T H E S O U N D T H A T C R E A T E S L E G E N D S
Princeton
Plus
112
Type: PR 290
,
Owners Manual
P/N 048524
Princeton 112 Plus Front Panel Functions
A. INPUT - A high impedance, high sensitivity plug-in
M. REVERB - Adjusts the amount of reverb signal mixed
connection for instruments.
with the original dry signal for both the Normal and Drive
Channels.
B. VOLUME - Adjusts the overall loudness of the Normal
Channel.
N. FOOTSWITCH - Plug in connection for the optional
footswitch to select between the Normal and Drive
Channels and to switch the Reverb on and off. For
proper operation of the footswitch, the DRIVE SELECT
switch (item K) should be out. NOTE: Any good quality
patch cable will work with the remote footswitch,
however, a speaker grade cord is preferable to a coax
guitar cable if it is availability.
C. NORMAL CHANNEL INDICATOR - This LED is
illuminated when the Normal Channel is active.
D. TREBLE - Adjusts the amount of boost or cut in the
high frequency range of the Normal Channel.
E. BASS - Adjusts the amount of boost or cut in the low
frequency range of the Normal Channel.
O. PREAMP OUT - This jack provides an unbalanced
output signal from the preamp and can be used in
conjunction with the POWER AMP IN jack (item P) as a
patch point for effects units (i.e. as an effects loop). This
signal can also be used to feed recording and sound
reinforcement mixers. Additionally it can drive another
amplifier as a slave by connecting a standard guitar
cable from the PREAMP OUT jack of the master
amplifier to the POWER AMP IN jack of the slave.
F. GAIN - Adjusts the amount of preamp amplification in the
Drive Channel. Cleaner sound is achieved at lower gain
settings; high gain settings will produce more sustain
and distortion. This control works in conjunction with
the DRIVE VOLUME control (item L) to set the overall
loudness of the Drive Channel.
G. DRIVE CHANNEL INDICATOR -This LED is illuminated
when the Drive Channel is active.
P. POWER AMP IN - This unbalanced jack inputs signal
directly to the power amp. It automatically disconnects
the preamp signal when used. This is useful when using
the effects loop option or when using the PRINCETON
112 Plus as a slave amplifier.
H. CONTOUR - Adjusts the overall tone quality of the Drive
Channel without affecting the signal level. Low
CONTOUR settings will provide emphasis in the
midrange frequencies whereas a higher setting will
notch the midrange to produce sounds characteristics
of most “metal” music.
Q. HEADPHONES - This jack provides an output to
standard stereo or mono headphones for private
listening. NOTE: Use of this jack automatically
disables the main speaker. CAUTION: Prolonged
listening at high levels may be hazardous to your
hearing! This jack can also be used as an unbalanced
line output, which is post effects loop, by using either a
stereo or mono 1/4 inch phone plug connection.
I. TREBLE - Adjusts the amount of boost or cut in the
high frequency range of the Drive Channel.
J. BASS - Adjusts the amount of boost or cut in the low
frequency range of the Drive Channel.
K. DRIVE SELECT - Activates the Drive Channel. NOTE:
This switch disables the optional Channel Select
Footswitch and the Normal Channel controls.
R. POWER SWITCH - This switch turns the AC power ON
and OFF. When the switch is OFF the amplifier is
completely shut down.
L. VOLUME - Adjusts the overall loudness of the Drive
LINE CORD - This amplifier is equipped with a
grounding type supply cord to reduce the possibility of
shock hazard. Be sure to connect it to a grounded
receptacle. DO NOT ALTER THE AC PLUG.
Channel.
Princeton 112 Plus Specifications
PART NUMBER:
120V VERSION: 22-6704
230V VERSION: 22-6764
INPUT IMPEDANCE:
NOMINAL INPUT LEVEL:
POWER OUTPUT:
Greater than 1 MΩ
100 mv
65 Watts R. M.S.
RATED LOAD IMPEDANCE: 8Ω
EFFECTS LOOP: Nominal Level- -10 dBV
Output Impedance- 1k.Ω
Input Impedance 16kΩ
POWER REQUIREMENTS: 100V VERSION: 100V AC 50/60 Hz., 180W
120V VERSION: 120V AC 60 Hz., 180W
230V VERSION: 230V AC 50 Hz., 180W
240V VERSION: 240V AC 50 Hz., 180W
SPEAKER COMPLEMENT: One 8Ω Special Design 12” Speaker (P/N 025923)
DIMENSIONS:
Height: 16-1/2” (41.9cm)
Width: 18-5/8” (47.3cm)
Depth: 9” (22.9cm)
WEIGHT:
28 lbs. (12.7kg)
ACCESSORIES:
Remote Dual Footswitch - order Fender P/N 002-8122-000
Amplifier Cover - order Fender P/N 002-9883-000
WARNING:
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
THIS EQUIPMENT MUST BE EARTHED.
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.,
CORONA, CA 9 1 7 2 0
|
Fisher Paykel Ventilation Hood OB60N8DTX User Manual
Fisher Price Baby Toy 77806 User Manual
Flymo Trimmer 5119748 03 User Manual
FujiFilm Digital Camera 16315990 User Manual
Fujitsu Air Conditioner AOVG09LLCA User Manual
Fundex Games Games 07800016 User Manual
Fundex Games Games Timber Tumble User Manual
GE Coffeemaker 169184 User Manual
GE Washer Dryer WPRB9220 User Manual
Global Upholstery Co Patio Furniture 3356 User Manual