User’s Manual
MPA 122
Mini Power Amplifier
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
68-943-01 Rev. A
11 04
714.491.1500
+31.33.453.4040
+65.6383.4400
Fax 714.491.1517
Fax +31.33.453.4050
Fax +65.6383.4664
Fax +81.3.3511.7656
© 2004 Extron Electronics. All rights reserved.
Quick Start Guide — MPA 122
To install and set up an MPA 122 Mini Power Amplifier, follow these steps:
Step 1
Turn all of the equipment off and disconnect it from the power
source.
Step 2
Mount the MPA 122 on a rack, under a desk, or on a projector, as
illustrated below.
Extron
Projector Mounting
Bracket
Extron
MPA 122
Mini Power
Amplifier
S
R
E
R
E
T
K
U
A
M
V
E
/
P
L
T S
A
S
L
O
V
Extron
s
0
P U
m
h
1
2 2
T
U
O
T E
1
O
/ 8
4
R
M P
M O
L
S
U S
C
R
Power Supply
T S
U
L
I N P
E R
W
P O
Plastic Tie
Under Desk
Projector Mount
DISTR
IB
UT
ION
AM
PL
IFIER
D
IST
VersaTools Rack Shelf
RIB
U
T
ION
A
MP
L
IFIER
1/4 Rack Width False Front
Face Plate
DIS
T
R
IB
UTION
AMPL
Use 2 mounting holes on
opposite corners
IFIER
(2) 4-40 x 3/16" screws
Rack Mount
Step 3
Attach the speakers to the MPA 122.
Step 4
Attach inputs to the MPA 122 unit and the audio source and/or
projector. Ensure that the projector’s audio output is set to variable
out. Multiple input options (RCA, 3.5 mm stereo input, or captive
screw) can be used simultaneously; this will result in audio mixing.
See Inputs in chapter 2 for more information on these audio
connections.
Step 5
Connect power cords to MPA 122 and other audio equipment.
MPA 122 • Quick Start Guide QS-1
Table of Contents
Quick Start Guide — MPA 122, cont’d
Chapter 1 • Introduction .......................................................... 1-1
About this Manual ................................................................ 1-2
About the MPA 122............................................................... 1-2
Features ...................................................................................... 1-2
Step 6
Adjust the MPA 122 input level, bass and treble.
a. If connecting to a projector, ensure that the volume on the device
is at its lowest point, then adjust the level of the MPA 122 fully
counterclockwise.
LEVEL
BASS
TREBLE
b. Set the projector volume to its maximum
volume level (no sound should come
out).
Chapter 2 • Installation and Operation......................... 2-1
Installation Overview.......................................................... 2-2
MPA 122
MINI POWER AMPLIFIER
Mounting the MPA 122....................................................... 2-2
Rack mounting....................................................................... 2-3
Under-desk mounting ........................................................... 2-4
Projector mounting ............................................................... 2-5
c. Return to the MPA 122 and raise the level until sound distortion
occurs, then lower slightly until distortion disappears. This
setting ensures that, whatever the projector volume setting may
be, no clipping occurs.
d. Adjust bass and treble to preference.
Rear Panel Features.............................................................. 2-6
Power input ........................................................................... 2-7
Audio inputs .......................................................................... 2-7
Remote control ...................................................................... 2-8
Audio output ......................................................................... 2-8
8 ohm Ceiling
Speakers
in Parallel
PC
DVD
VGA w/
Audio Cable
Audio RCA
S-video
Front Panel Features ............................................................ 2-8
2
2
1
A
P
S
T
M
U
P
T
U
O
4/8 Ohms
S
U
Setting Up the MPA 122 Amplifier ............................... 2-9
C
TE
R
O
S
T
EM
V
U
R
P
L
IN
TE
10
/MU
L
O
V
R
L
L
R
E
W
Remote connector wiring ................................................... 2-10
O
P
Extron
R
VCR
MPA 122
Mini Power Amplifier
Composite
Audio RCA
Chapter 3 • Remote Operation ............................................ 3-1
Remote Control Options .................................................... 3-2
Variable
Audio
Output
1
2
R
O
ECT
OJ
PR
FF
O
3
4
ON
E
ComLink
UM
L
O
V
IG
F
N
O
Appendix A • Specifications, Part Numbers,
C
4
IP
10
LC
M
E
UT
M
P
U
L
VO
VCM 100 AA
and Accessories.............................................................................. A-1
2
Extron
MLC 104 IP
Controller
Extron
Specifications ......................................................................... A-2
Included Parts......................................................................... A-5
Optional Accessories........................................................... A-5
Projector
3
VCM 100 AAP
Volume/Mute Controller
1
Remote Control Options
IR Remote
IR Remote - (input selection and volume control through projector)
VCM 100 Volume/Mute Controller - (direct MPA 122 control)
1
2
3
MLC 104 IP Controller - (input selection and volume control through projector)
Typical connection setup
MPA 122
OUTPUTS
4/8 Ohms
INPUTS
C
US
L
POWER
REMOTE
All trademarks mentioned in this manual are the properties of their respective owners.
