XDM6220
INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA Receiver with Detach Face
XDM6220 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio. The
XDM6220 uses one 10 amp
AGC fuse (Battery) located
in-line.
3
XDM6220 OPERATION
Control Locations
3
4
7
8
1
2
5
6
21
20
19
18
17
16
15
14
13
12
11
10
9
Release
Power
Mute
EQ/9
Tuner Scan/8
Local/Distance/7
1
2
3
4
5
6
7
8
9
12
13
14
15
16
17
18
19
Audio
Preset 6/Folder Up
Preset 5/Folder Down
Preset 4
Band/Play/Pause
Auto Store/Preset Scan/Enter
Mode/Search
Preset 3/Intro
Eject
Preset 2/Random
Tune/Track Up/Down
Loudness
20 Preset 1/Repeat
21
10
11
Volume Up/Down
Display/0
The XDM6220 allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
4
XDM6220 OPERATION
General Operation
Faceplate Removal Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Semi-permanent Remove trim ring and install supplied #1 x 7/32” Phillips
Faceplate Installation head screw through left side of mounting frame into faceplate.
Power On/Off Press PWR or any other button (except eject or volume up/
down) to turn the unit on. Inserting a disc will turn the unit
on automatically. Press PWR to turn the unit off.
Mode Press MODE to select between tuner, CD player and auxiliary
input. Modes of operation are indicated in the display.
Loudness Press LOUD to activate and deactivate the loudness contour
curve. Activating this feature will enhance the bass and
treble frequencies when listening to music at low volumes.
Volume Adjust volume using VOL t / VOL s (00-46).
Programmable Press and hold PWR for 3 seconds to program currently
Turn-On Volume selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Preset EQ Curves Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Display Press DISP to select between clock and radio frequency
(tuner mode), clock and CD track/elapsed time (CD mode),
or clock and AUX (AUX mode).
Set the Clock With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE << to adjust the hours
and TUNE >> to adjust the minutes. Press DISP momentarily
to save the selected time.
12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency
:
spacing mode (PM 10 00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
5
XDM6220 OPERATION
General Operation
Programmable Display In tuner mode, press and hold DISP then press TUNE >>
Priority to select function priority display. “FREQ” will momentarily
appear in the display.
Note:
"FUNC" will appear in CD or AUX modes.
Radio frequency (tuner mode), CD track/elapsed time (CD
mode) or AUX (AUX mode) will be displayed by default.
Note:
When playing MP3/WMA files, the track number/elapsed
time, track name, directory name, title, artist, album, year
or comment will be displayed by default. Clock is accessed
by pressing DISP momentarily.
Press and hold DISP then press TUNE << to select time
display priority. “TIME” will momentarily appear in the
display. Clock will be displayed by default. Radio frequency,
CD track/elapsed time or MP3/WMA file information is
accessed by pressing DISP momentarily.
Programmable Clock Programs unit to display clock/no clock when unit is off.
Priority Press and hold MODE then press PRESET 1 to select clock
priority on/off. “CLK ON” or “CLK OFF” will momentarily
appear in the display.
Reset Press and hold for more than 2 seconds to RESET the unit
upon initial installation or if abnormal operation occurs.
The reset button is located behind the faceplate. Refer to
page 2 for details.
Confirmation Beep Press and hold AUD for 3 seconds to turn confirmation
beep on/off. "BEEP ON" or BEEP OFF" will momentarily
appear in the display.
Mute Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
6
XDM6220 OPERATION
General Operation
Audio
Press AUD to select between Volume (default), Bass, Treble,
Balance & Fader.
Bass
Treble
Press AUD until BAS appears
Press VOL t or s to adjust
( -6 minimum / +6 maximum)
Press AUD until TRE appears
Press VOL t or s to adjust
( -6 minimum / +6 maximum)
Balance
Press AUD until BAL appears
Press VOL t or s to adjust
(BAL L 12-BAL 00-BAL R 12)
BAL 00 represents equal balance
Fader
Press AUD until FAD appears
Press VOL t or s to adjust
(FAD F 12-FAD 00-FAD R 12)
FAD 00 represents equal fader
Source Audio Memory
Individual Bass and Treble settings are retained in memory
for AM, FM, CD, and AUX modes. This allows you to save
the Bass and Treble settings separately for each mode.
Example:
FM tuner mode can have Bass +3 and Treble -1 while CD
mode can have Bass +2 and Treble +2.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
7
XDM6220 OPERATION
Tuner Operation
Press TUNE << or TUNE >> momentarily to seek the next
strong station.
