. ∗40 PABX Access Code or Call Waiting Disable: If call waiting is used, call waiting disable option in field *91 must be

set.

7. ∗50 Burglary Dial Delay: Delay must be minimum of 30 seconds.

8. ∗59 Exit Error Alarm Report Code: Always enabled.

∗68 Cancel Report Code: Default is “code enabled.”

10. ∗69 Recent Closing Report Code: Always enabled.

11. ∗91 Option Selection: Exit Delay option should be enabled. If call waiting is used, Call Waiting Disable must be set to

“1” (enabled).

12. ∗93 No. reports in Armed Period: Must be set for 1 or 2 report pairs.

13. Cross zone timer programming is set in field ∗85; cross zone pairs are assigned in zone list 4 using ∗81 Zone List

mode.

14. Duress code is assigned by using the “add a user code” procedure found in the User Guide. Enable Duress code

reporting by programming zone 92 using ∗56 Zone Programming mode.

15. Fire alarm verification is a built-in system feature when a zone is programmed for zone type 16.

– 35 –

WORKSHEET FOR ∗56 ZONE PROGRAMMING

(FA148CP supports up to 32 zones: 1-6, 9-34, 49-56) [default shown in brackets]

Zone Zn Type

Part.

Report

Hardwire

Type

Rsp. Time

Location

[09]

[01]

[03]

[1]

[EOL]

[1]

[EOL]

[1]

Zone Zn Type

Part.

Report

Input Type

Loop

Serial No.

Location

NOTES:

Zone Type: see chart in

∗56 Zone Programming

Menu mode section.

Report Code: enabled if

any digit entered as 1st

digit;

Hardwire Type (zns 2-8):

0 = EOL

1 = NC

2 = NO

3 = ZD

4 = DB

Input Type:

2 = AW (zones 9-48)

3 = RF (zones 9-48)

4 = UR (zones 9-48)

5 = BR (zones 49-64)

NOTE: Zones 9-16 not

available if zone

doubling enabled.

Response Time:

0 = 10msec

1 = 350msec

2 = 700msec

3 = 1.2 sec

Reserved Zones

91 = addressable device

report enable/disable

default zone type =

[05].

[1]

[BR]

N/A

92 = Duress report

enable/disable

[00] N/A**

[06] N/A**

N/A N/A

keypad [1] / [∗]

N/A

keypad [3] / [#]

keypad [∗] / [#]

** Emergency key zones 95, 96, and 99 report the partition of the keypad used to activate the emergency zones.

– 36 –

WORKSHEET FOR ∗57 FUNCTION KEY PROGRAMMING

Option Function

Comments

Paging

Time Display

Arm AWAY

Arm STAY

Arm NIGHT-STAY

Step Arming

Device Activation

Comm. Test

Macro Key 1

Macro Key 2

Macro Key 3

Macro Key 4

Emergency Keys:

Personal Emergency

Silent Alarm

Audible Alarm

Fire

Device:

zone 95

zone 99

zone 96

paging

n/a

Emergency Keys: A = paired keys [1] / [∗] (zone 95); B = paired keys [∗] / [#] (zone 99); C = paired keys [3] / [#] (zone 96)

WORKSHEET FOR ∗79 RELAY/POWERLINE CARRIER (X-10) DEVICE MAPPING

Applicable only if Relays and/or Powerline Carrier Devices are to be used.

Must program before using *80.

OUTPUT TYPE

Relay

Output Module Pos

OUTPUT TYPE (09-16 apply to FA168CPS only)

X10

Unit

No.

Relay

Output Module Pos

X10

Unit

No.

(1-4)

Description

(1-4)

Description

No.

Addr.

No.

Addr.

On-Board Trigger 1

On-Board Trigger 2

norm output =

WORKSHEET FOR ∗81 ZONE LIST PROGRAMMING

Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the

data during the displays and prompts that appear in sequence.

NOTE: Record desired zone numbers below, noting that a list may include any or all of system's zone numbers.

List No. Used For…

Contains These Zones…

General Purpose (GP)

General Purpose

Chime-by-Zone or GP

Cross Zones

(see field *26 for Chime-by-Zone option)

(see field *85 for Cross Zone Timer option)

Night-Stay Zones or GP

Dial Delay Disable or GP

Unlimited Reports or GP

General Purpose

SIA-Compliant Controls: see field *50 for Dial Delay Disable option

SIA-Compliant Controls: see field *93 for Unlimited Reports option

Zones activating pager 1

Zones activating pager 2

Zones activating pager 3

Zones activating pager 4

(FA168CPS)

– 37 –

WORKSHEET FOR ∗80 OUTPUT FUNCTION PROGRAMMING

Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you

enter the data during the displays and prompts that appear in sequence.

Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes.

✱

2. For Powerline Carrier devices (plcd), field 27 must be programmed with a House Code.

3. Tampers of expansion units cannot be used to operate devices.

Output

Function

Number

(FA168CPS:

1-48)

(FA148CP:

1-24)

Activation Type and Detail

Partition

Number

Event (for zone list/activated by)

Action

0 = off

1 = close 2 secs

2 = stay closed FA168CPS: R = relay

Output

Number

Device

Type

Activated by Zone List Zone Type Zone No.