R
10V
VOL/MUTE
R
L
12V
3A MAX
R
L
68-943-01 Rev. A
11 04
The Extron MPA 122 mini power amplifier
MPA 122 • Quick Start Guide
QS-2
MPA 122 • Table of Contents
iii
Table of Contents, cont’d
MPA 122
Chapter One
1
Introduction
About this Manual
About the MPA 122
Features
MPA 122 • Table of Contents
iv
Introduction
Volume and mute remote control — The MPA 122 can be
remotely controlled for volume adjustment and muting
via connectivity to a rear panel, captive screw “Remote”
input connector.
About this Manual
This manual contains information about the Extron MPA 122
Mini Power Amplifier with instructions on how to mount and
operate the unit.
Flexible mounting options — The MPA 122 can be mounted on
a rack, projector, or under furniture.
About the MPA 122
External international power supply — The autoswitchable,
12 VDC, 3 A external power supply provides worldwide
power compatibility (part #70-380-01).
The Extron MPA 122 Mini Power Amplifier provides 2-channel
power amplification for speaker systems in applications
requiring compact, economical audio solutions. The MPA 122
delivers 11 watts (rms) per channel into 4 ohms and
7 watts (rms) into 8 ohms. It is optimized for driving four 8
ohm ceiling speakers, two in parallel, per channel.
The MPA 122 accepts balanced and unbalanced stereo inputs,
and provides outputs as stereo or dual mono audio signals.
Front panel controls are provided for input level, bass, and
treble. The front panel also features switches for stereo/dual
mono operation and a limiter switch which automatically
reduces the gain to prevent distortion (amplifier clipping). The
MPA 122 features remote control capability for volume
adjustment and muting. As part of the VersaTools® line, the
MPA 122 can be housed in a 1U, quarter rack width metal
enclosure, mounted under a desk, or mounted on a projector.
Features
Digital audio amplifier — The MPA 122 features improved,
class D technology for high efficiency and low distortion.
Compact size — The MPA 122 is housed in a 1U high, 1/4 rack
width, 3" deep, metal enclosure, making this amplifier a
powerful product for many unique applications.
Balanced and unbalanced audio inputs — Balanced or
unbalanced stereo input is on a captive screw connector.
The MPA 122 also includes RCA connectors and a 3.5 mm
stereo mini jack for unbalanced input.
Quick plug speaker outputs — Speaker output is on a captive
screw connector for quick installation.
Front panel controls — Input level, bass, and treble can be
easily adjusted from the front panel.
Limiter switch — The limiter switch prevents output distortion
(clipping) and potential damage to speakers.
Stereo/dual mono switch — Fits applications for both stereo
program speakers or mono ceiling speakers.
1-3
MPA 122 • Introduction
1-2
MPA 122 • Introduction
Introduction
MPA 122
Chapter Two
2
Installation and Operation
Installation Overview
Mounting the MPA 122
Rear Panel Features
Front Panel Features
Setting up the MPA 122 Amplifier
MPA 122 • Introduction
1-4
Installation and Operation
Installation Overview
Rack mounting
To install and set up an MPA 122, follow these steps:
1.
If feet were previously installed on the bottom of the
MPA 122 unit, remove them.
Turn all of the equipment off. Make sure that the input
devices (DVD, VCR, PC, etc.), the MPA 122 unit, and the
output devices are turned off and disconnected from their
power source(s).
1
2.
Mount the unit on the rack shelf, using two
4-40 x 3/16" screws in opposite (diagonal) corners to
secure the MPA to the shelf.
