Installation and Operation Guide
QC7I Series Water Filters
SELECTING A MOUNTING LOCATION
1. Give consideration to the weight of the unit when operating (filled with water). Operating weights
of the QC7I Systems are:
• Single System - 9 lbs. (4.0 kg.)
• Twin System - 19 lbs. (8.5 kg)
• Triple System - 27 lbs. (12 kg)
• Quad System - 36 lbs. (20 kg)
2. The location should allow for:
• Minimum clearance of 2-1/2” under the cartridge(s) so it can be lowered for removal and
replacement.
Figure 1 – Single System
Figure 2 – Twin System
Figure 3 – Triple System
• Adequate space for “in” and “out” water line connections.
• Be near a drain for flushing and near a 110V outlet if the accessory (sold separately) Everguard
Low Pressure Alarm is used. See Figures 1-8.
3. If used in conjunction with the SR-X feeder, the SR-X should be mounted after the QC7I Series
Filter and as near the equipment as possible. If possible, keep at least 6” available to the left and
the right of the QC7I System in the event poor quality water conditions require the installation of
the optional Everpure E-Series Prefilter.
WARNING: Do not use the MH cartridge in conjunction with the SR-X.
OPERATING SPECIFICATIONS*
Replacement
Combined Model Name
Cartridge
Flow Rate
Capacity
QC7I Single - MC
QC7I Single - MC2
QC7I Single - MH
QC7I Single - MH2
QC7I Single - TO
QC7I Single - CV
QC7I Single - XCV
QC7I Single - XC
QC7I Single - XC2
QC7I Single - 7CB5
QC7I Single - 7CB5-K
QC7I Single - 7CB5-S
MC
MC2
MH
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
1.5 gpm (18.9 lpm)
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
1.67 gpm (6.3 lpm)
2.5 gpm (9.4 lpm)
2.5 gpm (9.4 lpm)
2.5 gpm (9.4 lpm)
9,000 gal (34,000 L)
9,000 gal (34,000 L)
9,000 gal (34,000 L)
9,000 gal (34,000 L)
30,000 gal (113,550 L)
7,500 gal (28,390 L)
10,000 gal (37,850 L)
12,000 gal (45,420 L)
12,000 gal (45,420 L)
10,000 gal (37,850 L)
10,000 gal (37,850 L)
10,000 gal (37,850 L)
MH2
TO
CV
XCV
XC
XC2
7CB5
7CB5-K
7CB5-S
Replacement
Cartridge
Combined Model Name
Flow Rate
Capacity
QC7I Twin - MC
QC7I Twin - MC2
QC7I Twin - MH
QC7I Twin - MH2
QC7I Twin - TO
QC7I Twin - CV
QC7I Twin - XCV
QC7I Twin - XC
MC
MC2
MH
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
3.0 gpm (37.8 lpm)
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
3.3 gpm (12.6 lpm)
5.0 gpm (18.9 lpm)
5.0 gpm (18.9 lpm)
5.0 gpm (18.9 lpm)
18,000 gal (68,000 L)
18,000 gal (68,000 L)
18,000 gal (68,000 L)
18,000 gal (68,000 L)
60,000 gal (227,100 L)
15,000 gal (56,780 L)
20,000 gal (75,700 L)
24,000 gal (90,840 L)
24,000 gal (90,840 L)
20,000 gal (75,700 L)
20,000 gal (75,700 L)
20,000 gal (75,700 L)
MH2
TO
CV
XCV
XC
QC7I Twin - XC2
QC7I Twin - 7CB5
QC7I Twin - 7CB5-K
QC7I Twin - 7CB5-S
XC2
7CB5
7CB5-K
7CB5-S
Figure 4 – Quad System
Manufactured by Everpure
EV3024-87D DE05
CARTRIDGE CHANGE DETERMINATION
Replace cartridges when capacity is reached, or when flow becomes inadequate, but at least annually. All cartridges on multiple cartridge systems should
be changed at the same time. The Everpure Pressure Gauge or Everguard Low Pressure Alarm provides a quick and simple means of determining when the
filter cartridge(s) should be changed. Installed on the outlet port of the filter, the gauge or Everguard LPA can be used to measure both dynamic (flowing) and
static (line) pressure. The cartridge(s) should be changed when the pressure gauge needle is in the red area while equipment is in operation, and yet the
needle shows adequate line pressure between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it
can be assumed that the temporary low-pressure condition was caused by a brief power failure or other incoming pressure disruption.
