EVF-1152D/64-FG
Single 15” Two-Way
60° x 40° Full-Range
Fully-Weatherized
Loudspeaker System
Key Features:
•
•
•
•
•
Fully-weatherized fiberglass finish with gland nut
and stainless-steel grille
DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit
pure titanium compression driver
DVX3151A 15” (381 mm) LF transducer with fully
symmetric drive
Advanced fourth-order crossover network with
HF protection
Coverage pattern: 60° x 40° Constant
DirectivityTM 12” rotatable waveguide
•
•
•
100 dB sensitivity, 134 dB maximum SPL
System rating: 600 W continuous, 2400 W peak
Active rating: LF 500 W/HF 75 W continuous
(2000 W/300 W peak)
Technical Specifications:
Freq. Response1 (-3 dB): 107 Hz - 18 kHz
Freq. Range1 (-10 dB): 58 Hz - 21 kHz
•
(22) M10 threaded suspension points
Rotatable Coverage: 60° x 40°
Rec. High-Pass Frequency: 55 Hz
General Description:
Passive Crossover Freq.: 1300 Hz
Axial Sensitivity1: 100 dB (1 W/1 m)
The Electro-Voice EVF-1152D/64-FG is a fully-weatherized, fiber-
glass-coated, high-power, two-way loudspeaker system that can be
used in a variety of applications where high-quality sound reinforce-
ment is required in a compact, lightweight package.
Max. Calculated SPL1: 134 dB
Passive Power Handling2: 600 W continuous, 2400 W peak
Impedance: 8 ohms (nominal), 6.0 ohms (min.)
LF Transducer - DVX3151A, 15” (381 mm) driver
LF Axial Sensitivity4: 100 dB (1 W/1 m)
The EVF-1152D/64-FG utilizes the DH7N, a high-output 3” titanium
compression driver, coupled to a Constant Directivity™ 60° x 40°
waveguide. The DVX3151A 15” woofer was developed using FEA
optimization for motor, suspension, and electrical design to ensure
very low distortion, high efficiency, and maximum intelligibility at high
SPL. The crossover uses steep, 24-dB-per-octave slopes with equal-
ization for very smooth response in the vocal range, linear off-axis
response, and a protection circuit for long-term reliability.
LF Max. Calculated SPL: 133 dB
LF Power Handling3: 500 W continuous, 2000 W peak
LF Impedance: 8 ohms (nominal), 7.2 ohms (min.)
HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver
HF Axial Sensitivity4: 113 dB (1 W/1 m)
HF Max. Calculated SPL: 138 dB
The EVF-1152D/64-FG’s features make it ideal for many fixed-install
applications, including applications with full exposure to outdoor
elements. The trapezoidal enclosure is constructed of weather-resis-
tant birch, and coated with fiberglass for maximum protection from
extreme outdoor elements. The unique acoustic and rigging design
allows for vertical and horizontal clusters to be built using any
combination of loudspeakers from the entire EVF and EVH series.
With seven horn patterns to choose from, along with an assortment
of low-frequency and subwoofer loudspeakers, you have the tools to
maximize flexibility of system design, no matter what the application
and budget. The innovative input panel provides a choice of Phoenix-
style connector (included in all standard models) or the ability to add
a dual NL4-type connector cover plate or gland-nut cover plate (for
weatherizing applications). An externally accessible jumper selects
passive or active operation. An available 70.7/100-V transformer
kit may be easily mounted to the input panel for use in distributed
systems. All these features give you the flexibility to address a large
range of venues, quickly and precisely supporting customer require-
ments with fewer items in inventory.
HF Power Handling3: 75 W continuous, 300 W peak
HF Impedance: 8 ohms (nominal), 6.0 ohms (min.)
Connectors: Dual four-pin 10 AWG Phoenix/Euro Block
screw-terminals, CDG dual-gland-nut input
panel cover included for weatherizing
Enclosure: 13-ply weather-resistant birch with fiberglass
finish
Grille: 18 GA stainless steel with hydrophobic cloth
Environmental: IEC 60529 IP55
Suspension: (22) M10 threaded suspension points
Dimensions 30.26” x 18.50” x 18.37”
(H x W x D): (768.6 mm x 469.8 mm x 466.6 mm)
Weight: 75.7 lb (34.4 kg) net, 86.0 lb (39.1 kg) shipping
1 Half-space measurement.
3 AES 2-1984, tested for eight hours.
4 Arithmetic averages, 300 - 1,300 Hz (LF) and
1,300 - 5,000 Hz (HF).