3.
Install blank panel(s) or other unit(s) to the rack shelf.
Mount the MPA 122 unit. See Mounting the MPA 122
below.
2
3
4.
Insert the shelf into the rack, aligning the holes in the shelf
with those in the rack.
Attach the speakers and/or other output devices to the
MPA 122. See Rear Panel Features later in this chapter for
more information.
5.
Secure the shelf to the rack using the supplied machine
screws.
Attach inputs to the MPA 122. See Inputs later in this
chapter for more information.
4
Connect power cords to the MPA 122 and other devices.
5
6
Adjust MPA 122 input level, bass and treble. See Setting
up the MPA Amplifier later in this chapter for detailed
information.
DISTRIB
U
TION AMPLIFIER
DISTRIB
VersaTools Rack Shelf
1/4 Rack Width False Front
UTION AMPLIFIER
Mounting the MPA 122
There are many optional accessories for mounting the MPA 122.
They include the following:
Face Plate
•
VersaTools® multi-product projector mounting kit
(part #70-374-01)
DISTRIB
U
Use 2 mounting holes on
opposite corners
TION AMPL
IFIER
(2) 4-40 x 3/16" screws
•
•
•
•
•
•
•
1U universal VersaTools rack shelf
1U basic VersaTools rack shelf
1U universal rack shelf
(part #60-190-20)
(part #60-604-20)
(part #60-190-01)
(part #60-190-10)
(part #60-604-01)
(part #60-604-10)
Figure 2-1 — Mounting the MPA 122 on the
VersaTools® shelf
Only products in the VersaTools® or IP Link lines can be
mounted to a VersaTools shelf.
1U 6" deep universal rack shelf kit
1U basic rack shelf
1U 6" deep basic rack shelf
Mini under-desk mounting bracket kit
(part #70-212-01)
Following are detailed instructions on rack mounting, under-
desk mounting, and projector mounting the MPA 122 unit (for
use in classrooms, personal offices, meeting rooms, etc.).
MPA 122 • Installation and Operation
MPA 122 • Installation and Operation
2-2
2-3
Installation and operation, cont’d
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
1/4 Rack Width Front False
Faceplate
Both front false faceplates
use 2 screws.
Figure 2-3 — Under-desk mounting
Projector mounting
In addition to mounting the MPA 122 unit to a rack or under
furniture, it can also be projector mounted using the optional
VersaTools® multi-product projector mounting kit
(part #70-374-01).
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Figure 2-2 — Mounting the MPA 122 on the
standard shelf
Only VersaTools products and most IP Link products
can be mounted using the multi-product projector
mounting kit.
Under-desk mounting
In addition to using the MPA 122 unit on a rack or projector, it
can also be mounted under furniture (or under a desk). Mount
the unit by using the optional mounting kit (Extron part #70-
212-01) for furniture, as follows:
To projector mount the MPA 122, do the following:
1.
If necessary, remove the feet from the bottom of the device
to be installed.
1.
2.
3.
Attach the mounting brackets to the amplifier with the
machine screws provided (figure 2-3).
2.
Mount the MPA 122 to one of the bracket’s three mounting
plates. The device can be vertically mounted facing either
up or down, whichever is most convenient. See the
illustration below.
If feet were previously installed on the bottom of the
interface, remove them.
Hold the amplifier with the attached brackets against the
underside of the table or other furniture. Mark the
location of the screw holes of the bracket on the mounting
surface.
Use two supplied 4-40 x 3/16 screws in opposite
(diagonal) corners to secure the device to the bracket.
Rubber Pad
4.
5.
6.
7.
Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked screw
locations.
Multi Product
Projector Mounting Kit
U-Bolt
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until just less than
1/4" of the screw head protrudes.
Align the mounting screws with the slots in the brackets
and place the interface against the surface, with the
screws through the bracket slots.
Slide the unit slightly forward or back, then tighten all
four screws to secure it in place.
Figure 2-4 — Projector mounting for the MPA 122
MPA 122 • Installation and Operation
2-4
MPA 122 • Installation and Operation
2-5
Installation and operation, cont’d
Power input
On the side mounting plates, devices are typically
mounted on the outside of the bracket. On the front
mounting plate, devices are typically mounted on the
inside of the bracket.
