PAPER SHREDDER
Personal Series
MODELS
DM65C
PRODUCT USAGE GUIDE
DM65C
7
Confetti
Sheet capacity*:
Shred type:
Shred size:
Entry width:
5/ 32" x 1-3/ 8"
9"
Recommended use:
Maximum running time:
25-50 shredding passes per day
10-12 min. on/ 20 minutes off
*Sheet capacity measured with 20 lb., 8-1/ 2" x 11" paper with the shredder operating at rated voltage. Different paper weights, humidity, and
electrical currents will affect capacity.
PLEASE READ AND SAVE THIS MANUAL WITH YOUR ORIGINAL RECEIPT
Customer Service: 1-800-955-0959
the shredder's red LED will light and the shredder will automatically
stop until the jam is cleared.
To clear a jam:
OPERATION
This product features an auto-start sensor. This
sensor will turn on the cutting blades whenever
1. Move the power switch to the REVERSE (R) position. (NOTE: If
waste basket is full, empty it before clearing jam.) The shredder
will reverse the paper to clear the jam.
2. If the shredder jams in reverse, move the power switch to AUTO
(I) and allow to run for about five seconds. If jam does not clear,
move power switch to REVERSE (R) again and allow to run for
about five seconds. Repeat this procedure until the jam is
cleared. If necessary, use care to grasp the paper carefully and
pull out to clear the jam.
anything is inserted into the paper entry (while the power switch is in
the AUTO position). For the safety of pets and children, we recom-
mend always moving the power switch to OFF and unplugging when-
ever the shredder is unattended or not in use.
1. Assemble shredder (see "ASSEMBLY").
2. Remove any large paper clips or other foreign objects (except sta-
ples and small paper clips) from paper. If folding paper to fit paper
entry, adjust sheet capacity appropriately.
Do not attempt to shred large paper clips or other
hard materials (except staples and small paper
3. Once the jam is cleared, move the power switch to AUTO (I) for
continued shredding or OFF (O) if shredding is complete.
clips) with this machine. Extensive use of large paper clips or other hard
materials will result in damage to the cutting system and will void the
manufacturer's warranty.
MAINTENANCE
3. Be sure power switch is in OFF (O) position. Plug shredder into
proper power supply outlet.
4. Move power switch to AUTO (I) position.
Confetti-cut shredders require regular (monthly) oiling of the cutting
blades to maintain proper operation. Failure to oil the blades regular-
ly could result in reduced sheet capacity performance, excessive noise
during operation, paper jams and possibly shredder failure.
We recommend using only Powershred Lubricant #35250 (available
by contacting Fellowes) or a vegetable-based oil (such as corn or
canola) in a non-aerosol container with an extension nozzle.
When the unit is turned on and in standby mode (green LED
lights), the shredder is ready to be fed paper through the paper
entry. (See "TROUBLESHOOTING" if red LED is lit.)
NEVER insert hands or fingers into
paper entry as serious personal injury may result.
Never use flammable synthetic oil, petroleum-
based, or aerosol lubricants to oil the cutting
blades. Some agents may combust, causing serious injury.
Do not exceed recommended sheet capacity
(see "Product Usage Guide" on front cover of this
manual).
To oil the cutting blades:
1. From the top of the shredder, squeeze the recommended lubri-
cant across the full width of the blades.
2. Move the power switch to AUTO (I) position and allow the blades
to run at least 3 seconds.
3. Move the power switch to REVERSE (R) position and allow it to run
for at least 3 seconds.
5. Slide paper straight into paper entry until the shredder automatical-
ly begins shredding. The shredder automatically stops a few sec-
onds after shredding is complete. Continue shredding as desired to
a MAXIMUM shredding time of 10-12 minutes. At this time, the
machine MUST be allowed to "cool down" for a MINIMUM of 20
minutes. (See "Cool-Down Cycle" for more information.)
If the shredder jams or shuts off before the maximum shredding
time, see "Clearing a Jam" section for further instructions.
