Extron electronic Switch CC AAP Series User Manual

Specifications  
Video input — RGB 580xi AAP / CCS AAP / CCSI AAP  
Number/signaltype .......................... 1 analog RGBHV, RGBS, RGsB, RsGsBs  
Connectors ........................................... 1 15-pin HD female  
User’s Guide  
Video output — RGB 580xi AAP / CCS AAP / CCSI AAP  
Number/signaltype .......................... 1 analog RGBHV, RGBS, RGsB  
Connectors ........................................... 1 15-pin HD female  
General  
Temperature/humidity ..................... Storage -40° to +158°F (-40° to +70°C) / 10%  
to90%,non-condensing  
Operating +32° to +122°F (0° to +50°C) / 10%  
to90%,non-condensing  
Enclosuredimensions  
RGB 580xi AAP/Cable Cubby AAP models (double-height plates)  
Faceplate ................................ 1.4" H x 3.5" W (3.6 cm H x 8.9 cm W)  
Circuit board ......................... 1.3" H x 2.5" W x 0.9" D  
(3.3 cm H x 6.4 cm W x 2.3 cm D) Depth  
excludes connectors and knobs.  
Shippingweight .................................. AAP models . 1 lb (0.5 kg)  
Vibration .............................................. ISTA/NSTA 1A in carton (International Safe  
Transit Association)  
Approvals............................................ UL, CUL, CE, FCC Class A  
MTBF .................................................... 30,000 hours  
Warranty .............................................. 3 years parts and labor  
Specifications are subject to change without notice.  
RGB 580xi AAP/CC AAP Series  
RGB 580xi AAP, RGB 580xi S/CCS AAP,  
RGB 580xi SI/CCSI AAP  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
714.491.1500  
Fax 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
+31.33.453.4040  
Fax +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
+65.6383.4400  
Fax +65.6383.4664  
Extron Electronics, Japan  
Kyodo Building  
16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082 Japan  
+81.3.3511.7655  
Fax +81.3.3511.7656  
68-537-01 Rev. C  
03 06  
© 2006 Extron Electronics. All rights reserved.  
 
Installation and Operation  
Installation and Operation  
Extron’s RGB 580xi AAP double-space devices are designed to  
complement the RGB 580xi remote interface. They may be  
mounted to any Extron product which has an AAP faceplate or to  
an AAP wallplate. See the “AAP Device Part Numbers” and the  
“Cable Cubby AAP Device Part Numbers” sections for AAP/CC  
AAP part numbers.  
Tip (L)  
Sleeve (GND)  
Ring (R)  
Tip (L)  
Sleeve (GND)  
RGB 580xi AAP/CC AAP Series Features  
Audioinputwiring  
3
4
3
Horizontal shift control knob — While viewing the  
displayed image, rotate this control to move the image to  
the right or left on the screen. The power/signal LED will  
flash green whenever the minimum and maximum limits  
of this control are reached.  
4
5
RGB 580xi AAP  
RGB 580xi S AAP  
SHIFT  
AUDIO IN  
COMPUTER IN  
AUDIO IN  
COMPUTER IN  
RGB 580xi  
RGB 580xi  
1
2
1
2
3
4
Input select button — Pressing this button will result in  
contact closure between pins A and B of the contact closure  
control connector on the front panel of the RGB 580xi  
remote interface. This button can also be used for direct  
control of any Extron contact closure-controlled switcher,  
or as a direct connection to an external control system.  
RGB 580xi SI AAP  
SELECT  
SHIFT  
AUDIO IN  
COMPUTER IN  
RGB 580xi  
1
5
2
Mounting the RGB 580xi AAP Device  
4
4
RGB 580xi CCSI AAP  
RGB 580xi CCS AAP  
The AAP device should be cabled before attaching the AAP  
device to a faceplate or wallplate. The screws needed for  
installing an AAP device are built into its front panel, so no  
additional screws will be needed.  
Installation and service must be performed by  
authorized personnel only.  
CAUTION  
1
1
5
1.  
2.  
Connect the output cables to the AAP device’s rear  
connectors. See the section “Cabling the AAP/Cable Cubby  
AAP Device Rear Connectors” in this user’s guide.  
Power/signal LED — This LED lights  
1
amber to indicate that the AAP device is receiving  
power.  
Insert the AAP device’s screws through the holes in the AAP  
double-space faceplate, the AAP wallplate, or the Cable  
Cubby AAP shelf bracket. Secure the AAP device to the  
faceplate/wallplate/shelf bracket with the provided captive  
washers and #4-40 nuts.  
green to indicate that an active sync signal is present at  
the input and the AAP device is receiving power.  
The LED will flash green whenever the minimum and  
maximum limits of the horizontal shift control (H. shift)  
have been reached.  
Computer video input connector — Attach a cable from  
the computer source to this 15-pin HD female connector.  
2
3
Audio input connector — Plug a 3.5 mm stereo plug into  
this jack for unbalanced audio input. Wire the male plug as  
shown in the following illustration.  
RGB 580xi AAP • Installation and Operation  
2
RGB 580xi AAP • Installation and Operation  
3
 
