Eagle Tree Systems Network Router ECU JETCAT User Manual

Instruction Manual for the Seagull Jet ECU Interfaces  
Document Version 1.2  
Model #’s ECU-JETCAT, ECU-AMT, ECU-FADEC  
Thank you for your purchase! This instruction manual will guide you through the installation and operation of your Seagull  
Jet ECU Interface. Please read the entire manual carefully before proceeding. If, after you read the manual (including the  
Troubleshooting section!!), you have further questions or problems, see the Support page on  
http://www.eagletreesystems.com for additional information, or email us at [email protected].  
Features and Benefits of the Jet ECU Interface  
The Jet ECU Interface, in conjunction with our Seagull Pro Flight System, provides real-time data and audible feedback  
about the state of your Model Jet, while you are flying! Think of the Jet ECU Interface as a Wireless Engine Data  
Terminal/GSU for your Jet.  
Data such as ECU Turbine RPM, Turbine temperature, Throttle %, ECU Pack and Pump Voltage, and ECU status  
messages are retrieved from your ECU and transmitted wirelessly to the Seagull Dashboard. Audible alarms can be  
programmed for low Turbine RPM and temperature for early flameout alert, and for ECU pack voltage for low battery  
indication. All these parameters are in addition to the standard data parameters that are available on the Pro System.  
In addition to display on the LCD screen of the Wireless Dashboard, if the Dashboard is connected to a laptop via USB,  
all the ECU data are available live with the Windows Virtual Cockpit application!  
Packing List  
Your package should include the following: Jet ECU Interface Cable (either AMT Netherlands, JetCat or FADEC), and a  
printed version of this manual. Please check your box for printed addenda to this manual which may be included if  
changes were made after printing.  
Requirements  
The Jet ECU Interface requires a Seagull Pro Flight System, with Windows application version 3.39 or later. The latest  
version is available on the support page of our website. The Recorder and Dashboard firmware needs to be updated using  
“Tools, Firmware Control.”  
For JetCat users, version 4.00g of the JetCat ECU is required.  
powered with a 4 cell (4.8v pack).  
For AMT Netherlands users, the Recorder must be  
Do you have an ECU that is not currently supported? If so, email us at [email protected] and we may be able  
to help!  
How the Jet ECU Interface Works  
The Jet ECU Interface cable plugs between the Pro Flight Recorder the data/telemetry port of your ECU. After simple  
Windows configuration, the Recorder reads the ECU parameter data and transmits it to the Wireless Dashboard.  
Copyright © 2005 Eagle Tree Systems, LLC  
 
Page 3  
Now, you should see the list of ECU  
parameters that can be displayed on the  
Dashboard, as well as the other Seagull  
Parameters. Select the desired  
parameters and configure alarms on the  
new ECU parameters as described in your  
Seagull Pro Flight System manual.  
Here is specific information about the  
ECU parameters:  
ECU Throttle % - this indicates the  
throttle deflection percentage  
ECU Turbine Temperature – this  
indicates the turbine temperature. Note  
that it is ALWAYS in Degrees C on the  
Dashboard, even if English units are  
selected in the application  
ECU Turbine RPM – this indicates the  
turbine RPM. IMPORTANT: please  
make sure that you place the RPM display  
on either the left upper or left lower  
display location (not on the right side of  
the screen). This is because RPM can go  
about 99,999, which means it won’t  
display properly on the right side.  
ECU Status – this page on the Dashboard  
indicates the status of the ECU. The messages vary depending on which ECU you have, and should be similar to the  
messages your Data Terminal/GSU currently displays. When no ECU is detected, “ECU NOT DETECTED” is displayed  
on the ECU status page of the dashboard.  
ECU Pack Voltage – this indicates the voltage of the ECU’s main power supply.  
ECU Pump Voltage – this indicates the current pump voltage. NOTE: on the FADEC, this indicates the pump duty  
cycle.  
Live Mode Application Display  
All of the ECU parameters can be displayed in application Live Mode, when either the Dashboard or the Recorder is  
connected to your PC/Laptop via USB. To configure the parameters to display in Live Mode, click “Tools, Choose  
Instruments to Display on PC Screen” and the ECU options should appear on the righthand side of this page.  
Range Checking and Flying  
IMPORTANT: It is unlikely that the installation of the Eagle Tree system will cause problems with radio range. But, as  
always, it is critical to do an antenna-down range check, per your jet/radio manufacturer’s instructions, after making any  
changes to your jet’s electronics (and frankly before every flight session). Eagle Tree recommends that the range check  
be done with the turbine running, to completely verify operation (if this can be done safely).  
Happy Flying! We’d love to see pictures of your installation and get your feedback. Just email us at  
Troubleshooting  
Below is a list of problems that may be encountered, and steps to remedy them. If your particular issue is not addressed  
by the below, see the Support page on http://eagletreesystems.com or email us at [email protected].  
Copyright © 2005 Eagle Tree Systems, LLC  
 