Power connection — Plug the external 12 VDC power
supply into this connector. The power supply is included
with the unit.
1
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
The front mounting plate is 1/4" taller than the side
plates. This size helps ensure the accessibility of buttons
or connectors.
When connecting the power supply, voltage polarity
is extremely important. Applying power with
incorrect voltage polarity could damage the power
supply and the interface. Identify the power cord
negative lead by the ridges on the side of the cord.
CAUTION
3.
4.
Affix the black rubber pad to the mounting plate.
Place the U-bolt around the ceiling pole and insert the two
legs of the U-bolt through the slotted holes on the
bracket’s mounting plate and then through the slotted
holes on the backing brace.
Smooth
Ridges
For a typical (1.5" to 2.0" diameter) pole — The supplied
U-bolt fits a typical ceiling pole.
A
A
SECTION A–A
For a smaller or larger pole — Locally obtain a U-bolt that
fits the ceiling pole. The slotted holes on the bracket will
accommodate a U-bolt for pole sizes from 1.0" to 2.5" in
diameter.
0.2” (5 mm) MAX
Power Supply
Output Cord
Captive Screw
Connector
5.
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers.
Figure 2-6 — Power connector wiring
Do not tin the stripped power supply leads before
Rear Panel Features
installing the captive screw connector. Tinned wires are
not as secure in the captive screw connectors and could
pull out.
MPA 122
OUTPUTS
4/8 Ohms
INPUTS
C
US
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before continuing.
L
POWER
REMOTE
R
12V
3A MAX
10V
VOL/MUTE
L
L
R
R
Audio inputs
There are three choices of input connectors (RCA, 3.5 mm
stereo, and captive screw) available on the rear panel for
adapter-free connections.
1
2
3
4
5
6
Figure 2-5 — MPA 122 back panel
Connecting more than one input signal at one time will result in
audio mixing.
RCA input connector — Plug an RCA audio source to this line
level input.
2
3
3.5 mm stereo input — Plug a 3.5 mm audio micro cable into
this stereo jack.
MPA 122 • Installation and Operation
2-6
MPA 122 • Installation and Operation
2-7
Installation and operation, cont’d
Balanced or unbalanced audio input connector — Marked “L”
and “R”, this 3.5 mm captive screw input is for bare wire,
balanced or unbalanced audio signals.
Power LED — A green LED lights to indicate that the unit is
receiving power.
4
1
2
DIP switches — This 2-bank DIP switch controls the limiter (on
and off) on one side, and allows for setting the Stereo and Dual
Mono modes on the other.
Tip
Ring
Tip
Sleeve (s)
Tip
Sleeve
Tip
Ring
1 — Limiter — When the limiter is switched to on, the MPA will
automatically reduce the level to prevent the amplifier
from clipping.
Balanced Input
Unbalanced Input
Figure 2-7 — 3.5 mm captive screw audio input
connector wiring
2 — Stereo/Dual Mono:
Stereo mode — In stereo mode, the audio signal input from
each channel will be output to the speakers respectively.
Remote control
Dual Mono mode — In dual mono mode, the inputs from
channels L and R will be summed together and output to
the speakers as two mono channels. In essence, output L
and R contain the same combined signal information.
Remote input connector — An optional 3-pin captive screw
5
connector that allows a wall mounted audio controller or
MediaLink product to remotely control volume and mute levels
for the MPA 122 unit.
3
Potentiometer adjustments — These three potentiometers
optimize level, bass, and treble adjustments.
For more information on using the remote input connector, see
Chapter 3, Remote Operation.
Setting Up the MPA 122 Amplifier
Audio output
The following steps ensure optimal sound by adjusting the
projector volume to match the level, bass, and treble of the
MPA 122 amplifier.
Speaker connector — Marked “L” and “R”, this 4-pin, 5 mm
captive screw connector is used to connect the amplifier to the
speakers.
6
When setting up volume control, ensure that the projector
output is set to variable out. Consult the projector’s user
manual for detailed instructions on its calibration.
The recommended MPA 122 output set-up includes 4
ceiling speakers of 8 ohm impedance, (2 sets in parallel
with each other), so that each output drives a maximum
of 4 ohm loads.
To adjust the MPA 122 input level, bass, and treble, do the
following:
Do not tie both L and R outputs to each other and/
or to input ground. Doing so will short out the
outputs and damage the amplifier.