By Zone List

By Zone No.

(P)

0=delete

1=zn list

2=zn type

3=zn no.

(ZL)

1-8 = list

(ZT)

(see table

below)

(ZN)

00=none

FA168CPS:

01-64

FA148CP:

01-06, 09-34,

49-56

(if using ZT trig)

0 = any

0 = restore

1 = alarm

2 = fault

0 = restore

1 = alrm/flt/trbl

3 = pulse

4 = toggle

1-18

T = trigger

X = X10

1 = partition 1

2 = partition 2

3 = common

5 = duration 1†† FA148CP:

6 = duration 2†† 1-8, 17, 18

3 = trouble

ZONE TYPE/SYSTEM OPERATION – Choices for Zone Types are:

00 = Not Used

05 = Trouble Day/Alarm Night 10 = Interior w/Delay

24 = Silent Burglary

01 = Entry/Exit#1

02 = Entry/Exit#2

03 = Perimeter

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

09 = Fire

12 = Monitor Zone

77 = Keyswitch

81 = AAV Monitor Zone

90-91 = Configurable

14 = Carbon Monoxide

16 = Fire w/Verification

23 = No Alarm Response

04 = Interior Follower

Choices for System Operation are:

20 = Arming–Stay

21 = Arming–Away

22 = Disarming (Code + OFF)

31 = End of Exit Time

32 = Start of Entry Time

33 = Any Burglary Alarm

36 = **At Bell Timeout***

Note: In normal operation mode:

38 = Chime

39 = Any Fire Alarm

40 = Bypassing

41 = **AC Power Failure

42 = **System Battery Low

43 = Communication Failure

52 = Kissoff

58 = Duress

60 = AAV Trigger

61 = AVS/GSMV session begin §

62 = AVS/GSMV session end §

66 = Function key†

67 = Bell Failure

68 = TELCO Line Fault

78 = Keyswitch red LED†††

79 = Keyswitch green LED†††

Code + # + 7 + NN Key Entry starts Device

Code + # + 8 + NN Key Entry stops Device

** Use 0 (any) for Partition No. (P) entry.

*** Or at Disarming, whichever occurs earlier.

† Use *57 Menu mode to assign the function key.

†† Duration is set in program field *177.

††† Device action not used for these choices.

§ automatically set when appropriate AVS Quick

Command performed.

54 = Fire Zone Reset

– 38 –

WORKSHEET FOR SCHEDULES

(installer code + [#] + [6] [4]; master code can only access schedules 01-16 for FA168CPS, 01-04 for FA148CP, and events 00-07 for both

controls; FA148CP supports up to 8 schedules, FA168CPS supports up to 32 schedules )

No.

Event

(see list below)

Device No. Group No. Partition

Start Time/

Stop Time/

Days

Repeat Random

for “01” events:

for “02” events: for “04-06” events: Days

(1-4)

(yes/no)

enter 01-18

enter 1-8 enter 1, 2, or 3

Events:

Master/Installer

00 = clear event

01 = device on/off

02 = user access

Installer Only

10 = display custom words 8-10

11 = periodic test report

03 = latch key report

04 = forced STAY arm

05 = forced AWAY arm

06 = auto disarm

07 = display “reminder”

Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week

TABLE OF DEVICE ADDRESSES

This Device

Uses Address Reports as†† Enabled By…

RF Receiver

AUI 1

AUI 2

AUI 3

100

*56 zone programming: input device type entry

automatic if AUI enable field *189 enabled for AUI 1

automatic if AUI enable field *189 enabled for AUI 2

automatic if AUI enable field *189 enabled for AUI 3 (FA168CPS)

automatic if AUI enable field *189 enabled for AUI 4 (FA168CPS)

automatic if communication device enabled in ∗29 Menu mode

automatic if phone module access code field *28 enabled

*56 zone programming: input device type entry, then:

automatic if zone no. 9-16 entered as AW type or relay assigned

automatic if zone no. 17-24 entered as AW type or relay assigned

automatic if zone no. 25-32 entered as AW type or relay assigned

automatic if zone no. 33-40 entered as AW type or relay assigned

automatic if zone no. 41-48 entered as AW type or relay assigned

*79 output device programming: device address prompt:

entered at device address prompt

AUI 4

Communication Device (LRR)

4286 Voice Module

103

104

Zone Expanders (4219/4229):

module 1 (for zones 09 - 16)

module 2 (for zones 17 - 24)

module 3 (for zones 25 - 32) 09 (FA168CPS)

module 4 (for zones 33 - 40) 10 (FA168CPS)

module 5 (for zones 41 - 48) 11 (FA168CPS)

Relay Modules (4204):

module 1

module 2

module 3

module 4

Keypads:

keypad 1

keypad 2

keypad 3

keypad 4

keypad 5

keypad 6

keypad 7

keypad 8

5800TM Module

107

108

109

110

111

112

113

114

115

entered at device address prompt

data field programming as listed below:

