DigiPower Battery Charger TC 370 User Manual

7. DO NOT slide the plate all of the way in the charger  
without first clicking it into the grooves as it will not be  
set properly and your battery will not charge.  
8. Once you have inserted the plate correctly, you may  
insert your battery for charging. Make sure to face the  
battery out and have the contacts facing in towards the  
contacts on the charger.  
Item No. TC-370  
DIGITAL CAMERA / CAMCORDER  
ULTRA FAST RAPID  
WORLD TRAVEL CHARGER  
9. Plug the charger in.  
RED LED = unit is charging battery  
ORANGE LED = trickle charge (battery is 80% full)  
GREEN LED = battery is fully charged  
Allow 2 hours for full charge.  
Thank you for purchasing our DigiPower Lithium-Ion  
Ultra Fast Rapid Charger. This unique charger now  
makes it convenient for you charge your batteries with  
almost any AC power source in the World without having  
to add country specific pass through adapters.  
B. For Charging Battery Type:  
The Travel Charger comes equipped with a patented,  
integrated World AC plug that allows you to use your  
Charger around the world in: England, Europe, North  
America, South America, China, Asia, Australia, and  
New Zealand.  
NP-120 or BP-NP120  
1. Remove adaptor plate from charger.  
2. Place NP-120 battery in charger with face up  
and contacts facing the contacts in the charger.  
3. Plug the charger in.  
Charging Instructions:  
RED LED = unit is charging battery  
ORANGE LED = trickle charge (battery is 80% full)  
GREEN LED = battery is fully charged  
Allow 2 hours for full charge.  
A. For Charging Battery Types:  
NP-20 or BP-NP20  
NP-40 or BP-NP40  
NP-60 or BP-NP60  
NP-200 or BP-NP200  
Instructions for Adjusting the  
Multi-Country Plugs:  
A. North America  
1
The TC-370 Charger is equipped with a battery  
adaptor plate.  
1. Locate the black button / latch at the base of the  
charger where the North American / Australian  
Plugs are embedded.  
2. This adaptor plate has two sides.  
Each side is labeled with battery types to be used.  
Side 1 is for NP-40, NP-60 and NP-200 battery types.  
Side 2 is for NP-20 battery type.  
2. Release the North American / Austrailian plug by  
pressing down on the button / latch. Continue to  
push the North American Plug upward until it is  
in a 90 degree position  
No plate is needed for NP-120 battery type.  
3. The plate can be removed from the charger unit, and  
inserted with either side facing out, depending on the  
type of battery you are charging.  
(Figure A).  
4. Remove the plate by pushing it out with your thumb or  
finger just above the LED.  
5. When charging any of the batteries listed above (NP-20,  
NP-40, NP-60 or NP-200) you must face the side of the  
adaptor plate labeled with your battery type out and the  
arrow pointing up toward the LED.  
Figure A  
6. You must insert the adaptor plate by placing it almost all  
the way in and then clicking it into place along the  
grooves. Then push the plate the rest of the way in so it  
locks into place.  
3. You may now place your Lithuim-Ion battery in  
the charger. Insert the plug into a wall outlet  
and begin charging your battery.  
 

Craftsman Air Compressor 91916778 User Manual
Craftsman Tiller 91729331 User Manual
Crosley Refrigerator 241824400 User Manual
Cypress Computer Hardware STK15C88 User Manual
Delta Electronics Network Card TP PCC01 User Manual
Delta Electronics Power Supply HMU1356S User Manual
Delta Electronics Power Supply S48SA User Manual
EverFocus Cable Box EHA SRX User Manual
Gefen Switch GEF DVIKVM 848DL User Manual
GE Monogram Refrigerator ZICS360NX User Manual