1.
If connecting to a projector, ensure that the volume on the
device is at its lowest point, then adjust the level of the
MPA 122 fully counterclockwise.
2.
3.
Set the projector volume to its maximum volume level.
No sound should come out.
Front Panel Features
Return to the MPA and raise the level until sound
distortion occurs, then lower the level slightly until any
distortion disappears. This setting ensures that, whatever
the projector volume setting may be, no clipping occurs.
LEVEL
BASS
TREBLE
ON
STEREO
LIMITER
1
DUAL
4.
Adjust bass and treble to preference.
MPA 122
OFF
MONO
MINI POWER AMPLIFIER
2
3
Figure 2-8 — MPA 122 front panel
MPA 122 • Installation and Operation
2-8
MPA 122 • Installation and Operation
2-9
Installation and operation, cont’d
Remote connector wiring
MPA 122
As shown below, Pin 1 is 10 VDC reference voltage. Pin 2 is
volume control DC voltage; range is 0 to 10 V, where 0 V is mute
and 10 V provides maximum volume. Pin 3 is ground.
All nominal levels are at 10%
REMOTE
1
2
3
10V
VOL/MUTE
1
2
MAX
10K
MIN
MUTE
2K
VOLUME
3
GND
Figure 2-9 — Pinout diagram for optional remote
connector
Chapter Three
See Chapter 3, Remote Operation for more information on the
three options (IR remote, MLC series, or DC volume/mute
controller) for remote control.
3
Remote Operation
Remote Control Options
MPA 122 • Installation and Operation
2-10
Remote Operation
Remote Control Options
MPA 122
8 ohm Ceiling
Speakers
in Parallel
PC
DVD
VGA w/
S-video
Audio Cable
Audio RCA
2
2
1
A
P
S
T
M
U
P
T
U
O
4/8 Ohms
S
U
C
TE
R
O
S
T
EM
V
U
R
P
L
IN
TE
U
10
/M
L
VO
R
L
L
R
E
W
O
P
Extron
MPA 122
Mini Power Amplifier
R
VCR
Composite
Audio RCA
Variable
Audio
Output
1
R
O
T
2
C
E
OJ
PR
FF
O
3
4
ON
E
ComLink
UM
OL
V
IG
F
N
O
C
104 IP
LC
M
TE
U
M
P
E
L
VO
VCM 100 AA
2
Extron
MLC 104 IP
Controller
Extron
Projector
3
VCM 100 AAP
Volume/Mute Controller
1
Remote Control Options
IR Remote
Appendix A
IR Remote - (input selection and volume control through projector)
VCM 100 Volume/Mute Controller - (direct MPA 122 control)
1
2
3
MLC 104 IP Controller - (input selection and volume control through projector)
A
Figure 3-1 — Three remote control options
Using the projector’s IR remote — For a projector with variable
audio outputs, use the projector’s IR remote to control the
projector’s volume, which effectively controls the MPA’s
volume.
1
2
3
Specifications, Part Numbers,
and Accessories
Extron VCM 100 or mute controller — For a projector without
variable audio outputs, or for a system designed to control MPA
volume directly, use a 10k ohm potentiometer to control the
MPA directly via the remote port on the MPA.
Specifications
Included Parts
Using a MediaLink™ Controller — For a projector with
variable audio output, use a MediaLink controller to control the
projector’s volume via RS-232 or the projector’s IR remote to
effectively control the MPA volume.