14 (FA168CPS)

15 (FA168CPS)

always enabled, all sounds enabled.

n/a

data field *190

†† Addressable devices are identified by “1” plus

data field *191

the device address when reporting. Enter report

data field *192

code for zone 91 to enable addressable device

reporting (default = reports enabled). See field *19

for addressable device (ECP) 3-digit/2-digit

identification keypad display options.

data field *193

data field *194

data field *195

data field *196

automatic

– 39 –

5800 SERIES TRANSMITTER INPUT LOOP IDENTIFICATION

All of the transmitters illustrated have one or more unique factory assigned input (loop) ID numbers. Each of the inputs

requires its own programming zone (e.g., a 5804's four inputs require four programming zones). For information on any

transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.

UL NOTE: The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804, 5804BD, 5814,

5816TEMP, 5819, 5819WHS & BRS, and 5850.

The 5827BD and 5800TM can be used in UL Listed Residential Burglar installations.

LOOP 3

LOOP 4

YOU MUST

LOOP 2

ENROLL

LOOP 1

THIS

BUTTON

LOOP

LOOP 1

LOOP

5800CO

ENROLL AS "RF"

5800Micra

5800SS1

ENROLL AS "RF"

5800WAVE

5801

5802 MN

ENROLL AS

"UR" OR "RF"

ENROLL AS "RF"

SET HOUSE ID

ENROLL AS"RF"

ENROLL AS

"UR OR"RF"

LOOP 3

LOOP 2

LOOP 4

SERIAL #1

LOOP 4

LOOP 3

YOU MUST

ENROLL

THIS

SERIAL #1

LOOP 2

OFF

LOOP 2

LOOP 1

YOU MUST

ENROLL

THIS

LOOP 1

OFF

SERIAL #1

LOOP 4

LOOP 1

BUTTON

SERIAL #1

LOOP 1

LOOP

BUTTON

SERIAL #2

LOOP 3

•

••

•

LOOP 1

SERIAL #2

LOOP 2

SERIAL #2 - LOOP 1 = ON + 4 BUTTONS

LOOP 4 = 3 + 4 BUTTONS

5802 MN2

ENROLL AS

"UR" OR "RF"

5804/5804E

ENROLL AS "BR"

5804BD/5804BDV

ENROLL AS "BR"

5805-6

5806/5806W3

5809

ENROLL AS "BR"

5808/5808LST/5808W3

ENROLL AS "RF"

SET HOUSE ID

ENROLL AS "RF"

LOOP 2

(REED)

LOOP 1

LOOP 2

(REED)

(PRIMARY)

LOOP 1

(TERMINALS)

LOOP 1

LOOP 2

(REED)

LOOP 2

(REED)

LOOP 2

(AUX.

CENTER)

LOOP 1

(TERMINALS)

LOOP 1

(TERMINALS)

LOOP 1

LOOP 3

(AUX.

RIGHT)

ALTERNATE

POSITION FOR

LOOP 2

5815

ENROLL AS "RF"

5817

5814

5816

ENROLL AS "RF"

5816MN

ENROLL AS "RF"

5818MNL

ENROLL AS "RF"

LOOP 2

(REED)

LOOP 2

(REED)

LOOP

LOOP 3

LOOPS

1 - 3

LOOP 1

(TERMINALS)

LOOP 1

(INTERNAL

SHOCK

LOOP 1

(TERMINALS)

LOOP 3

(TERMINALS)

SENSOR

5819

ENROLL AS "RF"

5819S (WHS & BRS)

ENROLL AS "RF"

5820/5820L

ENROLL AS "RF"

5821

ENROLL AS "RF"

5828/5828V

5853

SET HOUSE ID

ENROLL AS "RF"

SERIAL #1

LOOP 3

SERIAL #1

LOOP 2

SERIAL #1

LOOP 4

LOOP 1

(MOTION)

LOOP 1

SERIAL #1

LOOP 1

SERIAL #2

LOOP 3

SERIAL #2

LOOP 2

SERIAL #2 - LOOP 1 = ON + 4 BUTTONS

LOOP 4 = 3 + 4 BUTTONS

5890/5890PI

ENROLL AS "RF"

5897-35

ENROLL AS "RF"

5878

5894PI

ENROLL AS "RF"

5800-003-V0

ENROLL AS "BR"

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.firstalertprofessional.com

ÊK5305-5PRV5rŠ

K5305-5PRV5 11/08 Rev. B

Eiki Projector LC 5000U User Manual
Electro Voice Speaker EVI 12 User Manual
Extron electronic Universal Remote IR 301 User Manual
Ford Automobile FCS 15101 10 User Manual
Friedrich Air Conditioner BR1224W3A User Manual
Garmin Marine GPS System 398 User Manual
GE Cordless Telephone 28802 User Manual
GE Dishwasher 206C1559P195 User Manual
GE Freezer FCM5SAWH User Manual
Giant Bicycle Defy Advanced 3 User Manual