6. Move power switch to OFF (O) position when shredding is com-
plete.
4. Repeat steps 2-3 above at least 3 times.
7. Unplug power cord from outlet whenever shredder is unattended
or not in use.
8. Look through viewer to see if basket is full. If full, pull out bas-
ket and empty basket contents. Replace basket into cabinet.
Cool-Down Cycle
This shredder is protected with a special safety feature which prevents
the motor from overheating with extensive use. When shredding is
attempted beyond the machine's maximum running time, the shred-
der will automatically shut off its motor until it has cooled to an
acceptable operating level. This is normal and the shredder will
return to operation after the cool-down or "off" period. See "Product
Usage Guide" on front panel for maximum running time and related
cooling of "off" time.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is not put in
straight, a jam may result. See "Product Usage Guide" on front panel
for maximum sheet capacity for your shredder. In the case of a jam,
TROUBLESHOOTING
LIMITED WARRANTY
Fellowes warrants all the cutting cylinders of the machine to
be free of defects in material and workmanship for 5 years
from the date of
purchase by the original consumer. Fellowes warrants all other
parts of the machine to be free of defects in material and
workmanship for 1 year from the date of purchase by the orig-
inal consumer. If any part is found to be defective during the
warrant period, your sole and exclusive
Shredder will not operate.
a. Shredder is not plugged in.
b. Power switch is in the OFF (O) position.
Move switch to AUTO (I) position.
c. Shredder is jammed. See "Clearing a
Jam" section.
d. Shredder has exceeded the maximum run
time and requires a "cool-down" time. See
"Product Usage Guide" on front panel.
e. Shredder is not assembled properly. See
"Assembly."
remedy will be repair or replacement, at Fellowes’ option and
expense, of the defective part.
This warranty does not apply in cases of abuse, mishandling or
unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING
THAT OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO
THE APPROPRIATE
Shredder makes a loud
squeaking or rubbing
noise.
a. Cutting blades need to be oiled REGULAR-
LY. See "MAINTENANCE" section.
WARRANTY PERIOD SET FORTH ABOVE.
In no event shall Fellowes be liable for any
Shredder suddenly stops
while
shredding.
a. Shredder has exceeded the maximum run
time and requires a "cool-down" time. See
"Product Usage Guide" on front panel.
b. Shredder is jammed. See "OPERATION -
Clearing a Jam."
consequential or incidental damages attributable to this prod-
uct. This warranty gives you specific legal rights. You may
have other legal rights that vary from state to state.
For more detail or to obtain service under this warranty, please
contact Fellowes Customer Service at 1-800-955-0959,
Monday through Friday, 8 AM - 5 PM (Central Standard Time).
For specific instructions on obtaining service under this warran-
ty on machines purchased outside the USA, contact the appro-
priate location listed in the Contact for Service section of this
instruction manual.
Shredder shreds less than
capacity.
a. Cutting blades need to be oiled REGULAR-
LY. See "MAINTENANCE" section.
a. Shredder is not assembled properly. See
"ASSEMBLY."
b. Paper is jammed. See "OPERATION -
Clearing a Jam."
Red LED is lit.
Warrantor: Fellowes Manufacturing Company.
a. This is normal. The shredder runs a few sec-
onds longer than the paper in order to keep
the cutters clear of paper particles and
reduce the chances of a jam.
Shredder runs for a few
seconds after the paper
has cleared the cutters.
Customer Service 1-800-955-0959
www.fellowes.com
1789 Norwood Avenue • Itasca, Illinois 60143-1095
630-893-1600
®
Australia
Benelux
Canada
France
Germany
Italy
Japan
Tokyo
Poland
United Kingdom
Tullamarine, Vic
Vianen, NL
Markham, Ont.
Rennes, I-V
Garbsen, Han.
Camerano, AN
Warsaw
Doncaster, S. Yorks.
© 2001 Fellowes Printed in China. Form No. 30031B
|