Installation and Operation  
Installation and Operation  
To cable the captive screw connectors, please refer to the  
following diagrams and orient the wires according to the view  
angle of the captive screws. When using Extron’s VGA and  
control cable assembly (see the “Cables” section for part  
numbers), refer to the color of each wire for signal identification.  
Cable  
Clamp  
Control connector (J4) — Insert wires into and tighten the  
screws on this 3.5 mm, 5-pole captive screw connector.  
This connector is used for contact closure and horizontal  
shift signals. Wire the connector as shown below.  
1
AAP 102  
Cable  
2
0
1
P
A
A
IO  
D
U
A
R
TE  
Horizontal shift  
Horizontal shift ground (gray)  
Horizontal shift (brown)  
Contact closure (light blue)  
Contact closure (purple)  
+
(green)  
PU  
M
CO  
P
A
T
C
E
A
P
L
I
IN  
T
S
i
x
0
8
E
S
B
G
R
S
H
RGB 580xi SI AAP  
+
#4-40 Nut w/ Captive  
Washer  
LED connector (J2) — Insert wires into and tighten the  
screws on this 3.5 mm, 3-pole captive screw connector.  
This connector is used for powering the green/amber LED.  
Wire the connector as shown below.  
2
3
Example of mounting an AAP device to a wallplate  
Cabling the AAP/Cable Cubby AAP Device  
Rear Connectors  
Green LED (pink)  
LED ground (yellow)  
Amber LED (orange)  
Extron’s various AAP/Cable Cubby AAP devices for the  
RGB 580xi may come with several rear connectors that may  
require cabling.  
Audio output connector (J3) — Insert wires into and  
tighten the screws on this 3.5 mm, 3-pole captive screw  
connector. This connector is used for unbalanced stereo  
audio output. Wire the connector as shown below.  
Although the control cable, LED, and audio assemblies  
will come prewired (AAP only) to the captive screw  
connectors, any subsequent cable assembly replacement  
will require the following cabling instructions.  
Audio right (red)  
Audio ground (black)  
Audio left (white)  
3
J3  
On Cable Cubby AAP models, the VGA and audio cable  
assemblies will be routed through the Cable Cubby. Refer  
to the Cable Cubby User’s Manual (part #68-701-01) for  
Cable Cubby installation instructions.  
J4  
J2  
Red  
Black  
White  
Lt. Blue  
Purple  
RGB 580xi CCSI AAP  
1
Green  
Gray  
Brown  
2
Yellow  
Pink  
Orange  
Example of AAP device rear connectors  
CC AAP VGA connector  
CC AAP Audio connector  
J4  
1
J2  
2
Cable Cubby  
Example of Cable Cubby AAP device rear connectors  
4
RGB 580xi AAP • Installation and Operation  
RGB 580xi AAP • Installation and Operation  
5
 
Part Numbers  
Part Numbers  
AAP Devices  
Optional RGB 580xi AAP Extension Cables  
These cables only apply to the RGB 580xi AAP,  
RGB 580xi S AAP, and RGB 580xi SI AAP, they do  
not apply to the RGB 580xi CCS AAP or RGB 580xi  
CCSI AAP.  
Description  
Part number  
RGB 580xi AAP 3' (black, white,  
RAL9010 white)  
70-128-02, -03, -05  
70-129-02, -03, -05  
70-134-02, -03, -05  
70-135-02, -03, -05  
70-137-02, -03, -05  
70-138-02, -03, -05  
RGB 580xi AAP 6' (black, white,  
RAL9010 white)  
VGA and control cable assembly  
Part number  
VGA and control cable 3' (0.9 m)  
VGA and control cable 6' (1.8 m)  
VGA and control cable 12' (3.6 m)  
VGA and control cable 25' (7.6 m)  
VGA and control cable 35' (10.6 m)  
VGA and control cable 50' (15.2 m)  
26-521-01  
26-521-02  
26-521-03  
26-521-04  
26-521-05  
26-521-06  
RGB 580xi S AAP 3' (black, white,  
RAL9010 white)  
RGB 580xi S AAP 6' (black, white,  
RAL9010 white)  
RGB 580xi SI AAP 3' (black, white,  
RAL9010 white)  
RGB 580xi SI AAP 6' (black, white,  
RAL9010 white)  
Cable Cubby AAP Devices  
Description  
Part number  
RGB 580xi CCS AAP 9' (black)  
RGB 580xi CCS AAP 12' (black)  
RGB 580xi CCSI AAP 9' (black)  
RGB 580xi CCSI AAP 12' (black)  
70-254-02  
70-255-02  
70-256-02  
70-257-02  
RGB 580xi AAP • Installation and Operation  
6
RGB 580xi AAP • Installation and Operation  
7
 

Fluke Cable Box VR101S User Manual
Ford Automobile FCS 14265 05 User Manual
Frigidaire Washer Dryer FEX831F User Manual
Garland Convection Oven MST45R User Manual
Garland Ventilation Hood GIU 25 User Manual
Garmin Bicycle Accessories 190 00839 08 User Manual
GE Air Conditioner AEL05 User Manual
Gemini CD Player CDX 2400 User Manual
Gemini Portable Speaker GT 1002 User Manual
GE Washer WWA8850R User Manual