Optional Accessories
MPA 122 • Remote Operation
3-2
Specifications, Part Numbers, and Accessories
Audio
Audio output
Frequency response..................... 20 Hz to 20 kHz, 1 dB @ 1 watt output
THD + Noise ................................ 0.15% @ 1 kHz at nominal level (1 watt,
8 ohm load)
Number/signal type ................... 1 stereo or 2 mono (2 channels total)
Connectors .................................... (1) 5 mm captive screw connector, 4 pole
Minimum load impedance ......... 4 ohms
S/N ................................................ >72 dB @ 20 Hz to 20 kHz at maximum
output (unweighted)
Stereo channel separation .......... >55 dB @ 1 kHz, >45 dB @ 20 kHz
CMRR ............................................ >80 dB @ 1 kHz, >70 dB @ 20 kHz
Bass adjustment ........................... 10 dB @ 80 Hz (reference) to 1 kHz (2 dB
tolerance)
Amplifier type .............................. Improved Class D
Continuous power with a full load and 1% THD
At 4 ohms .......................... 11 watts (rms) per channel
At 8 ohms .......................... 7 watts (rms) per channel
Damping factor ............................ >30 (with a 4 ohm load)
Treble adjustment ........................ 10 dB @ 10 kHz (reference) to 1 kHz (2
dB tolerance)
Control/remote — amplifier
Control port .................................. (1) 3.5 mm captive screw connector, 3 pole
Pin configuration ........................... Pin 1 = 10 V, pin 2 = variable voltage or
mute, pin 3 = GND
Audio input
Number/signal type ................... 1 stereo, balanced/unbalanced input
2 stereo, unbalanced inputs
General
(The three inputs are individually
buffered and mixed together.)
External power supply ............... 100 VAC to 240 VAC, 50/60 Hz, external,
autoswitchable; to 12 VDC, 3 A (max.),
regulated
Power input requirements ......... 12 VDC, up to 3 A
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Connectors .................................... (1) 3.5 mm captive screw connector, 5 pole
(main input)
(1) 3.5 mm mini audio jack (tip, ring,
sleeve)
1 pair RCA
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Impedance .................................... >18k ohms unbalanced, >24k ohms
balanced, DC coupled
Rack mount................................... Yes, with optional 1U rack shelf, part #60-
190-01 or 60-604-01; or VersaTools® rack
shelf, part #60-190-20 or 60-604-20. Above-
projector mountable with optional Multi-
Product Projector Mounting Kit #70-374-
01. Also furniture mountable with
Nominal level ............................... +4 dBu (1.23 Vrms) balanced or -10 dBV
(316 mVrms) unbalanced
Maximum level
Level pot. at 12 o’clock.... +6 dBV (unbalanced), +16 dBu (balanced)
at 1% THD+N
Level pot. at 9 o’clock...... +16 dBV (unbalanced), +23 dBu (balanced)
at 1% THD+N
optional Mini Under-Desk Mounting Kit,
#70-212-01.
Input level sensitivity ................. -10 dBV (316 mV) from unbalanced input
for maximum output (11 watts with a
Enclosure type.............................. Metal
Enclosure dimensions ................. 1.7" H x 4.3" W x 3.0" D (1U high, quarter
rack wide)
4 ohm load and level set to maximum)
before clipping
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight............................. 0.6 lbs (0.3 kg)
Shipping weight........................... 3 lbs (2 kg)
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Vibration ....................................... ISTA 1A in carton (International Safe
Transit Association)
MPA 122 • Specifications, Part Numbers, and Accessories
A-2
MPA 122 • Specifications, Part Numbers, and Accessories
A-3
Specifications, Part Numbers, and Accessories
Listings .......................................... UL, CUL
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Included Parts
These items are included in each order of a MPA 122 unit:
Warranty ....................................... 3 years parts and labor
Included parts
Part number
All nominal levels are at 10%
MPA 122 Mini Power Amplifier
60-668-01
70-380-01
10-319-10
12 VDC, 3 A external power supply
Female, 3.5 mm, 5-pole captive screw conn.
Specifications are subject to change without notice.
Female, 3.5 mm, 3-pole captive screw conn. 10-319-03
MPA 122 Mini Power Amplifier User’s Manual
4-pin, 5 mm terminal block plug
Black rubber pad
10-163-14
IEC power cord
Industrial strength Velcro®
Optional Accessories
Accessories
Part number
VersaTools® multi-product projector mounting kit
70-374-01
1U universal VersaTools rack shelf
1U basic VersaTools rack shelf
1U universal rack shelf
60-190-20
60-604-20
60-190-01
60-190-10
60-604-01
60-604-10
70-212-01
1U 6" deep universal rack shelf kit
1U basic rack shelf
1U 6" deep basic rack shelf
Mini under-desk mounting bracket kit
MPA 122 • Specifications, Part Numbers, and Accessories
A-4
MPA 122 • Specifications, Part Numbers, and Accessories
A-5
Specifications, Part Numbers, Accessories, cont’d
MPA 122 • Specifications, Part Numbers, and Accessories
A-6
|