OWNER’S MANUAL
1450 Lakeside Drive• Waukegan, Illinois 60085 USA
330-677-4424 • 800-321-6699 • Fax: 330-677-4471
All designs and specifications are subject to change without notice. Copyright © 2006 ETA Systems. 6MAN-030
SPECIFIC FEATURES FOR MODELS:
FEATURE
LIGHT SWITCH
LIGHT TUBES
EPD11LIEC-CE, EPD11LVIEC-CE, EPD11LOIEC-CE
EPD11LIEC-CE, EPD11LVIEC-CE, EPD11LOIEC-CE
EPD10VIEC-CE, EPD11LVIEC-CE
VOLTAGE DISPLAY
CIRCUIT BREAKER
POWER SWITCH
EPD10IEC-CE, EPD10VIEC-CE, EPD11LIEC-CE, EPD11LVIEC-CE
EPD10IEC-CE, EPD10VIEC-CE, EPD11LIEC-CE, EPD11LVIEC-CE
EPD11LIEC-CE, EPD11LVIEC-CE,
(1) FRONT PANEL
IEC320 OUTLET
(1) BACK PANEL
IEC320 MALE INLET
EPD10IEC-CE, EPD10VIEC-CE, EPD11LIEC-CE,EPD11LVIEC-CE, EPD11LOIEC-CE
EPD10IEC-CE, EPD10VIEC-CE, EPD11LIEC-CE,EPD11LVIEC-CE
(10) BACK PANEL
SWITCHED
General Operating Instructions:
1. Install unit in a standard 19-inch (48.25cm) rack or in a free-standing position.
2. Connect Power Distribution/Lights Only unit to 230VAC 50/60Hz power source.
3. Plug sensitive electronic equipment into conditioned outlets on back of unit.
4. Move the power switch (#5) to the "ON" position to provide power and protection to the electrical
equipment.
5. For illumination (Models EPD11LIEC-CE, EPD11LVIEC-CE, and EPDLOIEC-CE), pull out/extend the
light tubes (#2) and move the light switch (#1) to either the "HI" or "LO" positions.
IMPORTANT: Be sure the light switch (#1) is in the "OFF" position when the light tubes are recessed
back inside the unit.
6. The digital voltmeter readout (#3) automatically and continuously displays the incoming voltage to
the unit (Models EPD10VIEC-CE and EPD11LVIEC-CE).
SERVICING:
WARNING: Hazardous voltages are present within the unit. Never attempt any maintenance without
disconnecting the power cord.
ATTENTION: Les tensions de l'appareil présentent des dangers. Déconnectez le cordon d'alimentation
avant d'effectuer toute réparation.
VERWARNEND: Gefährlich stromspannung bist im einheit. Test nicht versuch erhaltung ohne ent-
fernend das gewalt schnur.
AMMONIMENTO: Pericolosa voltaggio siamo presentano negli unità. Do non tentative mantenimento
senza allontanando gli potenza spago.
LAMP REPLACEMENT
REMPLACEMENT DE
LA LAMPE
LAMPE ERSATZ
LAMPADA CAMBI
1. Disconnect the units power cord from the voltage source.
Déconnectez le cordon d'alimentation du secteur.
Loskomme das einheiten gewalt schnur vom stromspannung quelle.
Disinnestano gli units potenza spago dai voltaggio fonte.
2. Remove screws on cover, and remove cover.
Retirez les vis et ôtez le couvercie.
Entferne schraubt an abdeckung, und entferne abdeckung.
Allontanano vites su coperchio, e allontanano coperchio.
3. Remove the two (2) hex spacers and two (2) hex nuts from rear of light tube assembly.
Retirez les (2) deux entretoises et les (2) deux écrous à tête six-pans à l'arrière de chaque assemblage de la lampe.
Entferne das (2) zwei trenner und das (2) zwei riegel halter vom hinter von jede leicht rohr.
Allontanano gli due (2) separatori e gli due (2) bolt raccoglitori dai posteriore di cadauna leggera tubo assemblea.
4. Slide lamp socket out of the tube.
Retirez la lampe de la douille.
Hernehme lampe sockel aus das rohr.
Prendere lampada alloggiando fuori degli tubo.
5. Turn lamp counterclockwise and replace with same type and rating 230-,7W.
Tournez la lampe vers la gauche et remplacez-la par une lampe de même type et de meme calibre (230 V, 7 W).
Drehen lampe ans abfuhr und vertrete mit gleich typ und beurteilung 230-, 7W.
Giro lampada agli partii e rimetterci con stesso tipo e classifica 230-, 7W.
6. Insert lamp sockets into the back of the tube.
Insérez le culot de la lampe dans la douille.
Einfüge lampe sockel rücken im rohr.
Inseriamo lampada alloggiando ritorno negli tubo.
7. Replace the two (2) hexagonal spacers and the two (2) hex nuts at the rear of the light tube assemblies, and
attach the housing bracket to the tube.
Replacez les entretoises et les écrous à l'arrière de l'assemblage de la lampe et attachez le support à la lampe.
Vertrete das zwei (2) trenner und das zwei (2) halter am hinter der leicht rohr, und anhefte das sockel ans rohr.
Rimetterci gli due (2) separatori e gli due (2) nuts at gli posteriore degli leggera tubo assemblee, e annettere gli
alloggiando agli tubo.
8. Replace top cover and screws.
Revissez le couvercie.
Vertrete oberteil abdeckung und schraubt.
Rimetterci cima coperchio e raccoglitori.
9. Connect power cord to voltage source and test lamp.
Connectez le cordon d'alimentation au secteur et vérifiez le bon fonctionnement de la lampe.
Anschliesse gewalt schnur bis stromspannung nachschub und erprobe lampe.
Installano potenza spago a voltaggio fornirle e collaudo lampada.
EU DECLARATION OF CONFORMITY
Information Technology Equipment
Directives covered by this Declaration:
89/336/EEC Electromagnetic Compatibility Directive
73/23/EEC Low Voltage Direction
Product:
ETA Systems - "EPD11LVIEC-CE Series" Power
Distribution Series, Serial Numbers CE20000+
(+ means "and up")
Standard which
Product Conforms to:
IEC950-1, -2, and referencing -3:1995,
or EN60950-3:1995 with all amendments through
Jan. 1997.
The technical documentation required to demonstrate that this product meets the
requirements of the "EMC", and "Low Voltage" Directives, has been compiled by
the signatory below and is available for inspection by the relevant authorities. The
CE Mark was first applied in 1998.
Authority:
Guy LeJeune
Eurocase Belgium N.V.
Daenenstraat 44
Sign:
Date:
B-2600 Berchem-Antwerpen
Phone: 011-32-3-230-9445
Fax: 011-32-3-218-9397
The attention of the purchaser, installer, or user is drawn to the special
measures and limitations which must be observed when the product is
taken into service, in order to maintain compliance with the above
directives. Details of the special measures and requirements are
detailed in this product user manual.
|