Seek Tuning
Press TUNE << or TUNE >> for more than 2 seconds, then
release. "MANUAL" will momentarily appear in the display.
Press TUNE << or TUNE >> momentarily to move radio
frequency up or down one step at a time. Press and hold to
advance quickly. If tuning is not adjusted for 5 seconds, the
unit will return to seek tuning mode (default). "AUTO" will
momentarily appear in the display.
Manual Tuning
Press SCAN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCAN again to cancel.
Scan Tuning
Press LOC to activate local tuning for strong station reception
only. Press LOC again to cancel and resume distance tuning
(default).
Local/Distance
Press BAND to select between FM1, FM2, FM3, AM1 and AM2
Band
bands.
Press and hold BAND then press TUNE << to select
European frequency spacing. Press and hold BAND then
press TUNE >> to select USA frequency spacing (default).
Frequency Spacing
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Storing and Recalling
Station Presets
Note:
Function buttons 7, 8, 9 and 0 apply to MP3 and WMA
playback only.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Local/Distance is activated during the initial band scan.
Automatically Store
Stations
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
Preset Scan
8
XDM6220 OPERATION
CD Player Operation
With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
Insert CD
Eject CD
Press EJECT to eject the CD. The unit will change to previous
mode of operation (AM, FM, or auxiliary input). If the disc is
not removed within 10 seconds, the unit will reload the disc.
The unit does not have to be turned on to eject CD.
Press TRACK >> to skip to the beginning of the next track.
Press TRACK << to return to the beginning of the current
track. Pressing TRACK << again skips to the beginning of
the previous track.
Track Select
Press and hold TRACK >> or TRACK << to fast forward or
reverse a track.
Fast Forward and Reverse
Press
Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
Pause
Intro
l
l
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Repeat
Random
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between tuner, CD player and auxiliary input
modes and when the unit is turned on/off.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CD-R/CD-RW Compatibility
CDs exposed to extreme temperatures or direct sunlight for
extended periods of time, CDs recorded in which a recording
session failed or a re-recording was attempted and, or
encrypted or copy-protected CDs which do not conform to
the audio CD-DA red book recording standard.
9
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
When an MP3/WMA encoded disc is first inserted,
Playing an MP3/WMA Disc
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
The
icon will illuminate anytime a valid MP3 encoded
MP3 Icon
WMA Icon
disc is inserted and flash in MP3 search/navigate modes.
The
icon will illuminate anytime a valid WMA encoded
disc is inserted and flash in WMA search/navigate modes.
Folder Icon
The
icon will illuminate anytime a folder is selected in
the file/folder search modes.
Displaying Information
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist,
album, year and comment.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
Character Support
Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
• *Year – 4 character maximum
• *Comment – 28 character maximum
*Song title, Artist Name, Album name, Year and Comment
will only be displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
10
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
Refer to the following button function table when selecting, searching or
navigating MP3/WMA files and folders:
MP3/WMA Button Function Table
Button
Function
SEARCH
Direct Select, Search and Navigate Modes
Enter/Confirm
A, B, C, 1
Preset 1
Preset 2
D, E, F, 2
Preset 3
G, H, I, 3
Preset 4
J, K, L, 4
Preset 5
M, N, O, 5
Preset 6
P, Q, R, 6
7
S, T, U, 7
8
V, W, X, 8
9
Y, Z, /, 9
0
AUD
-, _, +, 0
Character Shift
Character Select (A, B, C ~ 8, 9, 0)
Character Backspace
VOL t / VOL s
MUTE
Direct Select, Search and
Navigate Modes
Press SEARCH for more than 3 seconds, to select between
the following modes:
• Direct File Select
• Alphanumeric File or Folder Search
• File or Folder Navigate
Direct File Select
Step 1
Press SEARCH for more than 3 seconds, then release.
“MP3 T " or “WMA T ” will flash in the display. Use the
*
*
buttons in the above table (3 keystroke maximum input),
or the VOL t / VOL s to enter the desired file number.
Step 2
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
11
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
Alphanumeric File
or Folder Search
Step 1
Press SEARCH for more than 3 seconds, then release.
Press SEARCH again, an " " will flash in the display. Use
the buttons in the table on page 11 (32 character maximum
input) or the VOL t / VOL s to enter the desired alphanu-
meric search characters. Press AUD to advance one
character to the right.
*
Step 2
Step 3
Press
to initiate the selected alphanumeric search.