FLUSHING
For maximum life, all carbon filter cartridges must be flushed for five minutes at full flow before use. ALL NEW CARTRIDGES MUST BE FLUSHED AFTER EACH
CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!
If the cartridges are new, have been properly flushed and both needle and follower register inadequate pressure, or the LPA is sounding, you may be experiencing inadequate
water pressure or some restriction may exist in the inlet water line. In either case, the incoming water pressure must be improved to receive optimum filter life.
COMPLETE CARTRIDGE CHANGE INSTRUCTIONS CAN BE FOUND ON THE FILTER CARTRIDGE LABEL.
Not for residential use. For food service applications only.
PRESSURE GAUGES
Adequate Outlet
Pressure
Low Inlet
Pressure
Adequate Inlet
Pressure
Low Outlet
Pressure
CARTRIDGE CHANGE PROCEDURE
Flushing
4. Pull cartridge downward and out of
Everpure Carbon Filter Cartridge
Change
2. Open flushing valve to relieve
pressure.
head.
6. Turn cartridge right 90˚ until
rotation stops.
8. With flushing valve fully open, open
inlet water at full force for five
minutes. Close flushing valve.
5. Hold head firmly. Align cartridge
lug with label. Insert new cartridge
firmly into head.
1. Shut off power to equipment. Shut
off inlet water ahead of system.
3. Hold head firmly and push upward.
Turn cartridge to left until it stops.
7. Repeat steps 3-6 for remaining
cartridges.
9. Turn on power to equipment
For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed
plumber for installation of the system. This system and its installation must comply with state and local regulations.
REPLACEMENT PARTS
System Tested and Certified by NSF International against
NSF/ANSI Standards 42 and 53 for the reduction of:
Contact your local Everpure dealer for filter cartridges or system
replacement parts.
Standard No. 42 —
Aesthetic Effects
Chemical Reduction
Taste and Odor
Chlorine
Mechanical Filtration
Description
Part Number
EV3114-09
EV3114-09
EV3114-07
EV3114-07
Particulate Class I: 99.2% reduction of particles one-half
Outlet pressure gauge
Inlet pressure gauge (quad system only)
Inlet valve (twin, triple & quad)
Flushing valve
micron and larger in size (MC, MC2, XC, XC2 only)
Standard No. 53 —
Health Effects
Mechanical Filtration (MC, MC2, MH, MH2, XC, XC2 Only)
Turbidity
Cyst
Asbestos
LIMITED WARRANTY
COMMERCIAL WATER TREATMENT EQUIPMENT
You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted against defects in
material and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period commences from the date of purchase
and is administered as follows:
For a period of ONE YEAR
For a period of FIVE YEARS
Replaceable elements (i.e., filter & water treatment cartridges)*
The entire system (excluding replaceable elements)
*This is for material & workmanship, not filter or water treatment cartridge life.
The unit must be used in operating conditions that conform to Everpure’s recommended design guidelines. This warranty will not apply if the unit has been modified, repaired
or altered by someone not authorized by Everpure.
If a part described above is found defective within the specified period, you should notify Everpure technical service at the phone number listed below. Any part
found defective within the terms of this warranty will be repaired or replaced (at Everpure’s discretion) by your local dealer or Everpure technical service. You
pay only freight from our factory and local dealer charges. Any repaired or replaced warranty item will be incorporated under the original warranty terms of the
existing system.
We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone,
chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not
meet Everpure’s specifications. Refer to the specifications section in the Installation and Operating manual for approved application parameters.
Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW, EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT. As a manufacturer, we do not know the characteristics
of your water supply or the purpose for which you are purchasing this product. The quality of water supplies may vary seasonally or over a period of time, and your water
usage rate may vary as well. Water characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for the
determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no
liability and extend no warranties, express or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions for
use described in the owner’s guide or performance data sheet for this product. OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT
(AT EVERPURE’S DISCRETION) OF THE FAILED PARTS OF THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.
Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly,
some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Everpure dealer, or
write Everpure for warranty and service information.
For sales, replacement components, and service, contact your Everpure dealer or:
Everpure, LLC: 1040 Muirfield Drive • Hanover Park, Illinois 60133 • 800.323.7873
In Europe: Toekomstlaan 30 • B-2200 Herentals, Belguim
Technical Service
800.942.1153
In Japan: Hashimoto MN Bldg. 7F • 3-25-1 Hashimoto Sagamihara-Shi • Kanagawa 229-1103, Japan
Printed in U.S.A.
EV3024-87D DE05
|