2 EIA RS-426A, tested for eight hours.
Engineering Data Sheet
Polar Plots (1/3 Octave):
400 Hz
500 Hz
1.25 kHz
3.15 kHz
8 kHz
630 Hz
800 Hz
1 kHz
2.5 kHz
6.3 kHz
16 kHz
1.6 kHz
2 kHz
4 kHz
5 kHz
12.5 kHz
10 kHz
20 kHz
Horizontal = Black
Vertical = Grey
Dimension Drawings:
End View
Front View
Side View
Rear View
EVF-1152D/64 Part Numbers
• PRD000295-001 EVF-1152D/64-BLK, 60° x 40°, black finish
• PRD000295-002 EVF-1152D/64-WHT, 60° x 40°, white finish
• PRD000295-003 EVF-1152D/64-PIB, 60° x 40°, black finish,
weather resistant
• PRD000295-004 EVF-1152D/64-PIW, 60° x 40°, white finish,
weather resistant
• PRD000295-005 EVF-1152D/64-FGB, 60° x 40°, black finish,
weather resistant fiberglass
• PRD000295-006 EVF-1152D/64-FGW, 60° x 40°, white finish,
weather resistant fiberglass
CAUTION
This EVF loudspeaker should be suspended overhead only
in accordance with the procedures and limitations
specified in the EVF/EVH User Manual and possible
manual update notices. This system should be suspended
with certified rigging hardware by an authorized rigging
professional and in compliance with local, state, and
federal overhead suspension ordinances.
Performance Match
Accessories
• PRD000288
• PRD000289
• PRD000290
• PRD000291
• PRD000292
• PRD000293
• PRD000294
• PRD000296
• PRD000297
• PRD000298
• PRD000299
• PRD000300
• PRD000302
• CPS2.9 120V
• CPS2.12 120V
• D170469
EVF-1122D/64, 60° x 40° coverage
EVF-1122D/66, 60° x 60° coverage
EVF-1122D/94, 90° x 40° coverage
EVF-1122D/96, 90° x 60° coverage
EVF-1122D/99, 90° x 90° coverage
EVF-1122D/126, 120° x 60° coverage
EVF-1152D/43, 40° x 30° coverage
EVF-1152D/66, 60° x 60° coverage
EVF-1152D/94, 90° x 40° coverage
EVF-1152D/96, 90° x 60° coverage
EVF-1152D/99, 90° x 90° coverage
EVF-2121S, dual 12” bass element
EVF-2151D, dual 15” bass element
CPS2.9, 120V power amplifier, 2 x 900W
CPS2.12, 120V power amplifier, 2 x 1200W
CPS4.5, 120V power amplifier, 4 x 500W
CPS4.10, 120V power amplifier, 4 x 1000W
• ACC000084-000 CDNL4, cover plate, dual NL4
• ACC000085-000 CSG, cover plate, single gland nut
• ACC000086-000 CDG, cover plate, dual gland nut
• ACC000087-000 TK-150, 70V transformer, 150W
• ACC000089-001 HRK-1B, horiz. rigging kit, EVF, black
• ACC000089-002 HRK-1W, horiz. rigging kit, EVF, white
• ACC000090-001 HRK-2B, horiz. rigging kit, EVF-SUB, black
• ACC000090-002 HRK-2W, horiz. rigging kit, EVF-SUB, white
• ACC000091-001 HRK-3B, horiz. rigging kit, EVH, black
• ACC000091-002 HRK-3W, horiz. rigging kit, EVH, white
• ACC000092-001 VRK-1B, vert. rigging kit, EVF, black
• ACC000092-002 VRK-1W, vert. rigging kit, EVF, white
• ACC000093-001 VRK-2B, vert. rigging kit, EVF-SUB, black
• ACC000093-002 VRK-2W, vert. rigging kit, EVF-SUB, white
• ACC000094-001 VRK-3B, vert. rigging kit, EVH, black
• ACC000094-002 VRK-3W, vert. rigging kit, EVH, white
• ACC000100-001 EVF-UB-BLK, u-bracket kit, EVF, black
• ACC000100-002 EVF-UB-WHT, u-bracket kit, EVF, white
• D170466
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Electro-Voice
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
© Bosch Communications Systems
07/2010
For technical assistance, contact Technical Support at: 866/78AUDIO
Part Number LIT000464564 Rev A
Specifications subject to change without notice.
|