Press VOL t / VOL s to preview the search results.
If the search returns a folder, the icon will illuminate.
Step 4
Step 5
Press
to select the desired file or folder. If a folder
is selected, two "/ /" will illuminate. Press VOL s to begin
searching files in the folder.
Press
Note:
to select the desired file within the folder.
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
File/Folder Navigate
Step 1
Press SEARCH for more than 3 seconds, then release.
Press SEARCH again two times to navigate files/folders
on the disc. The current folder name will scroll one time
followed by available files and folders.
Step 2
Step 3
Step 4
Press VOL t / VOL s to preview files/folders in the
current folder. If a folder is selected, the
illuminate.
icon will
Press
to select the desired file or folder. If a folder
is selected, two "/ / " will illuminate. Press VOL s to begin
searching files in the folder.
Press
to select the desired file within the folder.
*Folder Access
(Up one level)
When navigating root folders “/ /“ will illuminate. Press
AUD to access the previous folder level (up one level).
*Only available on MP3/WMA discs recorded with more
than one folder.
12
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
*Folder Access Press F
Press F
to select the previous folder.
to select the next folder.
*Folder access is only available on MP3/WMA discs recorded
with more than one folder.
File Repeat Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
File Repeat Press RPT for more than 2 seconds to consecutively repeat
(Current Folder Only) all files in the current folder only. The
the display when in folder repeat mode.
Press RPT again to cancel.
icon will appear in
Disc Random Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
Folder Random Press RDM for more than 2 seconds to play all files in
current folder only in random order. The
in the display when in folder random mode.
Press RDM again to cancel.
icon will appear
Disc Intro Press INT momentarily to play the first 10 seconds of each
file on the entire MP3/WMA disc. Press INT again to cancel.
Folder Intro Press INT for more than 2 seconds to play the first 10
seconds of each file in the current folder only. The
will appear in the display when in folder intro mode.
Press INT again to cancel.
icon
Note:
File repeat (current folder only), folder random and folder
intro is only available on MP3/WMA discs recorded with
more than one folder.
13
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
Media Compatibility The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order MP3/WMA playback sequence is based on recorded order of
files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
Compatible Recording • ISO9660 level 1
Formats • ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
14
XDM6220 OPERATION
CD Player Operation - MP3/WMA Files
Additional MP3/WMA An internal buffer provides ESP (Electronic Skip Protection)
Information to virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
Sampling Frequency Rates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
Transfer Bit rates
MP3 8kbps ~ 320kbps constant
Variable bit rates
WMA 32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
Recommended Settings For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDM6220 WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls or connections discussed in your
instruction booklet may save you a service
call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
• Call us toll-free at 1-866-382-5476
• Email us at [email protected]
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
16
XDM6220 OPERATION
Specifications
CD Player Signal-to-noise: >92dB
Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1 Bit
FM Tuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Total power output: 200 Watts Peak
Power output: 50Wx4 @ 4 ohms, 14.4 VDC
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)
Design and specifications subject to change without notice.
17
XDM6220 WARRANTY
Troubleshooting
Problem
Cause
Action
Unit will not turn on
(no power)
Yellow wire not connected or incorrect voltage Check connections for proper voltage
Red wire not connected or incorrect voltage
Black wire not connected
Fuse blown
(11~16VDC)
Check connection to ground
Replace fuse
Unit has power
(but no sound)
Speaker wires not connected
Check connections at speakers
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Unit blows fuses
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Excessive skipping
Unit is not mounted correctly or backstrap is Check mounting sleeve and backstrap
not secure support
Physical defect in media (CD, CD-R or CD-RW) Check media for scratches
ERROR-01 appears
on display
Disc read error
Press EJECT or RESET
Press EJECT or RESET
Press EJECT or RESET
Press EJECT or RESET
Press EJECT or RESET
ERROR-02 appears
on display
Focus error or disc is in upside down
FAT error
ERROR-03 appears
on display
ERROR-04 appears
on display
MP3/WMA decode error
PROTECT appears
on display
The WMA file is DRM protected
CD mechanism position out of alignment
CD transit screws still in place
Unit will not accept
a disc
Press EJECT for 3 seconds to reset
CD mechanism position
Remove 2 transit screws located on top
of the unit
18
XDM6220 OPERATION
Notes
19
Dual Electronics Corp.
21318 64th Ave. South
Kent, WA 98032
Toll Free: 1-866-382-5476
©2005 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States and or other countries.
NSA0505-V01
|