Page 4  
Include a full description of your problem, your machine configuration, brand/model/version of ECU, application version,  
Dashboard and Recorder firmware version and any other relevant details.  
Issue: “ECU NOT DETECTED” appears on the ECU Status page of the LCD Dashboard, after configuration  
Solution:  
Make sure you have downloaded the latest Windows application and installed the latest firmware, as described in  
the Requirements section above.  
Make sure you have followed the application configuration instructions above.  
Make sure that you have connected the ECU Interface cable appropriately, as described above.  
Plug in your Engine Data Terminal/GSU, if you have one, and verify that it is reading correctly.  
Issue: I have reduced antenna-down range with the ECU Interface installed  
Solution:  
Try isolating the problem – disconnect the ECU Interface cable, and see if the range improves. If it does not  
improve, please see the Troubleshooting section in the Seagull Pro Flight System user manual. If range does  
change when disconnecting the ECU Interface cable, please contact Eagle Tree Systems immediately.  
Limited Warranty  
Eagle Tree Systems, LLC, warrants the Jet ECU Interface Cable to be free from defects in materials and workmanship for  
a period of one (1) year from the date of original purchase. This warranty is nontransferable. If your unit requires  
warranty service during this period, we will replace or repair it at our option. Shipping cost to us is your responsibility.  
To obtain warranty service, email us to request an RMA number. No returns will be accepted without this number.  
This limited warranty does not cover:  
The Software included with the System. See the Software license agreement for more information on Software  
restrictions.  
Problems that result from:  
o
o
o
o
External causes such as accident, abuse, misuse, or problems with electrical power  
Servicing not authorized by us  
Usage that is not in accordance with product instructions  
Failure to follow the product instructions  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION). OUR RESPONSIBILITY FOR  
MALFUNCITONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET  
FORTH IN THIS WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR THE  
PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES AND CONDITIONS OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE TERM  
OF THE LIMITED WARRANTY PERIOD AS DESCRIBED ABOVE. NO WARRANTIES, WHETHER EXPRESS OR  
IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. SOME STATES DO NOT  
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THIS LIMITATION MAY NOT  
APPLY TO YOU.  
WE DO NOT ACCEPT LIABILITY BEYOND THE REMEDIES PROVIDED FOR IN THIS LIMITED WARRANTY  
OR FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY  
LIABILTY FOR THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES, FOR PRODUCTS NOT BEING  
AVAILABLE FOR USE, OR FOR LOST DATA OR LOST SOFTWARE. OUR LIABILITY WILL BE NO MORE  
THAN THE AMOUNT YOU PAID FOR THE PRODUCT THAT IS THE SUBJECT OF A CLAIM. THIS IS THE  
MAXIMUM AMOUNT FOR WHICH WE ARE RESPONSIBLE.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
Copyright © 2005 Eagle Tree Systems, LLC  
 

Creda Cooktop C150 User Manual
Delta Electronics Power Supply DHCB User Manual
Digicom Network Card SNT09 User Manual
Dixon Lawn Mower 6601 Series User Manual
Fisher Price Car Seat P2792 User Manual
Fisher Price Satellite Radio P6584 User Manual
Foster Oven 7170 052 User Manual
Furman Sound Stereo Equalizer EQ 2151 User Manual
GE Answering Machine 00003287 User Manual
GE Dishwasher EDWSO00 User Manual