Extron electronic Switch WPC 160 A EU User Manual

WPC 160 A Series • Installation Guide  
The Extron WPC 160 A EU and WPC 160 A MK are wall mounted plates that accept video, audio, and USB signals through one  
female 15-pin HD connector, one 3.5 mm tip-ring-sleeve (TRS) connector, and one USB B connector. The signals pass through  
the unit without modification and are output from the back via captive screw connectors. The captive screw connectors take wires  
from 18 AWG (1.02 mm) to 26 AWG (0.40 mm).  
The two form factors are shown in the figure  
at right:  
z
The WPC 160 A EU (left) mounts  
onto 80 mm one-gang European  
EU junction boxes. The plate is  
3.1 inches x 3.1 inches  
COMPUTER  
AUDIO  
COMPUTER  
AUDIO  
(81 mm x 81 mm).  
USB  
USB  
z
The WPC 160 A MK (right) mounts  
onto MK type one-gang UK  
electric junction boxes. The plate is  
3.35 inches x 3.35 inches  
WPC 160 EU  
(85 mm x 85 mm).  
WPC 160 MK  
WPC 160 EU  
WPC 160 MK  
VGA Wiring  
NOTE: Extron recommends Extron MHRVGA bulk cable (part number  
22‑024‑01) or assembled cables (part numbers 26‑112‑15, 26‑112‑36,  
26‑238‑01, and 26‑238‑25). The wire colors for these products are  
shown in the VGA Connections table at the top of the next page. If other  
cable products are used, the colors may not correspond to those shown  
in the table.  
O
I
D
U
R
E
T
U
P
M
O
C
The DDC and ID bit DIP switches, the +5 V pin, and the DDC pins are optional  
but they can affect the monitors supported by the system (see the table to the  
right of “DDC and ID Bit DIP Switch Settings” on the next page).  
B
S
U
U
E
0
6
1
EU Junction Box  
C
P
W
To connect wires from the VGA input to these modules, some wires must be  
cut shorter than others (see the table in the “VGA Connections” section on the  
next page). Follow these instructions:  
Extron  
WPC 160 EU  
20 mm M3  
Screws (2)  
1. Run the unterminated end of the cable to the junction box.  
2. Strip away 3 inches (7.5 cm) from the end of the outer jacket of the cable.  
3. Unravel each of the coaxial shields and twist each, individually, to make  
a wire.  
4. Cut 1 inch (2.5 cm) from the end of the individual wires marked with an  
asterisk in the VGA Connections table on the next page.  
5. Strip 3/16 inches (5 mm) of the inner jacket from the end of each wire and  
secure the wire to the appropriate captive screw connector (see the VGA  
Connections and TRS Connections tables on the next page).  
O
I
D
U
A
R
E
T
U
P
M
O
C
B
S
U
6. Secure the faceplate to the junction box using the screws provided (see  
K
M
0
6
1
the figures at right).  
C
P
W
UK Junction Box  
30 mm M3.5  
Screws (2)  
7. Connect the VGA input, audio input, or both.  
Extron  
WPC 160 MK  
1
 

Eiki Projector AH 69601 User Manual
Eizo Computer Monitor L660 User Manual
Extron electronic Car Amplifier DTP HD DA4 4K 230 330 User Manual
Festool Sander ETS 150 3 EQ User Manual
FieldServer Computer Drive FS 8704 16 User Manual
Fisher Price Riding Toy T3857 User Manual
FujiFilm Digital Camera S9500 User Manual
Fujitsu Flat Panel Television PDS4211W H User Manual
Garmin GPS Receiver 174 User Manual
Genius Speaker J10 User Manual