Edelbrock Automobile Parts 1565 User Manual

EDELBROCK/BILLET SPECIALTIES TRU TRAC PULLEY SYSTEM  
for use with Edelbrock Superchargers  
Catalog #1565 & #1566  
®
INSTALLATION INSTRUCTIONS  
Please study these instructions carefully before installing your new Tru Trac Pulley System. If you have any questions or problems, do not  
hesitate to contact our Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time or e-  
mail us at: [email protected].  
DESCRIPTION: The Edelbrock Tru Trac Pulley System is a complete front end accessory kit that is designed specifically for use with Edelbrock  
Superchargers offered as part #15611, #15621, #15631, #15641, and the Edelbrock supercharged crate engine #46700. Kit #1565 includes a  
power steering pump while kit #1566 does not. Please consult the Billet Specialties instructions included with this kit before beginning  
installation.  
IMPORTANT NOTE:  
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor  
performance and engine or vehicle damage.  
INSTALLATION INSTRUCTIONS  
NOTE: The Edelbrock/Billet Specialties Tru Trac Pulley System is  
intended for use with Edelbrock Superchargers only. The use of these  
parts in any other application is not recommended or supported. The  
following instructions should be used in place of steps #10 & #11 of the  
supercharger installation instructions.  
1. Assemble the snout support, bridge bracket, and idler pulleys.  
Attach the snout support to the bracket using the supplied M8  
x 1.25 x 16mm long bolts. Attach the idler pulleys to the  
bracket using the supplied M10 x 1.0 x 45mm long bolts.  
Tighten the idler pulley bolts, but do not fully tighten the snout  
support bolts at this time (See Figure 1).  
Figure 1  
2. Install the Tru Trac Pulley System according to the  
instructions provided by Billet Specialties using the hardware  
supplied as specified. Refer to Figure 2, and the  
instructions supplied by Billet Specialties for the proper  
bridge bracket installation procedure. Please note that the  
bridge bracket in this kit has been modified to accomodate  
the supercharger but the installation procedure remains  
unchanged.  
NOTE:  
For Kit  
#1566 route  
the belt as  
pictured to  
the left;  
Figure 2  
following  
the white  
dotted line.  
3. Continue installing your Tru Trac Pulley System. When  
finished, adjust the snout support so that it contacts the  
supercharger snout, and tighten the snout support bolts.  
Belt routing for Edelbrock/Billet Specialties Tru Trac Pulley System #1565  
(w/ power steering pump)  
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503  
Tech-Line: (800) 416-8628 • E-Mail: [email protected]  
Edelbrock Snout Support and Pulley Kit  
Rev. 11/07 - AJ/mc  
©2007 Edelbrock Corporation  
Brochure #63-1565  
Page 1 of 1  
 

Dyson Vacuum Cleaner DC19 User Manual
Eizo Computer Monitor HD 2411W User Manual
Fellowes Laminator SPL 125 User Manual
Focal Car Speaker 165 KRX2 User Manual
Gaggenau Cooktop CK 260 604 User Manual
Gemini Musical Instrument Mixer User Manual
GE Monogram Dishwasher ZBD4900YSS User Manual
GE Monogram Ventilation Hood ZV925SL User Manual
Gentek Speaker SPKE4 User Manual
Goodman Mfg Gas Heater GPG13 User Manual